| // SPDX-License-Identifier: GPL-2.0-or-later |
| /* |
| * eisa.c - provide support for EISA adapters in PA-RISC machines |
| * |
| * Copyright (c) 2001 Matthew Wilcox for Hewlett Packard |
| * Copyright (c) 2001 Daniel Engstrom <5116@telia.com> |
| * |
| * There are two distinct EISA adapters. Mongoose is found in machines |
| * before the 712; then the Wax ASIC is used. To complicate matters, the |
| * Wax ASIC also includes a PS/2 and RS-232 controller, but those are |
| * dealt with elsewhere; this file is concerned only with the EISA portions |
| * of Wax. |
| * |
| * HINT: |
| * ----- |
| * To allow an ISA card to work properly in the EISA slot you need to |
| * set an edge trigger level. This may be done on the palo command line |
| * by adding the kernel parameter "eisa_irq_edge=n,n2,[...]]", with |
| * n and n2 as the irq levels you want to use. |
| * |
| * Example: "eisa_irq_edge=10,11" allows ISA cards to operate at |
| * irq levels 10 and 11. |
| */ |
| |
| #include <linux/init.h> |
| #include <linux/ioport.h> |
| #include <linux/interrupt.h> |
| #include <linux/kernel.h> |
| #include <linux/module.h> |
| #include <linux/pci.h> |
| #include <linux/spinlock.h> |
| #include <linux/eisa.h> |
| |
| #include <asm/byteorder.h> |
| #include <asm/io.h> |
| #include <asm/hardware.h> |
| #include <asm/processor.h> |
| #include <asm/parisc-device.h> |
| #include <asm/delay.h> |
| #include <asm/eisa_bus.h> |
| #include <asm/eisa_eeprom.h> |
| |
| #include "iommu.h" |
| |
| #if 0 |
| #define EISA_DBG(msg, arg...) printk(KERN_DEBUG "eisa: " msg, ## arg) |
| #else |
| #define EISA_DBG(msg, arg...) |
| #endif |
| |
| #define SNAKES_EEPROM_BASE_ADDR 0xF0810400 |
| #define MIRAGE_EEPROM_BASE_ADDR 0xF00C0400 |
| |
| static DEFINE_SPINLOCK(eisa_irq_lock); |
| |
| void __iomem *eisa_eeprom_addr __read_mostly; |
| |
| /* We can only have one EISA adapter in the system because neither |
| * implementation can be flexed. |
| */ |
| static struct eisa_ba { |
| struct pci_hba_data hba; |
| unsigned long eeprom_addr; |
| struct eisa_root_device root; |
| } eisa_dev; |
| |
| /* Port ops */ |
| |
| static inline unsigned long eisa_permute(unsigned short port) |
| { |
| if (port & 0x300) { |
| return 0xfc000000 | ((port & 0xfc00) >> 6) |
| | ((port & 0x3f8) << 9) | (port & 7); |
| } else { |
| return 0xfc000000 | port; |
| } |
| } |
| |
| unsigned char eisa_in8(unsigned short port) |
| { |
| if (EISA_bus) |
| return gsc_readb(eisa_permute(port)); |
| return 0xff; |
| } |
| |
| unsigned short eisa_in16(unsigned short port) |
| { |
| if (EISA_bus) |
| return le16_to_cpu(gsc_readw(eisa_permute(port))); |
| return 0xffff; |
| } |
| |
| unsigned int eisa_in32(unsigned short port) |
| { |
| if (EISA_bus) |
| return le32_to_cpu(gsc_readl(eisa_permute(port))); |
| return 0xffffffff; |
| } |
| |
| void eisa_out8(unsigned char data, unsigned short port) |
| { |
| if (EISA_bus) |
| gsc_writeb(data, eisa_permute(port)); |
| } |
| |
| void eisa_out16(unsigned short data, unsigned short port) |
| { |
| if (EISA_bus) |
| gsc_writew(cpu_to_le16(data), eisa_permute(port)); |
| } |
| |
| void eisa_out32(unsigned int data, unsigned short port) |
| { |
| if (EISA_bus) |
| gsc_writel(cpu_to_le32(data), eisa_permute(port)); |
| } |
| |
| #ifndef CONFIG_PCI |
| /* We call these directly without PCI. See asm/io.h. */ |
| EXPORT_SYMBOL(eisa_in8); |
| EXPORT_SYMBOL(eisa_in16); |
| EXPORT_SYMBOL(eisa_in32); |
| EXPORT_SYMBOL(eisa_out8); |
| EXPORT_SYMBOL(eisa_out16); |
| EXPORT_SYMBOL(eisa_out32); |
| #endif |
| |
| /* Interrupt handling */ |
| |
| /* cached interrupt mask registers */ |
| static int master_mask; |
| static int slave_mask; |
| |
| /* the trig level can be set with the |
| * eisa_irq_edge=n,n,n commandline parameter |
| * We should really read this from the EEPROM |
| * in the furure. |
| */ |
| /* irq 13,8,2,1,0 must be edge */ |
| static unsigned int eisa_irq_level __read_mostly; /* default to edge triggered */ |
| |
| |
| /* called by free irq */ |
| static void eisa_mask_irq(struct irq_data *d) |
| { |
| unsigned int irq = d->irq; |
| unsigned long flags; |
| |
| EISA_DBG("disable irq %d\n", irq); |
| /* just mask for now */ |
| spin_lock_irqsave(&eisa_irq_lock, flags); |
| if (irq & 8) { |
| slave_mask |= (1 << (irq&7)); |
| eisa_out8(slave_mask, 0xa1); |
| } else { |
| master_mask |= (1 << (irq&7)); |
| eisa_out8(master_mask, 0x21); |
| } |
| spin_unlock_irqrestore(&eisa_irq_lock, flags); |
| EISA_DBG("pic0 mask %02x\n", eisa_in8(0x21)); |
| EISA_DBG("pic1 mask %02x\n", eisa_in8(0xa1)); |
| } |
| |
| /* called by request irq */ |
| static void eisa_unmask_irq(struct irq_data *d) |
| { |
| unsigned int irq = d->irq; |
| unsigned long flags; |
| EISA_DBG("enable irq %d\n", irq); |
| |
| spin_lock_irqsave(&eisa_irq_lock, flags); |
| if (irq & 8) { |
| slave_mask &= ~(1 << (irq&7)); |
| eisa_out8(slave_mask, 0xa1); |
| } else { |
| master_mask &= ~(1 << (irq&7)); |
| eisa_out8(master_mask, 0x21); |
| } |
| spin_unlock_irqrestore(&eisa_irq_lock, flags); |
| EISA_DBG("pic0 mask %02x\n", eisa_in8(0x21)); |
| EISA_DBG("pic1 mask %02x\n", eisa_in8(0xa1)); |
| } |
| |
| static struct irq_chip eisa_interrupt_type = { |
| .name = "EISA", |
| .irq_unmask = eisa_unmask_irq, |
| .irq_mask = eisa_mask_irq, |
| }; |
| |
| static irqreturn_t eisa_irq(int wax_irq, void *intr_dev) |
| { |
| int irq = gsc_readb(0xfc01f000); /* EISA supports 16 irqs */ |
| unsigned long flags; |
| |
| spin_lock_irqsave(&eisa_irq_lock, flags); |
| /* read IRR command */ |
| eisa_out8(0x0a, 0x20); |
| eisa_out8(0x0a, 0xa0); |
| |
| EISA_DBG("irq IAR %02x 8259-1 irr %02x 8259-2 irr %02x\n", |
| irq, eisa_in8(0x20), eisa_in8(0xa0)); |
| |
| /* read ISR command */ |
| eisa_out8(0x0a, 0x20); |
| eisa_out8(0x0a, 0xa0); |
| EISA_DBG("irq 8259-1 isr %02x imr %02x 8259-2 isr %02x imr %02x\n", |
| eisa_in8(0x20), eisa_in8(0x21), eisa_in8(0xa0), eisa_in8(0xa1)); |
| |
| irq &= 0xf; |
| |
| /* mask irq and write eoi */ |
| if (irq & 8) { |
| slave_mask |= (1 << (irq&7)); |
| eisa_out8(slave_mask, 0xa1); |
| eisa_out8(0x60 | (irq&7),0xa0);/* 'Specific EOI' to slave */ |
| eisa_out8(0x62, 0x20); /* 'Specific EOI' to master-IRQ2 */ |
| |
| } else { |
| master_mask |= (1 << (irq&7)); |
| eisa_out8(master_mask, 0x21); |
| eisa_out8(0x60|irq, 0x20); /* 'Specific EOI' to master */ |
| } |
| spin_unlock_irqrestore(&eisa_irq_lock, flags); |
| |
| generic_handle_irq(irq); |
| |
| spin_lock_irqsave(&eisa_irq_lock, flags); |
| /* unmask */ |
| if (irq & 8) { |
| slave_mask &= ~(1 << (irq&7)); |
| eisa_out8(slave_mask, 0xa1); |
| } else { |
| master_mask &= ~(1 << (irq&7)); |
| eisa_out8(master_mask, 0x21); |
| } |
| spin_unlock_irqrestore(&eisa_irq_lock, flags); |
| return IRQ_HANDLED; |
| } |
| |
| static irqreturn_t dummy_irq2_handler(int _, void *dev) |
| { |
| printk(KERN_ALERT "eisa: uhh, irq2?\n"); |
| return IRQ_HANDLED; |
| } |
| |
| static struct irqaction irq2_action = { |
| .handler = dummy_irq2_handler, |
| .name = "cascade", |
| }; |
| |
| static void init_eisa_pic(void) |
| { |
| unsigned long flags; |
| |
| spin_lock_irqsave(&eisa_irq_lock, flags); |
| |
| eisa_out8(0xff, 0x21); /* mask during init */ |
| eisa_out8(0xff, 0xa1); /* mask during init */ |
| |
| /* master pic */ |
| eisa_out8(0x11, 0x20); /* ICW1 */ |
| eisa_out8(0x00, 0x21); /* ICW2 */ |
| eisa_out8(0x04, 0x21); /* ICW3 */ |
| eisa_out8(0x01, 0x21); /* ICW4 */ |
| eisa_out8(0x40, 0x20); /* OCW2 */ |
| |
| /* slave pic */ |
| eisa_out8(0x11, 0xa0); /* ICW1 */ |
| eisa_out8(0x08, 0xa1); /* ICW2 */ |
| eisa_out8(0x02, 0xa1); /* ICW3 */ |
| eisa_out8(0x01, 0xa1); /* ICW4 */ |
| eisa_out8(0x40, 0xa0); /* OCW2 */ |
| |
| udelay(100); |
| |
| slave_mask = 0xff; |
| master_mask = 0xfb; |
| eisa_out8(slave_mask, 0xa1); /* OCW1 */ |
| eisa_out8(master_mask, 0x21); /* OCW1 */ |
| |
| /* setup trig level */ |
| EISA_DBG("EISA edge/level %04x\n", eisa_irq_level); |
| |
| eisa_out8(eisa_irq_level&0xff, 0x4d0); /* Set all irq's to edge */ |
| eisa_out8((eisa_irq_level >> 8) & 0xff, 0x4d1); |
| |
| EISA_DBG("pic0 mask %02x\n", eisa_in8(0x21)); |
| EISA_DBG("pic1 mask %02x\n", eisa_in8(0xa1)); |
| EISA_DBG("pic0 edge/level %02x\n", eisa_in8(0x4d0)); |
| EISA_DBG("pic1 edge/level %02x\n", eisa_in8(0x4d1)); |
| |
| spin_unlock_irqrestore(&eisa_irq_lock, flags); |
| } |
| |
| /* Device initialisation */ |
| |
| #define is_mongoose(dev) (dev->id.sversion == 0x00076) |
| |
| static int __init eisa_probe(struct parisc_device *dev) |
| { |
| int i, result; |
| |
| char *name = is_mongoose(dev) ? "Mongoose" : "Wax"; |
| |
| printk(KERN_INFO "%s EISA Adapter found at 0x%08lx\n", |
| name, (unsigned long)dev->hpa.start); |
| |
| eisa_dev.hba.dev = dev; |
| eisa_dev.hba.iommu = ccio_get_iommu(dev); |
| |
| eisa_dev.hba.lmmio_space.name = "EISA"; |
| eisa_dev.hba.lmmio_space.start = F_EXTEND(0xfc000000); |
| eisa_dev.hba.lmmio_space.end = F_EXTEND(0xffbfffff); |
| eisa_dev.hba.lmmio_space.flags = IORESOURCE_MEM; |
| result = ccio_request_resource(dev, &eisa_dev.hba.lmmio_space); |
| if (result < 0) { |
| printk(KERN_ERR "EISA: failed to claim EISA Bus address space!\n"); |
| return result; |
| } |
| eisa_dev.hba.io_space.name = "EISA"; |
| eisa_dev.hba.io_space.start = 0; |
| eisa_dev.hba.io_space.end = 0xffff; |
| eisa_dev.hba.lmmio_space.flags = IORESOURCE_IO; |
| result = request_resource(&ioport_resource, &eisa_dev.hba.io_space); |
| if (result < 0) { |
| printk(KERN_ERR "EISA: failed to claim EISA Bus port space!\n"); |
| return result; |
| } |
| pcibios_register_hba(&eisa_dev.hba); |
| |
| result = request_irq(dev->irq, eisa_irq, IRQF_SHARED, "EISA", &eisa_dev); |
| if (result) { |
| printk(KERN_ERR "EISA: request_irq failed!\n"); |
| goto error_release; |
| } |
| |
| /* Reserve IRQ2 */ |
| setup_irq(2, &irq2_action); |
| for (i = 0; i < 16; i++) { |
| irq_set_chip_and_handler(i, &eisa_interrupt_type, |
| handle_simple_irq); |
| } |
| |
| EISA_bus = 1; |
| |
| if (dev->num_addrs) { |
| /* newer firmware hand out the eeprom address */ |
| eisa_dev.eeprom_addr = dev->addr[0]; |
| } else { |
| /* old firmware, need to figure out the box */ |
| if (is_mongoose(dev)) { |
| eisa_dev.eeprom_addr = SNAKES_EEPROM_BASE_ADDR; |
| } else { |
| eisa_dev.eeprom_addr = MIRAGE_EEPROM_BASE_ADDR; |
| } |
| } |
| eisa_eeprom_addr = ioremap(eisa_dev.eeprom_addr, HPEE_MAX_LENGTH); |
| if (!eisa_eeprom_addr) { |
| result = -ENOMEM; |
| printk(KERN_ERR "EISA: ioremap failed!\n"); |
| goto error_free_irq; |
| } |
| result = eisa_enumerator(eisa_dev.eeprom_addr, &eisa_dev.hba.io_space, |
| &eisa_dev.hba.lmmio_space); |
| init_eisa_pic(); |
| |
| if (result >= 0) { |
| /* FIXME : Don't enumerate the bus twice. */ |
| eisa_dev.root.dev = &dev->dev; |
| dev_set_drvdata(&dev->dev, &eisa_dev.root); |
| eisa_dev.root.bus_base_addr = 0; |
| eisa_dev.root.res = &eisa_dev.hba.io_space; |
| eisa_dev.root.slots = result; |
| eisa_dev.root.dma_mask = 0xffffffff; /* wild guess */ |
| if (eisa_root_register (&eisa_dev.root)) { |
| printk(KERN_ERR "EISA: Failed to register EISA root\n"); |
| result = -ENOMEM; |
| goto error_iounmap; |
| } |
| } |
| |
| return 0; |
| |
| error_iounmap: |
| iounmap(eisa_eeprom_addr); |
| error_free_irq: |
| free_irq(dev->irq, &eisa_dev); |
| error_release: |
| release_resource(&eisa_dev.hba.io_space); |
| return result; |
| } |
| |
| static const struct parisc_device_id eisa_tbl[] __initconst = { |
| { HPHW_BA, HVERSION_REV_ANY_ID, HVERSION_ANY_ID, 0x00076 }, /* Mongoose */ |
| { HPHW_BA, HVERSION_REV_ANY_ID, HVERSION_ANY_ID, 0x00090 }, /* Wax EISA */ |
| { 0, } |
| }; |
| |
| MODULE_DEVICE_TABLE(parisc, eisa_tbl); |
| |
| static struct parisc_driver eisa_driver __refdata = { |
| .name = "eisa_ba", |
| .id_table = eisa_tbl, |
| .probe = eisa_probe, |
| }; |
| |
| void __init eisa_init(void) |
| { |
| register_parisc_driver(&eisa_driver); |
| } |
| |
| |
| static unsigned int eisa_irq_configured; |
| void eisa_make_irq_level(int num) |
| { |
| if (eisa_irq_configured& (1<<num)) { |
| printk(KERN_WARNING |
| "IRQ %d polarity configured twice (last to level)\n", |
| num); |
| } |
| eisa_irq_level |= (1<<num); /* set the corresponding bit */ |
| eisa_irq_configured |= (1<<num); /* set the corresponding bit */ |
| } |
| |
| void eisa_make_irq_edge(int num) |
| { |
| if (eisa_irq_configured& (1<<num)) { |
| printk(KERN_WARNING |
| "IRQ %d polarity configured twice (last to edge)\n", |
| num); |
| } |
| eisa_irq_level &= ~(1<<num); /* clear the corresponding bit */ |
| eisa_irq_configured |= (1<<num); /* set the corresponding bit */ |
| } |
| |
| static int __init eisa_irq_setup(char *str) |
| { |
| char *cur = str; |
| int val; |
| |
| EISA_DBG("IRQ setup\n"); |
| while (cur != NULL) { |
| char *pe; |
| |
| val = (int) simple_strtoul(cur, &pe, 0); |
| if (val > 15 || val < 0) { |
| printk(KERN_ERR "eisa: EISA irq value are 0-15\n"); |
| continue; |
| } |
| if (val == 2) { |
| val = 9; |
| } |
| eisa_make_irq_edge(val); /* clear the corresponding bit */ |
| EISA_DBG("setting IRQ %d to edge-triggered mode\n", val); |
| |
| if ((cur = strchr(cur, ','))) { |
| cur++; |
| } else { |
| break; |
| } |
| } |
| return 1; |
| } |
| |
| __setup("eisa_irq_edge=", eisa_irq_setup); |
| |