blob: 7f9d8c7a635a6ffc1cb4ad3a7987929d28391488 [file] [log] [blame]
# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
%YAML 1.2
---
$id: http://devicetree.org/schemas/sound/cirrus,cs42l43.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: Cirrus Logic CS42L43 Audio CODEC
maintainers:
- patches@opensource.cirrus.com
description: |
The CS42L43 is an audio CODEC with integrated MIPI SoundWire interface
(Version 1.2.1 compliant), I2C, SPI, and I2S/TDM interfaces designed
for portable applications. It provides a high dynamic range, stereo
DAC for headphone output, two integrated Class D amplifiers for
loudspeakers, and two ADCs for wired headset microphone input or
stereo line input. PDM inputs are provided for digital microphones.
allOf:
- $ref: dai-common.yaml#
properties:
compatible:
enum:
- cirrus,cs42l43
reg:
maxItems: 1
vdd-p-supply:
description:
Power supply for the high voltage interface.
vdd-a-supply:
description:
Power supply for internal analog circuits.
vdd-d-supply:
description:
Power supply for internal digital circuits. Can be internally supplied.
vdd-io-supply:
description:
Power supply for external interface and internal digital logic.
vdd-cp-supply:
description:
Power supply for the amplifier 3 and 4 charge pump.
vdd-amp-supply:
description:
Power supply for amplifier 1 and 2.
reset-gpios:
maxItems: 1
interrupt-controller: true
"#interrupt-cells":
const: 2
interrupts:
maxItems: 1
"#sound-dai-cells":
const: 1
clocks:
items:
- description: Synchronous audio clock provided on mclk_in.
clock-names:
const: mclk
cirrus,bias-low:
type: boolean
description:
Select a 1.8V headset micbias rather than 2.8V.
cirrus,bias-sense-microamp:
description:
Current at which the headset micbias sense clamp will engage, 0 to
disable.
enum: [ 0, 14, 24, 43, 52, 61, 71, 90, 99 ]
default: 14
cirrus,bias-ramp-ms:
description:
Time in milliseconds the hardware allows for the headset micbias to
ramp up.
enum: [ 10, 40, 90, 170 ]
default: 170
cirrus,detect-us:
description:
Time in microseconds the type detection will run for. Long values will
cause more audible effects, but give more accurate detection.
enum: [ 20, 100, 1000, 10000, 50000, 75000, 100000, 200000 ]
default: 1000
cirrus,button-automute:
type: boolean
description:
Enable the hardware automuting of decimator 1 when a headset button is
pressed.
cirrus,buttons-ohms:
description:
Impedance in Ohms for each headset button, these should be listed in
ascending order.
minItems: 1
maxItems: 6
cirrus,tip-debounce-ms:
description:
Software debounce on tip sense triggering in milliseconds.
default: 0
cirrus,tip-invert:
type: boolean
description:
Indicates tip detect polarity, inverted implies open-circuit whilst the
jack is inserted.
cirrus,tip-disable-pullup:
type: boolean
description:
Indicates if the internal pullup on the tip detect should be disabled.
cirrus,tip-fall-db-ms:
description:
Time in milliseconds a falling edge on the tip detect should be hardware
debounced for. Note the falling edge is considered after the invert.
enum: [ 0, 125, 250, 500, 750, 1000, 1250, 1500 ]
default: 500
cirrus,tip-rise-db-ms:
description:
Time in milliseconds a rising edge on the tip detect should be hardware
debounced for. Note the rising edge is considered after the invert.
enum: [ 0, 125, 250, 500, 750, 1000, 1250, 1500 ]
default: 500
cirrus,use-ring-sense:
type: boolean
description:
Indicates if the ring sense should be used.
cirrus,ring-invert:
type: boolean
description:
Indicates ring detect polarity, inverted implies open-circuit whilst the
jack is inserted.
cirrus,ring-disable-pullup:
type: boolean
description:
Indicates if the internal pullup on the ring detect should be disabled.
cirrus,ring-fall-db-ms:
description:
Time in milliseconds a falling edge on the ring detect should be hardware
debounced for. Note the falling edge is considered after the invert.
enum: [ 0, 125, 250, 500, 750, 1000, 1250, 1500 ]
default: 500
cirrus,ring-rise-db-ms:
description:
Time in milliseconds a rising edge on the ring detect should be hardware
debounced for. Note the rising edge is considered after the invert.
enum: [ 0, 125, 250, 500, 750, 1000, 1250, 1500 ]
default: 500
pinctrl:
type: object
$ref: /schemas/pinctrl/pinctrl.yaml#
additionalProperties: false
properties:
gpio-controller: true
"#gpio-cells":
const: 2
gpio-ranges:
items:
- description: A phandle to the CODEC pinctrl node
minimum: 0
- const: 0
- const: 0
- const: 3
patternProperties:
"-state$":
oneOf:
- $ref: "#/$defs/cirrus-cs42l43-state"
- patternProperties:
"-pins$":
$ref: "#/$defs/cirrus-cs42l43-state"
additionalProperties: false
spi:
type: object
$ref: /schemas/spi/spi-controller.yaml#
unevaluatedProperties: false
$defs:
cirrus-cs42l43-state:
type: object
allOf:
- $ref: /schemas/pinctrl/pincfg-node.yaml#
- $ref: /schemas/pinctrl/pinmux-node.yaml#
oneOf:
- required: [ groups ]
- required: [ pins ]
additionalProperties: false
properties:
groups:
enum: [ gpio1, gpio2, gpio3, asp, pdmout2, pdmout1, i2c, spi ]
pins:
enum: [ gpio1, gpio2, gpio3,
asp_dout, asp_fsync, asp_bclk,
pdmout2_clk, pdmout2_data, pdmout1_clk, pdmout1_data,
i2c_sda, i2c_scl,
spi_miso, spi_sck, spi_ssb ]
function:
enum: [ gpio, spdif, irq, mic-shutter, spk-shutter ]
drive-strength:
description: Set drive strength in mA
enum: [ 1, 2, 4, 8, 9, 10, 12, 16 ]
input-debounce:
description: Set input debounce in uS
enum: [ 0, 85 ]
required:
- compatible
- reg
- vdd-p-supply
- vdd-a-supply
- vdd-io-supply
- vdd-cp-supply
additionalProperties: false
examples:
- |
#include <dt-bindings/interrupt-controller/irq.h>
i2c {
#address-cells = <1>;
#size-cells = <0>;
cs42l43: codec@1a {
compatible = "cirrus,cs42l43";
reg = <0x1a>;
vdd-p-supply = <&vdd5v0>;
vdd-a-supply = <&vdd1v8>;
vdd-io-supply = <&vdd1v8>;
vdd-cp-supply = <&vdd1v8>;
vdd-amp-supply = <&vdd5v0>;
reset-gpios = <&gpio 0>;
interrupt-controller;
#interrupt-cells = <2>;
interrupt-parent = <&gpio>;
interrupts = <56 IRQ_TYPE_LEVEL_LOW>;
#sound-dai-cells = <1>;
clocks = <&clks 0>;
clock-names = "mclk";
cs42l43_pins: pinctrl {
gpio-controller;
#gpio-cells = <2>;
gpio-ranges = <&cs42l43_pins 0 0 3>;
pinctrl-names = "default";
pinctrl-0 = <&pinsettings>;
pinsettings: default-state {
shutter-pins {
groups = "gpio3";
function = "mic-shutter";
};
};
};
spi {
#address-cells = <1>;
#size-cells = <0>;
cs-gpios = <&cs42l43_pins 1 0>;
sensor@0 {
compatible = "bosch,bme680";
reg = <0>;
spi-max-frequency = <1400000>;
};
};
};
};