| // SPDX-License-Identifier: GPL-2.0-or-later |
| /* |
| * Janz MODULbus VMOD-TTL GPIO Driver |
| * |
| * Copyright (c) 2010 Ira W. Snyder <iws@ovro.caltech.edu> |
| */ |
| |
| #include <linux/kernel.h> |
| #include <linux/module.h> |
| #include <linux/init.h> |
| #include <linux/interrupt.h> |
| #include <linux/delay.h> |
| #include <linux/platform_device.h> |
| #include <linux/io.h> |
| #include <linux/gpio/driver.h> |
| #include <linux/slab.h> |
| #include <linux/bitops.h> |
| |
| #include <linux/mfd/janz.h> |
| |
| #define DRV_NAME "janz-ttl" |
| |
| #define PORTA_DIRECTION 0x23 |
| #define PORTB_DIRECTION 0x2B |
| #define PORTC_DIRECTION 0x06 |
| #define PORTA_IOCTL 0x24 |
| #define PORTB_IOCTL 0x2C |
| #define PORTC_IOCTL 0x07 |
| |
| #define MASTER_INT_CTL 0x00 |
| #define MASTER_CONF_CTL 0x01 |
| |
| #define CONF_PAE BIT(2) |
| #define CONF_PBE BIT(7) |
| #define CONF_PCE BIT(4) |
| |
| struct ttl_control_regs { |
| __be16 portc; |
| __be16 portb; |
| __be16 porta; |
| __be16 control; |
| }; |
| |
| struct ttl_module { |
| struct gpio_chip gpio; |
| |
| /* base address of registers */ |
| struct ttl_control_regs __iomem *regs; |
| |
| u8 portc_shadow; |
| u8 portb_shadow; |
| u8 porta_shadow; |
| |
| spinlock_t lock; |
| }; |
| |
| static int ttl_get_value(struct gpio_chip *gpio, unsigned offset) |
| { |
| struct ttl_module *mod = dev_get_drvdata(gpio->parent); |
| u8 *shadow; |
| int ret; |
| |
| if (offset < 8) { |
| shadow = &mod->porta_shadow; |
| } else if (offset < 16) { |
| shadow = &mod->portb_shadow; |
| offset -= 8; |
| } else { |
| shadow = &mod->portc_shadow; |
| offset -= 16; |
| } |
| |
| spin_lock(&mod->lock); |
| ret = *shadow & BIT(offset); |
| spin_unlock(&mod->lock); |
| return !!ret; |
| } |
| |
| static void ttl_set_value(struct gpio_chip *gpio, unsigned offset, int value) |
| { |
| struct ttl_module *mod = dev_get_drvdata(gpio->parent); |
| void __iomem *port; |
| u8 *shadow; |
| |
| if (offset < 8) { |
| port = &mod->regs->porta; |
| shadow = &mod->porta_shadow; |
| } else if (offset < 16) { |
| port = &mod->regs->portb; |
| shadow = &mod->portb_shadow; |
| offset -= 8; |
| } else { |
| port = &mod->regs->portc; |
| shadow = &mod->portc_shadow; |
| offset -= 16; |
| } |
| |
| spin_lock(&mod->lock); |
| if (value) |
| *shadow |= BIT(offset); |
| else |
| *shadow &= ~BIT(offset); |
| |
| iowrite16be(*shadow, port); |
| spin_unlock(&mod->lock); |
| } |
| |
| static void ttl_write_reg(struct ttl_module *mod, u8 reg, u16 val) |
| { |
| iowrite16be(reg, &mod->regs->control); |
| iowrite16be(val, &mod->regs->control); |
| } |
| |
| static void ttl_setup_device(struct ttl_module *mod) |
| { |
| /* reset the device to a known state */ |
| iowrite16be(0x0000, &mod->regs->control); |
| iowrite16be(0x0001, &mod->regs->control); |
| iowrite16be(0x0000, &mod->regs->control); |
| |
| /* put all ports in open-drain mode */ |
| ttl_write_reg(mod, PORTA_IOCTL, 0x00ff); |
| ttl_write_reg(mod, PORTB_IOCTL, 0x00ff); |
| ttl_write_reg(mod, PORTC_IOCTL, 0x000f); |
| |
| /* set all ports as outputs */ |
| ttl_write_reg(mod, PORTA_DIRECTION, 0x0000); |
| ttl_write_reg(mod, PORTB_DIRECTION, 0x0000); |
| ttl_write_reg(mod, PORTC_DIRECTION, 0x0000); |
| |
| /* set all ports to drive zeroes */ |
| iowrite16be(0x0000, &mod->regs->porta); |
| iowrite16be(0x0000, &mod->regs->portb); |
| iowrite16be(0x0000, &mod->regs->portc); |
| |
| /* enable all ports */ |
| ttl_write_reg(mod, MASTER_CONF_CTL, CONF_PAE | CONF_PBE | CONF_PCE); |
| } |
| |
| static int ttl_probe(struct platform_device *pdev) |
| { |
| struct janz_platform_data *pdata; |
| struct device *dev = &pdev->dev; |
| struct ttl_module *mod; |
| struct gpio_chip *gpio; |
| int ret; |
| |
| pdata = dev_get_platdata(&pdev->dev); |
| if (!pdata) { |
| dev_err(dev, "no platform data\n"); |
| return -ENXIO; |
| } |
| |
| mod = devm_kzalloc(dev, sizeof(*mod), GFP_KERNEL); |
| if (!mod) |
| return -ENOMEM; |
| |
| platform_set_drvdata(pdev, mod); |
| spin_lock_init(&mod->lock); |
| |
| /* get access to the MODULbus registers for this module */ |
| mod->regs = devm_platform_ioremap_resource(pdev, 0); |
| if (IS_ERR(mod->regs)) |
| return PTR_ERR(mod->regs); |
| |
| ttl_setup_device(mod); |
| |
| /* Initialize the GPIO data structures */ |
| gpio = &mod->gpio; |
| gpio->parent = &pdev->dev; |
| gpio->label = pdev->name; |
| gpio->get = ttl_get_value; |
| gpio->set = ttl_set_value; |
| gpio->owner = THIS_MODULE; |
| |
| /* request dynamic allocation */ |
| gpio->base = -1; |
| gpio->ngpio = 20; |
| |
| ret = devm_gpiochip_add_data(dev, gpio, NULL); |
| if (ret) { |
| dev_err(dev, "unable to add GPIO chip\n"); |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static struct platform_driver ttl_driver = { |
| .driver = { |
| .name = DRV_NAME, |
| }, |
| .probe = ttl_probe, |
| }; |
| |
| module_platform_driver(ttl_driver); |
| |
| MODULE_AUTHOR("Ira W. Snyder <iws@ovro.caltech.edu>"); |
| MODULE_DESCRIPTION("Janz MODULbus VMOD-TTL Driver"); |
| MODULE_LICENSE("GPL"); |
| MODULE_ALIAS("platform:janz-ttl"); |