| // SPDX-License-Identifier: GPL-2.0+ |
| /* Copyright (C) 2009 - 2019 Broadcom */ |
| |
| #include <linux/bitfield.h> |
| #include <linux/bitops.h> |
| #include <linux/clk.h> |
| #include <linux/compiler.h> |
| #include <linux/delay.h> |
| #include <linux/init.h> |
| #include <linux/interrupt.h> |
| #include <linux/io.h> |
| #include <linux/iopoll.h> |
| #include <linux/ioport.h> |
| #include <linux/irqchip/chained_irq.h> |
| #include <linux/irqdomain.h> |
| #include <linux/kernel.h> |
| #include <linux/list.h> |
| #include <linux/log2.h> |
| #include <linux/module.h> |
| #include <linux/msi.h> |
| #include <linux/of_address.h> |
| #include <linux/of_irq.h> |
| #include <linux/of_pci.h> |
| #include <linux/of_platform.h> |
| #include <linux/pci.h> |
| #include <linux/pci-ecam.h> |
| #include <linux/printk.h> |
| #include <linux/regulator/consumer.h> |
| #include <linux/reset.h> |
| #include <linux/sizes.h> |
| #include <linux/slab.h> |
| #include <linux/string.h> |
| #include <linux/types.h> |
| |
| #include "../pci.h" |
| |
| /* BRCM_PCIE_CAP_REGS - Offset for the mandatory capability config regs */ |
| #define BRCM_PCIE_CAP_REGS 0x00ac |
| |
| /* Broadcom STB PCIe Register Offsets */ |
| #define PCIE_RC_CFG_VENDOR_VENDOR_SPECIFIC_REG1 0x0188 |
| #define PCIE_RC_CFG_VENDOR_VENDOR_SPECIFIC_REG1_ENDIAN_MODE_BAR2_MASK 0xc |
| #define PCIE_RC_CFG_VENDOR_SPCIFIC_REG1_LITTLE_ENDIAN 0x0 |
| |
| #define PCIE_RC_CFG_PRIV1_ID_VAL3 0x043c |
| #define PCIE_RC_CFG_PRIV1_ID_VAL3_CLASS_CODE_MASK 0xffffff |
| |
| #define PCIE_RC_CFG_PRIV1_LINK_CAPABILITY 0x04dc |
| #define PCIE_RC_CFG_PRIV1_LINK_CAPABILITY_ASPM_SUPPORT_MASK 0xc00 |
| |
| #define PCIE_RC_DL_MDIO_ADDR 0x1100 |
| #define PCIE_RC_DL_MDIO_WR_DATA 0x1104 |
| #define PCIE_RC_DL_MDIO_RD_DATA 0x1108 |
| |
| #define PCIE_MISC_MISC_CTRL 0x4008 |
| #define PCIE_MISC_MISC_CTRL_PCIE_RCB_64B_MODE_MASK 0x80 |
| #define PCIE_MISC_MISC_CTRL_PCIE_RCB_MPS_MODE_MASK 0x400 |
| #define PCIE_MISC_MISC_CTRL_SCB_ACCESS_EN_MASK 0x1000 |
| #define PCIE_MISC_MISC_CTRL_CFG_READ_UR_MODE_MASK 0x2000 |
| #define PCIE_MISC_MISC_CTRL_MAX_BURST_SIZE_MASK 0x300000 |
| |
| #define PCIE_MISC_MISC_CTRL_SCB0_SIZE_MASK 0xf8000000 |
| #define PCIE_MISC_MISC_CTRL_SCB1_SIZE_MASK 0x07c00000 |
| #define PCIE_MISC_MISC_CTRL_SCB2_SIZE_MASK 0x0000001f |
| #define SCB_SIZE_MASK(x) PCIE_MISC_MISC_CTRL_SCB ## x ## _SIZE_MASK |
| |
| #define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_LO 0x400c |
| #define PCIE_MEM_WIN0_LO(win) \ |
| PCIE_MISC_CPU_2_PCIE_MEM_WIN0_LO + ((win) * 8) |
| |
| #define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_HI 0x4010 |
| #define PCIE_MEM_WIN0_HI(win) \ |
| PCIE_MISC_CPU_2_PCIE_MEM_WIN0_HI + ((win) * 8) |
| |
| #define PCIE_MISC_RC_BAR1_CONFIG_LO 0x402c |
| #define PCIE_MISC_RC_BAR1_CONFIG_LO_SIZE_MASK 0x1f |
| |
| #define PCIE_MISC_RC_BAR2_CONFIG_LO 0x4034 |
| #define PCIE_MISC_RC_BAR2_CONFIG_LO_SIZE_MASK 0x1f |
| #define PCIE_MISC_RC_BAR2_CONFIG_HI 0x4038 |
| |
| #define PCIE_MISC_RC_BAR3_CONFIG_LO 0x403c |
| #define PCIE_MISC_RC_BAR3_CONFIG_LO_SIZE_MASK 0x1f |
| |
| #define PCIE_MISC_MSI_BAR_CONFIG_LO 0x4044 |
| #define PCIE_MISC_MSI_BAR_CONFIG_HI 0x4048 |
| |
| #define PCIE_MISC_MSI_DATA_CONFIG 0x404c |
| #define PCIE_MISC_MSI_DATA_CONFIG_VAL_32 0xffe06540 |
| #define PCIE_MISC_MSI_DATA_CONFIG_VAL_8 0xfff86540 |
| |
| #define PCIE_MISC_PCIE_CTRL 0x4064 |
| #define PCIE_MISC_PCIE_CTRL_PCIE_L23_REQUEST_MASK 0x1 |
| #define PCIE_MISC_PCIE_CTRL_PCIE_PERSTB_MASK 0x4 |
| |
| #define PCIE_MISC_PCIE_STATUS 0x4068 |
| #define PCIE_MISC_PCIE_STATUS_PCIE_PORT_MASK 0x80 |
| #define PCIE_MISC_PCIE_STATUS_PCIE_DL_ACTIVE_MASK 0x20 |
| #define PCIE_MISC_PCIE_STATUS_PCIE_PHYLINKUP_MASK 0x10 |
| #define PCIE_MISC_PCIE_STATUS_PCIE_LINK_IN_L23_MASK 0x40 |
| |
| #define PCIE_MISC_REVISION 0x406c |
| #define BRCM_PCIE_HW_REV_33 0x0303 |
| #define BRCM_PCIE_HW_REV_3_20 0x0320 |
| |
| #define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_LIMIT 0x4070 |
| #define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_LIMIT_LIMIT_MASK 0xfff00000 |
| #define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_LIMIT_BASE_MASK 0xfff0 |
| #define PCIE_MEM_WIN0_BASE_LIMIT(win) \ |
| PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_LIMIT + ((win) * 4) |
| |
| #define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_HI 0x4080 |
| #define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_HI_BASE_MASK 0xff |
| #define PCIE_MEM_WIN0_BASE_HI(win) \ |
| PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_HI + ((win) * 8) |
| |
| #define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_LIMIT_HI 0x4084 |
| #define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_LIMIT_HI_LIMIT_MASK 0xff |
| #define PCIE_MEM_WIN0_LIMIT_HI(win) \ |
| PCIE_MISC_CPU_2_PCIE_MEM_WIN0_LIMIT_HI + ((win) * 8) |
| |
| #define PCIE_MISC_HARD_PCIE_HARD_DEBUG 0x4204 |
| #define PCIE_MISC_HARD_PCIE_HARD_DEBUG_CLKREQ_DEBUG_ENABLE_MASK 0x2 |
| #define PCIE_MISC_HARD_PCIE_HARD_DEBUG_SERDES_IDDQ_MASK 0x08000000 |
| #define PCIE_BMIPS_MISC_HARD_PCIE_HARD_DEBUG_SERDES_IDDQ_MASK 0x00800000 |
| |
| |
| #define PCIE_INTR2_CPU_BASE 0x4300 |
| #define PCIE_MSI_INTR2_BASE 0x4500 |
| /* Offsets from PCIE_INTR2_CPU_BASE and PCIE_MSI_INTR2_BASE */ |
| #define MSI_INT_STATUS 0x0 |
| #define MSI_INT_CLR 0x8 |
| #define MSI_INT_MASK_SET 0x10 |
| #define MSI_INT_MASK_CLR 0x14 |
| |
| #define PCIE_EXT_CFG_DATA 0x8000 |
| #define PCIE_EXT_CFG_INDEX 0x9000 |
| |
| #define PCIE_RGR1_SW_INIT_1_PERST_MASK 0x1 |
| #define PCIE_RGR1_SW_INIT_1_PERST_SHIFT 0x0 |
| |
| #define RGR1_SW_INIT_1_INIT_GENERIC_MASK 0x2 |
| #define RGR1_SW_INIT_1_INIT_GENERIC_SHIFT 0x1 |
| #define RGR1_SW_INIT_1_INIT_7278_MASK 0x1 |
| #define RGR1_SW_INIT_1_INIT_7278_SHIFT 0x0 |
| |
| /* PCIe parameters */ |
| #define BRCM_NUM_PCIE_OUT_WINS 0x4 |
| #define BRCM_INT_PCI_MSI_NR 32 |
| #define BRCM_INT_PCI_MSI_LEGACY_NR 8 |
| #define BRCM_INT_PCI_MSI_SHIFT 0 |
| #define BRCM_INT_PCI_MSI_MASK GENMASK(BRCM_INT_PCI_MSI_NR - 1, 0) |
| #define BRCM_INT_PCI_MSI_LEGACY_MASK GENMASK(31, \ |
| 32 - BRCM_INT_PCI_MSI_LEGACY_NR) |
| |
| /* MSI target addresses */ |
| #define BRCM_MSI_TARGET_ADDR_LT_4GB 0x0fffffffcULL |
| #define BRCM_MSI_TARGET_ADDR_GT_4GB 0xffffffffcULL |
| |
| /* MDIO registers */ |
| #define MDIO_PORT0 0x0 |
| #define MDIO_DATA_MASK 0x7fffffff |
| #define MDIO_PORT_MASK 0xf0000 |
| #define MDIO_REGAD_MASK 0xffff |
| #define MDIO_CMD_MASK 0xfff00000 |
| #define MDIO_CMD_READ 0x1 |
| #define MDIO_CMD_WRITE 0x0 |
| #define MDIO_DATA_DONE_MASK 0x80000000 |
| #define MDIO_RD_DONE(x) (((x) & MDIO_DATA_DONE_MASK) ? 1 : 0) |
| #define MDIO_WT_DONE(x) (((x) & MDIO_DATA_DONE_MASK) ? 0 : 1) |
| #define SSC_REGS_ADDR 0x1100 |
| #define SET_ADDR_OFFSET 0x1f |
| #define SSC_CNTL_OFFSET 0x2 |
| #define SSC_CNTL_OVRD_EN_MASK 0x8000 |
| #define SSC_CNTL_OVRD_VAL_MASK 0x4000 |
| #define SSC_STATUS_OFFSET 0x1 |
| #define SSC_STATUS_SSC_MASK 0x400 |
| #define SSC_STATUS_PLL_LOCK_MASK 0x800 |
| #define PCIE_BRCM_MAX_MEMC 3 |
| |
| #define IDX_ADDR(pcie) (pcie->reg_offsets[EXT_CFG_INDEX]) |
| #define DATA_ADDR(pcie) (pcie->reg_offsets[EXT_CFG_DATA]) |
| #define PCIE_RGR1_SW_INIT_1(pcie) (pcie->reg_offsets[RGR1_SW_INIT_1]) |
| |
| /* Rescal registers */ |
| #define PCIE_DVT_PMU_PCIE_PHY_CTRL 0xc700 |
| #define PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_NFLDS 0x3 |
| #define PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_DIG_RESET_MASK 0x4 |
| #define PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_DIG_RESET_SHIFT 0x2 |
| #define PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_RESET_MASK 0x2 |
| #define PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_RESET_SHIFT 0x1 |
| #define PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_PWRDN_MASK 0x1 |
| #define PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_PWRDN_SHIFT 0x0 |
| |
| /* Forward declarations */ |
| struct brcm_pcie; |
| |
| enum { |
| RGR1_SW_INIT_1, |
| EXT_CFG_INDEX, |
| EXT_CFG_DATA, |
| }; |
| |
| enum { |
| RGR1_SW_INIT_1_INIT_MASK, |
| RGR1_SW_INIT_1_INIT_SHIFT, |
| }; |
| |
| enum pcie_type { |
| GENERIC, |
| BCM7425, |
| BCM7435, |
| BCM4908, |
| BCM7278, |
| BCM2711, |
| }; |
| |
| struct pcie_cfg_data { |
| const int *offsets; |
| const enum pcie_type type; |
| void (*perst_set)(struct brcm_pcie *pcie, u32 val); |
| void (*bridge_sw_init_set)(struct brcm_pcie *pcie, u32 val); |
| }; |
| |
| struct subdev_regulators { |
| unsigned int num_supplies; |
| struct regulator_bulk_data supplies[]; |
| }; |
| |
| struct brcm_msi { |
| struct device *dev; |
| void __iomem *base; |
| struct device_node *np; |
| struct irq_domain *msi_domain; |
| struct irq_domain *inner_domain; |
| struct mutex lock; /* guards the alloc/free operations */ |
| u64 target_addr; |
| int irq; |
| DECLARE_BITMAP(used, BRCM_INT_PCI_MSI_NR); |
| bool legacy; |
| /* Some chips have MSIs in bits [31..24] of a shared register. */ |
| int legacy_shift; |
| int nr; /* No. of MSI available, depends on chip */ |
| /* This is the base pointer for interrupt status/set/clr regs */ |
| void __iomem *intr_base; |
| }; |
| |
| /* Internal PCIe Host Controller Information.*/ |
| struct brcm_pcie { |
| struct device *dev; |
| void __iomem *base; |
| struct clk *clk; |
| struct device_node *np; |
| bool ssc; |
| int gen; |
| u64 msi_target_addr; |
| struct brcm_msi *msi; |
| const int *reg_offsets; |
| enum pcie_type type; |
| struct reset_control *rescal; |
| struct reset_control *perst_reset; |
| int num_memc; |
| u64 memc_size[PCIE_BRCM_MAX_MEMC]; |
| u32 hw_rev; |
| void (*perst_set)(struct brcm_pcie *pcie, u32 val); |
| void (*bridge_sw_init_set)(struct brcm_pcie *pcie, u32 val); |
| struct subdev_regulators *sr; |
| bool ep_wakeup_capable; |
| }; |
| |
| static inline bool is_bmips(const struct brcm_pcie *pcie) |
| { |
| return pcie->type == BCM7435 || pcie->type == BCM7425; |
| } |
| |
| /* |
| * This is to convert the size of the inbound "BAR" region to the |
| * non-linear values of PCIE_X_MISC_RC_BAR[123]_CONFIG_LO.SIZE |
| */ |
| static int brcm_pcie_encode_ibar_size(u64 size) |
| { |
| int log2_in = ilog2(size); |
| |
| if (log2_in >= 12 && log2_in <= 15) |
| /* Covers 4KB to 32KB (inclusive) */ |
| return (log2_in - 12) + 0x1c; |
| else if (log2_in >= 16 && log2_in <= 35) |
| /* Covers 64KB to 32GB, (inclusive) */ |
| return log2_in - 15; |
| /* Something is awry so disable */ |
| return 0; |
| } |
| |
| static u32 brcm_pcie_mdio_form_pkt(int port, int regad, int cmd) |
| { |
| u32 pkt = 0; |
| |
| pkt |= FIELD_PREP(MDIO_PORT_MASK, port); |
| pkt |= FIELD_PREP(MDIO_REGAD_MASK, regad); |
| pkt |= FIELD_PREP(MDIO_CMD_MASK, cmd); |
| |
| return pkt; |
| } |
| |
| /* negative return value indicates error */ |
| static int brcm_pcie_mdio_read(void __iomem *base, u8 port, u8 regad, u32 *val) |
| { |
| u32 data; |
| int err; |
| |
| writel(brcm_pcie_mdio_form_pkt(port, regad, MDIO_CMD_READ), |
| base + PCIE_RC_DL_MDIO_ADDR); |
| readl(base + PCIE_RC_DL_MDIO_ADDR); |
| err = readl_poll_timeout_atomic(base + PCIE_RC_DL_MDIO_RD_DATA, data, |
| MDIO_RD_DONE(data), 10, 100); |
| *val = FIELD_GET(MDIO_DATA_MASK, data); |
| |
| return err; |
| } |
| |
| /* negative return value indicates error */ |
| static int brcm_pcie_mdio_write(void __iomem *base, u8 port, |
| u8 regad, u16 wrdata) |
| { |
| u32 data; |
| int err; |
| |
| writel(brcm_pcie_mdio_form_pkt(port, regad, MDIO_CMD_WRITE), |
| base + PCIE_RC_DL_MDIO_ADDR); |
| readl(base + PCIE_RC_DL_MDIO_ADDR); |
| writel(MDIO_DATA_DONE_MASK | wrdata, base + PCIE_RC_DL_MDIO_WR_DATA); |
| |
| err = readw_poll_timeout_atomic(base + PCIE_RC_DL_MDIO_WR_DATA, data, |
| MDIO_WT_DONE(data), 10, 100); |
| return err; |
| } |
| |
| /* |
| * Configures device for Spread Spectrum Clocking (SSC) mode; a negative |
| * return value indicates error. |
| */ |
| static int brcm_pcie_set_ssc(struct brcm_pcie *pcie) |
| { |
| int pll, ssc; |
| int ret; |
| u32 tmp; |
| |
| ret = brcm_pcie_mdio_write(pcie->base, MDIO_PORT0, SET_ADDR_OFFSET, |
| SSC_REGS_ADDR); |
| if (ret < 0) |
| return ret; |
| |
| ret = brcm_pcie_mdio_read(pcie->base, MDIO_PORT0, |
| SSC_CNTL_OFFSET, &tmp); |
| if (ret < 0) |
| return ret; |
| |
| u32p_replace_bits(&tmp, 1, SSC_CNTL_OVRD_EN_MASK); |
| u32p_replace_bits(&tmp, 1, SSC_CNTL_OVRD_VAL_MASK); |
| ret = brcm_pcie_mdio_write(pcie->base, MDIO_PORT0, |
| SSC_CNTL_OFFSET, tmp); |
| if (ret < 0) |
| return ret; |
| |
| usleep_range(1000, 2000); |
| ret = brcm_pcie_mdio_read(pcie->base, MDIO_PORT0, |
| SSC_STATUS_OFFSET, &tmp); |
| if (ret < 0) |
| return ret; |
| |
| ssc = FIELD_GET(SSC_STATUS_SSC_MASK, tmp); |
| pll = FIELD_GET(SSC_STATUS_PLL_LOCK_MASK, tmp); |
| |
| return ssc && pll ? 0 : -EIO; |
| } |
| |
| /* Limits operation to a specific generation (1, 2, or 3) */ |
| static void brcm_pcie_set_gen(struct brcm_pcie *pcie, int gen) |
| { |
| u16 lnkctl2 = readw(pcie->base + BRCM_PCIE_CAP_REGS + PCI_EXP_LNKCTL2); |
| u32 lnkcap = readl(pcie->base + BRCM_PCIE_CAP_REGS + PCI_EXP_LNKCAP); |
| |
| lnkcap = (lnkcap & ~PCI_EXP_LNKCAP_SLS) | gen; |
| writel(lnkcap, pcie->base + BRCM_PCIE_CAP_REGS + PCI_EXP_LNKCAP); |
| |
| lnkctl2 = (lnkctl2 & ~0xf) | gen; |
| writew(lnkctl2, pcie->base + BRCM_PCIE_CAP_REGS + PCI_EXP_LNKCTL2); |
| } |
| |
| static void brcm_pcie_set_outbound_win(struct brcm_pcie *pcie, |
| unsigned int win, u64 cpu_addr, |
| u64 pcie_addr, u64 size) |
| { |
| u32 cpu_addr_mb_high, limit_addr_mb_high; |
| phys_addr_t cpu_addr_mb, limit_addr_mb; |
| int high_addr_shift; |
| u32 tmp; |
| |
| /* Set the base of the pcie_addr window */ |
| writel(lower_32_bits(pcie_addr), pcie->base + PCIE_MEM_WIN0_LO(win)); |
| writel(upper_32_bits(pcie_addr), pcie->base + PCIE_MEM_WIN0_HI(win)); |
| |
| /* Write the addr base & limit lower bits (in MBs) */ |
| cpu_addr_mb = cpu_addr / SZ_1M; |
| limit_addr_mb = (cpu_addr + size - 1) / SZ_1M; |
| |
| tmp = readl(pcie->base + PCIE_MEM_WIN0_BASE_LIMIT(win)); |
| u32p_replace_bits(&tmp, cpu_addr_mb, |
| PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_LIMIT_BASE_MASK); |
| u32p_replace_bits(&tmp, limit_addr_mb, |
| PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_LIMIT_LIMIT_MASK); |
| writel(tmp, pcie->base + PCIE_MEM_WIN0_BASE_LIMIT(win)); |
| |
| if (is_bmips(pcie)) |
| return; |
| |
| /* Write the cpu & limit addr upper bits */ |
| high_addr_shift = |
| HWEIGHT32(PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_LIMIT_BASE_MASK); |
| |
| cpu_addr_mb_high = cpu_addr_mb >> high_addr_shift; |
| tmp = readl(pcie->base + PCIE_MEM_WIN0_BASE_HI(win)); |
| u32p_replace_bits(&tmp, cpu_addr_mb_high, |
| PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_HI_BASE_MASK); |
| writel(tmp, pcie->base + PCIE_MEM_WIN0_BASE_HI(win)); |
| |
| limit_addr_mb_high = limit_addr_mb >> high_addr_shift; |
| tmp = readl(pcie->base + PCIE_MEM_WIN0_LIMIT_HI(win)); |
| u32p_replace_bits(&tmp, limit_addr_mb_high, |
| PCIE_MISC_CPU_2_PCIE_MEM_WIN0_LIMIT_HI_LIMIT_MASK); |
| writel(tmp, pcie->base + PCIE_MEM_WIN0_LIMIT_HI(win)); |
| } |
| |
| static struct irq_chip brcm_msi_irq_chip = { |
| .name = "BRCM STB PCIe MSI", |
| .irq_ack = irq_chip_ack_parent, |
| .irq_mask = pci_msi_mask_irq, |
| .irq_unmask = pci_msi_unmask_irq, |
| }; |
| |
| static struct msi_domain_info brcm_msi_domain_info = { |
| .flags = (MSI_FLAG_USE_DEF_DOM_OPS | MSI_FLAG_USE_DEF_CHIP_OPS | |
| MSI_FLAG_MULTI_PCI_MSI), |
| .chip = &brcm_msi_irq_chip, |
| }; |
| |
| static void brcm_pcie_msi_isr(struct irq_desc *desc) |
| { |
| struct irq_chip *chip = irq_desc_get_chip(desc); |
| unsigned long status; |
| struct brcm_msi *msi; |
| struct device *dev; |
| u32 bit; |
| |
| chained_irq_enter(chip, desc); |
| msi = irq_desc_get_handler_data(desc); |
| dev = msi->dev; |
| |
| status = readl(msi->intr_base + MSI_INT_STATUS); |
| status >>= msi->legacy_shift; |
| |
| for_each_set_bit(bit, &status, msi->nr) { |
| int ret; |
| ret = generic_handle_domain_irq(msi->inner_domain, bit); |
| if (ret) |
| dev_dbg(dev, "unexpected MSI\n"); |
| } |
| |
| chained_irq_exit(chip, desc); |
| } |
| |
| static void brcm_msi_compose_msi_msg(struct irq_data *data, struct msi_msg *msg) |
| { |
| struct brcm_msi *msi = irq_data_get_irq_chip_data(data); |
| |
| msg->address_lo = lower_32_bits(msi->target_addr); |
| msg->address_hi = upper_32_bits(msi->target_addr); |
| msg->data = (0xffff & PCIE_MISC_MSI_DATA_CONFIG_VAL_32) | data->hwirq; |
| } |
| |
| static int brcm_msi_set_affinity(struct irq_data *irq_data, |
| const struct cpumask *mask, bool force) |
| { |
| return -EINVAL; |
| } |
| |
| static void brcm_msi_ack_irq(struct irq_data *data) |
| { |
| struct brcm_msi *msi = irq_data_get_irq_chip_data(data); |
| const int shift_amt = data->hwirq + msi->legacy_shift; |
| |
| writel(1 << shift_amt, msi->intr_base + MSI_INT_CLR); |
| } |
| |
| |
| static struct irq_chip brcm_msi_bottom_irq_chip = { |
| .name = "BRCM STB MSI", |
| .irq_compose_msi_msg = brcm_msi_compose_msi_msg, |
| .irq_set_affinity = brcm_msi_set_affinity, |
| .irq_ack = brcm_msi_ack_irq, |
| }; |
| |
| static int brcm_msi_alloc(struct brcm_msi *msi, unsigned int nr_irqs) |
| { |
| int hwirq; |
| |
| mutex_lock(&msi->lock); |
| hwirq = bitmap_find_free_region(msi->used, msi->nr, |
| order_base_2(nr_irqs)); |
| mutex_unlock(&msi->lock); |
| |
| return hwirq; |
| } |
| |
| static void brcm_msi_free(struct brcm_msi *msi, unsigned long hwirq, |
| unsigned int nr_irqs) |
| { |
| mutex_lock(&msi->lock); |
| bitmap_release_region(msi->used, hwirq, order_base_2(nr_irqs)); |
| mutex_unlock(&msi->lock); |
| } |
| |
| static int brcm_irq_domain_alloc(struct irq_domain *domain, unsigned int virq, |
| unsigned int nr_irqs, void *args) |
| { |
| struct brcm_msi *msi = domain->host_data; |
| int hwirq, i; |
| |
| hwirq = brcm_msi_alloc(msi, nr_irqs); |
| |
| if (hwirq < 0) |
| return hwirq; |
| |
| for (i = 0; i < nr_irqs; i++) |
| irq_domain_set_info(domain, virq + i, hwirq + i, |
| &brcm_msi_bottom_irq_chip, domain->host_data, |
| handle_edge_irq, NULL, NULL); |
| return 0; |
| } |
| |
| static void brcm_irq_domain_free(struct irq_domain *domain, |
| unsigned int virq, unsigned int nr_irqs) |
| { |
| struct irq_data *d = irq_domain_get_irq_data(domain, virq); |
| struct brcm_msi *msi = irq_data_get_irq_chip_data(d); |
| |
| brcm_msi_free(msi, d->hwirq, nr_irqs); |
| } |
| |
| static const struct irq_domain_ops msi_domain_ops = { |
| .alloc = brcm_irq_domain_alloc, |
| .free = brcm_irq_domain_free, |
| }; |
| |
| static int brcm_allocate_domains(struct brcm_msi *msi) |
| { |
| struct fwnode_handle *fwnode = of_node_to_fwnode(msi->np); |
| struct device *dev = msi->dev; |
| |
| msi->inner_domain = irq_domain_add_linear(NULL, msi->nr, &msi_domain_ops, msi); |
| if (!msi->inner_domain) { |
| dev_err(dev, "failed to create IRQ domain\n"); |
| return -ENOMEM; |
| } |
| |
| msi->msi_domain = pci_msi_create_irq_domain(fwnode, |
| &brcm_msi_domain_info, |
| msi->inner_domain); |
| if (!msi->msi_domain) { |
| dev_err(dev, "failed to create MSI domain\n"); |
| irq_domain_remove(msi->inner_domain); |
| return -ENOMEM; |
| } |
| |
| return 0; |
| } |
| |
| static void brcm_free_domains(struct brcm_msi *msi) |
| { |
| irq_domain_remove(msi->msi_domain); |
| irq_domain_remove(msi->inner_domain); |
| } |
| |
| static void brcm_msi_remove(struct brcm_pcie *pcie) |
| { |
| struct brcm_msi *msi = pcie->msi; |
| |
| if (!msi) |
| return; |
| irq_set_chained_handler_and_data(msi->irq, NULL, NULL); |
| brcm_free_domains(msi); |
| } |
| |
| static void brcm_msi_set_regs(struct brcm_msi *msi) |
| { |
| u32 val = msi->legacy ? BRCM_INT_PCI_MSI_LEGACY_MASK : |
| BRCM_INT_PCI_MSI_MASK; |
| |
| writel(val, msi->intr_base + MSI_INT_MASK_CLR); |
| writel(val, msi->intr_base + MSI_INT_CLR); |
| |
| /* |
| * The 0 bit of PCIE_MISC_MSI_BAR_CONFIG_LO is repurposed to MSI |
| * enable, which we set to 1. |
| */ |
| writel(lower_32_bits(msi->target_addr) | 0x1, |
| msi->base + PCIE_MISC_MSI_BAR_CONFIG_LO); |
| writel(upper_32_bits(msi->target_addr), |
| msi->base + PCIE_MISC_MSI_BAR_CONFIG_HI); |
| |
| val = msi->legacy ? PCIE_MISC_MSI_DATA_CONFIG_VAL_8 : PCIE_MISC_MSI_DATA_CONFIG_VAL_32; |
| writel(val, msi->base + PCIE_MISC_MSI_DATA_CONFIG); |
| } |
| |
| static int brcm_pcie_enable_msi(struct brcm_pcie *pcie) |
| { |
| struct brcm_msi *msi; |
| int irq, ret; |
| struct device *dev = pcie->dev; |
| |
| irq = irq_of_parse_and_map(dev->of_node, 1); |
| if (irq <= 0) { |
| dev_err(dev, "cannot map MSI interrupt\n"); |
| return -ENODEV; |
| } |
| |
| msi = devm_kzalloc(dev, sizeof(struct brcm_msi), GFP_KERNEL); |
| if (!msi) |
| return -ENOMEM; |
| |
| mutex_init(&msi->lock); |
| msi->dev = dev; |
| msi->base = pcie->base; |
| msi->np = pcie->np; |
| msi->target_addr = pcie->msi_target_addr; |
| msi->irq = irq; |
| msi->legacy = pcie->hw_rev < BRCM_PCIE_HW_REV_33; |
| |
| /* |
| * Sanity check to make sure that the 'used' bitmap in struct brcm_msi |
| * is large enough. |
| */ |
| BUILD_BUG_ON(BRCM_INT_PCI_MSI_LEGACY_NR > BRCM_INT_PCI_MSI_NR); |
| |
| if (msi->legacy) { |
| msi->intr_base = msi->base + PCIE_INTR2_CPU_BASE; |
| msi->nr = BRCM_INT_PCI_MSI_LEGACY_NR; |
| msi->legacy_shift = 24; |
| } else { |
| msi->intr_base = msi->base + PCIE_MSI_INTR2_BASE; |
| msi->nr = BRCM_INT_PCI_MSI_NR; |
| msi->legacy_shift = 0; |
| } |
| |
| ret = brcm_allocate_domains(msi); |
| if (ret) |
| return ret; |
| |
| irq_set_chained_handler_and_data(msi->irq, brcm_pcie_msi_isr, msi); |
| |
| brcm_msi_set_regs(msi); |
| pcie->msi = msi; |
| |
| return 0; |
| } |
| |
| /* The controller is capable of serving in both RC and EP roles */ |
| static bool brcm_pcie_rc_mode(struct brcm_pcie *pcie) |
| { |
| void __iomem *base = pcie->base; |
| u32 val = readl(base + PCIE_MISC_PCIE_STATUS); |
| |
| return !!FIELD_GET(PCIE_MISC_PCIE_STATUS_PCIE_PORT_MASK, val); |
| } |
| |
| static bool brcm_pcie_link_up(struct brcm_pcie *pcie) |
| { |
| u32 val = readl(pcie->base + PCIE_MISC_PCIE_STATUS); |
| u32 dla = FIELD_GET(PCIE_MISC_PCIE_STATUS_PCIE_DL_ACTIVE_MASK, val); |
| u32 plu = FIELD_GET(PCIE_MISC_PCIE_STATUS_PCIE_PHYLINKUP_MASK, val); |
| |
| return dla && plu; |
| } |
| |
| static void __iomem *brcm_pcie_map_bus(struct pci_bus *bus, |
| unsigned int devfn, int where) |
| { |
| struct brcm_pcie *pcie = bus->sysdata; |
| void __iomem *base = pcie->base; |
| int idx; |
| |
| /* Accesses to the RC go right to the RC registers if !devfn */ |
| if (pci_is_root_bus(bus)) |
| return devfn ? NULL : base + PCIE_ECAM_REG(where); |
| |
| /* An access to our HW w/o link-up will cause a CPU Abort */ |
| if (!brcm_pcie_link_up(pcie)) |
| return NULL; |
| |
| /* For devices, write to the config space index register */ |
| idx = PCIE_ECAM_OFFSET(bus->number, devfn, 0); |
| writel(idx, pcie->base + PCIE_EXT_CFG_INDEX); |
| return base + PCIE_EXT_CFG_DATA + PCIE_ECAM_REG(where); |
| } |
| |
| static void __iomem *brcm7425_pcie_map_bus(struct pci_bus *bus, |
| unsigned int devfn, int where) |
| { |
| struct brcm_pcie *pcie = bus->sysdata; |
| void __iomem *base = pcie->base; |
| int idx; |
| |
| /* Accesses to the RC go right to the RC registers if !devfn */ |
| if (pci_is_root_bus(bus)) |
| return devfn ? NULL : base + PCIE_ECAM_REG(where); |
| |
| /* An access to our HW w/o link-up will cause a CPU Abort */ |
| if (!brcm_pcie_link_up(pcie)) |
| return NULL; |
| |
| /* For devices, write to the config space index register */ |
| idx = PCIE_ECAM_OFFSET(bus->number, devfn, where); |
| writel(idx, base + IDX_ADDR(pcie)); |
| return base + DATA_ADDR(pcie); |
| } |
| |
| static void brcm_pcie_bridge_sw_init_set_generic(struct brcm_pcie *pcie, u32 val) |
| { |
| u32 tmp, mask = RGR1_SW_INIT_1_INIT_GENERIC_MASK; |
| u32 shift = RGR1_SW_INIT_1_INIT_GENERIC_SHIFT; |
| |
| tmp = readl(pcie->base + PCIE_RGR1_SW_INIT_1(pcie)); |
| tmp = (tmp & ~mask) | ((val << shift) & mask); |
| writel(tmp, pcie->base + PCIE_RGR1_SW_INIT_1(pcie)); |
| } |
| |
| static void brcm_pcie_bridge_sw_init_set_7278(struct brcm_pcie *pcie, u32 val) |
| { |
| u32 tmp, mask = RGR1_SW_INIT_1_INIT_7278_MASK; |
| u32 shift = RGR1_SW_INIT_1_INIT_7278_SHIFT; |
| |
| tmp = readl(pcie->base + PCIE_RGR1_SW_INIT_1(pcie)); |
| tmp = (tmp & ~mask) | ((val << shift) & mask); |
| writel(tmp, pcie->base + PCIE_RGR1_SW_INIT_1(pcie)); |
| } |
| |
| static void brcm_pcie_perst_set_4908(struct brcm_pcie *pcie, u32 val) |
| { |
| if (WARN_ONCE(!pcie->perst_reset, "missing PERST# reset controller\n")) |
| return; |
| |
| if (val) |
| reset_control_assert(pcie->perst_reset); |
| else |
| reset_control_deassert(pcie->perst_reset); |
| } |
| |
| static void brcm_pcie_perst_set_7278(struct brcm_pcie *pcie, u32 val) |
| { |
| u32 tmp; |
| |
| /* Perst bit has moved and assert value is 0 */ |
| tmp = readl(pcie->base + PCIE_MISC_PCIE_CTRL); |
| u32p_replace_bits(&tmp, !val, PCIE_MISC_PCIE_CTRL_PCIE_PERSTB_MASK); |
| writel(tmp, pcie->base + PCIE_MISC_PCIE_CTRL); |
| } |
| |
| static void brcm_pcie_perst_set_generic(struct brcm_pcie *pcie, u32 val) |
| { |
| u32 tmp; |
| |
| tmp = readl(pcie->base + PCIE_RGR1_SW_INIT_1(pcie)); |
| u32p_replace_bits(&tmp, val, PCIE_RGR1_SW_INIT_1_PERST_MASK); |
| writel(tmp, pcie->base + PCIE_RGR1_SW_INIT_1(pcie)); |
| } |
| |
| static int brcm_pcie_get_rc_bar2_size_and_offset(struct brcm_pcie *pcie, |
| u64 *rc_bar2_size, |
| u64 *rc_bar2_offset) |
| { |
| struct pci_host_bridge *bridge = pci_host_bridge_from_priv(pcie); |
| struct resource_entry *entry; |
| struct device *dev = pcie->dev; |
| u64 lowest_pcie_addr = ~(u64)0; |
| int ret, i = 0; |
| u64 size = 0; |
| |
| resource_list_for_each_entry(entry, &bridge->dma_ranges) { |
| u64 pcie_beg = entry->res->start - entry->offset; |
| |
| size += entry->res->end - entry->res->start + 1; |
| if (pcie_beg < lowest_pcie_addr) |
| lowest_pcie_addr = pcie_beg; |
| } |
| |
| if (lowest_pcie_addr == ~(u64)0) { |
| dev_err(dev, "DT node has no dma-ranges\n"); |
| return -EINVAL; |
| } |
| |
| ret = of_property_read_variable_u64_array(pcie->np, "brcm,scb-sizes", pcie->memc_size, 1, |
| PCIE_BRCM_MAX_MEMC); |
| |
| if (ret <= 0) { |
| /* Make an educated guess */ |
| pcie->num_memc = 1; |
| pcie->memc_size[0] = 1ULL << fls64(size - 1); |
| } else { |
| pcie->num_memc = ret; |
| } |
| |
| /* Each memc is viewed through a "port" that is a power of 2 */ |
| for (i = 0, size = 0; i < pcie->num_memc; i++) |
| size += pcie->memc_size[i]; |
| |
| /* System memory starts at this address in PCIe-space */ |
| *rc_bar2_offset = lowest_pcie_addr; |
| /* The sum of all memc views must also be a power of 2 */ |
| *rc_bar2_size = 1ULL << fls64(size - 1); |
| |
| /* |
| * We validate the inbound memory view even though we should trust |
| * whatever the device-tree provides. This is because of an HW issue on |
| * early Raspberry Pi 4's revisions (bcm2711). It turns out its |
| * firmware has to dynamically edit dma-ranges due to a bug on the |
| * PCIe controller integration, which prohibits any access above the |
| * lower 3GB of memory. Given this, we decided to keep the dma-ranges |
| * in check, avoiding hard to debug device-tree related issues in the |
| * future: |
| * |
| * The PCIe host controller by design must set the inbound viewport to |
| * be a contiguous arrangement of all of the system's memory. In |
| * addition, its size mut be a power of two. To further complicate |
| * matters, the viewport must start on a pcie-address that is aligned |
| * on a multiple of its size. If a portion of the viewport does not |
| * represent system memory -- e.g. 3GB of memory requires a 4GB |
| * viewport -- we can map the outbound memory in or after 3GB and even |
| * though the viewport will overlap the outbound memory the controller |
| * will know to send outbound memory downstream and everything else |
| * upstream. |
| * |
| * For example: |
| * |
| * - The best-case scenario, memory up to 3GB, is to place the inbound |
| * region in the first 4GB of pcie-space, as some legacy devices can |
| * only address 32bits. We would also like to put the MSI under 4GB |
| * as well, since some devices require a 32bit MSI target address. |
| * |
| * - If the system memory is 4GB or larger we cannot start the inbound |
| * region at location 0 (since we have to allow some space for |
| * outbound memory @ 3GB). So instead it will start at the 1x |
| * multiple of its size |
| */ |
| if (!*rc_bar2_size || (*rc_bar2_offset & (*rc_bar2_size - 1)) || |
| (*rc_bar2_offset < SZ_4G && *rc_bar2_offset > SZ_2G)) { |
| dev_err(dev, "Invalid rc_bar2_offset/size: size 0x%llx, off 0x%llx\n", |
| *rc_bar2_size, *rc_bar2_offset); |
| return -EINVAL; |
| } |
| |
| return 0; |
| } |
| |
| static int brcm_pcie_setup(struct brcm_pcie *pcie) |
| { |
| u64 rc_bar2_offset, rc_bar2_size; |
| void __iomem *base = pcie->base; |
| struct pci_host_bridge *bridge; |
| struct resource_entry *entry; |
| u32 tmp, burst, aspm_support; |
| int num_out_wins = 0; |
| int ret, memc; |
| |
| /* Reset the bridge */ |
| pcie->bridge_sw_init_set(pcie, 1); |
| |
| /* Ensure that PERST# is asserted; some bootloaders may deassert it. */ |
| if (pcie->type == BCM2711) |
| pcie->perst_set(pcie, 1); |
| |
| usleep_range(100, 200); |
| |
| /* Take the bridge out of reset */ |
| pcie->bridge_sw_init_set(pcie, 0); |
| |
| tmp = readl(base + PCIE_MISC_HARD_PCIE_HARD_DEBUG); |
| if (is_bmips(pcie)) |
| tmp &= ~PCIE_BMIPS_MISC_HARD_PCIE_HARD_DEBUG_SERDES_IDDQ_MASK; |
| else |
| tmp &= ~PCIE_MISC_HARD_PCIE_HARD_DEBUG_SERDES_IDDQ_MASK; |
| writel(tmp, base + PCIE_MISC_HARD_PCIE_HARD_DEBUG); |
| /* Wait for SerDes to be stable */ |
| usleep_range(100, 200); |
| |
| /* |
| * SCB_MAX_BURST_SIZE is a two bit field. For GENERIC chips it |
| * is encoded as 0=128, 1=256, 2=512, 3=Rsvd, for BCM7278 it |
| * is encoded as 0=Rsvd, 1=128, 2=256, 3=512. |
| */ |
| if (is_bmips(pcie)) |
| burst = 0x1; /* 256 bytes */ |
| else if (pcie->type == BCM2711) |
| burst = 0x0; /* 128 bytes */ |
| else if (pcie->type == BCM7278) |
| burst = 0x3; /* 512 bytes */ |
| else |
| burst = 0x2; /* 512 bytes */ |
| |
| /* |
| * Set SCB_MAX_BURST_SIZE, CFG_READ_UR_MODE, SCB_ACCESS_EN, |
| * RCB_MPS_MODE, RCB_64B_MODE |
| */ |
| tmp = readl(base + PCIE_MISC_MISC_CTRL); |
| u32p_replace_bits(&tmp, 1, PCIE_MISC_MISC_CTRL_SCB_ACCESS_EN_MASK); |
| u32p_replace_bits(&tmp, 1, PCIE_MISC_MISC_CTRL_CFG_READ_UR_MODE_MASK); |
| u32p_replace_bits(&tmp, burst, PCIE_MISC_MISC_CTRL_MAX_BURST_SIZE_MASK); |
| u32p_replace_bits(&tmp, 1, PCIE_MISC_MISC_CTRL_PCIE_RCB_MPS_MODE_MASK); |
| u32p_replace_bits(&tmp, 1, PCIE_MISC_MISC_CTRL_PCIE_RCB_64B_MODE_MASK); |
| writel(tmp, base + PCIE_MISC_MISC_CTRL); |
| |
| ret = brcm_pcie_get_rc_bar2_size_and_offset(pcie, &rc_bar2_size, |
| &rc_bar2_offset); |
| if (ret) |
| return ret; |
| |
| tmp = lower_32_bits(rc_bar2_offset); |
| u32p_replace_bits(&tmp, brcm_pcie_encode_ibar_size(rc_bar2_size), |
| PCIE_MISC_RC_BAR2_CONFIG_LO_SIZE_MASK); |
| writel(tmp, base + PCIE_MISC_RC_BAR2_CONFIG_LO); |
| writel(upper_32_bits(rc_bar2_offset), |
| base + PCIE_MISC_RC_BAR2_CONFIG_HI); |
| |
| tmp = readl(base + PCIE_MISC_MISC_CTRL); |
| for (memc = 0; memc < pcie->num_memc; memc++) { |
| u32 scb_size_val = ilog2(pcie->memc_size[memc]) - 15; |
| |
| if (memc == 0) |
| u32p_replace_bits(&tmp, scb_size_val, SCB_SIZE_MASK(0)); |
| else if (memc == 1) |
| u32p_replace_bits(&tmp, scb_size_val, SCB_SIZE_MASK(1)); |
| else if (memc == 2) |
| u32p_replace_bits(&tmp, scb_size_val, SCB_SIZE_MASK(2)); |
| } |
| writel(tmp, base + PCIE_MISC_MISC_CTRL); |
| |
| /* |
| * We ideally want the MSI target address to be located in the 32bit |
| * addressable memory area. Some devices might depend on it. This is |
| * possible either when the inbound window is located above the lower |
| * 4GB or when the inbound area is smaller than 4GB (taking into |
| * account the rounding-up we're forced to perform). |
| */ |
| if (rc_bar2_offset >= SZ_4G || (rc_bar2_size + rc_bar2_offset) < SZ_4G) |
| pcie->msi_target_addr = BRCM_MSI_TARGET_ADDR_LT_4GB; |
| else |
| pcie->msi_target_addr = BRCM_MSI_TARGET_ADDR_GT_4GB; |
| |
| if (!brcm_pcie_rc_mode(pcie)) { |
| dev_err(pcie->dev, "PCIe RC controller misconfigured as Endpoint\n"); |
| return -EINVAL; |
| } |
| |
| /* disable the PCIe->GISB memory window (RC_BAR1) */ |
| tmp = readl(base + PCIE_MISC_RC_BAR1_CONFIG_LO); |
| tmp &= ~PCIE_MISC_RC_BAR1_CONFIG_LO_SIZE_MASK; |
| writel(tmp, base + PCIE_MISC_RC_BAR1_CONFIG_LO); |
| |
| /* disable the PCIe->SCB memory window (RC_BAR3) */ |
| tmp = readl(base + PCIE_MISC_RC_BAR3_CONFIG_LO); |
| tmp &= ~PCIE_MISC_RC_BAR3_CONFIG_LO_SIZE_MASK; |
| writel(tmp, base + PCIE_MISC_RC_BAR3_CONFIG_LO); |
| |
| /* Don't advertise L0s capability if 'aspm-no-l0s' */ |
| aspm_support = PCIE_LINK_STATE_L1; |
| if (!of_property_read_bool(pcie->np, "aspm-no-l0s")) |
| aspm_support |= PCIE_LINK_STATE_L0S; |
| tmp = readl(base + PCIE_RC_CFG_PRIV1_LINK_CAPABILITY); |
| u32p_replace_bits(&tmp, aspm_support, |
| PCIE_RC_CFG_PRIV1_LINK_CAPABILITY_ASPM_SUPPORT_MASK); |
| writel(tmp, base + PCIE_RC_CFG_PRIV1_LINK_CAPABILITY); |
| |
| /* |
| * For config space accesses on the RC, show the right class for |
| * a PCIe-PCIe bridge (the default setting is to be EP mode). |
| */ |
| tmp = readl(base + PCIE_RC_CFG_PRIV1_ID_VAL3); |
| u32p_replace_bits(&tmp, 0x060400, |
| PCIE_RC_CFG_PRIV1_ID_VAL3_CLASS_CODE_MASK); |
| writel(tmp, base + PCIE_RC_CFG_PRIV1_ID_VAL3); |
| |
| bridge = pci_host_bridge_from_priv(pcie); |
| resource_list_for_each_entry(entry, &bridge->windows) { |
| struct resource *res = entry->res; |
| |
| if (resource_type(res) != IORESOURCE_MEM) |
| continue; |
| |
| if (num_out_wins >= BRCM_NUM_PCIE_OUT_WINS) { |
| dev_err(pcie->dev, "too many outbound wins\n"); |
| return -EINVAL; |
| } |
| |
| if (is_bmips(pcie)) { |
| u64 start = res->start; |
| unsigned int j, nwins = resource_size(res) / SZ_128M; |
| |
| /* bmips PCIe outbound windows have a 128MB max size */ |
| if (nwins > BRCM_NUM_PCIE_OUT_WINS) |
| nwins = BRCM_NUM_PCIE_OUT_WINS; |
| for (j = 0; j < nwins; j++, start += SZ_128M) |
| brcm_pcie_set_outbound_win(pcie, j, start, |
| start - entry->offset, |
| SZ_128M); |
| break; |
| } |
| brcm_pcie_set_outbound_win(pcie, num_out_wins, res->start, |
| res->start - entry->offset, |
| resource_size(res)); |
| num_out_wins++; |
| } |
| |
| /* PCIe->SCB endian mode for BAR */ |
| tmp = readl(base + PCIE_RC_CFG_VENDOR_VENDOR_SPECIFIC_REG1); |
| u32p_replace_bits(&tmp, PCIE_RC_CFG_VENDOR_SPCIFIC_REG1_LITTLE_ENDIAN, |
| PCIE_RC_CFG_VENDOR_VENDOR_SPECIFIC_REG1_ENDIAN_MODE_BAR2_MASK); |
| writel(tmp, base + PCIE_RC_CFG_VENDOR_VENDOR_SPECIFIC_REG1); |
| |
| return 0; |
| } |
| |
| static int brcm_pcie_start_link(struct brcm_pcie *pcie) |
| { |
| struct device *dev = pcie->dev; |
| void __iomem *base = pcie->base; |
| u16 nlw, cls, lnksta; |
| bool ssc_good = false; |
| u32 tmp; |
| int ret, i; |
| |
| /* Unassert the fundamental reset */ |
| pcie->perst_set(pcie, 0); |
| |
| /* |
| * Wait for 100ms after PERST# deassertion; see PCIe CEM specification |
| * sections 2.2, PCIe r5.0, 6.6.1. |
| */ |
| msleep(100); |
| |
| /* |
| * Give the RC/EP even more time to wake up, before trying to |
| * configure RC. Intermittently check status for link-up, up to a |
| * total of 100ms. |
| */ |
| for (i = 0; i < 100 && !brcm_pcie_link_up(pcie); i += 5) |
| msleep(5); |
| |
| if (!brcm_pcie_link_up(pcie)) { |
| dev_err(dev, "link down\n"); |
| return -ENODEV; |
| } |
| |
| if (pcie->gen) |
| brcm_pcie_set_gen(pcie, pcie->gen); |
| |
| if (pcie->ssc) { |
| ret = brcm_pcie_set_ssc(pcie); |
| if (ret == 0) |
| ssc_good = true; |
| else |
| dev_err(dev, "failed attempt to enter ssc mode\n"); |
| } |
| |
| lnksta = readw(base + BRCM_PCIE_CAP_REGS + PCI_EXP_LNKSTA); |
| cls = FIELD_GET(PCI_EXP_LNKSTA_CLS, lnksta); |
| nlw = FIELD_GET(PCI_EXP_LNKSTA_NLW, lnksta); |
| dev_info(dev, "link up, %s x%u %s\n", |
| pci_speed_string(pcie_link_speed[cls]), nlw, |
| ssc_good ? "(SSC)" : "(!SSC)"); |
| |
| /* |
| * Refclk from RC should be gated with CLKREQ# input when ASPM L0s,L1 |
| * is enabled => setting the CLKREQ_DEBUG_ENABLE field to 1. |
| */ |
| tmp = readl(base + PCIE_MISC_HARD_PCIE_HARD_DEBUG); |
| tmp |= PCIE_MISC_HARD_PCIE_HARD_DEBUG_CLKREQ_DEBUG_ENABLE_MASK; |
| writel(tmp, base + PCIE_MISC_HARD_PCIE_HARD_DEBUG); |
| |
| return 0; |
| } |
| |
| static const char * const supplies[] = { |
| "vpcie3v3", |
| "vpcie3v3aux", |
| "vpcie12v", |
| }; |
| |
| static void *alloc_subdev_regulators(struct device *dev) |
| { |
| const size_t size = sizeof(struct subdev_regulators) + |
| sizeof(struct regulator_bulk_data) * ARRAY_SIZE(supplies); |
| struct subdev_regulators *sr; |
| int i; |
| |
| sr = devm_kzalloc(dev, size, GFP_KERNEL); |
| if (sr) { |
| sr->num_supplies = ARRAY_SIZE(supplies); |
| for (i = 0; i < ARRAY_SIZE(supplies); i++) |
| sr->supplies[i].supply = supplies[i]; |
| } |
| |
| return sr; |
| } |
| |
| static int brcm_pcie_add_bus(struct pci_bus *bus) |
| { |
| struct brcm_pcie *pcie = bus->sysdata; |
| struct device *dev = &bus->dev; |
| struct subdev_regulators *sr; |
| int ret; |
| |
| if (!bus->parent || !pci_is_root_bus(bus->parent)) |
| return 0; |
| |
| if (dev->of_node) { |
| sr = alloc_subdev_regulators(dev); |
| if (!sr) { |
| dev_info(dev, "Can't allocate regulators for downstream device\n"); |
| goto no_regulators; |
| } |
| |
| pcie->sr = sr; |
| |
| ret = regulator_bulk_get(dev, sr->num_supplies, sr->supplies); |
| if (ret) { |
| dev_info(dev, "No regulators for downstream device\n"); |
| goto no_regulators; |
| } |
| |
| ret = regulator_bulk_enable(sr->num_supplies, sr->supplies); |
| if (ret) { |
| dev_err(dev, "Can't enable regulators for downstream device\n"); |
| regulator_bulk_free(sr->num_supplies, sr->supplies); |
| pcie->sr = NULL; |
| } |
| } |
| |
| no_regulators: |
| brcm_pcie_start_link(pcie); |
| return 0; |
| } |
| |
| static void brcm_pcie_remove_bus(struct pci_bus *bus) |
| { |
| struct brcm_pcie *pcie = bus->sysdata; |
| struct subdev_regulators *sr = pcie->sr; |
| struct device *dev = &bus->dev; |
| |
| if (!sr) |
| return; |
| |
| if (regulator_bulk_disable(sr->num_supplies, sr->supplies)) |
| dev_err(dev, "Failed to disable regulators for downstream device\n"); |
| regulator_bulk_free(sr->num_supplies, sr->supplies); |
| pcie->sr = NULL; |
| } |
| |
| /* L23 is a low-power PCIe link state */ |
| static void brcm_pcie_enter_l23(struct brcm_pcie *pcie) |
| { |
| void __iomem *base = pcie->base; |
| int l23, i; |
| u32 tmp; |
| |
| /* Assert request for L23 */ |
| tmp = readl(base + PCIE_MISC_PCIE_CTRL); |
| u32p_replace_bits(&tmp, 1, PCIE_MISC_PCIE_CTRL_PCIE_L23_REQUEST_MASK); |
| writel(tmp, base + PCIE_MISC_PCIE_CTRL); |
| |
| /* Wait up to 36 msec for L23 */ |
| tmp = readl(base + PCIE_MISC_PCIE_STATUS); |
| l23 = FIELD_GET(PCIE_MISC_PCIE_STATUS_PCIE_LINK_IN_L23_MASK, tmp); |
| for (i = 0; i < 15 && !l23; i++) { |
| usleep_range(2000, 2400); |
| tmp = readl(base + PCIE_MISC_PCIE_STATUS); |
| l23 = FIELD_GET(PCIE_MISC_PCIE_STATUS_PCIE_LINK_IN_L23_MASK, |
| tmp); |
| } |
| |
| if (!l23) |
| dev_err(pcie->dev, "failed to enter low-power link state\n"); |
| } |
| |
| static int brcm_phy_cntl(struct brcm_pcie *pcie, const int start) |
| { |
| static const u32 shifts[PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_NFLDS] = { |
| PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_PWRDN_SHIFT, |
| PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_RESET_SHIFT, |
| PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_DIG_RESET_SHIFT,}; |
| static const u32 masks[PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_NFLDS] = { |
| PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_PWRDN_MASK, |
| PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_RESET_MASK, |
| PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_DIG_RESET_MASK,}; |
| const int beg = start ? 0 : PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_NFLDS - 1; |
| const int end = start ? PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_NFLDS : -1; |
| u32 tmp, combined_mask = 0; |
| u32 val; |
| void __iomem *base = pcie->base; |
| int i, ret; |
| |
| for (i = beg; i != end; start ? i++ : i--) { |
| val = start ? BIT_MASK(shifts[i]) : 0; |
| tmp = readl(base + PCIE_DVT_PMU_PCIE_PHY_CTRL); |
| tmp = (tmp & ~masks[i]) | (val & masks[i]); |
| writel(tmp, base + PCIE_DVT_PMU_PCIE_PHY_CTRL); |
| usleep_range(50, 200); |
| combined_mask |= masks[i]; |
| } |
| |
| tmp = readl(base + PCIE_DVT_PMU_PCIE_PHY_CTRL); |
| val = start ? combined_mask : 0; |
| |
| ret = (tmp & combined_mask) == val ? 0 : -EIO; |
| if (ret) |
| dev_err(pcie->dev, "failed to %s phy\n", (start ? "start" : "stop")); |
| |
| return ret; |
| } |
| |
| static inline int brcm_phy_start(struct brcm_pcie *pcie) |
| { |
| return pcie->rescal ? brcm_phy_cntl(pcie, 1) : 0; |
| } |
| |
| static inline int brcm_phy_stop(struct brcm_pcie *pcie) |
| { |
| return pcie->rescal ? brcm_phy_cntl(pcie, 0) : 0; |
| } |
| |
| static void brcm_pcie_turn_off(struct brcm_pcie *pcie) |
| { |
| void __iomem *base = pcie->base; |
| int tmp; |
| |
| if (brcm_pcie_link_up(pcie)) |
| brcm_pcie_enter_l23(pcie); |
| /* Assert fundamental reset */ |
| pcie->perst_set(pcie, 1); |
| |
| /* Deassert request for L23 in case it was asserted */ |
| tmp = readl(base + PCIE_MISC_PCIE_CTRL); |
| u32p_replace_bits(&tmp, 0, PCIE_MISC_PCIE_CTRL_PCIE_L23_REQUEST_MASK); |
| writel(tmp, base + PCIE_MISC_PCIE_CTRL); |
| |
| /* Turn off SerDes */ |
| tmp = readl(base + PCIE_MISC_HARD_PCIE_HARD_DEBUG); |
| u32p_replace_bits(&tmp, 1, PCIE_MISC_HARD_PCIE_HARD_DEBUG_SERDES_IDDQ_MASK); |
| writel(tmp, base + PCIE_MISC_HARD_PCIE_HARD_DEBUG); |
| |
| /* Shutdown PCIe bridge */ |
| pcie->bridge_sw_init_set(pcie, 1); |
| } |
| |
| static int pci_dev_may_wakeup(struct pci_dev *dev, void *data) |
| { |
| bool *ret = data; |
| |
| if (device_may_wakeup(&dev->dev)) { |
| *ret = true; |
| dev_info(&dev->dev, "Possible wake-up device; regulators will not be disabled\n"); |
| } |
| return (int) *ret; |
| } |
| |
| static int brcm_pcie_suspend_noirq(struct device *dev) |
| { |
| struct brcm_pcie *pcie = dev_get_drvdata(dev); |
| struct pci_host_bridge *bridge = pci_host_bridge_from_priv(pcie); |
| int ret; |
| |
| brcm_pcie_turn_off(pcie); |
| /* |
| * If brcm_phy_stop() returns an error, just dev_err(). If we |
| * return the error it will cause the suspend to fail and this is a |
| * forgivable offense that will probably be erased on resume. |
| */ |
| if (brcm_phy_stop(pcie)) |
| dev_err(dev, "Could not stop phy for suspend\n"); |
| |
| ret = reset_control_rearm(pcie->rescal); |
| if (ret) { |
| dev_err(dev, "Could not rearm rescal reset\n"); |
| return ret; |
| } |
| |
| if (pcie->sr) { |
| /* |
| * Now turn off the regulators, but if at least one |
| * downstream device is enabled as a wake-up source, do not |
| * turn off regulators. |
| */ |
| pcie->ep_wakeup_capable = false; |
| pci_walk_bus(bridge->bus, pci_dev_may_wakeup, |
| &pcie->ep_wakeup_capable); |
| if (!pcie->ep_wakeup_capable) { |
| ret = regulator_bulk_disable(pcie->sr->num_supplies, |
| pcie->sr->supplies); |
| if (ret) { |
| dev_err(dev, "Could not turn off regulators\n"); |
| reset_control_reset(pcie->rescal); |
| return ret; |
| } |
| } |
| } |
| clk_disable_unprepare(pcie->clk); |
| |
| return 0; |
| } |
| |
| static int brcm_pcie_resume_noirq(struct device *dev) |
| { |
| struct brcm_pcie *pcie = dev_get_drvdata(dev); |
| void __iomem *base; |
| u32 tmp; |
| int ret; |
| |
| base = pcie->base; |
| ret = clk_prepare_enable(pcie->clk); |
| if (ret) |
| return ret; |
| |
| ret = reset_control_reset(pcie->rescal); |
| if (ret) |
| goto err_disable_clk; |
| |
| ret = brcm_phy_start(pcie); |
| if (ret) |
| goto err_reset; |
| |
| /* Take bridge out of reset so we can access the SERDES reg */ |
| pcie->bridge_sw_init_set(pcie, 0); |
| |
| /* SERDES_IDDQ = 0 */ |
| tmp = readl(base + PCIE_MISC_HARD_PCIE_HARD_DEBUG); |
| u32p_replace_bits(&tmp, 0, PCIE_MISC_HARD_PCIE_HARD_DEBUG_SERDES_IDDQ_MASK); |
| writel(tmp, base + PCIE_MISC_HARD_PCIE_HARD_DEBUG); |
| |
| /* wait for serdes to be stable */ |
| udelay(100); |
| |
| ret = brcm_pcie_setup(pcie); |
| if (ret) |
| goto err_reset; |
| |
| if (pcie->sr) { |
| if (pcie->ep_wakeup_capable) { |
| /* |
| * We are resuming from a suspend. In the suspend we |
| * did not disable the power supplies, so there is |
| * no need to enable them (and falsely increase their |
| * usage count). |
| */ |
| pcie->ep_wakeup_capable = false; |
| } else { |
| ret = regulator_bulk_enable(pcie->sr->num_supplies, |
| pcie->sr->supplies); |
| if (ret) { |
| dev_err(dev, "Could not turn on regulators\n"); |
| goto err_reset; |
| } |
| } |
| } |
| |
| ret = brcm_pcie_start_link(pcie); |
| if (ret) |
| goto err_regulator; |
| |
| if (pcie->msi) |
| brcm_msi_set_regs(pcie->msi); |
| |
| return 0; |
| |
| err_regulator: |
| if (pcie->sr) |
| regulator_bulk_disable(pcie->sr->num_supplies, pcie->sr->supplies); |
| err_reset: |
| reset_control_rearm(pcie->rescal); |
| err_disable_clk: |
| clk_disable_unprepare(pcie->clk); |
| return ret; |
| } |
| |
| static void __brcm_pcie_remove(struct brcm_pcie *pcie) |
| { |
| brcm_msi_remove(pcie); |
| brcm_pcie_turn_off(pcie); |
| if (brcm_phy_stop(pcie)) |
| dev_err(pcie->dev, "Could not stop phy\n"); |
| if (reset_control_rearm(pcie->rescal)) |
| dev_err(pcie->dev, "Could not rearm rescal reset\n"); |
| clk_disable_unprepare(pcie->clk); |
| } |
| |
| static void brcm_pcie_remove(struct platform_device *pdev) |
| { |
| struct brcm_pcie *pcie = platform_get_drvdata(pdev); |
| struct pci_host_bridge *bridge = pci_host_bridge_from_priv(pcie); |
| |
| pci_stop_root_bus(bridge->bus); |
| pci_remove_root_bus(bridge->bus); |
| __brcm_pcie_remove(pcie); |
| } |
| |
| static const int pcie_offsets[] = { |
| [RGR1_SW_INIT_1] = 0x9210, |
| [EXT_CFG_INDEX] = 0x9000, |
| [EXT_CFG_DATA] = 0x9004, |
| }; |
| |
| static const int pcie_offsets_bmips_7425[] = { |
| [RGR1_SW_INIT_1] = 0x8010, |
| [EXT_CFG_INDEX] = 0x8300, |
| [EXT_CFG_DATA] = 0x8304, |
| }; |
| |
| static const struct pcie_cfg_data generic_cfg = { |
| .offsets = pcie_offsets, |
| .type = GENERIC, |
| .perst_set = brcm_pcie_perst_set_generic, |
| .bridge_sw_init_set = brcm_pcie_bridge_sw_init_set_generic, |
| }; |
| |
| static const struct pcie_cfg_data bcm7425_cfg = { |
| .offsets = pcie_offsets_bmips_7425, |
| .type = BCM7425, |
| .perst_set = brcm_pcie_perst_set_generic, |
| .bridge_sw_init_set = brcm_pcie_bridge_sw_init_set_generic, |
| }; |
| |
| static const struct pcie_cfg_data bcm7435_cfg = { |
| .offsets = pcie_offsets, |
| .type = BCM7435, |
| .perst_set = brcm_pcie_perst_set_generic, |
| .bridge_sw_init_set = brcm_pcie_bridge_sw_init_set_generic, |
| }; |
| |
| static const struct pcie_cfg_data bcm4908_cfg = { |
| .offsets = pcie_offsets, |
| .type = BCM4908, |
| .perst_set = brcm_pcie_perst_set_4908, |
| .bridge_sw_init_set = brcm_pcie_bridge_sw_init_set_generic, |
| }; |
| |
| static const int pcie_offset_bcm7278[] = { |
| [RGR1_SW_INIT_1] = 0xc010, |
| [EXT_CFG_INDEX] = 0x9000, |
| [EXT_CFG_DATA] = 0x9004, |
| }; |
| |
| static const struct pcie_cfg_data bcm7278_cfg = { |
| .offsets = pcie_offset_bcm7278, |
| .type = BCM7278, |
| .perst_set = brcm_pcie_perst_set_7278, |
| .bridge_sw_init_set = brcm_pcie_bridge_sw_init_set_7278, |
| }; |
| |
| static const struct pcie_cfg_data bcm2711_cfg = { |
| .offsets = pcie_offsets, |
| .type = BCM2711, |
| .perst_set = brcm_pcie_perst_set_generic, |
| .bridge_sw_init_set = brcm_pcie_bridge_sw_init_set_generic, |
| }; |
| |
| static const struct of_device_id brcm_pcie_match[] = { |
| { .compatible = "brcm,bcm2711-pcie", .data = &bcm2711_cfg }, |
| { .compatible = "brcm,bcm4908-pcie", .data = &bcm4908_cfg }, |
| { .compatible = "brcm,bcm7211-pcie", .data = &generic_cfg }, |
| { .compatible = "brcm,bcm7278-pcie", .data = &bcm7278_cfg }, |
| { .compatible = "brcm,bcm7216-pcie", .data = &bcm7278_cfg }, |
| { .compatible = "brcm,bcm7445-pcie", .data = &generic_cfg }, |
| { .compatible = "brcm,bcm7435-pcie", .data = &bcm7435_cfg }, |
| { .compatible = "brcm,bcm7425-pcie", .data = &bcm7425_cfg }, |
| {}, |
| }; |
| |
| static struct pci_ops brcm_pcie_ops = { |
| .map_bus = brcm_pcie_map_bus, |
| .read = pci_generic_config_read, |
| .write = pci_generic_config_write, |
| .add_bus = brcm_pcie_add_bus, |
| .remove_bus = brcm_pcie_remove_bus, |
| }; |
| |
| static struct pci_ops brcm7425_pcie_ops = { |
| .map_bus = brcm7425_pcie_map_bus, |
| .read = pci_generic_config_read32, |
| .write = pci_generic_config_write32, |
| .add_bus = brcm_pcie_add_bus, |
| .remove_bus = brcm_pcie_remove_bus, |
| }; |
| |
| static int brcm_pcie_probe(struct platform_device *pdev) |
| { |
| struct device_node *np = pdev->dev.of_node, *msi_np; |
| struct pci_host_bridge *bridge; |
| const struct pcie_cfg_data *data; |
| struct brcm_pcie *pcie; |
| int ret; |
| |
| bridge = devm_pci_alloc_host_bridge(&pdev->dev, sizeof(*pcie)); |
| if (!bridge) |
| return -ENOMEM; |
| |
| data = of_device_get_match_data(&pdev->dev); |
| if (!data) { |
| pr_err("failed to look up compatible string\n"); |
| return -EINVAL; |
| } |
| |
| pcie = pci_host_bridge_priv(bridge); |
| pcie->dev = &pdev->dev; |
| pcie->np = np; |
| pcie->reg_offsets = data->offsets; |
| pcie->type = data->type; |
| pcie->perst_set = data->perst_set; |
| pcie->bridge_sw_init_set = data->bridge_sw_init_set; |
| |
| pcie->base = devm_platform_ioremap_resource(pdev, 0); |
| if (IS_ERR(pcie->base)) |
| return PTR_ERR(pcie->base); |
| |
| pcie->clk = devm_clk_get_optional(&pdev->dev, "sw_pcie"); |
| if (IS_ERR(pcie->clk)) |
| return PTR_ERR(pcie->clk); |
| |
| ret = of_pci_get_max_link_speed(np); |
| pcie->gen = (ret < 0) ? 0 : ret; |
| |
| pcie->ssc = of_property_read_bool(np, "brcm,enable-ssc"); |
| |
| ret = clk_prepare_enable(pcie->clk); |
| if (ret) { |
| dev_err(&pdev->dev, "could not enable clock\n"); |
| return ret; |
| } |
| pcie->rescal = devm_reset_control_get_optional_shared(&pdev->dev, "rescal"); |
| if (IS_ERR(pcie->rescal)) { |
| clk_disable_unprepare(pcie->clk); |
| return PTR_ERR(pcie->rescal); |
| } |
| pcie->perst_reset = devm_reset_control_get_optional_exclusive(&pdev->dev, "perst"); |
| if (IS_ERR(pcie->perst_reset)) { |
| clk_disable_unprepare(pcie->clk); |
| return PTR_ERR(pcie->perst_reset); |
| } |
| |
| ret = reset_control_reset(pcie->rescal); |
| if (ret) |
| dev_err(&pdev->dev, "failed to deassert 'rescal'\n"); |
| |
| ret = brcm_phy_start(pcie); |
| if (ret) { |
| reset_control_rearm(pcie->rescal); |
| clk_disable_unprepare(pcie->clk); |
| return ret; |
| } |
| |
| ret = brcm_pcie_setup(pcie); |
| if (ret) |
| goto fail; |
| |
| pcie->hw_rev = readl(pcie->base + PCIE_MISC_REVISION); |
| if (pcie->type == BCM4908 && pcie->hw_rev >= BRCM_PCIE_HW_REV_3_20) { |
| dev_err(pcie->dev, "hardware revision with unsupported PERST# setup\n"); |
| ret = -ENODEV; |
| goto fail; |
| } |
| |
| msi_np = of_parse_phandle(pcie->np, "msi-parent", 0); |
| if (pci_msi_enabled() && msi_np == pcie->np) { |
| ret = brcm_pcie_enable_msi(pcie); |
| if (ret) { |
| dev_err(pcie->dev, "probe of internal MSI failed"); |
| goto fail; |
| } |
| } |
| |
| bridge->ops = pcie->type == BCM7425 ? &brcm7425_pcie_ops : &brcm_pcie_ops; |
| bridge->sysdata = pcie; |
| |
| platform_set_drvdata(pdev, pcie); |
| |
| ret = pci_host_probe(bridge); |
| if (!ret && !brcm_pcie_link_up(pcie)) |
| ret = -ENODEV; |
| |
| if (ret) { |
| brcm_pcie_remove(pdev); |
| return ret; |
| } |
| |
| return 0; |
| |
| fail: |
| __brcm_pcie_remove(pcie); |
| return ret; |
| } |
| |
| MODULE_DEVICE_TABLE(of, brcm_pcie_match); |
| |
| static const struct dev_pm_ops brcm_pcie_pm_ops = { |
| .suspend_noirq = brcm_pcie_suspend_noirq, |
| .resume_noirq = brcm_pcie_resume_noirq, |
| }; |
| |
| static struct platform_driver brcm_pcie_driver = { |
| .probe = brcm_pcie_probe, |
| .remove_new = brcm_pcie_remove, |
| .driver = { |
| .name = "brcm-pcie", |
| .of_match_table = brcm_pcie_match, |
| .pm = &brcm_pcie_pm_ops, |
| }, |
| }; |
| module_platform_driver(brcm_pcie_driver); |
| |
| MODULE_LICENSE("GPL"); |
| MODULE_DESCRIPTION("Broadcom STB PCIe RC driver"); |
| MODULE_AUTHOR("Broadcom"); |