blob: 82573dc4d8cf8ebf99d84d40056d5fb5dac85303 [file] [log] [blame]
/*
* Maxim (Dallas) MAX3107/8/9, MAX14830 serial driver
*
* Copyright (C) 2012-2014 Alexander Shiyan <shc_work@mail.ru>
*
* Based on max3100.c, by Christian Pellegrin <chripell@evolware.org>
* Based on max3110.c, by Feng Tang <feng.tang@intel.com>
* Based on max3107.c, by Aavamobile
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*/
#include <linux/bitops.h>
#include <linux/clk.h>
#include <linux/delay.h>
#include <linux/device.h>
#include <linux/gpio.h>
#include <linux/module.h>
#include <linux/of.h>
#include <linux/of_device.h>
#include <linux/regmap.h>
#include <linux/serial_core.h>
#include <linux/serial.h>
#include <linux/tty.h>
#include <linux/tty_flip.h>
#include <linux/spi/spi.h>
#include <linux/uaccess.h>
#define MAX310X_NAME "max310x"
#define MAX310X_MAJOR 204
#define MAX310X_MINOR 209
/* MAX310X register definitions */
#define MAX310X_RHR_REG (0x00) /* RX FIFO */
#define MAX310X_THR_REG (0x00) /* TX FIFO */
#define MAX310X_IRQEN_REG (0x01) /* IRQ enable */
#define MAX310X_IRQSTS_REG (0x02) /* IRQ status */
#define MAX310X_LSR_IRQEN_REG (0x03) /* LSR IRQ enable */
#define MAX310X_LSR_IRQSTS_REG (0x04) /* LSR IRQ status */
#define MAX310X_REG_05 (0x05)
#define MAX310X_SPCHR_IRQEN_REG MAX310X_REG_05 /* Special char IRQ en */
#define MAX310X_SPCHR_IRQSTS_REG (0x06) /* Special char IRQ status */
#define MAX310X_STS_IRQEN_REG (0x07) /* Status IRQ enable */
#define MAX310X_STS_IRQSTS_REG (0x08) /* Status IRQ status */
#define MAX310X_MODE1_REG (0x09) /* MODE1 */
#define MAX310X_MODE2_REG (0x0a) /* MODE2 */
#define MAX310X_LCR_REG (0x0b) /* LCR */
#define MAX310X_RXTO_REG (0x0c) /* RX timeout */
#define MAX310X_HDPIXDELAY_REG (0x0d) /* Auto transceiver delays */
#define MAX310X_IRDA_REG (0x0e) /* IRDA settings */
#define MAX310X_FLOWLVL_REG (0x0f) /* Flow control levels */
#define MAX310X_FIFOTRIGLVL_REG (0x10) /* FIFO IRQ trigger levels */
#define MAX310X_TXFIFOLVL_REG (0x11) /* TX FIFO level */
#define MAX310X_RXFIFOLVL_REG (0x12) /* RX FIFO level */
#define MAX310X_FLOWCTRL_REG (0x13) /* Flow control */
#define MAX310X_XON1_REG (0x14) /* XON1 character */
#define MAX310X_XON2_REG (0x15) /* XON2 character */
#define MAX310X_XOFF1_REG (0x16) /* XOFF1 character */
#define MAX310X_XOFF2_REG (0x17) /* XOFF2 character */
#define MAX310X_GPIOCFG_REG (0x18) /* GPIO config */
#define MAX310X_GPIODATA_REG (0x19) /* GPIO data */
#define MAX310X_PLLCFG_REG (0x1a) /* PLL config */
#define MAX310X_BRGCFG_REG (0x1b) /* Baud rate generator conf */
#define MAX310X_BRGDIVLSB_REG (0x1c) /* Baud rate divisor LSB */
#define MAX310X_BRGDIVMSB_REG (0x1d) /* Baud rate divisor MSB */
#define MAX310X_CLKSRC_REG (0x1e) /* Clock source */
#define MAX310X_REG_1F (0x1f)
#define MAX310X_REVID_REG MAX310X_REG_1F /* Revision ID */
#define MAX310X_GLOBALIRQ_REG MAX310X_REG_1F /* Global IRQ (RO) */
#define MAX310X_GLOBALCMD_REG MAX310X_REG_1F /* Global Command (WO) */
/* Extended registers */
#define MAX310X_REVID_EXTREG MAX310X_REG_05 /* Revision ID */
/* IRQ register bits */
#define MAX310X_IRQ_LSR_BIT (1 << 0) /* LSR interrupt */
#define MAX310X_IRQ_SPCHR_BIT (1 << 1) /* Special char interrupt */
#define MAX310X_IRQ_STS_BIT (1 << 2) /* Status interrupt */
#define MAX310X_IRQ_RXFIFO_BIT (1 << 3) /* RX FIFO interrupt */
#define MAX310X_IRQ_TXFIFO_BIT (1 << 4) /* TX FIFO interrupt */
#define MAX310X_IRQ_TXEMPTY_BIT (1 << 5) /* TX FIFO empty interrupt */
#define MAX310X_IRQ_RXEMPTY_BIT (1 << 6) /* RX FIFO empty interrupt */
#define MAX310X_IRQ_CTS_BIT (1 << 7) /* CTS interrupt */
/* LSR register bits */
#define MAX310X_LSR_RXTO_BIT (1 << 0) /* RX timeout */
#define MAX310X_LSR_RXOVR_BIT (1 << 1) /* RX overrun */
#define MAX310X_LSR_RXPAR_BIT (1 << 2) /* RX parity error */
#define MAX310X_LSR_FRERR_BIT (1 << 3) /* Frame error */
#define MAX310X_LSR_RXBRK_BIT (1 << 4) /* RX break */
#define MAX310X_LSR_RXNOISE_BIT (1 << 5) /* RX noise */
#define MAX310X_LSR_CTS_BIT (1 << 7) /* CTS pin state */
/* Special character register bits */
#define MAX310X_SPCHR_XON1_BIT (1 << 0) /* XON1 character */
#define MAX310X_SPCHR_XON2_BIT (1 << 1) /* XON2 character */
#define MAX310X_SPCHR_XOFF1_BIT (1 << 2) /* XOFF1 character */
#define MAX310X_SPCHR_XOFF2_BIT (1 << 3) /* XOFF2 character */
#define MAX310X_SPCHR_BREAK_BIT (1 << 4) /* RX break */
#define MAX310X_SPCHR_MULTIDROP_BIT (1 << 5) /* 9-bit multidrop addr char */
/* Status register bits */
#define MAX310X_STS_GPIO0_BIT (1 << 0) /* GPIO 0 interrupt */
#define MAX310X_STS_GPIO1_BIT (1 << 1) /* GPIO 1 interrupt */
#define MAX310X_STS_GPIO2_BIT (1 << 2) /* GPIO 2 interrupt */
#define MAX310X_STS_GPIO3_BIT (1 << 3) /* GPIO 3 interrupt */
#define MAX310X_STS_CLKREADY_BIT (1 << 5) /* Clock ready */
#define MAX310X_STS_SLEEP_BIT (1 << 6) /* Sleep interrupt */
/* MODE1 register bits */
#define MAX310X_MODE1_RXDIS_BIT (1 << 0) /* RX disable */
#define MAX310X_MODE1_TXDIS_BIT (1 << 1) /* TX disable */
#define MAX310X_MODE1_TXHIZ_BIT (1 << 2) /* TX pin three-state */
#define MAX310X_MODE1_RTSHIZ_BIT (1 << 3) /* RTS pin three-state */
#define MAX310X_MODE1_TRNSCVCTRL_BIT (1 << 4) /* Transceiver ctrl enable */
#define MAX310X_MODE1_FORCESLEEP_BIT (1 << 5) /* Force sleep mode */
#define MAX310X_MODE1_AUTOSLEEP_BIT (1 << 6) /* Auto sleep enable */
#define MAX310X_MODE1_IRQSEL_BIT (1 << 7) /* IRQ pin enable */
/* MODE2 register bits */
#define MAX310X_MODE2_RST_BIT (1 << 0) /* Chip reset */
#define MAX310X_MODE2_FIFORST_BIT (1 << 1) /* FIFO reset */
#define MAX310X_MODE2_RXTRIGINV_BIT (1 << 2) /* RX FIFO INT invert */
#define MAX310X_MODE2_RXEMPTINV_BIT (1 << 3) /* RX FIFO empty INT invert */
#define MAX310X_MODE2_SPCHR_BIT (1 << 4) /* Special chr detect enable */
#define MAX310X_MODE2_LOOPBACK_BIT (1 << 5) /* Internal loopback enable */
#define MAX310X_MODE2_MULTIDROP_BIT (1 << 6) /* 9-bit multidrop enable */
#define MAX310X_MODE2_ECHOSUPR_BIT (1 << 7) /* ECHO suppression enable */
/* LCR register bits */
#define MAX310X_LCR_LENGTH0_BIT (1 << 0) /* Word length bit 0 */
#define MAX310X_LCR_LENGTH1_BIT (1 << 1) /* Word length bit 1
*
* Word length bits table:
* 00 -> 5 bit words
* 01 -> 6 bit words
* 10 -> 7 bit words
* 11 -> 8 bit words
*/
#define MAX310X_LCR_STOPLEN_BIT (1 << 2) /* STOP length bit
*
* STOP length bit table:
* 0 -> 1 stop bit
* 1 -> 1-1.5 stop bits if
* word length is 5,
* 2 stop bits otherwise
*/
#define MAX310X_LCR_PARITY_BIT (1 << 3) /* Parity bit enable */
#define MAX310X_LCR_EVENPARITY_BIT (1 << 4) /* Even parity bit enable */
#define MAX310X_LCR_FORCEPARITY_BIT (1 << 5) /* 9-bit multidrop parity */
#define MAX310X_LCR_TXBREAK_BIT (1 << 6) /* TX break enable */
#define MAX310X_LCR_RTS_BIT (1 << 7) /* RTS pin control */
#define MAX310X_LCR_WORD_LEN_5 (0x00)
#define MAX310X_LCR_WORD_LEN_6 (0x01)
#define MAX310X_LCR_WORD_LEN_7 (0x02)
#define MAX310X_LCR_WORD_LEN_8 (0x03)
/* IRDA register bits */
#define MAX310X_IRDA_IRDAEN_BIT (1 << 0) /* IRDA mode enable */
#define MAX310X_IRDA_SIR_BIT (1 << 1) /* SIR mode enable */
/* Flow control trigger level register masks */
#define MAX310X_FLOWLVL_HALT_MASK (0x000f) /* Flow control halt level */
#define MAX310X_FLOWLVL_RES_MASK (0x00f0) /* Flow control resume level */
#define MAX310X_FLOWLVL_HALT(words) ((words / 8) & 0x0f)
#define MAX310X_FLOWLVL_RES(words) (((words / 8) & 0x0f) << 4)
/* FIFO interrupt trigger level register masks */
#define MAX310X_FIFOTRIGLVL_TX_MASK (0x0f) /* TX FIFO trigger level */
#define MAX310X_FIFOTRIGLVL_RX_MASK (0xf0) /* RX FIFO trigger level */
#define MAX310X_FIFOTRIGLVL_TX(words) ((words / 8) & 0x0f)
#define MAX310X_FIFOTRIGLVL_RX(words) (((words / 8) & 0x0f) << 4)
/* Flow control register bits */
#define MAX310X_FLOWCTRL_AUTORTS_BIT (1 << 0) /* Auto RTS flow ctrl enable */
#define MAX310X_FLOWCTRL_AUTOCTS_BIT (1 << 1) /* Auto CTS flow ctrl enable */
#define MAX310X_FLOWCTRL_GPIADDR_BIT (1 << 2) /* Enables that GPIO inputs
* are used in conjunction with
* XOFF2 for definition of
* special character */
#define MAX310X_FLOWCTRL_SWFLOWEN_BIT (1 << 3) /* Auto SW flow ctrl enable */
#define MAX310X_FLOWCTRL_SWFLOW0_BIT (1 << 4) /* SWFLOW bit 0 */
#define MAX310X_FLOWCTRL_SWFLOW1_BIT (1 << 5) /* SWFLOW bit 1
*
* SWFLOW bits 1 & 0 table:
* 00 -> no transmitter flow
* control
* 01 -> receiver compares
* XON2 and XOFF2
* and controls
* transmitter
* 10 -> receiver compares
* XON1 and XOFF1
* and controls
* transmitter
* 11 -> receiver compares
* XON1, XON2, XOFF1 and
* XOFF2 and controls
* transmitter
*/
#define MAX310X_FLOWCTRL_SWFLOW2_BIT (1 << 6) /* SWFLOW bit 2 */
#define MAX310X_FLOWCTRL_SWFLOW3_BIT (1 << 7) /* SWFLOW bit 3
*
* SWFLOW bits 3 & 2 table:
* 00 -> no received flow
* control
* 01 -> transmitter generates
* XON2 and XOFF2
* 10 -> transmitter generates
* XON1 and XOFF1
* 11 -> transmitter generates
* XON1, XON2, XOFF1 and
* XOFF2
*/
/* PLL configuration register masks */
#define MAX310X_PLLCFG_PREDIV_MASK (0x3f) /* PLL predivision value */
#define MAX310X_PLLCFG_PLLFACTOR_MASK (0xc0) /* PLL multiplication factor */
/* Baud rate generator configuration register bits */
#define MAX310X_BRGCFG_2XMODE_BIT (1 << 4) /* Double baud rate */
#define MAX310X_BRGCFG_4XMODE_BIT (1 << 5) /* Quadruple baud rate */
/* Clock source register bits */
#define MAX310X_CLKSRC_CRYST_BIT (1 << 1) /* Crystal osc enable */
#define MAX310X_CLKSRC_PLL_BIT (1 << 2) /* PLL enable */
#define MAX310X_CLKSRC_PLLBYP_BIT (1 << 3) /* PLL bypass */
#define MAX310X_CLKSRC_EXTCLK_BIT (1 << 4) /* External clock enable */
#define MAX310X_CLKSRC_CLK2RTS_BIT (1 << 7) /* Baud clk to RTS pin */
/* Global commands */
#define MAX310X_EXTREG_ENBL (0xce)
#define MAX310X_EXTREG_DSBL (0xcd)
/* Misc definitions */
#define MAX310X_FIFO_SIZE (128)
#define MAX310x_REV_MASK (0xfc)
/* MAX3107 specific */
#define MAX3107_REV_ID (0xa0)
/* MAX3109 specific */
#define MAX3109_REV_ID (0xc0)
/* MAX14830 specific */
#define MAX14830_BRGCFG_CLKDIS_BIT (1 << 6) /* Clock Disable */
#define MAX14830_REV_ID (0xb0)
struct max310x_devtype {
char name[9];
int nr;
int (*detect)(struct device *);
void (*power)(struct uart_port *, int);
};
struct max310x_one {
struct uart_port port;
struct work_struct tx_work;
struct work_struct md_work;
};
struct max310x_port {
struct uart_driver uart;
struct max310x_devtype *devtype;
struct regmap *regmap;
struct mutex mutex;
struct clk *clk;
#ifdef CONFIG_GPIOLIB
struct gpio_chip gpio;
#endif
struct max310x_one p[0];
};
static u8 max310x_port_read(struct uart_port *port, u8 reg)
{
struct max310x_port *s = dev_get_drvdata(port->dev);
unsigned int val = 0;
regmap_read(s->regmap, port->iobase + reg, &val);
return val;
}
static void max310x_port_write(struct uart_port *port, u8 reg, u8 val)
{
struct max310x_port *s = dev_get_drvdata(port->dev);
regmap_write(s->regmap, port->iobase + reg, val);
}
static void max310x_port_update(struct uart_port *port, u8 reg, u8 mask, u8 val)
{
struct max310x_port *s = dev_get_drvdata(port->dev);
regmap_update_bits(s->regmap, port->iobase + reg, mask, val);
}
static int max3107_detect(struct device *dev)
{
struct max310x_port *s = dev_get_drvdata(dev);
unsigned int val = 0;
int ret;
ret = regmap_read(s->regmap, MAX310X_REVID_REG, &val);
if (ret)
return ret;
if (((val & MAX310x_REV_MASK) != MAX3107_REV_ID)) {
dev_err(dev,
"%s ID 0x%02x does not match\n", s->devtype->name, val);
return -ENODEV;
}
return 0;
}
static int max3108_detect(struct device *dev)
{
struct max310x_port *s = dev_get_drvdata(dev);
unsigned int val = 0;
int ret;
/* MAX3108 have not REV ID register, we just check default value
* from clocksource register to make sure everything works.
*/
ret = regmap_read(s->regmap, MAX310X_CLKSRC_REG, &val);
if (ret)
return ret;
if (val != (MAX310X_CLKSRC_EXTCLK_BIT | MAX310X_CLKSRC_PLLBYP_BIT)) {
dev_err(dev, "%s not present\n", s->devtype->name);
return -ENODEV;
}
return 0;
}
static int max3109_detect(struct device *dev)
{
struct max310x_port *s = dev_get_drvdata(dev);
unsigned int val = 0;
int ret;
ret = regmap_read(s->regmap, MAX310X_REVID_REG, &val);
if (ret)
return ret;
if (((val & MAX310x_REV_MASK) != MAX3109_REV_ID)) {
dev_err(dev,
"%s ID 0x%02x does not match\n", s->devtype->name, val);
return -ENODEV;
}
return 0;
}
static void max310x_power(struct uart_port *port, int on)
{
max310x_port_update(port, MAX310X_MODE1_REG,
MAX310X_MODE1_FORCESLEEP_BIT,
on ? 0 : MAX310X_MODE1_FORCESLEEP_BIT);
if (on)
msleep(50);
}
static int max14830_detect(struct device *dev)
{
struct max310x_port *s = dev_get_drvdata(dev);
unsigned int val = 0;
int ret;
ret = regmap_write(s->regmap, MAX310X_GLOBALCMD_REG,
MAX310X_EXTREG_ENBL);
if (ret)
return ret;
regmap_read(s->regmap, MAX310X_REVID_EXTREG, &val);
regmap_write(s->regmap, MAX310X_GLOBALCMD_REG, MAX310X_EXTREG_DSBL);
if (((val & MAX310x_REV_MASK) != MAX14830_REV_ID)) {
dev_err(dev,
"%s ID 0x%02x does not match\n", s->devtype->name, val);
return -ENODEV;
}
return 0;
}
static void max14830_power(struct uart_port *port, int on)
{
max310x_port_update(port, MAX310X_BRGCFG_REG,
MAX14830_BRGCFG_CLKDIS_BIT,
on ? 0 : MAX14830_BRGCFG_CLKDIS_BIT);
if (on)
msleep(50);
}
static const struct max310x_devtype max3107_devtype = {
.name = "MAX3107",
.nr = 1,
.detect = max3107_detect,
.power = max310x_power,
};
static const struct max310x_devtype max3108_devtype = {
.name = "MAX3108",
.nr = 1,
.detect = max3108_detect,
.power = max310x_power,
};
static const struct max310x_devtype max3109_devtype = {
.name = "MAX3109",
.nr = 2,
.detect = max3109_detect,
.power = max310x_power,
};
static const struct max310x_devtype max14830_devtype = {
.name = "MAX14830",
.nr = 4,
.detect = max14830_detect,
.power = max14830_power,
};
static bool max310x_reg_writeable(struct device *dev, unsigned int reg)
{
switch (reg & 0x1f) {
case MAX310X_IRQSTS_REG:
case MAX310X_LSR_IRQSTS_REG:
case MAX310X_SPCHR_IRQSTS_REG:
case MAX310X_STS_IRQSTS_REG:
case MAX310X_TXFIFOLVL_REG:
case MAX310X_RXFIFOLVL_REG:
return false;
default:
break;
}
return true;
}
static bool max310x_reg_volatile(struct device *dev, unsigned int reg)
{
switch (reg & 0x1f) {
case MAX310X_RHR_REG:
case MAX310X_IRQSTS_REG:
case MAX310X_LSR_IRQSTS_REG:
case MAX310X_SPCHR_IRQSTS_REG:
case MAX310X_STS_IRQSTS_REG:
case MAX310X_TXFIFOLVL_REG:
case MAX310X_RXFIFOLVL_REG:
case MAX310X_GPIODATA_REG:
case MAX310X_BRGDIVLSB_REG:
case MAX310X_REG_05:
case MAX310X_REG_1F:
return true;
default:
break;
}
return false;
}
static bool max310x_reg_precious(struct device *dev, unsigned int reg)
{
switch (reg & 0x1f) {
case MAX310X_RHR_REG:
case MAX310X_IRQSTS_REG:
case MAX310X_SPCHR_IRQSTS_REG:
case MAX310X_STS_IRQSTS_REG:
return true;
default:
break;
}
return false;
}
static int max310x_set_baud(struct uart_port *port, int baud)
{
unsigned int mode = 0, clk = port->uartclk, div = clk / baud;
/* Check for minimal value for divider */
if (div < 16)
div = 16;
if (clk % baud && (div / 16) < 0x8000) {
/* Mode x2 */
mode = MAX310X_BRGCFG_2XMODE_BIT;
clk = port->uartclk * 2;
div = clk / baud;
if (clk % baud && (div / 16) < 0x8000) {
/* Mode x4 */
mode = MAX310X_BRGCFG_4XMODE_BIT;
clk = port->uartclk * 4;
div = clk / baud;
}
}
max310x_port_write(port, MAX310X_BRGDIVMSB_REG, (div / 16) >> 8);
max310x_port_write(port, MAX310X_BRGDIVLSB_REG, div / 16);
max310x_port_write(port, MAX310X_BRGCFG_REG, (div % 16) | mode);
return DIV_ROUND_CLOSEST(clk, div);
}
static int max310x_update_best_err(unsigned long f, long *besterr)
{
/* Use baudrate 115200 for calculate error */
long err = f % (115200 * 16);
if ((*besterr < 0) || (*besterr > err)) {
*besterr = err;
return 0;
}
return 1;
}
static int max310x_set_ref_clk(struct max310x_port *s, unsigned long freq,
bool xtal)
{
unsigned int div, clksrc, pllcfg = 0;
long besterr = -1;
unsigned long fdiv, fmul, bestfreq = freq;
/* First, update error without PLL */
max310x_update_best_err(freq, &besterr);
/* Try all possible PLL dividers */
for (div = 1; (div <= 63) && besterr; div++) {
fdiv = DIV_ROUND_CLOSEST(freq, div);
/* Try multiplier 6 */
fmul = fdiv * 6;
if ((fdiv >= 500000) && (fdiv <= 800000))
if (!max310x_update_best_err(fmul, &besterr)) {
pllcfg = (0 << 6) | div;
bestfreq = fmul;
}
/* Try multiplier 48 */
fmul = fdiv * 48;
if ((fdiv >= 850000) && (fdiv <= 1200000))
if (!max310x_update_best_err(fmul, &besterr)) {
pllcfg = (1 << 6) | div;
bestfreq = fmul;
}
/* Try multiplier 96 */
fmul = fdiv * 96;
if ((fdiv >= 425000) && (fdiv <= 1000000))
if (!max310x_update_best_err(fmul, &besterr)) {
pllcfg = (2 << 6) | div;
bestfreq = fmul;
}
/* Try multiplier 144 */
fmul = fdiv * 144;
if ((fdiv >= 390000) && (fdiv <= 667000))
if (!max310x_update_best_err(fmul, &besterr)) {
pllcfg = (3 << 6) | div;
bestfreq = fmul;
}
}
/* Configure clock source */
clksrc = xtal ? MAX310X_CLKSRC_CRYST_BIT : MAX310X_CLKSRC_EXTCLK_BIT;
/* Configure PLL */
if (pllcfg) {
clksrc |= MAX310X_CLKSRC_PLL_BIT;
regmap_write(s->regmap, MAX310X_PLLCFG_REG, pllcfg);
} else
clksrc |= MAX310X_CLKSRC_PLLBYP_BIT;
regmap_write(s->regmap, MAX310X_CLKSRC_REG, clksrc);
/* Wait for crystal */
if (pllcfg && xtal)
msleep(10);
return (int)bestfreq;
}
static void max310x_handle_rx(struct uart_port *port, unsigned int rxlen)
{
unsigned int sts, ch, flag;
if (unlikely(rxlen >= port->fifosize)) {
dev_warn_ratelimited(port->dev,
"Port %i: Possible RX FIFO overrun\n",
port->line);
port->icount.buf_overrun++;
/* Ensure sanity of RX level */
rxlen = port->fifosize;
}
while (rxlen--) {
ch = max310x_port_read(port, MAX310X_RHR_REG);
sts = max310x_port_read(port, MAX310X_LSR_IRQSTS_REG);
sts &= MAX310X_LSR_RXPAR_BIT | MAX310X_LSR_FRERR_BIT |
MAX310X_LSR_RXOVR_BIT | MAX310X_LSR_RXBRK_BIT;
port->icount.rx++;
flag = TTY_NORMAL;
if (unlikely(sts)) {
if (sts & MAX310X_LSR_RXBRK_BIT) {
port->icount.brk++;
if (uart_handle_break(port))
continue;
} else if (sts & MAX310X_LSR_RXPAR_BIT)
port->icount.parity++;
else if (sts & MAX310X_LSR_FRERR_BIT)
port->icount.frame++;
else if (sts & MAX310X_LSR_RXOVR_BIT)
port->icount.overrun++;
sts &= port->read_status_mask;
if (sts & MAX310X_LSR_RXBRK_BIT)
flag = TTY_BREAK;
else if (sts & MAX310X_LSR_RXPAR_BIT)
flag = TTY_PARITY;
else if (sts & MAX310X_LSR_FRERR_BIT)
flag = TTY_FRAME;
else if (sts & MAX310X_LSR_RXOVR_BIT)
flag = TTY_OVERRUN;
}
if (uart_handle_sysrq_char(port, ch))
continue;
if (sts & port->ignore_status_mask)
continue;
uart_insert_char(port, sts, MAX310X_LSR_RXOVR_BIT, ch, flag);
}
tty_flip_buffer_push(&port->state->port);
}
static void max310x_handle_tx(struct uart_port *port)
{
struct circ_buf *xmit = &port->state->xmit;
unsigned int txlen, to_send;
if (unlikely(port->x_char)) {
max310x_port_write(port, MAX310X_THR_REG, port->x_char);
port->icount.tx++;
port->x_char = 0;
return;
}
if (uart_circ_empty(xmit) || uart_tx_stopped(port))
return;
/* Get length of data pending in circular buffer */
to_send = uart_circ_chars_pending(xmit);
if (likely(to_send)) {
/* Limit to size of TX FIFO */
txlen = max310x_port_read(port, MAX310X_TXFIFOLVL_REG);
txlen = port->fifosize - txlen;
to_send = (to_send > txlen) ? txlen : to_send;
/* Add data to send */
port->icount.tx += to_send;
while (to_send--) {
max310x_port_write(port, MAX310X_THR_REG,
xmit->buf[xmit->tail]);
xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
}
}
if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
uart_write_wakeup(port);
}
static void max310x_port_irq(struct max310x_port *s, int portno)
{
struct uart_port *port = &s->p[portno].port;
do {
unsigned int ists, lsr, rxlen;
/* Read IRQ status & RX FIFO level */
ists = max310x_port_read(port, MAX310X_IRQSTS_REG);
rxlen = max310x_port_read(port, MAX310X_RXFIFOLVL_REG);
if (!ists && !rxlen)
break;
if (ists & MAX310X_IRQ_CTS_BIT) {
lsr = max310x_port_read(port, MAX310X_LSR_IRQSTS_REG);
uart_handle_cts_change(port,
!!(lsr & MAX310X_LSR_CTS_BIT));
}
if (rxlen)
max310x_handle_rx(port, rxlen);
if (ists & MAX310X_IRQ_TXEMPTY_BIT) {
mutex_lock(&s->mutex);
max310x_handle_tx(port);
mutex_unlock(&s->mutex);
}
} while (1);
}
static irqreturn_t max310x_ist(int irq, void *dev_id)
{
struct max310x_port *s = (struct max310x_port *)dev_id;
if (s->uart.nr > 1) {
do {
unsigned int val = ~0;
WARN_ON_ONCE(regmap_read(s->regmap,
MAX310X_GLOBALIRQ_REG, &val));
val = ((1 << s->uart.nr) - 1) & ~val;
if (!val)
break;
max310x_port_irq(s, fls(val) - 1);
} while (1);
} else
max310x_port_irq(s, 0);
return IRQ_HANDLED;
}
static void max310x_wq_proc(struct work_struct *ws)
{
struct max310x_one *one = container_of(ws, struct max310x_one, tx_work);
struct max310x_port *s = dev_get_drvdata(one->port.dev);
mutex_lock(&s->mutex);
max310x_handle_tx(&one->port);
mutex_unlock(&s->mutex);
}
static void max310x_start_tx(struct uart_port *port)
{
struct max310x_one *one = container_of(port, struct max310x_one, port);
if (!work_pending(&one->tx_work))
schedule_work(&one->tx_work);
}
static unsigned int max310x_tx_empty(struct uart_port *port)
{
unsigned int lvl, sts;
lvl = max310x_port_read(port, MAX310X_TXFIFOLVL_REG);
sts = max310x_port_read(port, MAX310X_IRQSTS_REG);
return ((sts & MAX310X_IRQ_TXEMPTY_BIT) && !lvl) ? TIOCSER_TEMT : 0;
}
static unsigned int max310x_get_mctrl(struct uart_port *port)
{
/* DCD and DSR are not wired and CTS/RTS is handled automatically
* so just indicate DSR and CAR asserted
*/
return TIOCM_DSR | TIOCM_CAR;
}
static void max310x_md_proc(struct work_struct *ws)
{
struct max310x_one *one = container_of(ws, struct max310x_one, md_work);
max310x_port_update(&one->port, MAX310X_MODE2_REG,
MAX310X_MODE2_LOOPBACK_BIT,
(one->port.mctrl & TIOCM_LOOP) ?
MAX310X_MODE2_LOOPBACK_BIT : 0);
}
static void max310x_set_mctrl(struct uart_port *port, unsigned int mctrl)
{
struct max310x_one *one = container_of(port, struct max310x_one, port);
schedule_work(&one->md_work);
}
static void max310x_break_ctl(struct uart_port *port, int break_state)
{
max310x_port_update(port, MAX310X_LCR_REG,
MAX310X_LCR_TXBREAK_BIT,
break_state ? MAX310X_LCR_TXBREAK_BIT : 0);
}
static void max310x_set_termios(struct uart_port *port,
struct ktermios *termios,
struct ktermios *old)
{
unsigned int lcr, flow = 0;
int baud;
/* Mask termios capabilities we don't support */
termios->c_cflag &= ~CMSPAR;
/* Word size */
switch (termios->c_cflag & CSIZE) {
case CS5:
lcr = MAX310X_LCR_WORD_LEN_5;
break;
case CS6:
lcr = MAX310X_LCR_WORD_LEN_6;
break;
case CS7:
lcr = MAX310X_LCR_WORD_LEN_7;
break;
case CS8:
default:
lcr = MAX310X_LCR_WORD_LEN_8;
break;
}
/* Parity */
if (termios->c_cflag & PARENB) {
lcr |= MAX310X_LCR_PARITY_BIT;
if (!(termios->c_cflag & PARODD))
lcr |= MAX310X_LCR_EVENPARITY_BIT;
}
/* Stop bits */
if (termios->c_cflag & CSTOPB)
lcr |= MAX310X_LCR_STOPLEN_BIT; /* 2 stops */
/* Update LCR register */
max310x_port_write(port, MAX310X_LCR_REG, lcr);
/* Set read status mask */
port->read_status_mask = MAX310X_LSR_RXOVR_BIT;
if (termios->c_iflag & INPCK)
port->read_status_mask |= MAX310X_LSR_RXPAR_BIT |
MAX310X_LSR_FRERR_BIT;
if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK))
port->read_status_mask |= MAX310X_LSR_RXBRK_BIT;
/* Set status ignore mask */
port->ignore_status_mask = 0;
if (termios->c_iflag & IGNBRK)
port->ignore_status_mask |= MAX310X_LSR_RXBRK_BIT;
if (!(termios->c_cflag & CREAD))
port->ignore_status_mask |= MAX310X_LSR_RXPAR_BIT |
MAX310X_LSR_RXOVR_BIT |
MAX310X_LSR_FRERR_BIT |
MAX310X_LSR_RXBRK_BIT;
/* Configure flow control */
max310x_port_write(port, MAX310X_XON1_REG, termios->c_cc[VSTART]);
max310x_port_write(port, MAX310X_XOFF1_REG, termios->c_cc[VSTOP]);
if (termios->c_cflag & CRTSCTS)
flow |= MAX310X_FLOWCTRL_AUTOCTS_BIT |
MAX310X_FLOWCTRL_AUTORTS_BIT;
if (termios->c_iflag & IXON)
flow |= MAX310X_FLOWCTRL_SWFLOW3_BIT |
MAX310X_FLOWCTRL_SWFLOWEN_BIT;
if (termios->c_iflag & IXOFF)
flow |= MAX310X_FLOWCTRL_SWFLOW1_BIT |
MAX310X_FLOWCTRL_SWFLOWEN_BIT;
max310x_port_write(port, MAX310X_FLOWCTRL_REG, flow);
/* Get baud rate generator configuration */
baud = uart_get_baud_rate(port, termios, old,
port->uartclk / 16 / 0xffff,
port->uartclk / 4);
/* Setup baudrate generator */
baud = max310x_set_baud(port, baud);
/* Update timeout according to new baud rate */
uart_update_timeout(port, termios->c_cflag, baud);
}
static int max310x_ioctl(struct uart_port *port, unsigned int cmd,
unsigned long arg)
{
#if defined(TIOCSRS485) && defined(TIOCGRS485)
struct serial_rs485 rs485;
unsigned int val;
switch (cmd) {
case TIOCSRS485:
if (copy_from_user(&rs485, (void __user *)arg, sizeof(rs485)))
return -EFAULT;
if (rs485.delay_rts_before_send > 0x0f ||
rs485.delay_rts_after_send > 0x0f)
return -ERANGE;
val = (rs485.delay_rts_before_send << 4) |
rs485.delay_rts_after_send;
max310x_port_write(port, MAX310X_HDPIXDELAY_REG, val);
if (rs485.flags & SER_RS485_ENABLED) {
max310x_port_update(port, MAX310X_MODE1_REG,
MAX310X_MODE1_TRNSCVCTRL_BIT,
MAX310X_MODE1_TRNSCVCTRL_BIT);
max310x_port_update(port, MAX310X_MODE2_REG,
MAX310X_MODE2_ECHOSUPR_BIT,
MAX310X_MODE2_ECHOSUPR_BIT);
} else {
max310x_port_update(port, MAX310X_MODE1_REG,
MAX310X_MODE1_TRNSCVCTRL_BIT, 0);
max310x_port_update(port, MAX310X_MODE2_REG,
MAX310X_MODE2_ECHOSUPR_BIT, 0);
}
return 0;
case TIOCGRS485:
memset(&rs485, 0, sizeof(rs485));
val = max310x_port_read(port, MAX310X_MODE1_REG);
rs485.flags = (val & MAX310X_MODE1_TRNSCVCTRL_BIT) ?
SER_RS485_ENABLED : 0;
rs485.flags |= SER_RS485_RTS_ON_SEND;
val = max310x_port_read(port, MAX310X_HDPIXDELAY_REG);
rs485.delay_rts_before_send = val >> 4;
rs485.delay_rts_after_send = val & 0x0f;
if (copy_to_user((void __user *)arg, &rs485, sizeof(rs485)))
return -EFAULT;
return 0;
default:
break;
}
#endif
return -ENOIOCTLCMD;
}
static int max310x_startup(struct uart_port *port)
{
struct max310x_port *s = dev_get_drvdata(port->dev);
unsigned int val;
s->devtype->power(port, 1);
/* Configure MODE1 register */
max310x_port_update(port, MAX310X_MODE1_REG,
MAX310X_MODE1_TRNSCVCTRL_BIT, 0);
/* Configure MODE2 register & Reset FIFOs*/
val = MAX310X_MODE2_RXEMPTINV_BIT | MAX310X_MODE2_FIFORST_BIT;
max310x_port_write(port, MAX310X_MODE2_REG, val);
max310x_port_update(port, MAX310X_MODE2_REG,
MAX310X_MODE2_FIFORST_BIT, 0);
/* Configure flow control levels */
/* Flow control halt level 96, resume level 48 */
max310x_port_write(port, MAX310X_FLOWLVL_REG,
MAX310X_FLOWLVL_RES(48) | MAX310X_FLOWLVL_HALT(96));
/* Clear IRQ status register */
max310x_port_read(port, MAX310X_IRQSTS_REG);
/* Enable RX, TX, CTS change interrupts */
val = MAX310X_IRQ_RXEMPTY_BIT | MAX310X_IRQ_TXEMPTY_BIT;
max310x_port_write(port, MAX310X_IRQEN_REG, val | MAX310X_IRQ_CTS_BIT);
return 0;
}
static void max310x_shutdown(struct uart_port *port)
{
struct max310x_port *s = dev_get_drvdata(port->dev);
/* Disable all interrupts */
max310x_port_write(port, MAX310X_IRQEN_REG, 0);
s->devtype->power(port, 0);
}
static const char *max310x_type(struct uart_port *port)
{
struct max310x_port *s = dev_get_drvdata(port->dev);
return (port->type == PORT_MAX310X) ? s->devtype->name : NULL;
}
static int max310x_request_port(struct uart_port *port)
{
/* Do nothing */
return 0;
}
static void max310x_config_port(struct uart_port *port, int flags)
{
if (flags & UART_CONFIG_TYPE)
port->type = PORT_MAX310X;
}
static int max310x_verify_port(struct uart_port *port, struct serial_struct *s)
{
if ((s->type != PORT_UNKNOWN) && (s->type != PORT_MAX310X))
return -EINVAL;
if (s->irq != port->irq)
return -EINVAL;
return 0;
}
static void max310x_null_void(struct uart_port *port)
{
/* Do nothing */
}
static const struct uart_ops max310x_ops = {
.tx_empty = max310x_tx_empty,
.set_mctrl = max310x_set_mctrl,
.get_mctrl = max310x_get_mctrl,
.stop_tx = max310x_null_void,
.start_tx = max310x_start_tx,
.stop_rx = max310x_null_void,
.break_ctl = max310x_break_ctl,
.startup = max310x_startup,
.shutdown = max310x_shutdown,
.set_termios = max310x_set_termios,
.type = max310x_type,
.request_port = max310x_request_port,
.release_port = max310x_null_void,
.config_port = max310x_config_port,
.verify_port = max310x_verify_port,
.ioctl = max310x_ioctl,
};
static int __maybe_unused max310x_suspend(struct device *dev)
{
struct max310x_port *s = dev_get_drvdata(dev);
int i;
for (i = 0; i < s->uart.nr; i++) {
uart_suspend_port(&s->uart, &s->p[i].port);
s->devtype->power(&s->p[i].port, 0);
}
return 0;
}
static int __maybe_unused max310x_resume(struct device *dev)
{
struct max310x_port *s = dev_get_drvdata(dev);
int i;
for (i = 0; i < s->uart.nr; i++) {
s->devtype->power(&s->p[i].port, 1);
uart_resume_port(&s->uart, &s->p[i].port);
}
return 0;
}
static SIMPLE_DEV_PM_OPS(max310x_pm_ops, max310x_suspend, max310x_resume);
#ifdef CONFIG_GPIOLIB
static int max310x_gpio_get(struct gpio_chip *chip, unsigned offset)
{
unsigned int val;
struct max310x_port *s = container_of(chip, struct max310x_port, gpio);
struct uart_port *port = &s->p[offset / 4].port;
val = max310x_port_read(port, MAX310X_GPIODATA_REG);
return !!((val >> 4) & (1 << (offset % 4)));
}
static void max310x_gpio_set(struct gpio_chip *chip, unsigned offset, int value)
{
struct max310x_port *s = container_of(chip, struct max310x_port, gpio);
struct uart_port *port = &s->p[offset / 4].port;
max310x_port_update(port, MAX310X_GPIODATA_REG, 1 << (offset % 4),
value ? 1 << (offset % 4) : 0);
}
static int max310x_gpio_direction_input(struct gpio_chip *chip, unsigned offset)
{
struct max310x_port *s = container_of(chip, struct max310x_port, gpio);
struct uart_port *port = &s->p[offset / 4].port;
max310x_port_update(port, MAX310X_GPIOCFG_REG, 1 << (offset % 4), 0);
return 0;
}
static int max310x_gpio_direction_output(struct gpio_chip *chip,
unsigned offset, int value)
{
struct max310x_port *s = container_of(chip, struct max310x_port, gpio);
struct uart_port *port = &s->p[offset / 4].port;
max310x_port_update(port, MAX310X_GPIODATA_REG, 1 << (offset % 4),
value ? 1 << (offset % 4) : 0);
max310x_port_update(port, MAX310X_GPIOCFG_REG, 1 << (offset % 4),
1 << (offset % 4));
return 0;
}
#endif
static int max310x_probe(struct device *dev, struct max310x_devtype *devtype,
struct regmap *regmap, int irq, unsigned long flags)
{
int i, ret, fmin, fmax, freq, uartclk;
struct clk *clk_osc, *clk_xtal;
struct max310x_port *s;
bool xtal = false;
if (IS_ERR(regmap))
return PTR_ERR(regmap);
/* Alloc port structure */
s = devm_kzalloc(dev, sizeof(*s) +
sizeof(struct max310x_one) * devtype->nr, GFP_KERNEL);
if (!s) {
dev_err(dev, "Error allocating port structure\n");
return -ENOMEM;
}
clk_osc = devm_clk_get(dev, "osc");
clk_xtal = devm_clk_get(dev, "xtal");
if (!IS_ERR(clk_osc)) {
s->clk = clk_osc;
fmin = 500000;
fmax = 35000000;
} else if (!IS_ERR(clk_xtal)) {
s->clk = clk_xtal;
fmin = 1000000;
fmax = 4000000;
xtal = true;
} else if (PTR_ERR(clk_osc) == -EPROBE_DEFER ||
PTR_ERR(clk_xtal) == -EPROBE_DEFER) {
return -EPROBE_DEFER;
} else {
dev_err(dev, "Cannot get clock\n");
return -EINVAL;
}
ret = clk_prepare_enable(s->clk);
if (ret)
return ret;
freq = clk_get_rate(s->clk);
/* Check frequency limits */
if (freq < fmin || freq > fmax) {
ret = -ERANGE;
goto out_clk;
}
s->regmap = regmap;
s->devtype = devtype;
dev_set_drvdata(dev, s);
/* Check device to ensure we are talking to what we expect */
ret = devtype->detect(dev);
if (ret)
goto out_clk;
for (i = 0; i < devtype->nr; i++) {
unsigned int offs = i << 5;
/* Reset port */
regmap_write(s->regmap, MAX310X_MODE2_REG + offs,
MAX310X_MODE2_RST_BIT);
/* Clear port reset */
regmap_write(s->regmap, MAX310X_MODE2_REG + offs, 0);
/* Wait for port startup */
do {
regmap_read(s->regmap,
MAX310X_BRGDIVLSB_REG + offs, &ret);
} while (ret != 0x01);
regmap_update_bits(s->regmap, MAX310X_MODE1_REG + offs,
MAX310X_MODE1_AUTOSLEEP_BIT,
MAX310X_MODE1_AUTOSLEEP_BIT);
}
uartclk = max310x_set_ref_clk(s, freq, xtal);
dev_dbg(dev, "Reference clock set to %i Hz\n", uartclk);
/* Register UART driver */
s->uart.owner = THIS_MODULE;
s->uart.dev_name = "ttyMAX";
s->uart.major = MAX310X_MAJOR;
s->uart.minor = MAX310X_MINOR;
s->uart.nr = devtype->nr;
ret = uart_register_driver(&s->uart);
if (ret) {
dev_err(dev, "Registering UART driver failed\n");
goto out_clk;
}
#ifdef CONFIG_GPIOLIB
/* Setup GPIO cotroller */
s->gpio.owner = THIS_MODULE;
s->gpio.dev = dev;
s->gpio.label = dev_name(dev);
s->gpio.direction_input = max310x_gpio_direction_input;
s->gpio.get = max310x_gpio_get;
s->gpio.direction_output= max310x_gpio_direction_output;
s->gpio.set = max310x_gpio_set;
s->gpio.base = -1;
s->gpio.ngpio = devtype->nr * 4;
s->gpio.can_sleep = 1;
ret = gpiochip_add(&s->gpio);
if (ret)
goto out_uart;
#endif
mutex_init(&s->mutex);
for (i = 0; i < devtype->nr; i++) {
/* Initialize port data */
s->p[i].port.line = i;
s->p[i].port.dev = dev;
s->p[i].port.irq = irq;
s->p[i].port.type = PORT_MAX310X;
s->p[i].port.fifosize = MAX310X_FIFO_SIZE;
s->p[i].port.flags = UPF_FIXED_TYPE | UPF_LOW_LATENCY;
s->p[i].port.iotype = UPIO_PORT;
s->p[i].port.iobase = i * 0x20;
s->p[i].port.membase = (void __iomem *)~0;
s->p[i].port.uartclk = uartclk;
s->p[i].port.ops = &max310x_ops;
/* Disable all interrupts */
max310x_port_write(&s->p[i].port, MAX310X_IRQEN_REG, 0);
/* Clear IRQ status register */
max310x_port_read(&s->p[i].port, MAX310X_IRQSTS_REG);
/* Enable IRQ pin */
max310x_port_update(&s->p[i].port, MAX310X_MODE1_REG,
MAX310X_MODE1_IRQSEL_BIT,
MAX310X_MODE1_IRQSEL_BIT);
/* Initialize queue for start TX */
INIT_WORK(&s->p[i].tx_work, max310x_wq_proc);
/* Initialize queue for changing mode */
INIT_WORK(&s->p[i].md_work, max310x_md_proc);
/* Register port */
uart_add_one_port(&s->uart, &s->p[i].port);
/* Go to suspend mode */
devtype->power(&s->p[i].port, 0);
}
/* Setup interrupt */
ret = devm_request_threaded_irq(dev, irq, NULL, max310x_ist,
IRQF_ONESHOT | flags, dev_name(dev), s);
if (!ret)
return 0;
dev_err(dev, "Unable to reguest IRQ %i\n", irq);
mutex_destroy(&s->mutex);
#ifdef CONFIG_GPIOLIB
WARN_ON(gpiochip_remove(&s->gpio));
out_uart:
#endif
uart_unregister_driver(&s->uart);
out_clk:
clk_disable_unprepare(s->clk);
return ret;
}
static int max310x_remove(struct device *dev)
{
struct max310x_port *s = dev_get_drvdata(dev);
int i, ret = 0;
#ifdef CONFIG_GPIOLIB
ret = gpiochip_remove(&s->gpio);
if (ret)
return ret;
#endif
for (i = 0; i < s->uart.nr; i++) {
cancel_work_sync(&s->p[i].tx_work);
cancel_work_sync(&s->p[i].md_work);
uart_remove_one_port(&s->uart, &s->p[i].port);
s->devtype->power(&s->p[i].port, 0);
}
mutex_destroy(&s->mutex);
uart_unregister_driver(&s->uart);
clk_disable_unprepare(s->clk);
return ret;
}
static const struct of_device_id __maybe_unused max310x_dt_ids[] = {
{ .compatible = "maxim,max3107", .data = &max3107_devtype, },
{ .compatible = "maxim,max3108", .data = &max3108_devtype, },
{ .compatible = "maxim,max3109", .data = &max3109_devtype, },
{ .compatible = "maxim,max14830", .data = &max14830_devtype },
{ }
};
MODULE_DEVICE_TABLE(of, max310x_dt_ids);
static struct regmap_config regcfg = {
.reg_bits = 8,
.val_bits = 8,
.write_flag_mask = 0x80,
.cache_type = REGCACHE_RBTREE,
.writeable_reg = max310x_reg_writeable,
.volatile_reg = max310x_reg_volatile,
.precious_reg = max310x_reg_precious,
};
#ifdef CONFIG_SPI_MASTER
static int max310x_spi_probe(struct spi_device *spi)
{
struct max310x_devtype *devtype;
unsigned long flags = 0;
struct regmap *regmap;
int ret;
/* Setup SPI bus */
spi->bits_per_word = 8;
spi->mode = spi->mode ? : SPI_MODE_0;
spi->max_speed_hz = spi->max_speed_hz ? : 26000000;
ret = spi_setup(spi);
if (ret)
return ret;
if (spi->dev.of_node) {
const struct of_device_id *of_id =
of_match_device(max310x_dt_ids, &spi->dev);
devtype = (struct max310x_devtype *)of_id->data;
} else {
const struct spi_device_id *id_entry = spi_get_device_id(spi);
devtype = (struct max310x_devtype *)id_entry->driver_data;
flags = IRQF_TRIGGER_FALLING;
}
regcfg.max_register = devtype->nr * 0x20 - 1;
regmap = devm_regmap_init_spi(spi, &regcfg);
return max310x_probe(&spi->dev, devtype, regmap, spi->irq, flags);
}
static int max310x_spi_remove(struct spi_device *spi)
{
return max310x_remove(&spi->dev);
}
static const struct spi_device_id max310x_id_table[] = {
{ "max3107", (kernel_ulong_t)&max3107_devtype, },
{ "max3108", (kernel_ulong_t)&max3108_devtype, },
{ "max3109", (kernel_ulong_t)&max3109_devtype, },
{ "max14830", (kernel_ulong_t)&max14830_devtype, },
{ }
};
MODULE_DEVICE_TABLE(spi, max310x_id_table);
static struct spi_driver max310x_uart_driver = {
.driver = {
.name = MAX310X_NAME,
.owner = THIS_MODULE,
.of_match_table = of_match_ptr(max310x_dt_ids),
.pm = &max310x_pm_ops,
},
.probe = max310x_spi_probe,
.remove = max310x_spi_remove,
.id_table = max310x_id_table,
};
module_spi_driver(max310x_uart_driver);
#endif
MODULE_LICENSE("GPL");
MODULE_AUTHOR("Alexander Shiyan <shc_work@mail.ru>");
MODULE_DESCRIPTION("MAX310X serial driver");