arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts - linux - Git at Google

 // SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
 /*
  * Copyright 2020-2021 TQ-Systems GmbH
  */

 /dts-v1/;

 #include "imx8mm-tqma8mqml.dtsi"
 #include "mba8mx.dtsi"

 / {
 	model = "TQ-Systems GmbH i.MX8MM TQMa8MxML on MBa8Mx";
 	compatible = "tq,imx8mm-tqma8mqml-mba8mx", "tq,imx8mm-tqma8mqml", "fsl,imx8mm";
 	chassis-type = "embedded";

 	aliases {
 		eeprom0 = &eeprom3;
 		mmc0 = &usdhc3;
 		mmc1 = &usdhc2;
 		mmc2 = &usdhc1;
 		rtc0 = &pcf85063;
 		rtc1 = &snvs_rtc;
 	};

 	reg_usdhc2_vmmc: regulator-vmmc {
 		compatible = "regulator-fixed";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
 		regulator-name = "VSD_3V3";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 		gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
 		enable-active-high;
 		startup-delay-us = <100>;
 		off-on-delay-us = <12000>;
 	};

 	connector {
 		compatible = "gpio-usb-b-connector", "usb-b-connector";
 		type = "micro";
 		label = "X19";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_usb1_connector>;
 		id-gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;

 		ports {
 			#address-cells = <1>;
 			#size-cells = <0>;

 			port@0 {
 				reg = <0>;
 				usb_dr_connector: endpoint {
 					remote-endpoint = <&usb1_drd_sw>;
 				};
 			};
 		};
 	};
 };

 &i2c1 {
 	expander2: gpio@27 {
 		compatible = "nxp,pca9555";
 		reg = <0x27>;
 		gpio-controller;
 		#gpio-cells = <2>;
 		vcc-supply = <&reg_vcc_3v3>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_expander>;
 		interrupt-parent = <&gpio1>;
 		interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 	};
 };

 &pcie_phy {
 	clocks = <&pcie0_refclk>;
 	status = "okay";
 };

 &pcie0 {
 	reset-gpio = <&expander0 14 GPIO_ACTIVE_LOW>;
 	clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, <&pcie0_refclk>,
 		 <&clk IMX8MM_CLK_PCIE1_AUX>;
 	assigned-clocks = <&clk IMX8MM_CLK_PCIE1_AUX>,
 				<&clk IMX8MM_CLK_PCIE1_CTRL>;
 	assigned-clock-rates = <10000000>, <250000000>;
 	assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_50M>,
 				<&clk IMX8MM_SYS_PLL2_250M>;
 	status = "okay";
 };

 &sai3 {
 	assigned-clocks = <&clk IMX8MM_CLK_SAI3>;
 	assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>;
 	clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3", "pll8k", "pll11k";
 	clocks = <&clk IMX8MM_CLK_SAI3_IPG>, <&clk IMX8MM_CLK_DUMMY>,
 		<&clk IMX8MM_CLK_SAI3_ROOT>, <&clk IMX8MM_CLK_DUMMY>,
 		<&clk IMX8MM_CLK_DUMMY>, <&clk IMX8MM_AUDIO_PLL1_OUT>,
 		<&clk IMX8MM_AUDIO_PLL2_OUT>;
 };

 &tlv320aic3x04 {
 	clock-names = "mclk";
 	clocks = <&clk IMX8MM_CLK_SAI3_ROOT>;
 };

 &uart1 {
 	assigned-clocks = <&clk IMX8MM_CLK_UART1>;
 	assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
 };

 &uart2 {
 	assigned-clocks = <&clk IMX8MM_CLK_UART2>;
 	assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
 };

 &usbotg1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usbotg1>;
 	dr_mode = "otg";
 	srp-disable;
 	hnp-disable;
 	adp-disable;
 	power-active-high;
 	over-current-active-low;
 	usb-role-switch;
 	status = "okay";

 	port {
 		usb1_drd_sw: endpoint {
 			remote-endpoint = <&usb_dr_connector>;
 		};
 	};
 };

 &usbotg2 {
 	dr_mode = "host";
 	disable-over-current;
 	vbus-supply = <&reg_hub_vbus>;
 	status = "okay";
 };

 &iomuxc {
 	pinctrl_ecspi1: ecspi1grp {
 		fsl,pins = <MX8MM_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK	0x00000006>,
 			   <MX8MM_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI	0x00000006>,
 			   <MX8MM_IOMUXC_ECSPI1_MISO_ECSPI1_MISO	0x00000006>,
 			   <MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9		0x00000006>;
 	};

 	pinctrl_ecspi2: ecspi2grp {
 		fsl,pins = <MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK	0x00000006>,
 			   <MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI	0x00000006>,
 			   <MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO	0x00000006>,
 			   <MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13		0x00000006>;
 	};

 	pinctrl_expander: expandergrp {
 		fsl,pins = <MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9		0x94>;
 	};

 	pinctrl_fec1: fec1grp {
 		fsl,pins = <MX8MM_IOMUXC_ENET_MDC_ENET1_MDC		0x40000002>,
 			   <MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO		0x40000002>,
 			   <MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3	0x14>,
 			   <MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2	0x14>,
 			   <MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1	0x14>,
 			   <MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0	0x14>,
 			   <MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3	0x90>,
 			   <MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2	0x90>,
 			   <MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1	0x90>,
 			   <MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0	0x90>,
 			   <MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC	0x14>,
 			   <MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC	0x90>,
 			   <MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x90>,
 			   <MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL	0x14>;
 	};

 	pinctrl_gpiobutton: gpiobuttongrp {
 		fsl,pins = <MX8MM_IOMUXC_GPIO1_IO05_GPIO1_IO5		0x84>,
 			   <MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7		0x84>,
 			   <MX8MM_IOMUXC_SD1_CLK_GPIO2_IO0		0x84>;
 	};

 	pinctrl_gpioled: gpioledgrp {
 		fsl,pins = <MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0		0x84>,
 			   <MX8MM_IOMUXC_NAND_DQS_GPIO3_IO14		0x84>;
 	};

 	pinctrl_i2c2: i2c2grp {
 		fsl,pins = <MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL		0x40000004>,
 			   <MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA		0x40000004>;
 	};

 	pinctrl_i2c2_gpio: i2c2gpiogrp {
 		fsl,pins = <MX8MM_IOMUXC_I2C2_SCL_GPIO5_IO16		0x40000004>,
 			   <MX8MM_IOMUXC_I2C2_SDA_GPIO5_IO17		0x40000004>;
 	};

 	pinctrl_i2c3: i2c3grp {
 		fsl,pins = <MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL		0x40000004>,
 			   <MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA		0x40000004>;
 	};

 	pinctrl_i2c3_gpio: i2c3gpiogrp {
 		fsl,pins = <MX8MM_IOMUXC_I2C3_SCL_GPIO5_IO18		0x40000004>,
 			   <MX8MM_IOMUXC_I2C3_SDA_GPIO5_IO19		0x40000004>;
 	};

 	pinctrl_pwm3: pwm3grp {
 		fsl,pins = <MX8MM_IOMUXC_GPIO1_IO14_PWM3_OUT		0x14>;
 	};

 	pinctrl_pwm4: pwm4grp {
 		fsl,pins = <MX8MM_IOMUXC_GPIO1_IO15_PWM4_OUT		0x14>;
 	};

 	pinctrl_sai3: sai3grp {
 		fsl,pins = <MX8MM_IOMUXC_SAI3_MCLK_SAI3_MCLK		0x94>,
 			   <MX8MM_IOMUXC_SAI3_RXC_SAI3_RX_BCLK		0x94>,
 			   <MX8MM_IOMUXC_SAI3_RXFS_SAI3_RX_SYNC		0x94>,
 			   <MX8MM_IOMUXC_SAI3_RXD_SAI3_RX_DATA0		0x94>,
 			   <MX8MM_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC		0x94>,
 			   <MX8MM_IOMUXC_SAI3_TXD_SAI3_TX_DATA0		0x94>,
 			   <MX8MM_IOMUXC_SAI3_TXC_SAI3_TX_BCLK		0x94>;
 	};

 	pinctrl_uart1: uart1grp {
 		fsl,pins = <MX8MM_IOMUXC_UART1_RXD_UART1_DCE_RX		0x16>,
 			   <MX8MM_IOMUXC_UART1_TXD_UART1_DCE_TX		0x16>;
 	};

 	pinctrl_uart2: uart2grp {
 		fsl,pins = <MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX		0x16>,
 			   <MX8MM_IOMUXC_UART2_TXD_UART2_DCE_TX		0x16>;
 	};

 	pinctrl_uart3: uart3grp {
 		fsl,pins = <MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX		0x16>,
 			   <MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX		0x16>;
 	};

 	pinctrl_uart4: uart4grp {
 		fsl,pins = <MX8MM_IOMUXC_UART4_RXD_UART4_DCE_RX		0x16>,
 			   <MX8MM_IOMUXC_UART4_TXD_UART4_DCE_TX		0x16>;
 	};

 	pinctrl_usbotg1: usbotg1grp {
 		fsl,pins = <MX8MM_IOMUXC_GPIO1_IO12_USB1_OTG_PWR	0x84>,
 			   <MX8MM_IOMUXC_GPIO1_IO13_USB1_OTG_OC		0x84>;
 	};

 	pinctrl_usb1_connector: usb1-connectorgrp {
 		fsl,pins = <MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10		0x1c0>;
 	};

 	pinctrl_usdhc2_gpio: usdhc2grpgpiogrp {
 		fsl,pins = <MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x84>;
 	};

 	pinctrl_usdhc2: usdhc2grp {
 		fsl,pins = <MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK		0x1d4>,
 			   <MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD		0x1d4>,
 			   <MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d4>,
 			   <MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d4>,
 			   <MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d4>,
 			   <MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d4>,
 			   <MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT	0x84>;
 	};

 	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
 		fsl,pins = <MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK		0x1d4>,
 			   <MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD		0x1d4>,
 			   <MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d4>,
 			   <MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d4>,
 			   <MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d4>,
 			   <MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d4>,
 			   <MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT	0x84>;
 	};

 	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
 		fsl,pins = <MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK		0x1d4>,
 			   <MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD		0x1d4>,
 			   <MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d4>,
 			   <MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d4>,
 			   <MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d4>,
 			   <MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d4>,
 			   <MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT	0x84>;
 	};
 };
	// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
	/*
	* Copyright 2020-2021 TQ-Systems GmbH
	*/

	/dts-v1/;

	#include "imx8mm-tqma8mqml.dtsi"
	#include "mba8mx.dtsi"

	/ {
	model = "TQ-Systems GmbH i.MX8MM TQMa8MxML on MBa8Mx";
	compatible = "tq,imx8mm-tqma8mqml-mba8mx", "tq,imx8mm-tqma8mqml", "fsl,imx8mm";
	chassis-type = "embedded";

	aliases {
	eeprom0 = &eeprom3;
	mmc0 = &usdhc3;
	mmc1 = &usdhc2;
	mmc2 = &usdhc1;
	rtc0 = &pcf85063;
	rtc1 = &snvs_rtc;
	};

	reg_usdhc2_vmmc: regulator-vmmc {
	compatible = "regulator-fixed";
	pinctrl-names = "default";
	pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
	regulator-name = "VSD_3V3";
	regulator-min-microvolt = <3300000>;
	regulator-max-microvolt = <3300000>;
	gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
	enable-active-high;
	startup-delay-us = <100>;
	off-on-delay-us = <12000>;
	};

	connector {
	compatible = "gpio-usb-b-connector", "usb-b-connector";
	type = "micro";
	label = "X19";
	pinctrl-names = "default";
	pinctrl-0 = <&pinctrl_usb1_connector>;
	id-gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;

	ports {
	#address-cells = <1>;
	#size-cells = <0>;

	port@0 {
	reg = <0>;
	usb_dr_connector: endpoint {
	remote-endpoint = <&usb1_drd_sw>;
	};
	};
	};
	};
	};

	&i2c1 {
	expander2: gpio@27 {
	compatible = "nxp,pca9555";
	reg = <0x27>;
	gpio-controller;
	#gpio-cells = <2>;
	vcc-supply = <&reg_vcc_3v3>;
	pinctrl-names = "default";
	pinctrl-0 = <&pinctrl_expander>;
	interrupt-parent = <&gpio1>;
	interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
	interrupt-controller;
	#interrupt-cells = <2>;
	};
	};

	&pcie_phy {
	clocks = <&pcie0_refclk>;
	status = "okay";
	};

	&pcie0 {
	reset-gpio = <&expander0 14 GPIO_ACTIVE_LOW>;
	clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, <&pcie0_refclk>,
	<&clk IMX8MM_CLK_PCIE1_AUX>;
	assigned-clocks = <&clk IMX8MM_CLK_PCIE1_AUX>,
	<&clk IMX8MM_CLK_PCIE1_CTRL>;
	assigned-clock-rates = <10000000>, <250000000>;
	assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_50M>,
	<&clk IMX8MM_SYS_PLL2_250M>;
	status = "okay";
	};

	&sai3 {
	assigned-clocks = <&clk IMX8MM_CLK_SAI3>;
	assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>;
	clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3", "pll8k", "pll11k";
	clocks = <&clk IMX8MM_CLK_SAI3_IPG>, <&clk IMX8MM_CLK_DUMMY>,
	<&clk IMX8MM_CLK_SAI3_ROOT>, <&clk IMX8MM_CLK_DUMMY>,
	<&clk IMX8MM_CLK_DUMMY>, <&clk IMX8MM_AUDIO_PLL1_OUT>,
	<&clk IMX8MM_AUDIO_PLL2_OUT>;
	};

	&tlv320aic3x04 {
	clock-names = "mclk";
	clocks = <&clk IMX8MM_CLK_SAI3_ROOT>;
	};

	&uart1 {
	assigned-clocks = <&clk IMX8MM_CLK_UART1>;
	assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
	};

	&uart2 {
	assigned-clocks = <&clk IMX8MM_CLK_UART2>;
	assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
	};

	&usbotg1 {
	pinctrl-names = "default";
	pinctrl-0 = <&pinctrl_usbotg1>;
	dr_mode = "otg";
	srp-disable;
	hnp-disable;
	adp-disable;
	power-active-high;
	over-current-active-low;
	usb-role-switch;
	status = "okay";

	port {
	usb1_drd_sw: endpoint {
	remote-endpoint = <&usb_dr_connector>;
	};
	};
	};

	&usbotg2 {
	dr_mode = "host";
	disable-over-current;
	vbus-supply = <&reg_hub_vbus>;
	status = "okay";
	};

	&iomuxc {
	pinctrl_ecspi1: ecspi1grp {
	fsl,pins = <MX8MM_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK 0x00000006>,
	<MX8MM_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI 0x00000006>,
	<MX8MM_IOMUXC_ECSPI1_MISO_ECSPI1_MISO 0x00000006>,
	<MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9 0x00000006>;
	};

	pinctrl_ecspi2: ecspi2grp {
	fsl,pins = <MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0x00000006>,
	<MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI 0x00000006>,
	<MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO 0x00000006>,
	<MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13 0x00000006>;
	};

	pinctrl_expander: expandergrp {
	fsl,pins = <MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x94>;
	};

	pinctrl_fec1: fec1grp {
	fsl,pins = <MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x40000002>,
	<MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x40000002>,
	<MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x14>,
	<MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x14>,
	<MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x14>,
	<MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x14>,
	<MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x90>,
	<MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x90>,
	<MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x90>,
	<MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x90>,
	<MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x14>,
	<MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x90>,
	<MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x90>,
	<MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x14>;
	};

	pinctrl_gpiobutton: gpiobuttongrp {
	fsl,pins = <MX8MM_IOMUXC_GPIO1_IO05_GPIO1_IO5 0x84>,
	<MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x84>,
	<MX8MM_IOMUXC_SD1_CLK_GPIO2_IO0 0x84>;
	};

	pinctrl_gpioled: gpioledgrp {
	fsl,pins = <MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0 0x84>,
	<MX8MM_IOMUXC_NAND_DQS_GPIO3_IO14 0x84>;
	};

	pinctrl_i2c2: i2c2grp {
	fsl,pins = <MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL 0x40000004>,
	<MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA 0x40000004>;
	};

	pinctrl_i2c2_gpio: i2c2gpiogrp {
	fsl,pins = <MX8MM_IOMUXC_I2C2_SCL_GPIO5_IO16 0x40000004>,
	<MX8MM_IOMUXC_I2C2_SDA_GPIO5_IO17 0x40000004>;
	};

	pinctrl_i2c3: i2c3grp {
	fsl,pins = <MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL 0x40000004>,
	<MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x40000004>;
	};

	pinctrl_i2c3_gpio: i2c3gpiogrp {
	fsl,pins = <MX8MM_IOMUXC_I2C3_SCL_GPIO5_IO18 0x40000004>,
	<MX8MM_IOMUXC_I2C3_SDA_GPIO5_IO19 0x40000004>;
	};

	pinctrl_pwm3: pwm3grp {
	fsl,pins = <MX8MM_IOMUXC_GPIO1_IO14_PWM3_OUT 0x14>;
	};

	pinctrl_pwm4: pwm4grp {
	fsl,pins = <MX8MM_IOMUXC_GPIO1_IO15_PWM4_OUT 0x14>;
	};

	pinctrl_sai3: sai3grp {
	fsl,pins = <MX8MM_IOMUXC_SAI3_MCLK_SAI3_MCLK 0x94>,
	<MX8MM_IOMUXC_SAI3_RXC_SAI3_RX_BCLK 0x94>,
	<MX8MM_IOMUXC_SAI3_RXFS_SAI3_RX_SYNC 0x94>,
	<MX8MM_IOMUXC_SAI3_RXD_SAI3_RX_DATA0 0x94>,
	<MX8MM_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC 0x94>,
	<MX8MM_IOMUXC_SAI3_TXD_SAI3_TX_DATA0 0x94>,
	<MX8MM_IOMUXC_SAI3_TXC_SAI3_TX_BCLK 0x94>;
	};

	pinctrl_uart1: uart1grp {
	fsl,pins = <MX8MM_IOMUXC_UART1_RXD_UART1_DCE_RX 0x16>,
	<MX8MM_IOMUXC_UART1_TXD_UART1_DCE_TX 0x16>;
	};

	pinctrl_uart2: uart2grp {
	fsl,pins = <MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX 0x16>,
	<MX8MM_IOMUXC_UART2_TXD_UART2_DCE_TX 0x16>;
	};

	pinctrl_uart3: uart3grp {
	fsl,pins = <MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX 0x16>,
	<MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX 0x16>;
	};

	pinctrl_uart4: uart4grp {
	fsl,pins = <MX8MM_IOMUXC_UART4_RXD_UART4_DCE_RX 0x16>,
	<MX8MM_IOMUXC_UART4_TXD_UART4_DCE_TX 0x16>;
	};

	pinctrl_usbotg1: usbotg1grp {
	fsl,pins = <MX8MM_IOMUXC_GPIO1_IO12_USB1_OTG_PWR 0x84>,
	<MX8MM_IOMUXC_GPIO1_IO13_USB1_OTG_OC 0x84>;
	};

	pinctrl_usb1_connector: usb1-connectorgrp {
	fsl,pins = <MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10 0x1c0>;
	};

	pinctrl_usdhc2_gpio: usdhc2grpgpiogrp {
	fsl,pins = <MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x84>;
	};

	pinctrl_usdhc2: usdhc2grp {
	fsl,pins = <MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x1d4>,
	<MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4>,
	<MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4>,
	<MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4>,
	<MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4>,
	<MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4>,
	<MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x84>;
	};

	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
	fsl,pins = <MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x1d4>,
	<MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4>,
	<MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4>,
	<MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4>,
	<MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4>,
	<MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4>,
	<MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x84>;
	};

	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
	fsl,pins = <MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x1d4>,
	<MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4>,
	<MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4>,
	<MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4>,
	<MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4>,
	<MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4>,
	<MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x84>;
	};
	};