| # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) |
| %YAML 1.2 |
| --- |
| $id: http://devicetree.org/schemas/pinctrl/qcom,mdm9615-pinctrl.yaml# |
| $schema: http://devicetree.org/meta-schemas/core.yaml# |
| |
| title: Qualcomm Technologies, Inc. MDM9615 TLMM block |
| |
| maintainers: |
| - Bjorn Andersson <andersson@kernel.org> |
| |
| description: Top Level Mode Multiplexer pin controller in Qualcomm MDM9615 SoC. |
| |
| $ref: /schemas/pinctrl/qcom,tlmm-common.yaml# |
| |
| properties: |
| compatible: |
| const: qcom,mdm9615-pinctrl |
| |
| reg: |
| maxItems: 1 |
| |
| interrupts: |
| maxItems: 1 |
| |
| interrupt-controller: true |
| '#interrupt-cells': true |
| gpio-controller: true |
| '#gpio-cells': true |
| gpio-ranges: true |
| |
| required: |
| - compatible |
| - reg |
| |
| additionalProperties: false |
| |
| patternProperties: |
| "-state$": |
| oneOf: |
| - $ref: "#/$defs/qcom-mdm9615-pinctrl-state" |
| - patternProperties: |
| "-pins$": |
| $ref: "#/$defs/qcom-mdm9615-pinctrl-state" |
| additionalProperties: false |
| |
| $defs: |
| qcom-mdm9615-pinctrl-state: |
| type: object |
| description: |
| Pinctrl node's client devices use subnodes for desired pin configuration. |
| Client device subnodes use below standard properties. |
| $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state |
| |
| properties: |
| pins: |
| description: |
| List of gpio pins affected by the properties specified in this |
| subnode. |
| items: |
| pattern: "^gpio([0-9]|[1-7][0-9]|8[0-7])$" |
| minItems: 1 |
| maxItems: 16 |
| |
| function: |
| description: |
| Specify the alternative function to be configured for the specified |
| pins. |
| |
| enum: [ gpio, gsbi2_i2c, gsbi3, gsbi4, gsbi5_i2c, gsbi5_uart, |
| sdc2, ebi2_lcdc, ps_hold, prim_audio, sec_audio, cdc_mclk, ] |
| |
| bias-disable: true |
| bias-pull-down: true |
| bias-pull-up: true |
| drive-strength: true |
| output-high: true |
| output-low: true |
| input-enable: true |
| |
| required: |
| - pins |
| |
| additionalProperties: false |
| |
| examples: |
| - | |
| #include <dt-bindings/interrupt-controller/arm-gic.h> |
| tlmm: pinctrl@1000000 { |
| compatible = "qcom,mdm9615-pinctrl"; |
| reg = <0x01000000 0x300000>; |
| interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; |
| gpio-controller; |
| gpio-ranges = <&msmgpio 0 0 88>; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| |
| gsbi3-state { |
| pins = "gpio8", "gpio9", "gpio10", "gpio11"; |
| function = "gsbi3"; |
| drive-strength = <8>; |
| bias-disable; |
| }; |
| |
| gsbi5-i2c-state { |
| sda-pins { |
| pins = "gpio16"; |
| function = "gsbi5_i2c"; |
| drive-strength = <8>; |
| bias-disable; |
| }; |
| |
| scl-pins { |
| pins = "gpio17"; |
| function = "gsbi5_i2c"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| }; |
| }; |