blob: 078fb78895937b70f68fd8da964c676297397f95 [file] [log] [blame]
# SPDX-License-Identifier: GPL-2.0
%YAML 1.2
---
$id: http://devicetree.org/schemas/usb/snps,dwc3.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: Synopsys DesignWare USB3 Controller
maintainers:
- Felipe Balbi <balbi@kernel.org>
description:
This is usually a subnode to DWC3 glue to which it is connected, but can also
be presented as a standalone DT node with an optional vendor-specific
compatible string.
allOf:
- $ref: usb-drd.yaml#
- if:
properties:
dr_mode:
const: peripheral
required:
- dr_mode
then:
$ref: usb.yaml#
else:
$ref: usb-xhci.yaml#
properties:
compatible:
contains:
oneOf:
- const: snps,dwc3
- const: synopsys,dwc3
deprecated: true
interrupts:
description:
It's either a single common DWC3 interrupt (dwc_usb3) or individual
interrupts for the host, gadget and DRD modes.
minItems: 1
maxItems: 3
interrupt-names:
minItems: 1
maxItems: 3
oneOf:
- const: dwc_usb3
- items:
enum: [host, peripheral, otg]
clocks:
description:
In general the core supports three types of clocks. bus_early is a
SoC Bus Clock (AHB/AXI/Native). ref generates ITP when the UTMI/ULPI
PHY is suspended. suspend clocks a small part of the USB3 core when
SS PHY in P3. But particular cases may differ from that having less
or more clock sources with another names.
clock-names:
contains:
anyOf:
- enum: [bus_early, ref, suspend]
- true
usb-phy:
minItems: 1
items:
- description: USB2/HS PHY
- description: USB3/SS PHY
phys:
minItems: 1
items:
- description: USB2/HS PHY
- description: USB3/SS PHY
phy-names:
minItems: 1
items:
- const: usb2-phy
- const: usb3-phy
resets:
minItems: 1
snps,usb2-lpm-disable:
description: Indicate if we don't want to enable USB2 HW LPM for host
mode.
type: boolean
snps,usb3_lpm_capable:
description: Determines if platform is USB3 LPM capable
type: boolean
snps,usb2-gadget-lpm-disable:
description: Indicate if we don't want to enable USB2 HW LPM for gadget
mode.
type: boolean
snps,dis-start-transfer-quirk:
description:
When set, disable isoc START TRANSFER command failure SW work-around
for DWC_usb31 version 1.70a-ea06 and prior.
type: boolean
snps,disable_scramble_quirk:
description:
True when SW should disable data scrambling. Only really useful for FPGA
builds.
type: boolean
snps,has-lpm-erratum:
description: True when DWC3 was configured with LPM Erratum enabled
type: boolean
snps,lpm-nyet-threshold:
description: LPM NYET threshold
$ref: /schemas/types.yaml#/definitions/uint8
snps,u2exit_lfps_quirk:
description: Set if we want to enable u2exit lfps quirk
type: boolean
snps,u2ss_inp3_quirk:
description: Set if we enable P3 OK for U2/SS Inactive quirk
type: boolean
snps,req_p1p2p3_quirk:
description:
When set, the core will always request for P1/P2/P3 transition sequence.
type: boolean
snps,del_p1p2p3_quirk:
description:
When set core will delay P1/P2/P3 until a certain amount of 8B10B errors
occur.
type: boolean
snps,del_phy_power_chg_quirk:
description: When set core will delay PHY power change from P0 to P1/P2/P3.
type: boolean
snps,lfps_filter_quirk:
description: When set core will filter LFPS reception.
type: boolean
snps,rx_detect_poll_quirk:
description:
when set core will disable a 400us delay to start Polling LFPS after
RX.Detect.
type: boolean
snps,tx_de_emphasis_quirk:
description: When set core will set Tx de-emphasis value
type: boolean
snps,tx_de_emphasis:
description:
The value driven to the PHY is controlled by the LTSSM during USB3
Compliance mode.
$ref: /schemas/types.yaml#/definitions/uint8
enum:
- 0 # -6dB de-emphasis
- 1 # -3.5dB de-emphasis
- 2 # No de-emphasis
snps,dis_u3_susphy_quirk:
description: When set core will disable USB3 suspend phy
type: boolean
snps,dis_u2_susphy_quirk:
description: When set core will disable USB2 suspend phy
type: boolean
snps,dis_enblslpm_quirk:
description:
When set clears the enblslpm in GUSB2PHYCFG, disabling the suspend signal
to the PHY.
type: boolean
snps,dis-u1-entry-quirk:
description: Set if link entering into U1 needs to be disabled
type: boolean
snps,dis-u2-entry-quirk:
description: Set if link entering into U2 needs to be disabled
type: boolean
snps,dis_rxdet_inp3_quirk:
description:
When set core will disable receiver detection in PHY P3 power state.
type: boolean
snps,dis-u2-freeclk-exists-quirk:
description:
When set, clear the u2_freeclk_exists in GUSB2PHYCFG, specify that USB2
PHY doesn't provide a free-running PHY clock.
type: boolean
snps,dis-del-phy-power-chg-quirk:
description:
When set core will change PHY power from P0 to P1/P2/P3 without delay.
type: boolean
snps,dis-tx-ipgap-linecheck-quirk:
description: When set, disable u2mac linestate check during HS transmit
type: boolean
snps,parkmode-disable-ss-quirk:
description:
When set, all SuperSpeed bus instances in park mode are disabled.
type: boolean
snps,dis_metastability_quirk:
description:
When set, disable metastability workaround. CAUTION! Use only if you are
absolutely sure of it.
type: boolean
snps,dis-split-quirk:
description:
When set, change the way URBs are handled by the driver. Needed to
avoid -EPROTO errors with usbhid on some devices (Hikey 970).
type: boolean
snps,is-utmi-l1-suspend:
description:
True when DWC3 asserts output signal utmi_l1_suspend_n, false when
asserts utmi_sleep_n.
type: boolean
snps,hird-threshold:
description: HIRD threshold
$ref: /schemas/types.yaml#/definitions/uint8
snps,hsphy_interface:
description:
High-Speed PHY interface selection between UTMI+ and ULPI when the
DWC_USB3_HSPHY_INTERFACE has value 3.
$ref: /schemas/types.yaml#/definitions/uint8
enum: [utmi, ulpi]
snps,quirk-frame-length-adjustment:
description:
Value for GFLADJ_30MHZ field of GFLADJ register for post-silicon frame
length adjustment when the fladj_30mhz_sdbnd signal is invalid or
incorrect.
$ref: /schemas/types.yaml#/definitions/uint32
minimum: 0
maximum: 0x3f
snps,rx-thr-num-pkt-prd:
description:
Periodic ESS RX packet threshold count (host mode only). Set this and
snps,rx-max-burst-prd to a valid, non-zero value 1-16 (DWC_usb31
programming guide section 1.2.4) to enable periodic ESS RX threshold.
$ref: /schemas/types.yaml#/definitions/uint8
minimum: 1
maximum: 16
snps,rx-max-burst-prd:
description:
Max periodic ESS RX burst size (host mode only). Set this and
snps,rx-thr-num-pkt-prd to a valid, non-zero value 1-16 (DWC_usb31
programming guide section 1.2.4) to enable periodic ESS RX threshold.
$ref: /schemas/types.yaml#/definitions/uint8
minimum: 1
maximum: 16
snps,tx-thr-num-pkt-prd:
description:
Periodic ESS TX packet threshold count (host mode only). Set this and
snps,tx-max-burst-prd to a valid, non-zero value 1-16 (DWC_usb31
programming guide section 1.2.3) to enable periodic ESS TX threshold.
$ref: /schemas/types.yaml#/definitions/uint8
minimum: 1
maximum: 16
snps,tx-max-burst-prd:
description:
Max periodic ESS TX burst size (host mode only). Set this and
snps,tx-thr-num-pkt-prd to a valid, non-zero value 1-16 (DWC_usb31
programming guide section 1.2.3) to enable periodic ESS TX threshold.
$ref: /schemas/types.yaml#/definitions/uint8
minimum: 1
maximum: 16
tx-fifo-resize:
description: Determines if the TX fifos can be dynamically resized depending
on the number of IN endpoints used and if bursting is supported. This
may help improve bandwidth on platforms with higher system latencies, as
increased fifo space allows for the controller to prefetch data into its
internal memory.
type: boolean
tx-fifo-max-num:
description: Specifies the max number of packets the txfifo resizing logic
can account for when higher endpoint bursting is used. (bMaxBurst > 6) The
higher the number, the more fifo space the txfifo resizing logic will
allocate for that endpoint.
$ref: /schemas/types.yaml#/definitions/uint8
minimum: 3
snps,incr-burst-type-adjustment:
description:
Value for INCR burst type of GSBUSCFG0 register, undefined length INCR
burst type enable and INCRx type. A single value means INCRX burst mode
enabled. If more than one value specified, undefined length INCR burst
type will be enabled with burst lengths utilized up to the maximum
of the values passed in this property.
$ref: /schemas/types.yaml#/definitions/uint32-array
minItems: 1
maxItems: 8
uniqueItems: true
items:
enum: [1, 4, 8, 16, 32, 64, 128, 256]
unevaluatedProperties: false
required:
- compatible
- reg
- interrupts
examples:
- |
usb@4a030000 {
compatible = "snps,dwc3";
reg = <0x4a030000 0xcfff>;
interrupts = <0 92 4>;
usb-phy = <&usb2_phy>, <&usb3_phy>;
snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;
};
- |
usb@4a000000 {
compatible = "snps,dwc3";
reg = <0x4a000000 0xcfff>;
interrupts = <0 92 4>;
clocks = <&clk 1>, <&clk 2>, <&clk 3>;
clock-names = "bus_early", "ref", "suspend";
phys = <&usb2_phy>, <&usb3_phy>;
phy-names = "usb2-phy", "usb3-phy";
snps,dis_u2_susphy_quirk;
snps,dis_enblslpm_quirk;
};
...