| // SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| /* |
| * Device Tree file for CZ.NIC Turris Mox Board |
| * 2019 by Marek Behún <kabel@kernel.org> |
| */ |
| |
| /dts-v1/; |
| |
| #include <dt-bindings/bus/moxtet.h> |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/input/input.h> |
| #include "armada-372x.dtsi" |
| |
| / { |
| model = "CZ.NIC Turris Mox Board"; |
| compatible = "cznic,turris-mox", "marvell,armada3720", |
| "marvell,armada3700"; |
| |
| aliases { |
| spi0 = &spi0; |
| ethernet0 = ð0; |
| ethernet1 = ð1; |
| mmc0 = &sdhci0; |
| mmc1 = &sdhci1; |
| }; |
| |
| chosen { |
| stdout-path = "serial0:115200n8"; |
| }; |
| |
| memory@0 { |
| device_type = "memory"; |
| reg = <0x00000000 0x00000000 0x00000000 0x20000000>; |
| }; |
| |
| leds { |
| compatible = "gpio-leds"; |
| led { |
| label = "mox:red:activity"; |
| gpios = <&gpiosb 21 GPIO_ACTIVE_LOW>; |
| linux,default-trigger = "default-on"; |
| }; |
| }; |
| |
| gpio-keys { |
| compatible = "gpio-keys"; |
| |
| key-reset { |
| label = "reset"; |
| linux,code = <KEY_RESTART>; |
| gpios = <&gpiosb 20 GPIO_ACTIVE_LOW>; |
| debounce-interval = <60>; |
| }; |
| }; |
| |
| exp_usb3_vbus: usb3-vbus { |
| compatible = "regulator-fixed"; |
| regulator-name = "usb3-vbus"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| enable-active-high; |
| regulator-always-on; |
| gpio = <&gpiosb 0 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| vsdc_reg: vsdc-reg { |
| compatible = "regulator-gpio"; |
| regulator-name = "vsdc"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-boot-on; |
| |
| gpios = <&gpiosb 23 GPIO_ACTIVE_HIGH>; |
| gpios-states = <0>; |
| states = <1800000 0x1 |
| 3300000 0x0>; |
| enable-active-high; |
| }; |
| |
| vsdio_reg: vsdio-reg { |
| compatible = "regulator-gpio"; |
| regulator-name = "vsdio"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-boot-on; |
| |
| gpios = <&gpiosb 22 GPIO_ACTIVE_HIGH>; |
| gpios-states = <0>; |
| states = <1800000 0x1 |
| 3300000 0x0>; |
| enable-active-high; |
| }; |
| |
| sdhci1_pwrseq: sdhci1-pwrseq { |
| compatible = "mmc-pwrseq-simple"; |
| reset-gpios = <&gpionb 19 GPIO_ACTIVE_HIGH>; |
| status = "okay"; |
| }; |
| |
| sfp: sfp { |
| compatible = "sff,sfp"; |
| i2c-bus = <&i2c0>; |
| los-gpios = <&moxtet_sfp 0 GPIO_ACTIVE_HIGH>; |
| tx-fault-gpios = <&moxtet_sfp 1 GPIO_ACTIVE_HIGH>; |
| mod-def0-gpios = <&moxtet_sfp 2 GPIO_ACTIVE_LOW>; |
| tx-disable-gpios = <&moxtet_sfp 4 GPIO_ACTIVE_HIGH>; |
| rate-select0-gpios = <&moxtet_sfp 5 GPIO_ACTIVE_HIGH>; |
| maximum-power-milliwatt = <3000>; |
| |
| /* enabled by U-Boot if SFP module is present */ |
| status = "disabled"; |
| }; |
| |
| firmware { |
| armada-3700-rwtm { |
| compatible = "marvell,armada-3700-rwtm-firmware", "cznic,turris-mox-rwtm"; |
| }; |
| }; |
| }; |
| |
| &i2c0 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c1_pins>; |
| clock-frequency = <100000>; |
| /delete-property/ mrvl,i2c-fast-mode; |
| status = "okay"; |
| |
| /* MCP7940MT-I/MNY RTC */ |
| rtc@6f { |
| compatible = "microchip,mcp7940x"; |
| reg = <0x6f>; |
| interrupt-parent = <&gpiosb>; |
| interrupts = <5 IRQ_TYPE_EDGE_FALLING>; /* GPIO2_5 */ |
| }; |
| }; |
| |
| &pcie0 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pcie_reset_pins &pcie_clkreq_pins>; |
| status = "okay"; |
| reset-gpios = <&gpiosb 3 GPIO_ACTIVE_LOW>; |
| slot-power-limit-milliwatt = <10000>; |
| /* |
| * U-Boot port for Turris Mox has a bug which always expects that "ranges" DT property |
| * contains exactly 2 ranges with 3 (child) address cells, 2 (parent) address cells and |
| * 2 size cells and also expects that the second range starts at 16 MB offset. Also it |
| * expects that first range uses same address for PCI (child) and CPU (parent) cells (so |
| * no remapping) and that this address is the lowest from all specified ranges. If these |
| * conditions are not met then U-Boot crashes during loading kernel DTB file. PCIe address |
| * space is 128 MB long, so the best split between MEM and IO is to use fixed 16 MB window |
| * for IO and the rest 112 MB (64+32+16) for MEM, despite that maximal IO size is just 64 kB. |
| * This bug is not present in U-Boot ports for other Armada 3700 devices and is fixed in |
| * U-Boot version 2021.07. See relevant U-Boot commits (the last one contains fix): |
| * https://source.denx.de/u-boot/u-boot/-/commit/cb2ddb291ee6fcbddd6d8f4ff49089dfe580f5d7 |
| * https://source.denx.de/u-boot/u-boot/-/commit/c64ac3b3185aeb3846297ad7391fc6df8ecd73bf |
| * https://source.denx.de/u-boot/u-boot/-/commit/4a82fca8e330157081fc132a591ebd99ba02ee33 |
| * Bug related to requirement of same child and parent addresses for first range is fixed |
| * in U-Boot version 2022.04 by following commit: |
| * https://source.denx.de/u-boot/u-boot/-/commit/1fd54253bca7d43d046bba4853fe5fafd034bc17 |
| */ |
| #address-cells = <3>; |
| #size-cells = <2>; |
| ranges = <0x81000000 0 0xe8000000 0 0xe8000000 0 0x01000000 /* Port 0 IO */ |
| 0x82000000 0 0xe9000000 0 0xe9000000 0 0x07000000>; /* Port 0 MEM */ |
| |
| /* enabled by U-Boot if PCIe module is present */ |
| status = "disabled"; |
| }; |
| |
| &uart0 { |
| status = "okay"; |
| }; |
| |
| ð0 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&rgmii_pins>; |
| phy-mode = "rgmii-id"; |
| phy-handle = <&phy1>; |
| status = "okay"; |
| }; |
| |
| ð1 { |
| phy-mode = "2500base-x"; |
| managed = "in-band-status"; |
| phys = <&comphy0 1>; |
| }; |
| |
| &sdhci0 { |
| wp-inverted; |
| bus-width = <4>; |
| cd-gpios = <&gpionb 10 GPIO_ACTIVE_HIGH>; |
| vqmmc-supply = <&vsdc_reg>; |
| marvell,pad-type = "sd"; |
| status = "okay"; |
| }; |
| |
| &sdhci1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&sdio_pins>; |
| non-removable; |
| bus-width = <4>; |
| marvell,pad-type = "sd"; |
| vqmmc-supply = <&vsdio_reg>; |
| mmc-pwrseq = <&sdhci1_pwrseq>; |
| /* forbid SDR104 for FCC purposes */ |
| sdhci-caps-mask = <0x2 0x0>; |
| status = "okay"; |
| }; |
| |
| &spi0 { |
| status = "okay"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&spi_quad_pins &spi_cs1_pins>; |
| assigned-clocks = <&nb_periph_clk 7>; |
| assigned-clock-parents = <&tbg 1>; |
| assigned-clock-rates = <20000000>; |
| |
| flash@0 { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| compatible = "jedec,spi-nor"; |
| reg = <0>; |
| spi-max-frequency = <20000000>; |
| |
| partitions { |
| compatible = "fixed-partitions"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| partition@0 { |
| label = "secure-firmware"; |
| reg = <0x0 0x20000>; |
| }; |
| |
| partition@20000 { |
| label = "a53-firmware"; |
| reg = <0x20000 0x160000>; |
| }; |
| |
| partition@180000 { |
| label = "u-boot-env"; |
| reg = <0x180000 0x10000>; |
| }; |
| |
| partition@190000 { |
| label = "Rescue system"; |
| reg = <0x190000 0x660000>; |
| }; |
| |
| partition@7f0000 { |
| label = "dtb"; |
| reg = <0x7f0000 0x10000>; |
| }; |
| }; |
| }; |
| |
| moxtet: moxtet@1 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "cznic,moxtet"; |
| reg = <1>; |
| reset-gpios = <&gpiosb 2 GPIO_ACTIVE_LOW>; |
| spi-max-frequency = <10000000>; |
| spi-cpol; |
| spi-cpha; |
| interrupt-controller; |
| #interrupt-cells = <1>; |
| interrupt-parent = <&gpiosb>; |
| interrupts = <5 IRQ_TYPE_EDGE_FALLING>; |
| status = "okay"; |
| |
| moxtet_sfp: gpio@0 { |
| compatible = "cznic,moxtet-gpio"; |
| gpio-controller; |
| #gpio-cells = <2>; |
| reg = <0>; |
| status = "disabled"; |
| }; |
| }; |
| }; |
| |
| &usb2 { |
| status = "okay"; |
| }; |
| |
| &comphy2 { |
| connector { |
| compatible = "usb-a-connector"; |
| phy-supply = <&exp_usb3_vbus>; |
| }; |
| }; |
| |
| &usb3 { |
| status = "okay"; |
| phys = <&comphy2 0>; |
| }; |
| |
| &mdio { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&smi_pins>; |
| status = "okay"; |
| |
| phy1: ethernet-phy@1 { |
| reg = <1>; |
| }; |
| |
| /* |
| * NOTE: switch nodes are enabled by U-Boot if modules are present |
| * DO NOT change this node name (switch0@10) even if it is not following |
| * conventions! Deployed U-Boot binaries are explicitly looking for |
| * this node in order to augment the device tree! |
| * Also do not touch the "ports" or "port@n" nodes. These are also ABI. |
| */ |
| switch0@10 { |
| compatible = "marvell,turris-mox-mv88e6190", "marvell,mv88e6190"; |
| reg = <0x10>; |
| dsa,member = <0 0>; |
| interrupt-parent = <&moxtet>; |
| interrupts = <MOXTET_IRQ_PERIDOT(0)>; |
| status = "disabled"; |
| |
| mdio { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| switch0phy1: ethernet-phy@1 { |
| reg = <0x1>; |
| }; |
| |
| switch0phy2: ethernet-phy@2 { |
| reg = <0x2>; |
| }; |
| |
| switch0phy3: ethernet-phy@3 { |
| reg = <0x3>; |
| }; |
| |
| switch0phy4: ethernet-phy@4 { |
| reg = <0x4>; |
| }; |
| |
| switch0phy5: ethernet-phy@5 { |
| reg = <0x5>; |
| }; |
| |
| switch0phy6: ethernet-phy@6 { |
| reg = <0x6>; |
| }; |
| |
| switch0phy7: ethernet-phy@7 { |
| reg = <0x7>; |
| }; |
| |
| switch0phy8: ethernet-phy@8 { |
| reg = <0x8>; |
| }; |
| }; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@1 { |
| reg = <0x1>; |
| label = "lan1"; |
| phy-handle = <&switch0phy1>; |
| }; |
| |
| port@2 { |
| reg = <0x2>; |
| label = "lan2"; |
| phy-handle = <&switch0phy2>; |
| }; |
| |
| port@3 { |
| reg = <0x3>; |
| label = "lan3"; |
| phy-handle = <&switch0phy3>; |
| }; |
| |
| port@4 { |
| reg = <0x4>; |
| label = "lan4"; |
| phy-handle = <&switch0phy4>; |
| }; |
| |
| port@5 { |
| reg = <0x5>; |
| label = "lan5"; |
| phy-handle = <&switch0phy5>; |
| }; |
| |
| port@6 { |
| reg = <0x6>; |
| label = "lan6"; |
| phy-handle = <&switch0phy6>; |
| }; |
| |
| port@7 { |
| reg = <0x7>; |
| label = "lan7"; |
| phy-handle = <&switch0phy7>; |
| }; |
| |
| port@8 { |
| reg = <0x8>; |
| label = "lan8"; |
| phy-handle = <&switch0phy8>; |
| }; |
| |
| port@9 { |
| reg = <0x9>; |
| label = "cpu"; |
| ethernet = <ð1>; |
| phy-mode = "2500base-x"; |
| managed = "in-band-status"; |
| }; |
| |
| switch0port10: port@a { |
| reg = <0xa>; |
| label = "dsa"; |
| phy-mode = "2500base-x"; |
| managed = "in-band-status"; |
| link = <&switch1port9 &switch2port9>; |
| status = "disabled"; |
| }; |
| |
| port-sfp@a { |
| reg = <0xa>; |
| label = "sfp"; |
| sfp = <&sfp>; |
| phy-mode = "sgmii"; |
| managed = "in-band-status"; |
| status = "disabled"; |
| }; |
| }; |
| }; |
| |
| /* NOTE: this node name is ABI, don't change it! */ |
| switch0@2 { |
| compatible = "marvell,turris-mox-mv88e6085", "marvell,mv88e6085"; |
| reg = <0x2>; |
| dsa,member = <0 0>; |
| interrupt-parent = <&moxtet>; |
| interrupts = <MOXTET_IRQ_TOPAZ>; |
| status = "disabled"; |
| |
| mdio { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| switch0phy1_topaz: ethernet-phy@11 { |
| reg = <0x11>; |
| }; |
| |
| switch0phy2_topaz: ethernet-phy@12 { |
| reg = <0x12>; |
| }; |
| |
| switch0phy3_topaz: ethernet-phy@13 { |
| reg = <0x13>; |
| }; |
| |
| switch0phy4_topaz: ethernet-phy@14 { |
| reg = <0x14>; |
| }; |
| }; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@1 { |
| reg = <0x1>; |
| label = "lan1"; |
| phy-handle = <&switch0phy1_topaz>; |
| }; |
| |
| port@2 { |
| reg = <0x2>; |
| label = "lan2"; |
| phy-handle = <&switch0phy2_topaz>; |
| }; |
| |
| port@3 { |
| reg = <0x3>; |
| label = "lan3"; |
| phy-handle = <&switch0phy3_topaz>; |
| }; |
| |
| port@4 { |
| reg = <0x4>; |
| label = "lan4"; |
| phy-handle = <&switch0phy4_topaz>; |
| }; |
| |
| port@5 { |
| reg = <0x5>; |
| label = "cpu"; |
| phy-mode = "2500base-x"; |
| managed = "in-band-status"; |
| ethernet = <ð1>; |
| }; |
| }; |
| }; |
| |
| /* NOTE: this node name is ABI, don't change it! */ |
| switch1@11 { |
| compatible = "marvell,turris-mox-mv88e6190", "marvell,mv88e6190"; |
| reg = <0x11>; |
| dsa,member = <0 1>; |
| interrupt-parent = <&moxtet>; |
| interrupts = <MOXTET_IRQ_PERIDOT(1)>; |
| status = "disabled"; |
| |
| mdio { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| switch1phy1: ethernet-phy@1 { |
| reg = <0x1>; |
| }; |
| |
| switch1phy2: ethernet-phy@2 { |
| reg = <0x2>; |
| }; |
| |
| switch1phy3: ethernet-phy@3 { |
| reg = <0x3>; |
| }; |
| |
| switch1phy4: ethernet-phy@4 { |
| reg = <0x4>; |
| }; |
| |
| switch1phy5: ethernet-phy@5 { |
| reg = <0x5>; |
| }; |
| |
| switch1phy6: ethernet-phy@6 { |
| reg = <0x6>; |
| }; |
| |
| switch1phy7: ethernet-phy@7 { |
| reg = <0x7>; |
| }; |
| |
| switch1phy8: ethernet-phy@8 { |
| reg = <0x8>; |
| }; |
| }; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@1 { |
| reg = <0x1>; |
| label = "lan9"; |
| phy-handle = <&switch1phy1>; |
| }; |
| |
| port@2 { |
| reg = <0x2>; |
| label = "lan10"; |
| phy-handle = <&switch1phy2>; |
| }; |
| |
| port@3 { |
| reg = <0x3>; |
| label = "lan11"; |
| phy-handle = <&switch1phy3>; |
| }; |
| |
| port@4 { |
| reg = <0x4>; |
| label = "lan12"; |
| phy-handle = <&switch1phy4>; |
| }; |
| |
| port@5 { |
| reg = <0x5>; |
| label = "lan13"; |
| phy-handle = <&switch1phy5>; |
| }; |
| |
| port@6 { |
| reg = <0x6>; |
| label = "lan14"; |
| phy-handle = <&switch1phy6>; |
| }; |
| |
| port@7 { |
| reg = <0x7>; |
| label = "lan15"; |
| phy-handle = <&switch1phy7>; |
| }; |
| |
| port@8 { |
| reg = <0x8>; |
| label = "lan16"; |
| phy-handle = <&switch1phy8>; |
| }; |
| |
| switch1port9: port@9 { |
| reg = <0x9>; |
| label = "dsa"; |
| phy-mode = "2500base-x"; |
| managed = "in-band-status"; |
| link = <&switch0port10>; |
| }; |
| |
| switch1port10: port@a { |
| reg = <0xa>; |
| label = "dsa"; |
| phy-mode = "2500base-x"; |
| managed = "in-band-status"; |
| link = <&switch2port9>; |
| status = "disabled"; |
| }; |
| |
| port-sfp@a { |
| reg = <0xa>; |
| label = "sfp"; |
| sfp = <&sfp>; |
| phy-mode = "sgmii"; |
| managed = "in-band-status"; |
| status = "disabled"; |
| }; |
| }; |
| }; |
| |
| /* NOTE: this node name is ABI, don't change it! */ |
| switch1@2 { |
| compatible = "marvell,turris-mox-mv88e6085", "marvell,mv88e6085"; |
| reg = <0x2>; |
| dsa,member = <0 1>; |
| interrupt-parent = <&moxtet>; |
| interrupts = <MOXTET_IRQ_TOPAZ>; |
| status = "disabled"; |
| |
| mdio { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| switch1phy1_topaz: ethernet-phy@11 { |
| reg = <0x11>; |
| }; |
| |
| switch1phy2_topaz: ethernet-phy@12 { |
| reg = <0x12>; |
| }; |
| |
| switch1phy3_topaz: ethernet-phy@13 { |
| reg = <0x13>; |
| }; |
| |
| switch1phy4_topaz: ethernet-phy@14 { |
| reg = <0x14>; |
| }; |
| }; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@1 { |
| reg = <0x1>; |
| label = "lan9"; |
| phy-handle = <&switch1phy1_topaz>; |
| }; |
| |
| port@2 { |
| reg = <0x2>; |
| label = "lan10"; |
| phy-handle = <&switch1phy2_topaz>; |
| }; |
| |
| port@3 { |
| reg = <0x3>; |
| label = "lan11"; |
| phy-handle = <&switch1phy3_topaz>; |
| }; |
| |
| port@4 { |
| reg = <0x4>; |
| label = "lan12"; |
| phy-handle = <&switch1phy4_topaz>; |
| }; |
| |
| port@5 { |
| reg = <0x5>; |
| label = "dsa"; |
| phy-mode = "2500base-x"; |
| managed = "in-band-status"; |
| link = <&switch0port10>; |
| }; |
| }; |
| }; |
| |
| /* NOTE: this node name is ABI, don't change it! */ |
| switch2@12 { |
| compatible = "marvell,turris-mox-mv88e6190", "marvell,mv88e6190"; |
| reg = <0x12>; |
| dsa,member = <0 2>; |
| interrupt-parent = <&moxtet>; |
| interrupts = <MOXTET_IRQ_PERIDOT(2)>; |
| status = "disabled"; |
| |
| mdio { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| switch2phy1: ethernet-phy@1 { |
| reg = <0x1>; |
| }; |
| |
| switch2phy2: ethernet-phy@2 { |
| reg = <0x2>; |
| }; |
| |
| switch2phy3: ethernet-phy@3 { |
| reg = <0x3>; |
| }; |
| |
| switch2phy4: ethernet-phy@4 { |
| reg = <0x4>; |
| }; |
| |
| switch2phy5: ethernet-phy@5 { |
| reg = <0x5>; |
| }; |
| |
| switch2phy6: ethernet-phy@6 { |
| reg = <0x6>; |
| }; |
| |
| switch2phy7: ethernet-phy@7 { |
| reg = <0x7>; |
| }; |
| |
| switch2phy8: ethernet-phy@8 { |
| reg = <0x8>; |
| }; |
| }; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@1 { |
| reg = <0x1>; |
| label = "lan17"; |
| phy-handle = <&switch2phy1>; |
| }; |
| |
| port@2 { |
| reg = <0x2>; |
| label = "lan18"; |
| phy-handle = <&switch2phy2>; |
| }; |
| |
| port@3 { |
| reg = <0x3>; |
| label = "lan19"; |
| phy-handle = <&switch2phy3>; |
| }; |
| |
| port@4 { |
| reg = <0x4>; |
| label = "lan20"; |
| phy-handle = <&switch2phy4>; |
| }; |
| |
| port@5 { |
| reg = <0x5>; |
| label = "lan21"; |
| phy-handle = <&switch2phy5>; |
| }; |
| |
| port@6 { |
| reg = <0x6>; |
| label = "lan22"; |
| phy-handle = <&switch2phy6>; |
| }; |
| |
| port@7 { |
| reg = <0x7>; |
| label = "lan23"; |
| phy-handle = <&switch2phy7>; |
| }; |
| |
| port@8 { |
| reg = <0x8>; |
| label = "lan24"; |
| phy-handle = <&switch2phy8>; |
| }; |
| |
| switch2port9: port@9 { |
| reg = <0x9>; |
| label = "dsa"; |
| phy-mode = "2500base-x"; |
| managed = "in-band-status"; |
| link = <&switch1port10 &switch0port10>; |
| }; |
| |
| port-sfp@a { |
| reg = <0xa>; |
| label = "sfp"; |
| sfp = <&sfp>; |
| phy-mode = "sgmii"; |
| managed = "in-band-status"; |
| status = "disabled"; |
| }; |
| }; |
| }; |
| |
| /* NOTE: this node name is ABI, don't change it! */ |
| switch2@2 { |
| compatible = "marvell,turris-mox-mv88e6085", "marvell,mv88e6085"; |
| reg = <0x2>; |
| dsa,member = <0 2>; |
| interrupt-parent = <&moxtet>; |
| interrupts = <MOXTET_IRQ_TOPAZ>; |
| status = "disabled"; |
| |
| mdio { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| switch2phy1_topaz: ethernet-phy@11 { |
| reg = <0x11>; |
| }; |
| |
| switch2phy2_topaz: ethernet-phy@12 { |
| reg = <0x12>; |
| }; |
| |
| switch2phy3_topaz: ethernet-phy@13 { |
| reg = <0x13>; |
| }; |
| |
| switch2phy4_topaz: ethernet-phy@14 { |
| reg = <0x14>; |
| }; |
| }; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@1 { |
| reg = <0x1>; |
| label = "lan17"; |
| phy-handle = <&switch2phy1_topaz>; |
| }; |
| |
| port@2 { |
| reg = <0x2>; |
| label = "lan18"; |
| phy-handle = <&switch2phy2_topaz>; |
| }; |
| |
| port@3 { |
| reg = <0x3>; |
| label = "lan19"; |
| phy-handle = <&switch2phy3_topaz>; |
| }; |
| |
| port@4 { |
| reg = <0x4>; |
| label = "lan20"; |
| phy-handle = <&switch2phy4_topaz>; |
| }; |
| |
| port@5 { |
| reg = <0x5>; |
| label = "dsa"; |
| phy-mode = "2500base-x"; |
| managed = "in-band-status"; |
| link = <&switch1port10 &switch0port10>; |
| }; |
| }; |
| }; |
| }; |
