| // SPDX-License-Identifier: GPL-2.0-only |
| /* |
| * linux/drivers/mmc/host/omap.c |
| * |
| * Copyright (C) 2004 Nokia Corporation |
| * Written by Tuukka Tikkanen and Juha Yrjölä<juha.yrjola@nokia.com> |
| * Misc hacks here and there by Tony Lindgren <tony@atomide.com> |
| * Other hacks (DMA, SD, etc) by David Brownell |
| */ |
| |
| #include <linux/module.h> |
| #include <linux/moduleparam.h> |
| #include <linux/init.h> |
| #include <linux/ioport.h> |
| #include <linux/platform_device.h> |
| #include <linux/interrupt.h> |
| #include <linux/dmaengine.h> |
| #include <linux/dma-mapping.h> |
| #include <linux/delay.h> |
| #include <linux/spinlock.h> |
| #include <linux/timer.h> |
| #include <linux/of.h> |
| #include <linux/mmc/host.h> |
| #include <linux/mmc/card.h> |
| #include <linux/mmc/mmc.h> |
| #include <linux/clk.h> |
| #include <linux/scatterlist.h> |
| #include <linux/slab.h> |
| #include <linux/gpio/consumer.h> |
| #include <linux/platform_data/mmc-omap.h> |
| |
| |
| #define OMAP_MMC_REG_CMD 0x00 |
| #define OMAP_MMC_REG_ARGL 0x01 |
| #define OMAP_MMC_REG_ARGH 0x02 |
| #define OMAP_MMC_REG_CON 0x03 |
| #define OMAP_MMC_REG_STAT 0x04 |
| #define OMAP_MMC_REG_IE 0x05 |
| #define OMAP_MMC_REG_CTO 0x06 |
| #define OMAP_MMC_REG_DTO 0x07 |
| #define OMAP_MMC_REG_DATA 0x08 |
| #define OMAP_MMC_REG_BLEN 0x09 |
| #define OMAP_MMC_REG_NBLK 0x0a |
| #define OMAP_MMC_REG_BUF 0x0b |
| #define OMAP_MMC_REG_SDIO 0x0d |
| #define OMAP_MMC_REG_REV 0x0f |
| #define OMAP_MMC_REG_RSP0 0x10 |
| #define OMAP_MMC_REG_RSP1 0x11 |
| #define OMAP_MMC_REG_RSP2 0x12 |
| #define OMAP_MMC_REG_RSP3 0x13 |
| #define OMAP_MMC_REG_RSP4 0x14 |
| #define OMAP_MMC_REG_RSP5 0x15 |
| #define OMAP_MMC_REG_RSP6 0x16 |
| #define OMAP_MMC_REG_RSP7 0x17 |
| #define OMAP_MMC_REG_IOSR 0x18 |
| #define OMAP_MMC_REG_SYSC 0x19 |
| #define OMAP_MMC_REG_SYSS 0x1a |
| |
| #define OMAP_MMC_STAT_CARD_ERR (1 << 14) |
| #define OMAP_MMC_STAT_CARD_IRQ (1 << 13) |
| #define OMAP_MMC_STAT_OCR_BUSY (1 << 12) |
| #define OMAP_MMC_STAT_A_EMPTY (1 << 11) |
| #define OMAP_MMC_STAT_A_FULL (1 << 10) |
| #define OMAP_MMC_STAT_CMD_CRC (1 << 8) |
| #define OMAP_MMC_STAT_CMD_TOUT (1 << 7) |
| #define OMAP_MMC_STAT_DATA_CRC (1 << 6) |
| #define OMAP_MMC_STAT_DATA_TOUT (1 << 5) |
| #define OMAP_MMC_STAT_END_BUSY (1 << 4) |
| #define OMAP_MMC_STAT_END_OF_DATA (1 << 3) |
| #define OMAP_MMC_STAT_CARD_BUSY (1 << 2) |
| #define OMAP_MMC_STAT_END_OF_CMD (1 << 0) |
| |
| #define mmc_omap7xx() (host->features & MMC_OMAP7XX) |
| #define mmc_omap15xx() (host->features & MMC_OMAP15XX) |
| #define mmc_omap16xx() (host->features & MMC_OMAP16XX) |
| #define MMC_OMAP1_MASK (MMC_OMAP7XX | MMC_OMAP15XX | MMC_OMAP16XX) |
| #define mmc_omap1() (host->features & MMC_OMAP1_MASK) |
| #define mmc_omap2() (!mmc_omap1()) |
| |
| #define OMAP_MMC_REG(host, reg) (OMAP_MMC_REG_##reg << (host)->reg_shift) |
| #define OMAP_MMC_READ(host, reg) __raw_readw((host)->virt_base + OMAP_MMC_REG(host, reg)) |
| #define OMAP_MMC_WRITE(host, reg, val) __raw_writew((val), (host)->virt_base + OMAP_MMC_REG(host, reg)) |
| |
| /* |
| * Command types |
| */ |
| #define OMAP_MMC_CMDTYPE_BC 0 |
| #define OMAP_MMC_CMDTYPE_BCR 1 |
| #define OMAP_MMC_CMDTYPE_AC 2 |
| #define OMAP_MMC_CMDTYPE_ADTC 3 |
| |
| #define DRIVER_NAME "mmci-omap" |
| |
| /* Specifies how often in millisecs to poll for card status changes |
| * when the cover switch is open */ |
| #define OMAP_MMC_COVER_POLL_DELAY 500 |
| |
| struct mmc_omap_host; |
| |
| struct mmc_omap_slot { |
| int id; |
| unsigned int vdd; |
| u16 saved_con; |
| u16 bus_mode; |
| u16 power_mode; |
| unsigned int fclk_freq; |
| |
| struct tasklet_struct cover_tasklet; |
| struct timer_list cover_timer; |
| unsigned cover_open; |
| |
| struct mmc_request *mrq; |
| struct mmc_omap_host *host; |
| struct mmc_host *mmc; |
| struct gpio_desc *vsd; |
| struct gpio_desc *vio; |
| struct gpio_desc *cover; |
| struct omap_mmc_slot_data *pdata; |
| }; |
| |
| struct mmc_omap_host { |
| int initialized; |
| struct mmc_request * mrq; |
| struct mmc_command * cmd; |
| struct mmc_data * data; |
| struct mmc_host * mmc; |
| struct device * dev; |
| unsigned char id; /* 16xx chips have 2 MMC blocks */ |
| struct clk * iclk; |
| struct clk * fclk; |
| struct dma_chan *dma_rx; |
| u32 dma_rx_burst; |
| struct dma_chan *dma_tx; |
| u32 dma_tx_burst; |
| void __iomem *virt_base; |
| unsigned int phys_base; |
| int irq; |
| unsigned char bus_mode; |
| unsigned int reg_shift; |
| struct gpio_desc *slot_switch; |
| |
| struct work_struct cmd_abort_work; |
| unsigned abort:1; |
| struct timer_list cmd_abort_timer; |
| |
| struct work_struct slot_release_work; |
| struct mmc_omap_slot *next_slot; |
| struct work_struct send_stop_work; |
| struct mmc_data *stop_data; |
| |
| unsigned int sg_len; |
| int sg_idx; |
| u16 * buffer; |
| u32 buffer_bytes_left; |
| u32 total_bytes_left; |
| |
| unsigned features; |
| unsigned brs_received:1, dma_done:1; |
| unsigned dma_in_use:1; |
| spinlock_t dma_lock; |
| |
| struct mmc_omap_slot *slots[OMAP_MMC_MAX_SLOTS]; |
| struct mmc_omap_slot *current_slot; |
| spinlock_t slot_lock; |
| wait_queue_head_t slot_wq; |
| int nr_slots; |
| |
| struct timer_list clk_timer; |
| spinlock_t clk_lock; /* for changing enabled state */ |
| unsigned int fclk_enabled:1; |
| struct workqueue_struct *mmc_omap_wq; |
| |
| struct omap_mmc_platform_data *pdata; |
| }; |
| |
| |
| static void mmc_omap_fclk_offdelay(struct mmc_omap_slot *slot) |
| { |
| unsigned long tick_ns; |
| |
| if (slot != NULL && slot->host->fclk_enabled && slot->fclk_freq > 0) { |
| tick_ns = DIV_ROUND_UP(NSEC_PER_SEC, slot->fclk_freq); |
| ndelay(8 * tick_ns); |
| } |
| } |
| |
| static void mmc_omap_fclk_enable(struct mmc_omap_host *host, unsigned int enable) |
| { |
| unsigned long flags; |
| |
| spin_lock_irqsave(&host->clk_lock, flags); |
| if (host->fclk_enabled != enable) { |
| host->fclk_enabled = enable; |
| if (enable) |
| clk_enable(host->fclk); |
| else |
| clk_disable(host->fclk); |
| } |
| spin_unlock_irqrestore(&host->clk_lock, flags); |
| } |
| |
| static void mmc_omap_select_slot(struct mmc_omap_slot *slot, int claimed) |
| { |
| struct mmc_omap_host *host = slot->host; |
| unsigned long flags; |
| |
| if (claimed) |
| goto no_claim; |
| spin_lock_irqsave(&host->slot_lock, flags); |
| while (host->mmc != NULL) { |
| spin_unlock_irqrestore(&host->slot_lock, flags); |
| wait_event(host->slot_wq, host->mmc == NULL); |
| spin_lock_irqsave(&host->slot_lock, flags); |
| } |
| host->mmc = slot->mmc; |
| spin_unlock_irqrestore(&host->slot_lock, flags); |
| no_claim: |
| del_timer(&host->clk_timer); |
| if (host->current_slot != slot || !claimed) |
| mmc_omap_fclk_offdelay(host->current_slot); |
| |
| if (host->current_slot != slot) { |
| OMAP_MMC_WRITE(host, CON, slot->saved_con & 0xFC00); |
| if (host->slot_switch) |
| /* |
| * With two slots and a simple GPIO switch, setting |
| * the GPIO to 0 selects slot ID 0, setting it to 1 |
| * selects slot ID 1. |
| */ |
| gpiod_set_value(host->slot_switch, slot->id); |
| host->current_slot = slot; |
| } |
| |
| if (claimed) { |
| mmc_omap_fclk_enable(host, 1); |
| |
| /* Doing the dummy read here seems to work around some bug |
| * at least in OMAP24xx silicon where the command would not |
| * start after writing the CMD register. Sigh. */ |
| OMAP_MMC_READ(host, CON); |
| |
| OMAP_MMC_WRITE(host, CON, slot->saved_con); |
| } else |
| mmc_omap_fclk_enable(host, 0); |
| } |
| |
| static void mmc_omap_start_request(struct mmc_omap_host *host, |
| struct mmc_request *req); |
| |
| static void mmc_omap_slot_release_work(struct work_struct *work) |
| { |
| struct mmc_omap_host *host = container_of(work, struct mmc_omap_host, |
| slot_release_work); |
| struct mmc_omap_slot *next_slot = host->next_slot; |
| struct mmc_request *rq; |
| |
| host->next_slot = NULL; |
| mmc_omap_select_slot(next_slot, 1); |
| |
| rq = next_slot->mrq; |
| next_slot->mrq = NULL; |
| mmc_omap_start_request(host, rq); |
| } |
| |
| static void mmc_omap_release_slot(struct mmc_omap_slot *slot, int clk_enabled) |
| { |
| struct mmc_omap_host *host = slot->host; |
| unsigned long flags; |
| int i; |
| |
| BUG_ON(slot == NULL || host->mmc == NULL); |
| |
| if (clk_enabled) |
| /* Keeps clock running for at least 8 cycles on valid freq */ |
| mod_timer(&host->clk_timer, jiffies + HZ/10); |
| else { |
| del_timer(&host->clk_timer); |
| mmc_omap_fclk_offdelay(slot); |
| mmc_omap_fclk_enable(host, 0); |
| } |
| |
| spin_lock_irqsave(&host->slot_lock, flags); |
| /* Check for any pending requests */ |
| for (i = 0; i < host->nr_slots; i++) { |
| struct mmc_omap_slot *new_slot; |
| |
| if (host->slots[i] == NULL || host->slots[i]->mrq == NULL) |
| continue; |
| |
| BUG_ON(host->next_slot != NULL); |
| new_slot = host->slots[i]; |
| /* The current slot should not have a request in queue */ |
| BUG_ON(new_slot == host->current_slot); |
| |
| host->next_slot = new_slot; |
| host->mmc = new_slot->mmc; |
| spin_unlock_irqrestore(&host->slot_lock, flags); |
| queue_work(host->mmc_omap_wq, &host->slot_release_work); |
| return; |
| } |
| |
| host->mmc = NULL; |
| wake_up(&host->slot_wq); |
| spin_unlock_irqrestore(&host->slot_lock, flags); |
| } |
| |
| static inline |
| int mmc_omap_cover_is_open(struct mmc_omap_slot *slot) |
| { |
| /* If we have a GPIO then use that */ |
| if (slot->cover) |
| return gpiod_get_value(slot->cover); |
| if (slot->pdata->get_cover_state) |
| return slot->pdata->get_cover_state(mmc_dev(slot->mmc), |
| slot->id); |
| return 0; |
| } |
| |
| static ssize_t |
| mmc_omap_show_cover_switch(struct device *dev, struct device_attribute *attr, |
| char *buf) |
| { |
| struct mmc_host *mmc = container_of(dev, struct mmc_host, class_dev); |
| struct mmc_omap_slot *slot = mmc_priv(mmc); |
| |
| return sprintf(buf, "%s\n", mmc_omap_cover_is_open(slot) ? "open" : |
| "closed"); |
| } |
| |
| static DEVICE_ATTR(cover_switch, S_IRUGO, mmc_omap_show_cover_switch, NULL); |
| |
| static ssize_t |
| mmc_omap_show_slot_name(struct device *dev, struct device_attribute *attr, |
| char *buf) |
| { |
| struct mmc_host *mmc = container_of(dev, struct mmc_host, class_dev); |
| struct mmc_omap_slot *slot = mmc_priv(mmc); |
| |
| return sprintf(buf, "%s\n", slot->pdata->name); |
| } |
| |
| static DEVICE_ATTR(slot_name, S_IRUGO, mmc_omap_show_slot_name, NULL); |
| |
| static void |
| mmc_omap_start_command(struct mmc_omap_host *host, struct mmc_command *cmd) |
| { |
| u32 cmdreg; |
| u32 resptype; |
| u32 cmdtype; |
| u16 irq_mask; |
| |
| host->cmd = cmd; |
| |
| resptype = 0; |
| cmdtype = 0; |
| |
| /* Our hardware needs to know exact type */ |
| switch (mmc_resp_type(cmd)) { |
| case MMC_RSP_NONE: |
| break; |
| case MMC_RSP_R1: |
| case MMC_RSP_R1B: |
| /* resp 1, 1b, 6, 7 */ |
| resptype = 1; |
| break; |
| case MMC_RSP_R2: |
| resptype = 2; |
| break; |
| case MMC_RSP_R3: |
| resptype = 3; |
| break; |
| default: |
| dev_err(mmc_dev(host->mmc), "Invalid response type: %04x\n", mmc_resp_type(cmd)); |
| break; |
| } |
| |
| if (mmc_cmd_type(cmd) == MMC_CMD_ADTC) { |
| cmdtype = OMAP_MMC_CMDTYPE_ADTC; |
| } else if (mmc_cmd_type(cmd) == MMC_CMD_BC) { |
| cmdtype = OMAP_MMC_CMDTYPE_BC; |
| } else if (mmc_cmd_type(cmd) == MMC_CMD_BCR) { |
| cmdtype = OMAP_MMC_CMDTYPE_BCR; |
| } else { |
| cmdtype = OMAP_MMC_CMDTYPE_AC; |
| } |
| |
| cmdreg = cmd->opcode | (resptype << 8) | (cmdtype << 12); |
| |
| if (host->current_slot->bus_mode == MMC_BUSMODE_OPENDRAIN) |
| cmdreg |= 1 << 6; |
| |
| if (cmd->flags & MMC_RSP_BUSY) |
| cmdreg |= 1 << 11; |
| |
| if (host->data && !(host->data->flags & MMC_DATA_WRITE)) |
| cmdreg |= 1 << 15; |
| |
| mod_timer(&host->cmd_abort_timer, jiffies + HZ/2); |
| |
| OMAP_MMC_WRITE(host, CTO, 200); |
| OMAP_MMC_WRITE(host, ARGL, cmd->arg & 0xffff); |
| OMAP_MMC_WRITE(host, ARGH, cmd->arg >> 16); |
| irq_mask = OMAP_MMC_STAT_A_EMPTY | OMAP_MMC_STAT_A_FULL | |
| OMAP_MMC_STAT_CMD_CRC | OMAP_MMC_STAT_CMD_TOUT | |
| OMAP_MMC_STAT_DATA_CRC | OMAP_MMC_STAT_DATA_TOUT | |
| OMAP_MMC_STAT_END_OF_CMD | OMAP_MMC_STAT_CARD_ERR | |
| OMAP_MMC_STAT_END_OF_DATA; |
| if (cmd->opcode == MMC_ERASE) |
| irq_mask &= ~OMAP_MMC_STAT_DATA_TOUT; |
| OMAP_MMC_WRITE(host, IE, irq_mask); |
| OMAP_MMC_WRITE(host, CMD, cmdreg); |
| } |
| |
| static void |
| mmc_omap_release_dma(struct mmc_omap_host *host, struct mmc_data *data, |
| int abort) |
| { |
| enum dma_data_direction dma_data_dir; |
| struct device *dev = mmc_dev(host->mmc); |
| struct dma_chan *c; |
| |
| if (data->flags & MMC_DATA_WRITE) { |
| dma_data_dir = DMA_TO_DEVICE; |
| c = host->dma_tx; |
| } else { |
| dma_data_dir = DMA_FROM_DEVICE; |
| c = host->dma_rx; |
| } |
| if (c) { |
| if (data->error) { |
| dmaengine_terminate_all(c); |
| /* Claim nothing transferred on error... */ |
| data->bytes_xfered = 0; |
| } |
| dev = c->device->dev; |
| } |
| dma_unmap_sg(dev, data->sg, host->sg_len, dma_data_dir); |
| } |
| |
| static void mmc_omap_send_stop_work(struct work_struct *work) |
| { |
| struct mmc_omap_host *host = container_of(work, struct mmc_omap_host, |
| send_stop_work); |
| struct mmc_omap_slot *slot = host->current_slot; |
| struct mmc_data *data = host->stop_data; |
| unsigned long tick_ns; |
| |
| tick_ns = DIV_ROUND_UP(NSEC_PER_SEC, slot->fclk_freq); |
| ndelay(8*tick_ns); |
| |
| mmc_omap_start_command(host, data->stop); |
| } |
| |
| static void |
| mmc_omap_xfer_done(struct mmc_omap_host *host, struct mmc_data *data) |
| { |
| if (host->dma_in_use) |
| mmc_omap_release_dma(host, data, data->error); |
| |
| host->data = NULL; |
| host->sg_len = 0; |
| |
| /* NOTE: MMC layer will sometimes poll-wait CMD13 next, issuing |
| * dozens of requests until the card finishes writing data. |
| * It'd be cheaper to just wait till an EOFB interrupt arrives... |
| */ |
| |
| if (!data->stop) { |
| struct mmc_host *mmc; |
| |
| host->mrq = NULL; |
| mmc = host->mmc; |
| mmc_omap_release_slot(host->current_slot, 1); |
| mmc_request_done(mmc, data->mrq); |
| return; |
| } |
| |
| host->stop_data = data; |
| queue_work(host->mmc_omap_wq, &host->send_stop_work); |
| } |
| |
| static void |
| mmc_omap_send_abort(struct mmc_omap_host *host, int maxloops) |
| { |
| struct mmc_omap_slot *slot = host->current_slot; |
| unsigned int restarts, passes, timeout; |
| u16 stat = 0; |
| |
| /* Sending abort takes 80 clocks. Have some extra and round up */ |
| timeout = DIV_ROUND_UP(120 * USEC_PER_SEC, slot->fclk_freq); |
| restarts = 0; |
| while (restarts < maxloops) { |
| OMAP_MMC_WRITE(host, STAT, 0xFFFF); |
| OMAP_MMC_WRITE(host, CMD, (3 << 12) | (1 << 7)); |
| |
| passes = 0; |
| while (passes < timeout) { |
| stat = OMAP_MMC_READ(host, STAT); |
| if (stat & OMAP_MMC_STAT_END_OF_CMD) |
| goto out; |
| udelay(1); |
| passes++; |
| } |
| |
| restarts++; |
| } |
| out: |
| OMAP_MMC_WRITE(host, STAT, stat); |
| } |
| |
| static void |
| mmc_omap_abort_xfer(struct mmc_omap_host *host, struct mmc_data *data) |
| { |
| if (host->dma_in_use) |
| mmc_omap_release_dma(host, data, 1); |
| |
| host->data = NULL; |
| host->sg_len = 0; |
| |
| mmc_omap_send_abort(host, 10000); |
| } |
| |
| static void |
| mmc_omap_end_of_data(struct mmc_omap_host *host, struct mmc_data *data) |
| { |
| unsigned long flags; |
| int done; |
| |
| if (!host->dma_in_use) { |
| mmc_omap_xfer_done(host, data); |
| return; |
| } |
| done = 0; |
| spin_lock_irqsave(&host->dma_lock, flags); |
| if (host->dma_done) |
| done = 1; |
| else |
| host->brs_received = 1; |
| spin_unlock_irqrestore(&host->dma_lock, flags); |
| if (done) |
| mmc_omap_xfer_done(host, data); |
| } |
| |
| static void |
| mmc_omap_dma_done(struct mmc_omap_host *host, struct mmc_data *data) |
| { |
| unsigned long flags; |
| int done; |
| |
| done = 0; |
| spin_lock_irqsave(&host->dma_lock, flags); |
| if (host->brs_received) |
| done = 1; |
| else |
| host->dma_done = 1; |
| spin_unlock_irqrestore(&host->dma_lock, flags); |
| if (done) |
| mmc_omap_xfer_done(host, data); |
| } |
| |
| static void |
| mmc_omap_cmd_done(struct mmc_omap_host *host, struct mmc_command *cmd) |
| { |
| host->cmd = NULL; |
| |
| del_timer(&host->cmd_abort_timer); |
| |
| if (cmd->flags & MMC_RSP_PRESENT) { |
| if (cmd->flags & MMC_RSP_136) { |
| /* response type 2 */ |
| cmd->resp[3] = |
| OMAP_MMC_READ(host, RSP0) | |
| (OMAP_MMC_READ(host, RSP1) << 16); |
| cmd->resp[2] = |
| OMAP_MMC_READ(host, RSP2) | |
| (OMAP_MMC_READ(host, RSP3) << 16); |
| cmd->resp[1] = |
| OMAP_MMC_READ(host, RSP4) | |
| (OMAP_MMC_READ(host, RSP5) << 16); |
| cmd->resp[0] = |
| OMAP_MMC_READ(host, RSP6) | |
| (OMAP_MMC_READ(host, RSP7) << 16); |
| } else { |
| /* response types 1, 1b, 3, 4, 5, 6 */ |
| cmd->resp[0] = |
| OMAP_MMC_READ(host, RSP6) | |
| (OMAP_MMC_READ(host, RSP7) << 16); |
| } |
| } |
| |
| if (host->data == NULL || cmd->error) { |
| struct mmc_host *mmc; |
| |
| if (host->data != NULL) |
| mmc_omap_abort_xfer(host, host->data); |
| host->mrq = NULL; |
| mmc = host->mmc; |
| mmc_omap_release_slot(host->current_slot, 1); |
| mmc_request_done(mmc, cmd->mrq); |
| } |
| } |
| |
| /* |
| * Abort stuck command. Can occur when card is removed while it is being |
| * read. |
| */ |
| static void mmc_omap_abort_command(struct work_struct *work) |
| { |
| struct mmc_omap_host *host = container_of(work, struct mmc_omap_host, |
| cmd_abort_work); |
| BUG_ON(!host->cmd); |
| |
| dev_dbg(mmc_dev(host->mmc), "Aborting stuck command CMD%d\n", |
| host->cmd->opcode); |
| |
| if (host->cmd->error == 0) |
| host->cmd->error = -ETIMEDOUT; |
| |
| if (host->data == NULL) { |
| struct mmc_command *cmd; |
| struct mmc_host *mmc; |
| |
| cmd = host->cmd; |
| host->cmd = NULL; |
| mmc_omap_send_abort(host, 10000); |
| |
| host->mrq = NULL; |
| mmc = host->mmc; |
| mmc_omap_release_slot(host->current_slot, 1); |
| mmc_request_done(mmc, cmd->mrq); |
| } else |
| mmc_omap_cmd_done(host, host->cmd); |
| |
| host->abort = 0; |
| enable_irq(host->irq); |
| } |
| |
| static void |
| mmc_omap_cmd_timer(struct timer_list *t) |
| { |
| struct mmc_omap_host *host = from_timer(host, t, cmd_abort_timer); |
| unsigned long flags; |
| |
| spin_lock_irqsave(&host->slot_lock, flags); |
| if (host->cmd != NULL && !host->abort) { |
| OMAP_MMC_WRITE(host, IE, 0); |
| disable_irq(host->irq); |
| host->abort = 1; |
| queue_work(host->mmc_omap_wq, &host->cmd_abort_work); |
| } |
| spin_unlock_irqrestore(&host->slot_lock, flags); |
| } |
| |
| /* PIO only */ |
| static void |
| mmc_omap_sg_to_buf(struct mmc_omap_host *host) |
| { |
| struct scatterlist *sg; |
| |
| sg = host->data->sg + host->sg_idx; |
| host->buffer_bytes_left = sg->length; |
| host->buffer = sg_virt(sg); |
| if (host->buffer_bytes_left > host->total_bytes_left) |
| host->buffer_bytes_left = host->total_bytes_left; |
| } |
| |
| static void |
| mmc_omap_clk_timer(struct timer_list *t) |
| { |
| struct mmc_omap_host *host = from_timer(host, t, clk_timer); |
| |
| mmc_omap_fclk_enable(host, 0); |
| } |
| |
| /* PIO only */ |
| static void |
| mmc_omap_xfer_data(struct mmc_omap_host *host, int write) |
| { |
| int n, nwords; |
| |
| if (host->buffer_bytes_left == 0) { |
| host->sg_idx++; |
| BUG_ON(host->sg_idx == host->sg_len); |
| mmc_omap_sg_to_buf(host); |
| } |
| n = 64; |
| if (n > host->buffer_bytes_left) |
| n = host->buffer_bytes_left; |
| |
| /* Round up to handle odd number of bytes to transfer */ |
| nwords = DIV_ROUND_UP(n, 2); |
| |
| host->buffer_bytes_left -= n; |
| host->total_bytes_left -= n; |
| host->data->bytes_xfered += n; |
| |
| if (write) { |
| __raw_writesw(host->virt_base + OMAP_MMC_REG(host, DATA), |
| host->buffer, nwords); |
| } else { |
| __raw_readsw(host->virt_base + OMAP_MMC_REG(host, DATA), |
| host->buffer, nwords); |
| } |
| |
| host->buffer += nwords; |
| } |
| |
| #ifdef CONFIG_MMC_DEBUG |
| static void mmc_omap_report_irq(struct mmc_omap_host *host, u16 status) |
| { |
| static const char *mmc_omap_status_bits[] = { |
| "EOC", "CD", "CB", "BRS", "EOFB", "DTO", "DCRC", "CTO", |
| "CCRC", "CRW", "AF", "AE", "OCRB", "CIRQ", "CERR" |
| }; |
| int i; |
| char res[64], *buf = res; |
| |
| buf += sprintf(buf, "MMC IRQ 0x%x:", status); |
| |
| for (i = 0; i < ARRAY_SIZE(mmc_omap_status_bits); i++) |
| if (status & (1 << i)) |
| buf += sprintf(buf, " %s", mmc_omap_status_bits[i]); |
| dev_vdbg(mmc_dev(host->mmc), "%s\n", res); |
| } |
| #else |
| static void mmc_omap_report_irq(struct mmc_omap_host *host, u16 status) |
| { |
| } |
| #endif |
| |
| |
| static irqreturn_t mmc_omap_irq(int irq, void *dev_id) |
| { |
| struct mmc_omap_host * host = (struct mmc_omap_host *)dev_id; |
| u16 status; |
| int end_command; |
| int end_transfer; |
| int transfer_error, cmd_error; |
| |
| if (host->cmd == NULL && host->data == NULL) { |
| status = OMAP_MMC_READ(host, STAT); |
| dev_info(mmc_dev(host->slots[0]->mmc), |
| "Spurious IRQ 0x%04x\n", status); |
| if (status != 0) { |
| OMAP_MMC_WRITE(host, STAT, status); |
| OMAP_MMC_WRITE(host, IE, 0); |
| } |
| return IRQ_HANDLED; |
| } |
| |
| end_command = 0; |
| end_transfer = 0; |
| transfer_error = 0; |
| cmd_error = 0; |
| |
| while ((status = OMAP_MMC_READ(host, STAT)) != 0) { |
| int cmd; |
| |
| OMAP_MMC_WRITE(host, STAT, status); |
| if (host->cmd != NULL) |
| cmd = host->cmd->opcode; |
| else |
| cmd = -1; |
| dev_dbg(mmc_dev(host->mmc), "MMC IRQ %04x (CMD %d): ", |
| status, cmd); |
| mmc_omap_report_irq(host, status); |
| |
| if (host->total_bytes_left) { |
| if ((status & OMAP_MMC_STAT_A_FULL) || |
| (status & OMAP_MMC_STAT_END_OF_DATA)) |
| mmc_omap_xfer_data(host, 0); |
| if (status & OMAP_MMC_STAT_A_EMPTY) |
| mmc_omap_xfer_data(host, 1); |
| } |
| |
| if (status & OMAP_MMC_STAT_END_OF_DATA) |
| end_transfer = 1; |
| |
| if (status & OMAP_MMC_STAT_DATA_TOUT) { |
| dev_dbg(mmc_dev(host->mmc), "data timeout (CMD%d)\n", |
| cmd); |
| if (host->data) { |
| host->data->error = -ETIMEDOUT; |
| transfer_error = 1; |
| } |
| } |
| |
| if (status & OMAP_MMC_STAT_DATA_CRC) { |
| if (host->data) { |
| host->data->error = -EILSEQ; |
| dev_dbg(mmc_dev(host->mmc), |
| "data CRC error, bytes left %d\n", |
| host->total_bytes_left); |
| transfer_error = 1; |
| } else { |
| dev_dbg(mmc_dev(host->mmc), "data CRC error\n"); |
| } |
| } |
| |
| if (status & OMAP_MMC_STAT_CMD_TOUT) { |
| /* Timeouts are routine with some commands */ |
| if (host->cmd) { |
| struct mmc_omap_slot *slot = |
| host->current_slot; |
| if (slot == NULL || |
| !mmc_omap_cover_is_open(slot)) |
| dev_err(mmc_dev(host->mmc), |
| "command timeout (CMD%d)\n", |
| cmd); |
| host->cmd->error = -ETIMEDOUT; |
| end_command = 1; |
| cmd_error = 1; |
| } |
| } |
| |
| if (status & OMAP_MMC_STAT_CMD_CRC) { |
| if (host->cmd) { |
| dev_err(mmc_dev(host->mmc), |
| "command CRC error (CMD%d, arg 0x%08x)\n", |
| cmd, host->cmd->arg); |
| host->cmd->error = -EILSEQ; |
| end_command = 1; |
| cmd_error = 1; |
| } else |
| dev_err(mmc_dev(host->mmc), |
| "command CRC error without cmd?\n"); |
| } |
| |
| if (status & OMAP_MMC_STAT_CARD_ERR) { |
| dev_dbg(mmc_dev(host->mmc), |
| "ignoring card status error (CMD%d)\n", |
| cmd); |
| end_command = 1; |
| } |
| |
| /* |
| * NOTE: On 1610 the END_OF_CMD may come too early when |
| * starting a write |
| */ |
| if ((status & OMAP_MMC_STAT_END_OF_CMD) && |
| (!(status & OMAP_MMC_STAT_A_EMPTY))) { |
| end_command = 1; |
| } |
| } |
| |
| if (cmd_error && host->data) { |
| del_timer(&host->cmd_abort_timer); |
| host->abort = 1; |
| OMAP_MMC_WRITE(host, IE, 0); |
| disable_irq_nosync(host->irq); |
| queue_work(host->mmc_omap_wq, &host->cmd_abort_work); |
| return IRQ_HANDLED; |
| } |
| |
| if (end_command && host->cmd) |
| mmc_omap_cmd_done(host, host->cmd); |
| if (host->data != NULL) { |
| if (transfer_error) |
| mmc_omap_xfer_done(host, host->data); |
| else if (end_transfer) |
| mmc_omap_end_of_data(host, host->data); |
| } |
| |
| return IRQ_HANDLED; |
| } |
| |
| void omap_mmc_notify_cover_event(struct device *dev, int num, int is_closed) |
| { |
| int cover_open; |
| struct mmc_omap_host *host = dev_get_drvdata(dev); |
| struct mmc_omap_slot *slot = host->slots[num]; |
| |
| BUG_ON(num >= host->nr_slots); |
| |
| /* Other subsystems can call in here before we're initialised. */ |
| if (host->nr_slots == 0 || !host->slots[num]) |
| return; |
| |
| cover_open = mmc_omap_cover_is_open(slot); |
| if (cover_open != slot->cover_open) { |
| slot->cover_open = cover_open; |
| sysfs_notify(&slot->mmc->class_dev.kobj, NULL, "cover_switch"); |
| } |
| |
| tasklet_hi_schedule(&slot->cover_tasklet); |
| } |
| |
| static void mmc_omap_cover_timer(struct timer_list *t) |
| { |
| struct mmc_omap_slot *slot = from_timer(slot, t, cover_timer); |
| tasklet_schedule(&slot->cover_tasklet); |
| } |
| |
| static void mmc_omap_cover_handler(struct tasklet_struct *t) |
| { |
| struct mmc_omap_slot *slot = from_tasklet(slot, t, cover_tasklet); |
| int cover_open = mmc_omap_cover_is_open(slot); |
| |
| mmc_detect_change(slot->mmc, 0); |
| if (!cover_open) |
| return; |
| |
| /* |
| * If no card is inserted, we postpone polling until |
| * the cover has been closed. |
| */ |
| if (slot->mmc->card == NULL) |
| return; |
| |
| mod_timer(&slot->cover_timer, |
| jiffies + msecs_to_jiffies(OMAP_MMC_COVER_POLL_DELAY)); |
| } |
| |
| static void mmc_omap_dma_callback(void *priv) |
| { |
| struct mmc_omap_host *host = priv; |
| struct mmc_data *data = host->data; |
| |
| /* If we got to the end of DMA, assume everything went well */ |
| data->bytes_xfered += data->blocks * data->blksz; |
| |
| mmc_omap_dma_done(host, data); |
| } |
| |
| static inline void set_cmd_timeout(struct mmc_omap_host *host, struct mmc_request *req) |
| { |
| u16 reg; |
| |
| reg = OMAP_MMC_READ(host, SDIO); |
| reg &= ~(1 << 5); |
| OMAP_MMC_WRITE(host, SDIO, reg); |
| /* Set maximum timeout */ |
| OMAP_MMC_WRITE(host, CTO, 0xfd); |
| } |
| |
| static inline void set_data_timeout(struct mmc_omap_host *host, struct mmc_request *req) |
| { |
| unsigned int timeout, cycle_ns; |
| u16 reg; |
| |
| cycle_ns = 1000000000 / host->current_slot->fclk_freq; |
| timeout = req->data->timeout_ns / cycle_ns; |
| timeout += req->data->timeout_clks; |
| |
| /* Check if we need to use timeout multiplier register */ |
| reg = OMAP_MMC_READ(host, SDIO); |
| if (timeout > 0xffff) { |
| reg |= (1 << 5); |
| timeout /= 1024; |
| } else |
| reg &= ~(1 << 5); |
| OMAP_MMC_WRITE(host, SDIO, reg); |
| OMAP_MMC_WRITE(host, DTO, timeout); |
| } |
| |
| static void |
| mmc_omap_prepare_data(struct mmc_omap_host *host, struct mmc_request *req) |
| { |
| struct mmc_data *data = req->data; |
| int i, use_dma = 1, block_size; |
| struct scatterlist *sg; |
| unsigned sg_len; |
| |
| host->data = data; |
| if (data == NULL) { |
| OMAP_MMC_WRITE(host, BLEN, 0); |
| OMAP_MMC_WRITE(host, NBLK, 0); |
| OMAP_MMC_WRITE(host, BUF, 0); |
| host->dma_in_use = 0; |
| set_cmd_timeout(host, req); |
| return; |
| } |
| |
| block_size = data->blksz; |
| |
| OMAP_MMC_WRITE(host, NBLK, data->blocks - 1); |
| OMAP_MMC_WRITE(host, BLEN, block_size - 1); |
| set_data_timeout(host, req); |
| |
| /* cope with calling layer confusion; it issues "single |
| * block" writes using multi-block scatterlists. |
| */ |
| sg_len = (data->blocks == 1) ? 1 : data->sg_len; |
| |
| /* Only do DMA for entire blocks */ |
| for_each_sg(data->sg, sg, sg_len, i) { |
| if ((sg->length % block_size) != 0) { |
| use_dma = 0; |
| break; |
| } |
| } |
| |
| host->sg_idx = 0; |
| if (use_dma) { |
| enum dma_data_direction dma_data_dir; |
| struct dma_async_tx_descriptor *tx; |
| struct dma_chan *c; |
| u32 burst, *bp; |
| u16 buf; |
| |
| /* |
| * FIFO is 16x2 bytes on 15xx, and 32x2 bytes on 16xx |
| * and 24xx. Use 16 or 32 word frames when the |
| * blocksize is at least that large. Blocksize is |
| * usually 512 bytes; but not for some SD reads. |
| */ |
| burst = mmc_omap15xx() ? 32 : 64; |
| if (burst > data->blksz) |
| burst = data->blksz; |
| |
| burst >>= 1; |
| |
| if (data->flags & MMC_DATA_WRITE) { |
| c = host->dma_tx; |
| bp = &host->dma_tx_burst; |
| buf = 0x0f80 | (burst - 1) << 0; |
| dma_data_dir = DMA_TO_DEVICE; |
| } else { |
| c = host->dma_rx; |
| bp = &host->dma_rx_burst; |
| buf = 0x800f | (burst - 1) << 8; |
| dma_data_dir = DMA_FROM_DEVICE; |
| } |
| |
| if (!c) |
| goto use_pio; |
| |
| /* Only reconfigure if we have a different burst size */ |
| if (*bp != burst) { |
| struct dma_slave_config cfg = { |
| .src_addr = host->phys_base + |
| OMAP_MMC_REG(host, DATA), |
| .dst_addr = host->phys_base + |
| OMAP_MMC_REG(host, DATA), |
| .src_addr_width = DMA_SLAVE_BUSWIDTH_2_BYTES, |
| .dst_addr_width = DMA_SLAVE_BUSWIDTH_2_BYTES, |
| .src_maxburst = burst, |
| .dst_maxburst = burst, |
| }; |
| |
| if (dmaengine_slave_config(c, &cfg)) |
| goto use_pio; |
| |
| *bp = burst; |
| } |
| |
| host->sg_len = dma_map_sg(c->device->dev, data->sg, sg_len, |
| dma_data_dir); |
| if (host->sg_len == 0) |
| goto use_pio; |
| |
| tx = dmaengine_prep_slave_sg(c, data->sg, host->sg_len, |
| data->flags & MMC_DATA_WRITE ? DMA_MEM_TO_DEV : DMA_DEV_TO_MEM, |
| DMA_PREP_INTERRUPT | DMA_CTRL_ACK); |
| if (!tx) |
| goto use_pio; |
| |
| OMAP_MMC_WRITE(host, BUF, buf); |
| |
| tx->callback = mmc_omap_dma_callback; |
| tx->callback_param = host; |
| dmaengine_submit(tx); |
| host->brs_received = 0; |
| host->dma_done = 0; |
| host->dma_in_use = 1; |
| return; |
| } |
| use_pio: |
| |
| /* Revert to PIO? */ |
| OMAP_MMC_WRITE(host, BUF, 0x1f1f); |
| host->total_bytes_left = data->blocks * block_size; |
| host->sg_len = sg_len; |
| mmc_omap_sg_to_buf(host); |
| host->dma_in_use = 0; |
| } |
| |
| static void mmc_omap_start_request(struct mmc_omap_host *host, |
| struct mmc_request *req) |
| { |
| BUG_ON(host->mrq != NULL); |
| |
| host->mrq = req; |
| |
| /* only touch fifo AFTER the controller readies it */ |
| mmc_omap_prepare_data(host, req); |
| mmc_omap_start_command(host, req->cmd); |
| if (host->dma_in_use) { |
| struct dma_chan *c = host->data->flags & MMC_DATA_WRITE ? |
| host->dma_tx : host->dma_rx; |
| |
| dma_async_issue_pending(c); |
| } |
| } |
| |
| static void mmc_omap_request(struct mmc_host *mmc, struct mmc_request *req) |
| { |
| struct mmc_omap_slot *slot = mmc_priv(mmc); |
| struct mmc_omap_host *host = slot->host; |
| unsigned long flags; |
| |
| spin_lock_irqsave(&host->slot_lock, flags); |
| if (host->mmc != NULL) { |
| BUG_ON(slot->mrq != NULL); |
| slot->mrq = req; |
| spin_unlock_irqrestore(&host->slot_lock, flags); |
| return; |
| } else |
| host->mmc = mmc; |
| spin_unlock_irqrestore(&host->slot_lock, flags); |
| mmc_omap_select_slot(slot, 1); |
| mmc_omap_start_request(host, req); |
| } |
| |
| static void mmc_omap_set_power(struct mmc_omap_slot *slot, int power_on, |
| int vdd) |
| { |
| struct mmc_omap_host *host; |
| |
| host = slot->host; |
| |
| if (slot->vsd) |
| gpiod_set_value(slot->vsd, power_on); |
| if (slot->vio) |
| gpiod_set_value(slot->vio, power_on); |
| |
| if (slot->pdata->set_power != NULL) |
| slot->pdata->set_power(mmc_dev(slot->mmc), slot->id, power_on, |
| vdd); |
| if (mmc_omap2()) { |
| u16 w; |
| |
| if (power_on) { |
| w = OMAP_MMC_READ(host, CON); |
| OMAP_MMC_WRITE(host, CON, w | (1 << 11)); |
| } else { |
| w = OMAP_MMC_READ(host, CON); |
| OMAP_MMC_WRITE(host, CON, w & ~(1 << 11)); |
| } |
| } |
| } |
| |
| static int mmc_omap_calc_divisor(struct mmc_host *mmc, struct mmc_ios *ios) |
| { |
| struct mmc_omap_slot *slot = mmc_priv(mmc); |
| struct mmc_omap_host *host = slot->host; |
| int func_clk_rate = clk_get_rate(host->fclk); |
| int dsor; |
| |
| if (ios->clock == 0) |
| return 0; |
| |
| dsor = func_clk_rate / ios->clock; |
| if (dsor < 1) |
| dsor = 1; |
| |
| if (func_clk_rate / dsor > ios->clock) |
| dsor++; |
| |
| if (dsor > 250) |
| dsor = 250; |
| |
| slot->fclk_freq = func_clk_rate / dsor; |
| |
| if (ios->bus_width == MMC_BUS_WIDTH_4) |
| dsor |= 1 << 15; |
| |
| return dsor; |
| } |
| |
| static void mmc_omap_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) |
| { |
| struct mmc_omap_slot *slot = mmc_priv(mmc); |
| struct mmc_omap_host *host = slot->host; |
| int i, dsor; |
| int clk_enabled, init_stream; |
| |
| mmc_omap_select_slot(slot, 0); |
| |
| dsor = mmc_omap_calc_divisor(mmc, ios); |
| |
| if (ios->vdd != slot->vdd) |
| slot->vdd = ios->vdd; |
| |
| clk_enabled = 0; |
| init_stream = 0; |
| switch (ios->power_mode) { |
| case MMC_POWER_OFF: |
| mmc_omap_set_power(slot, 0, ios->vdd); |
| break; |
| case MMC_POWER_UP: |
| /* Cannot touch dsor yet, just power up MMC */ |
| mmc_omap_set_power(slot, 1, ios->vdd); |
| slot->power_mode = ios->power_mode; |
| goto exit; |
| case MMC_POWER_ON: |
| mmc_omap_fclk_enable(host, 1); |
| clk_enabled = 1; |
| dsor |= 1 << 11; |
| if (slot->power_mode != MMC_POWER_ON) |
| init_stream = 1; |
| break; |
| } |
| slot->power_mode = ios->power_mode; |
| |
| if (slot->bus_mode != ios->bus_mode) { |
| if (slot->pdata->set_bus_mode != NULL) |
| slot->pdata->set_bus_mode(mmc_dev(mmc), slot->id, |
| ios->bus_mode); |
| slot->bus_mode = ios->bus_mode; |
| } |
| |
| /* On insanely high arm_per frequencies something sometimes |
| * goes somehow out of sync, and the POW bit is not being set, |
| * which results in the while loop below getting stuck. |
| * Writing to the CON register twice seems to do the trick. */ |
| for (i = 0; i < 2; i++) |
| OMAP_MMC_WRITE(host, CON, dsor); |
| slot->saved_con = dsor; |
| if (init_stream) { |
| /* worst case at 400kHz, 80 cycles makes 200 microsecs */ |
| int usecs = 250; |
| |
| /* Send clock cycles, poll completion */ |
| OMAP_MMC_WRITE(host, IE, 0); |
| OMAP_MMC_WRITE(host, STAT, 0xffff); |
| OMAP_MMC_WRITE(host, CMD, 1 << 7); |
| while (usecs > 0 && (OMAP_MMC_READ(host, STAT) & 1) == 0) { |
| udelay(1); |
| usecs--; |
| } |
| OMAP_MMC_WRITE(host, STAT, 1); |
| } |
| |
| exit: |
| mmc_omap_release_slot(slot, clk_enabled); |
| } |
| |
| static const struct mmc_host_ops mmc_omap_ops = { |
| .request = mmc_omap_request, |
| .set_ios = mmc_omap_set_ios, |
| }; |
| |
| static int mmc_omap_new_slot(struct mmc_omap_host *host, int id) |
| { |
| struct mmc_omap_slot *slot = NULL; |
| struct mmc_host *mmc; |
| int r; |
| |
| mmc = mmc_alloc_host(sizeof(struct mmc_omap_slot), host->dev); |
| if (mmc == NULL) |
| return -ENOMEM; |
| |
| slot = mmc_priv(mmc); |
| slot->host = host; |
| slot->mmc = mmc; |
| slot->id = id; |
| slot->power_mode = MMC_POWER_UNDEFINED; |
| slot->pdata = &host->pdata->slots[id]; |
| |
| /* Check for some optional GPIO controls */ |
| slot->vsd = gpiod_get_index_optional(host->dev, "vsd", |
| id, GPIOD_OUT_LOW); |
| if (IS_ERR(slot->vsd)) |
| return dev_err_probe(host->dev, PTR_ERR(slot->vsd), |
| "error looking up VSD GPIO\n"); |
| slot->vio = gpiod_get_index_optional(host->dev, "vio", |
| id, GPIOD_OUT_LOW); |
| if (IS_ERR(slot->vio)) |
| return dev_err_probe(host->dev, PTR_ERR(slot->vio), |
| "error looking up VIO GPIO\n"); |
| slot->cover = gpiod_get_index_optional(host->dev, "cover", |
| id, GPIOD_IN); |
| if (IS_ERR(slot->cover)) |
| return dev_err_probe(host->dev, PTR_ERR(slot->cover), |
| "error looking up cover switch GPIO\n"); |
| |
| host->slots[id] = slot; |
| |
| mmc->caps = 0; |
| if (host->pdata->slots[id].wires >= 4) |
| mmc->caps |= MMC_CAP_4_BIT_DATA; |
| |
| mmc->ops = &mmc_omap_ops; |
| mmc->f_min = 400000; |
| |
| if (mmc_omap2()) |
| mmc->f_max = 48000000; |
| else |
| mmc->f_max = 24000000; |
| if (host->pdata->max_freq) |
| mmc->f_max = min(host->pdata->max_freq, mmc->f_max); |
| mmc->ocr_avail = slot->pdata->ocr_mask; |
| |
| /* Use scatterlist DMA to reduce per-transfer costs. |
| * NOTE max_seg_size assumption that small blocks aren't |
| * normally used (except e.g. for reading SD registers). |
| */ |
| mmc->max_segs = 32; |
| mmc->max_blk_size = 2048; /* BLEN is 11 bits (+1) */ |
| mmc->max_blk_count = 2048; /* NBLK is 11 bits (+1) */ |
| mmc->max_req_size = mmc->max_blk_size * mmc->max_blk_count; |
| mmc->max_seg_size = mmc->max_req_size; |
| |
| if (slot->pdata->get_cover_state != NULL) { |
| timer_setup(&slot->cover_timer, mmc_omap_cover_timer, 0); |
| tasklet_setup(&slot->cover_tasklet, mmc_omap_cover_handler); |
| } |
| |
| r = mmc_add_host(mmc); |
| if (r < 0) |
| goto err_remove_host; |
| |
| if (slot->pdata->name != NULL) { |
| r = device_create_file(&mmc->class_dev, |
| &dev_attr_slot_name); |
| if (r < 0) |
| goto err_remove_host; |
| } |
| |
| if (slot->pdata->get_cover_state != NULL) { |
| r = device_create_file(&mmc->class_dev, |
| &dev_attr_cover_switch); |
| if (r < 0) |
| goto err_remove_slot_name; |
| tasklet_schedule(&slot->cover_tasklet); |
| } |
| |
| return 0; |
| |
| err_remove_slot_name: |
| if (slot->pdata->name != NULL) |
| device_remove_file(&mmc->class_dev, &dev_attr_slot_name); |
| err_remove_host: |
| mmc_remove_host(mmc); |
| mmc_free_host(mmc); |
| return r; |
| } |
| |
| static void mmc_omap_remove_slot(struct mmc_omap_slot *slot) |
| { |
| struct mmc_host *mmc = slot->mmc; |
| |
| if (slot->pdata->name != NULL) |
| device_remove_file(&mmc->class_dev, &dev_attr_slot_name); |
| if (slot->pdata->get_cover_state != NULL) |
| device_remove_file(&mmc->class_dev, &dev_attr_cover_switch); |
| |
| tasklet_kill(&slot->cover_tasklet); |
| del_timer_sync(&slot->cover_timer); |
| flush_workqueue(slot->host->mmc_omap_wq); |
| |
| mmc_remove_host(mmc); |
| mmc_free_host(mmc); |
| } |
| |
| static int mmc_omap_probe(struct platform_device *pdev) |
| { |
| struct omap_mmc_platform_data *pdata = pdev->dev.platform_data; |
| struct mmc_omap_host *host = NULL; |
| struct resource *res; |
| int i, ret = 0; |
| int irq; |
| |
| if (pdata == NULL) { |
| dev_err(&pdev->dev, "platform data missing\n"); |
| return -ENXIO; |
| } |
| if (pdata->nr_slots == 0) { |
| dev_err(&pdev->dev, "no slots\n"); |
| return -EPROBE_DEFER; |
| } |
| |
| host = devm_kzalloc(&pdev->dev, sizeof(struct mmc_omap_host), |
| GFP_KERNEL); |
| if (host == NULL) |
| return -ENOMEM; |
| |
| irq = platform_get_irq(pdev, 0); |
| if (irq < 0) |
| return irq; |
| |
| host->virt_base = devm_platform_get_and_ioremap_resource(pdev, 0, &res); |
| if (IS_ERR(host->virt_base)) |
| return PTR_ERR(host->virt_base); |
| |
| host->slot_switch = gpiod_get_optional(host->dev, "switch", |
| GPIOD_OUT_LOW); |
| if (IS_ERR(host->slot_switch)) |
| return dev_err_probe(host->dev, PTR_ERR(host->slot_switch), |
| "error looking up slot switch GPIO\n"); |
| |
| |
| INIT_WORK(&host->slot_release_work, mmc_omap_slot_release_work); |
| INIT_WORK(&host->send_stop_work, mmc_omap_send_stop_work); |
| |
| INIT_WORK(&host->cmd_abort_work, mmc_omap_abort_command); |
| timer_setup(&host->cmd_abort_timer, mmc_omap_cmd_timer, 0); |
| |
| spin_lock_init(&host->clk_lock); |
| timer_setup(&host->clk_timer, mmc_omap_clk_timer, 0); |
| |
| spin_lock_init(&host->dma_lock); |
| spin_lock_init(&host->slot_lock); |
| init_waitqueue_head(&host->slot_wq); |
| |
| host->pdata = pdata; |
| host->features = host->pdata->slots[0].features; |
| host->dev = &pdev->dev; |
| platform_set_drvdata(pdev, host); |
| |
| host->id = pdev->id; |
| host->irq = irq; |
| host->phys_base = res->start; |
| host->iclk = clk_get(&pdev->dev, "ick"); |
| if (IS_ERR(host->iclk)) |
| return PTR_ERR(host->iclk); |
| clk_prepare_enable(host->iclk); |
| |
| host->fclk = clk_get(&pdev->dev, "fck"); |
| if (IS_ERR(host->fclk)) { |
| ret = PTR_ERR(host->fclk); |
| goto err_free_iclk; |
| } |
| |
| ret = clk_prepare(host->fclk); |
| if (ret) |
| goto err_put_fclk; |
| |
| host->dma_tx_burst = -1; |
| host->dma_rx_burst = -1; |
| |
| host->dma_tx = dma_request_chan(&pdev->dev, "tx"); |
| if (IS_ERR(host->dma_tx)) { |
| ret = PTR_ERR(host->dma_tx); |
| if (ret == -EPROBE_DEFER) |
| goto err_free_fclk; |
| |
| host->dma_tx = NULL; |
| dev_warn(host->dev, "TX DMA channel request failed\n"); |
| } |
| |
| host->dma_rx = dma_request_chan(&pdev->dev, "rx"); |
| if (IS_ERR(host->dma_rx)) { |
| ret = PTR_ERR(host->dma_rx); |
| if (ret == -EPROBE_DEFER) { |
| if (host->dma_tx) |
| dma_release_channel(host->dma_tx); |
| goto err_free_fclk; |
| } |
| |
| host->dma_rx = NULL; |
| dev_warn(host->dev, "RX DMA channel request failed\n"); |
| } |
| |
| ret = request_irq(host->irq, mmc_omap_irq, 0, DRIVER_NAME, host); |
| if (ret) |
| goto err_free_dma; |
| |
| if (pdata->init != NULL) { |
| ret = pdata->init(&pdev->dev); |
| if (ret < 0) |
| goto err_free_irq; |
| } |
| |
| host->nr_slots = pdata->nr_slots; |
| host->reg_shift = (mmc_omap7xx() ? 1 : 2); |
| |
| host->mmc_omap_wq = alloc_workqueue("mmc_omap", 0, 0); |
| if (!host->mmc_omap_wq) { |
| ret = -ENOMEM; |
| goto err_plat_cleanup; |
| } |
| |
| for (i = 0; i < pdata->nr_slots; i++) { |
| ret = mmc_omap_new_slot(host, i); |
| if (ret < 0) { |
| while (--i >= 0) |
| mmc_omap_remove_slot(host->slots[i]); |
| |
| goto err_destroy_wq; |
| } |
| } |
| |
| return 0; |
| |
| err_destroy_wq: |
| destroy_workqueue(host->mmc_omap_wq); |
| err_plat_cleanup: |
| if (pdata->cleanup) |
| pdata->cleanup(&pdev->dev); |
| err_free_irq: |
| free_irq(host->irq, host); |
| err_free_dma: |
| if (host->dma_tx) |
| dma_release_channel(host->dma_tx); |
| if (host->dma_rx) |
| dma_release_channel(host->dma_rx); |
| err_free_fclk: |
| clk_unprepare(host->fclk); |
| err_put_fclk: |
| clk_put(host->fclk); |
| err_free_iclk: |
| clk_disable_unprepare(host->iclk); |
| clk_put(host->iclk); |
| return ret; |
| } |
| |
| static void mmc_omap_remove(struct platform_device *pdev) |
| { |
| struct mmc_omap_host *host = platform_get_drvdata(pdev); |
| int i; |
| |
| BUG_ON(host == NULL); |
| |
| for (i = 0; i < host->nr_slots; i++) |
| mmc_omap_remove_slot(host->slots[i]); |
| |
| if (host->pdata->cleanup) |
| host->pdata->cleanup(&pdev->dev); |
| |
| mmc_omap_fclk_enable(host, 0); |
| free_irq(host->irq, host); |
| clk_unprepare(host->fclk); |
| clk_put(host->fclk); |
| clk_disable_unprepare(host->iclk); |
| clk_put(host->iclk); |
| |
| if (host->dma_tx) |
| dma_release_channel(host->dma_tx); |
| if (host->dma_rx) |
| dma_release_channel(host->dma_rx); |
| |
| destroy_workqueue(host->mmc_omap_wq); |
| } |
| |
| #if IS_BUILTIN(CONFIG_OF) |
| static const struct of_device_id mmc_omap_match[] = { |
| { .compatible = "ti,omap2420-mmc", }, |
| { }, |
| }; |
| MODULE_DEVICE_TABLE(of, mmc_omap_match); |
| #endif |
| |
| static struct platform_driver mmc_omap_driver = { |
| .probe = mmc_omap_probe, |
| .remove_new = mmc_omap_remove, |
| .driver = { |
| .name = DRIVER_NAME, |
| .probe_type = PROBE_PREFER_ASYNCHRONOUS, |
| .of_match_table = of_match_ptr(mmc_omap_match), |
| }, |
| }; |
| |
| module_platform_driver(mmc_omap_driver); |
| MODULE_DESCRIPTION("OMAP Multimedia Card driver"); |
| MODULE_LICENSE("GPL"); |
| MODULE_ALIAS("platform:" DRIVER_NAME); |
| MODULE_AUTHOR("Juha Yrjölä"); |