blob: 8c73f67c43cabec2112ed7c4346b878bcb5208f6 [file] [log] [blame]
* Qualcomm Atheros QCA8xxx switch family
Required properties:
- compatible: should be one of:
"qca,qca8327"
"qca,qca8334"
"qca,qca8337"
- #size-cells: must be 0
- #address-cells: must be 1
Optional properties:
- reset-gpios: GPIO to be used to reset the whole device
Subnodes:
The integrated switch subnode should be specified according to the binding
described in dsa/dsa.txt. If the QCA8K switch is connect to a SoC's external
mdio-bus each subnode describing a port needs to have a valid phandle
referencing the internal PHY it is connected to. This is because there's no
N:N mapping of port and PHY id.
To declare the internal mdio-bus configuration, declare a mdio node in the
switch node and declare the phandle for the port referencing the internal
PHY is connected to. In this config a internal mdio-bus is registered and
the mdio MASTER is used as communication.
Don't use mixed external and internal mdio-bus configurations, as this is
not supported by the hardware.
The CPU port of this switch is always port 0.
A CPU port node has the following optional node:
- fixed-link : Fixed-link subnode describing a link to a non-MDIO
managed entity. See
Documentation/devicetree/bindings/net/fixed-link.txt
for details.
For QCA8K the 'fixed-link' sub-node supports only the following properties:
- 'speed' (integer, mandatory), to indicate the link speed. Accepted
values are 10, 100 and 1000
- 'full-duplex' (boolean, optional), to indicate that full duplex is
used. When absent, half duplex is assumed.
Examples:
for the external mdio-bus configuration:
&mdio0 {
phy_port1: phy@0 {
reg = <0>;
};
phy_port2: phy@1 {
reg = <1>;
};
phy_port3: phy@2 {
reg = <2>;
};
phy_port4: phy@3 {
reg = <3>;
};
phy_port5: phy@4 {
reg = <4>;
};
switch@10 {
compatible = "qca,qca8337";
#address-cells = <1>;
#size-cells = <0>;
reset-gpios = <&gpio 42 GPIO_ACTIVE_LOW>;
reg = <0x10>;
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
label = "cpu";
ethernet = <&gmac1>;
phy-mode = "rgmii";
fixed-link {
speed = 1000;
full-duplex;
};
};
port@1 {
reg = <1>;
label = "lan1";
phy-handle = <&phy_port1>;
};
port@2 {
reg = <2>;
label = "lan2";
phy-handle = <&phy_port2>;
};
port@3 {
reg = <3>;
label = "lan3";
phy-handle = <&phy_port3>;
};
port@4 {
reg = <4>;
label = "lan4";
phy-handle = <&phy_port4>;
};
port@5 {
reg = <5>;
label = "wan";
phy-handle = <&phy_port5>;
};
};
};
};
for the internal master mdio-bus configuration:
&mdio0 {
switch@10 {
compatible = "qca,qca8337";
#address-cells = <1>;
#size-cells = <0>;
reset-gpios = <&gpio 42 GPIO_ACTIVE_LOW>;
reg = <0x10>;
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
label = "cpu";
ethernet = <&gmac1>;
phy-mode = "rgmii";
fixed-link {
speed = 1000;
full-duplex;
};
};
port@1 {
reg = <1>;
label = "lan1";
phy-mode = "internal";
phy-handle = <&phy_port1>;
};
port@2 {
reg = <2>;
label = "lan2";
phy-mode = "internal";
phy-handle = <&phy_port2>;
};
port@3 {
reg = <3>;
label = "lan3";
phy-mode = "internal";
phy-handle = <&phy_port3>;
};
port@4 {
reg = <4>;
label = "lan4";
phy-mode = "internal";
phy-handle = <&phy_port4>;
};
port@5 {
reg = <5>;
label = "wan";
phy-mode = "internal";
phy-handle = <&phy_port5>;
};
};
mdio {
#address-cells = <1>;
#size-cells = <0>;
phy_port1: phy@0 {
reg = <0>;
};
phy_port2: phy@1 {
reg = <1>;
};
phy_port3: phy@2 {
reg = <2>;
};
phy_port4: phy@3 {
reg = <3>;
};
phy_port5: phy@4 {
reg = <4>;
};
};
};
};