blob: 74e0444af19bf537e195b7d85bedfdaeca43173c [file] [log] [blame]
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
// Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.xyz>
// Based on sun50i-h5-orangepi-pc2.dts, which is:
// Copyright (C) 2016 ARM Ltd.
/dts-v1/;
#include "sun50i-h5.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
/ {
model = "Xunlong Orange Pi Prime";
compatible = "xunlong,orangepi-prime", "allwinner,sun50i-h5";
aliases {
ethernet0 = &emac;
serial0 = &uart0;
};
chosen {
stdout-path = "serial0:115200n8";
};
connector {
compatible = "hdmi-connector";
type = "a";
port {
hdmi_con_in: endpoint {
remote-endpoint = <&hdmi_out_con>;
};
};
};
leds {
compatible = "gpio-leds";
led-0 {
label = "orangepi:green:pwr";
gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
default-state = "on";
};
led-1 {
label = "orangepi:red:status";
gpios = <&pio 0 20 GPIO_ACTIVE_HIGH>;
};
};
r-gpio-keys {
compatible = "gpio-keys";
sw4 {
label = "sw4";
linux,code = <BTN_0>;
gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
};
};
reg_gmac_3v3: gmac-3v3 {
compatible = "regulator-fixed";
regulator-name = "gmac-3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
startup-delay-us = <100000>;
enable-active-high;
gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
};
reg_vcc3v3: vcc3v3 {
compatible = "regulator-fixed";
regulator-name = "vcc3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
reg_usb0_vbus: usb0-vbus {
compatible = "regulator-fixed";
regulator-name = "usb0-vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
enable-active-high;
gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
status = "okay";
};
wifi_pwrseq: wifi_pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&pio 2 14 GPIO_ACTIVE_LOW>; /* PC14 */
};
};
&codec {
allwinner,audio-routing =
"Line Out", "LINEOUT",
"MIC1", "Mic",
"Mic", "MBIAS";
status = "okay";
};
&de {
status = "okay";
};
&ehci0 {
status = "okay";
};
&ehci1 {
status = "okay";
};
&ehci2 {
status = "okay";
};
&ehci3 {
status = "okay";
};
&emac {
pinctrl-names = "default";
pinctrl-0 = <&emac_rgmii_pins>;
phy-supply = <&reg_gmac_3v3>;
phy-handle = <&ext_rgmii_phy>;
phy-mode = "rgmii-id";
status = "okay";
};
&external_mdio {
ext_rgmii_phy: ethernet-phy@1 {
compatible = "ethernet-phy-ieee802.3-c22";
reg = <1>;
};
};
&hdmi {
status = "okay";
};
&hdmi_out {
hdmi_out_con: endpoint {
remote-endpoint = <&hdmi_con_in>;
};
};
&ir {
pinctrl-names = "default";
pinctrl-0 = <&r_ir_rx_pin>;
status = "okay";
};
&mmc0 {
vmmc-supply = <&reg_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
status = "okay";
};
&mmc1 {
vmmc-supply = <&reg_vcc3v3>;
mmc-pwrseq = <&wifi_pwrseq>;
bus-width = <4>;
non-removable;
status = "okay";
};
&ohci0 {
status = "okay";
};
&ohci1 {
status = "okay";
};
&ohci2 {
status = "okay";
};
&ohci3 {
status = "okay";
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pa_pins>;
status = "okay";
};
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&uart1_pins>;
status = "disabled";
};
&uart2 {
pinctrl-names = "default";
pinctrl-0 = <&uart2_pins>;
status = "disabled";
};
&usb_otg {
dr_mode = "otg";
status = "okay";
};
&usbphy {
/* USB Type-A ports' VBUS is always on */
usb0_id_det-gpios = <&pio 0 21 GPIO_ACTIVE_HIGH>; /* PA21 */
usb0_vbus-supply = <&reg_usb0_vbus>;
status = "okay";
};