blob: 6f0811587142d2725db959d100e7229c6ca82f02 [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/*
* Copyright 2022 Toradex
*/
#include <dt-bindings/phy/phy-imx8-pcie.h>
#include <dt-bindings/pwm/pwm.h>
#include "imx8mm.dtsi"
/ {
chosen {
stdout-path = &uart1;
};
aliases {
rtc0 = &rtc_i2c;
rtc1 = &snvs_rtc;
};
backlight: backlight {
compatible = "pwm-backlight";
brightness-levels = <0 45 63 88 119 158 203 255>;
default-brightness-level = <4>;
/* Verdin I2S_2_D_OUT (DSI_1_BKL_EN/DSI_1_BKL_EN_LVDS, SODIMM 46) */
enable-gpios = <&gpio3 24 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2s_2_d_out_dsi_1_bkl_en>;
power-supply = <&reg_3p3v>;
/* Verdin PWM_3_DSI/PWM_3_DSI_LVDS (SODIMM 19) */
pwms = <&pwm1 0 6666667 PWM_POLARITY_INVERTED>;
status = "disabled";
};
/* Fixed clock dedicated to SPI CAN controller */
clk40m: oscillator {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <40000000>;
};
gpio-keys {
compatible = "gpio-keys";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_gpio_keys>;
key-wakeup {
debounce-interval = <10>;
/* Verdin CTRL_WAKE1_MICO# (SODIMM 252) */
gpios = <&gpio4 28 GPIO_ACTIVE_LOW>;
label = "Wake-Up";
linux,code = <KEY_WAKEUP>;
wakeup-source;
};
};
hdmi_connector: hdmi-connector {
compatible = "hdmi-connector";
ddc-i2c-bus = <&i2c2>;
/* Verdin PWM_3_DSI (SODIMM 19) */
hpd-gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>;
label = "hdmi";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pwm_3_dsi_hpd_gpio>;
type = "a";
status = "disabled";
};
panel_lvds: panel-lvds {
compatible = "panel-lvds";
backlight = <&backlight>;
data-mapping = "vesa-24";
status = "disabled";
};
/* Carrier Board Supplies */
reg_1p8v: regulator-1p8v {
compatible = "regulator-fixed";
regulator-max-microvolt = <1800000>;
regulator-min-microvolt = <1800000>;
regulator-name = "+V1.8_SW";
};
reg_3p3v: regulator-3p3v {
compatible = "regulator-fixed";
regulator-max-microvolt = <3300000>;
regulator-min-microvolt = <3300000>;
regulator-name = "+V3.3_SW";
};
reg_5p0v: regulator-5p0v {
compatible = "regulator-fixed";
regulator-max-microvolt = <5000000>;
regulator-min-microvolt = <5000000>;
regulator-name = "+V5_SW";
};
/* Non PMIC On-module Supplies */
reg_ethphy: regulator-ethphy {
compatible = "regulator-fixed";
enable-active-high;
gpio = <&gpio2 20 GPIO_ACTIVE_HIGH>; /* PMIC_EN_ETH */
off-on-delay-us = <500000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_reg_eth>;
regulator-always-on;
regulator-boot-on;
regulator-max-microvolt = <3300000>;
regulator-min-microvolt = <3300000>;
regulator-name = "On-module +V3.3_ETH";
startup-delay-us = <200000>;
};
reg_usb_otg1_vbus: regulator-usb-otg1 {
compatible = "regulator-fixed";
enable-active-high;
/* Verdin USB_1_EN (SODIMM 155) */
gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_reg_usb1_en>;
regulator-max-microvolt = <5000000>;
regulator-min-microvolt = <5000000>;
regulator-name = "USB_1_EN";
};
reg_usb_otg2_vbus: regulator-usb-otg2 {
compatible = "regulator-fixed";
enable-active-high;
/* Verdin USB_2_EN (SODIMM 185) */
gpio = <&gpio1 14 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_reg_usb2_en>;
regulator-max-microvolt = <5000000>;
regulator-min-microvolt = <5000000>;
regulator-name = "USB_2_EN";
};
reg_usdhc2_vmmc: regulator-usdhc2 {
compatible = "regulator-fixed";
enable-active-high;
/* Verdin SD_1_PWR_EN (SODIMM 76) */
gpio = <&gpio3 5 GPIO_ACTIVE_HIGH>;
off-on-delay-us = <100000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usdhc2_pwr_en>;
regulator-max-microvolt = <3300000>;
regulator-min-microvolt = <3300000>;
regulator-name = "+V3.3_SD";
startup-delay-us = <2000>;
};
reserved-memory {
#address-cells = <2>;
#size-cells = <2>;
ranges;
/* Use the kernel configuration settings instead */
/delete-node/ linux,cma;
};
};
&A53_0 {
cpu-supply = <&reg_vdd_arm>;
};
&A53_1 {
cpu-supply = <&reg_vdd_arm>;
};
&A53_2 {
cpu-supply = <&reg_vdd_arm>;
};
&A53_3 {
cpu-supply = <&reg_vdd_arm>;
};
&cpu_alert0 {
temperature = <95000>;
};
&cpu_crit0 {
temperature = <105000>;
};
&ddrc {
operating-points-v2 = <&ddrc_opp_table>;
ddrc_opp_table: opp-table {
compatible = "operating-points-v2";
opp-25000000 {
opp-hz = /bits/ 64 <25000000>;
};
opp-100000000 {
opp-hz = /bits/ 64 <100000000>;
};
opp-750000000 {
opp-hz = /bits/ 64 <750000000>;
};
};
};
/* Verdin SPI_1 */
&ecspi2 {
#address-cells = <1>;
#size-cells = <0>;
cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ecspi2>;
};
/* Verdin CAN_1 (On-module) */
&ecspi3 {
#address-cells = <1>;
#size-cells = <0>;
cs-gpios = <&gpio5 25 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ecspi3>;
status = "okay";
can1: can@0 {
compatible = "microchip,mcp251xfd";
clocks = <&clk40m>;
interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_can1_int>;
reg = <0>;
spi-max-frequency = <8500000>;
};
};
/* Verdin ETH_1 (On-module PHY) */
&fec1 {
fsl,magic-packet;
phy-handle = <&ethphy0>;
phy-mode = "rgmii-id";
phy-supply = <&reg_ethphy>;
pinctrl-names = "default", "sleep";
pinctrl-0 = <&pinctrl_fec1>;
pinctrl-1 = <&pinctrl_fec1_sleep>;
mdio {
#address-cells = <1>;
#size-cells = <0>;
ethphy0: ethernet-phy@7 {
compatible = "ethernet-phy-ieee802.3-c22";
interrupt-parent = <&gpio1>;
interrupts = <10 IRQ_TYPE_LEVEL_LOW>;
micrel,led-mode = <0>;
reg = <7>;
};
};
};
/* Verdin QSPI_1 */
&flexspi {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_flexspi0>;
};
&gpio1 {
gpio-line-names = "SODIMM_216",
"SODIMM_19",
"",
"",
"",
"",
"",
"",
"SODIMM_220",
"SODIMM_222",
"",
"SODIMM_218",
"SODIMM_155",
"SODIMM_157",
"SODIMM_185",
"SODIMM_187";
};
&gpio2 {
gpio-line-names = "",
"",
"",
"",
"",
"",
"",
"",
"",
"",
"",
"",
"SODIMM_84",
"SODIMM_78",
"SODIMM_74",
"SODIMM_80",
"SODIMM_82",
"SODIMM_70",
"SODIMM_72";
};
&gpio5 {
gpio-line-names = "SODIMM_131",
"",
"SODIMM_91",
"SODIMM_16",
"SODIMM_15",
"SODIMM_208",
"SODIMM_137",
"SODIMM_139",
"SODIMM_141",
"SODIMM_143",
"SODIMM_196",
"SODIMM_200",
"SODIMM_198",
"SODIMM_202",
"",
"",
"SODIMM_55",
"SODIMM_53",
"SODIMM_95",
"SODIMM_93",
"SODIMM_14",
"SODIMM_12",
"",
"",
"",
"",
"SODIMM_210",
"SODIMM_212",
"SODIMM_151",
"SODIMM_153";
ctrl-sleep-moci-hog {
gpio-hog;
/* Verdin CTRL_SLEEP_MOCI# (SODIMM 256) */
gpios = <1 GPIO_ACTIVE_HIGH>;
line-name = "CTRL_SLEEP_MOCI#";
output-high;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ctrl_sleep_moci>;
};
};
/* On-module I2C */
&i2c1 {
clock-frequency = <400000>;
pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c1>;
pinctrl-1 = <&pinctrl_i2c1_gpio>;
scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
status = "okay";
pca9450: pmic@25 {
compatible = "nxp,pca9450a";
interrupt-parent = <&gpio1>;
/* PMIC PCA9450 PMIC_nINT GPIO1_IO3 */
interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pmic>;
reg = <0x25>;
/*
* The bootloader is expected to switch on the I2C level shifter for the TLA2024 ADC
* behind this PMIC.
*/
regulators {
reg_vdd_soc: BUCK1 {
nxp,dvs-run-voltage = <850000>;
nxp,dvs-standby-voltage = <800000>;
regulator-always-on;
regulator-boot-on;
regulator-max-microvolt = <850000>;
regulator-min-microvolt = <800000>;
regulator-name = "On-module +VDD_SOC (BUCK1)";
regulator-ramp-delay = <3125>;
};
reg_vdd_arm: BUCK2 {
nxp,dvs-run-voltage = <950000>;
nxp,dvs-standby-voltage = <850000>;
regulator-always-on;
regulator-boot-on;
regulator-max-microvolt = <1050000>;
regulator-min-microvolt = <805000>;
regulator-name = "On-module +VDD_ARM (BUCK2)";
regulator-ramp-delay = <3125>;
};
reg_vdd_dram: BUCK3 {
regulator-always-on;
regulator-boot-on;
regulator-max-microvolt = <1000000>;
regulator-min-microvolt = <805000>;
regulator-name = "On-module +VDD_GPU_VPU_DDR (BUCK3)";
};
reg_vdd_3v3: BUCK4 {
regulator-always-on;
regulator-boot-on;
regulator-max-microvolt = <3300000>;
regulator-min-microvolt = <3300000>;
regulator-name = "On-module +V3.3 (BUCK4)";
};
reg_vdd_1v8: BUCK5 {
regulator-always-on;
regulator-boot-on;
regulator-max-microvolt = <1800000>;
regulator-min-microvolt = <1800000>;
regulator-name = "PWR_1V8_MOCI (BUCK5)";
};
reg_nvcc_dram: BUCK6 {
regulator-always-on;
regulator-boot-on;
regulator-max-microvolt = <1100000>;
regulator-min-microvolt = <1100000>;
regulator-name = "On-module +VDD_DDR (BUCK6)";
};
reg_nvcc_snvs: LDO1 {
regulator-always-on;
regulator-boot-on;
regulator-max-microvolt = <1800000>;
regulator-min-microvolt = <1800000>;
regulator-name = "On-module +V1.8_SNVS (LDO1)";
};
reg_vdd_snvs: LDO2 {
regulator-always-on;
regulator-boot-on;
regulator-max-microvolt = <800000>;
regulator-min-microvolt = <800000>;
regulator-name = "On-module +V0.8_SNVS (LDO2)";
};
reg_vdda: LDO3 {
regulator-always-on;
regulator-boot-on;
regulator-max-microvolt = <1800000>;
regulator-min-microvolt = <1800000>;
regulator-name = "On-module +V1.8A (LDO3)";
};
reg_vdd_phy: LDO4 {
regulator-always-on;
regulator-boot-on;
regulator-max-microvolt = <900000>;
regulator-min-microvolt = <900000>;
regulator-name = "On-module +V0.9_MIPI (LDO4)";
};
reg_nvcc_sd: LDO5 {
regulator-max-microvolt = <3300000>;
regulator-min-microvolt = <1800000>;
regulator-name = "On-module +V3.3_1.8_SD (LDO5)";
};
};
};
rtc_i2c: rtc@32 {
compatible = "epson,rx8130";
reg = <0x32>;
};
adc@49 {
compatible = "ti,ads1015";
reg = <0x49>;
#address-cells = <1>;
#size-cells = <0>;
/* Verdin I2C_1 (ADC_4 - ADC_3) */
channel@0 {
reg = <0>;
ti,datarate = <4>;
ti,gain = <2>;
};
/* Verdin I2C_1 (ADC_4 - ADC_1) */
channel@1 {
reg = <1>;
ti,datarate = <4>;
ti,gain = <2>;
};
/* Verdin I2C_1 (ADC_3 - ADC_1) */
channel@2 {
reg = <2>;
ti,datarate = <4>;
ti,gain = <2>;
};
/* Verdin I2C_1 (ADC_2 - ADC_1) */
channel@3 {
reg = <3>;
ti,datarate = <4>;
ti,gain = <2>;
};
/* Verdin I2C_1 ADC_4 */
channel@4 {
reg = <4>;
ti,datarate = <4>;
ti,gain = <2>;
};
/* Verdin I2C_1 ADC_3 */
channel@5 {
reg = <5>;
ti,datarate = <4>;
ti,gain = <2>;
};
/* Verdin I2C_1 ADC_2 */
channel@6 {
reg = <6>;
ti,datarate = <4>;
ti,gain = <2>;
};
/* Verdin I2C_1 ADC_1 */
channel@7 {
reg = <7>;
ti,datarate = <4>;
ti,gain = <2>;
};
};
eeprom@50 {
compatible = "st,24c02";
pagesize = <16>;
reg = <0x50>;
};
};
/* Verdin I2C_2_DSI */
&i2c2 {
clock-frequency = <10000>;
pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c2>;
pinctrl-1 = <&pinctrl_i2c2_gpio>;
scl-gpios = <&gpio5 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
sda-gpios = <&gpio5 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
status = "disabled";
};
/* Verdin I2C_3_HDMI N/A */
/* Verdin I2C_4_CSI */
&i2c3 {
clock-frequency = <400000>;
pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c3>;
pinctrl-1 = <&pinctrl_i2c3_gpio>;
scl-gpios = <&gpio5 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
sda-gpios = <&gpio5 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
};
/* Verdin I2C_1 */
&i2c4 {
clock-frequency = <400000>;
pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c4>;
pinctrl-1 = <&pinctrl_i2c4_gpio>;
scl-gpios = <&gpio5 20 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
sda-gpios = <&gpio5 21 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
gpio_expander_21: gpio-expander@21 {
compatible = "nxp,pcal6416";
#gpio-cells = <2>;
gpio-controller;
reg = <0x21>;
vcc-supply = <&reg_3p3v>;
status = "disabled";
};
lvds_ti_sn65dsi84: bridge@2c {
compatible = "ti,sn65dsi84";
/* Verdin GPIO_9_DSI (SN65DSI84 IRQ, SODIMM 17, unused) */
/* Verdin GPIO_10_DSI (SODIMM 21) */
enable-gpios = <&gpio3 3 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_gpio_10_dsi>;
reg = <0x2c>;
status = "disabled";
};
/* Current measurement into module VCC */
hwmon: hwmon@40 {
compatible = "ti,ina219";
reg = <0x40>;
shunt-resistor = <10000>;
status = "disabled";
};
hdmi_lontium_lt8912: hdmi@48 {
compatible = "lontium,lt8912b";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_gpio_10_dsi>;
reg = <0x48>;
/* Verdin GPIO_9_DSI (LT8912 INT, SODIMM 17, unused) */
/* Verdin GPIO_10_DSI (SODIMM 21) */
reset-gpios = <&gpio3 3 GPIO_ACTIVE_LOW>;
status = "disabled";
};
atmel_mxt_ts: touch@4a {
compatible = "atmel,maxtouch";
/*
* Verdin GPIO_9_DSI
* (TOUCH_INT#, SODIMM 17, also routed to SN65DSI84 IRQ albeit currently unused)
*/
interrupt-parent = <&gpio3>;
interrupts = <15 IRQ_TYPE_EDGE_FALLING>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_gpio_9_dsi>, <&pinctrl_i2s_2_bclk_touch_reset>;
reg = <0x4a>;
/* Verdin I2S_2_BCLK (TOUCH_RESET#, SODIMM 42) */
reset-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;
status = "disabled";
};
/* Temperature sensor on carrier board */
hwmon_temp: sensor@4f {
compatible = "ti,tmp75c";
reg = <0x4f>;
status = "disabled";
};
/* EEPROM on display adapter (MIPI DSI Display Adapter) */
eeprom_display_adapter: eeprom@50 {
compatible = "st,24c02";
pagesize = <16>;
reg = <0x50>;
status = "disabled";
};
/* EEPROM on carrier board */
eeprom_carrier_board: eeprom@57 {
compatible = "st,24c02";
pagesize = <16>;
reg = <0x57>;
status = "disabled";
};
};
/* Verdin PCIE_1 */
&pcie0 {
assigned-clocks = <&clk IMX8MM_CLK_PCIE1_AUX>,
<&clk IMX8MM_CLK_PCIE1_CTRL>;
assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_50M>,
<&clk IMX8MM_SYS_PLL2_250M>;
assigned-clock-rates = <10000000>, <250000000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pcie0>;
/* PCIE_1_RESET# (SODIMM 244) */
reset-gpio = <&gpio3 19 GPIO_ACTIVE_LOW>;
};
&pcie_phy {
clocks = <&clk IMX8MM_CLK_PCIE1_PHY>;
clock-names = "ref";
fsl,clkreq-unsupported;
fsl,refclk-pad-mode = <IMX8_PCIE_REFCLK_PAD_OUTPUT>;
fsl,tx-deemph-gen1 = <0x2d>;
fsl,tx-deemph-gen2 = <0xf>;
};
/* Verdin PWM_3_DSI */
&pwm1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pwm_1>;
#pwm-cells = <3>;
};
/* Verdin PWM_1 */
&pwm2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pwm_2>;
#pwm-cells = <3>;
};
/* Verdin PWM_2 */
&pwm3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pwm_3>;
#pwm-cells = <3>;
};
/* Verdin I2S_1 */
&sai2 {
#sound-dai-cells = <0>;
assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>;
assigned-clock-rates = <24576000>;
assigned-clocks = <&clk IMX8MM_CLK_SAI2>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_sai2>;
};
&snvs_pwrkey {
status = "okay";
};
/* Verdin UART_3, used as the Linux console */
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>;
};
/* Verdin UART_1 */
&uart2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart2>;
uart-has-rtscts;
};
/* Verdin UART_2 */
&uart3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart3>;
uart-has-rtscts;
};
/*
* Verdin UART_4
* Resource allocated to M4 by default, must not be accessed from Cortex-A35 or you get an OOPS
*/
&uart4 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart4>;
};
/* Verdin USB_1 */
&usbotg1 {
adp-disable;
dr_mode = "otg";
hnp-disable;
samsung,picophy-dc-vol-level-adjust = <7>;
samsung,picophy-pre-emp-curr-control = <3>;
srp-disable;
vbus-supply = <&reg_usb_otg1_vbus>;
};
/* Verdin USB_2 */
&usbotg2 {
dr_mode = "host";
samsung,picophy-dc-vol-level-adjust = <7>;
samsung,picophy-pre-emp-curr-control = <3>;
vbus-supply = <&reg_usb_otg2_vbus>;
};
&usbphynop1 {
vcc-supply = <&reg_vdd_3v3>;
};
&usbphynop2 {
power-domains = <&pgc_otg2>;
vcc-supply = <&reg_vdd_3v3>;
};
/* On-module eMMC */
&usdhc1 {
bus-width = <8>;
keep-power-in-suspend;
non-removable;
pinctrl-names = "default", "state_100mhz", "state_200mhz";
pinctrl-0 = <&pinctrl_usdhc1>;
pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
status = "okay";
};
/* Verdin SD_1 */
&usdhc2 {
bus-width = <4>;
cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
disable-wp;
pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_cd>;
pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_cd>;
pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_cd>;
pinctrl-3 = <&pinctrl_usdhc2_sleep>, <&pinctrl_usdhc2_cd_sleep>;
vmmc-supply = <&reg_usdhc2_vmmc>;
};
&wdog1 {
fsl,ext-reset-output;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_wdog>;
status = "okay";
};
&iomuxc {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_gpio1>, <&pinctrl_gpio2>,
<&pinctrl_gpio3>, <&pinctrl_gpio4>,
<&pinctrl_gpio7>, <&pinctrl_gpio8>,
<&pinctrl_gpio_hog1>, <&pinctrl_gpio_hog2>, <&pinctrl_gpio_hog3>,
<&pinctrl_pmic_tpm_ena>;
pinctrl_can1_int: can1intgrp {
fsl,pins =
<MX8MM_IOMUXC_GPIO1_IO06_GPIO1_IO6 0x146>; /* CAN_1_SPI_INT#_1.8V */
};
pinctrl_can2_int: can2intgrp {
fsl,pins =
<MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x106>; /* CAN_2_SPI_INT#_1.8V, unused */
};
pinctrl_ctrl_sleep_moci: ctrlsleepmocigrp {
fsl,pins =
<MX8MM_IOMUXC_SAI3_TXD_GPIO5_IO1 0x106>; /* SODIMM 256 */
};
pinctrl_ecspi2: ecspi2grp {
fsl,pins =
<MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO 0x6>, /* SODIMM 198 */
<MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI 0x6>, /* SODIMM 200 */
<MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0x6>, /* SODIMM 196 */
<MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13 0x6>; /* SODIMM 202 */
};
pinctrl_ecspi3: ecspi3grp {
fsl,pins =
<MX8MM_IOMUXC_GPIO1_IO05_GPIO1_IO5 0x146>, /* CAN_2_SPI_CS#_1.8V */
<MX8MM_IOMUXC_UART1_RXD_ECSPI3_SCLK 0x6>, /* CAN_SPI_SCK_1.8V */
<MX8MM_IOMUXC_UART1_TXD_ECSPI3_MOSI 0x6>, /* CAN_SPI_MOSI_1.8V */
<MX8MM_IOMUXC_UART2_RXD_ECSPI3_MISO 0x6>, /* CAN_SPI_MISO_1.8V */
<MX8MM_IOMUXC_UART2_TXD_GPIO5_IO25 0x6>; /* CAN_1_SPI_CS_1.8V# */
};
pinctrl_fec1: fec1grp {
fsl,pins =
<MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x3>,
<MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x3>,
<MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91>,
<MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91>,
<MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91>,
<MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91>,
<MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91>,
<MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91>,
<MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f>,
<MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f>,
<MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f>,
<MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f>,
<MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f>,
<MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f>,
<MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10 0x146>;
};
pinctrl_fec1_sleep: fec1-sleepgrp {
fsl,pins =
<MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x3>,
<MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x3>,
<MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91>,
<MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91>,
<MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91>,
<MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91>,
<MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91>,
<MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91>,
<MX8MM_IOMUXC_ENET_TD0_GPIO1_IO21 0x1f>,
<MX8MM_IOMUXC_ENET_TD1_GPIO1_IO20 0x1f>,
<MX8MM_IOMUXC_ENET_TD2_GPIO1_IO19 0x1f>,
<MX8MM_IOMUXC_ENET_TD3_GPIO1_IO18 0x1f>,
<MX8MM_IOMUXC_ENET_TXC_GPIO1_IO23 0x1f>,
<MX8MM_IOMUXC_ENET_TX_CTL_GPIO1_IO22 0x1f>,
<MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10 0x106>;
};
pinctrl_flexspi0: flexspi0grp {
fsl,pins =
<MX8MM_IOMUXC_NAND_ALE_QSPI_A_SCLK 0x106>, /* SODIMM 52 */
<MX8MM_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B 0x106>, /* SODIMM 54 */
<MX8MM_IOMUXC_NAND_CE1_B_QSPI_A_SS1_B 0x106>, /* SODIMM 64 */
<MX8MM_IOMUXC_NAND_DATA00_QSPI_A_DATA0 0x106>, /* SODIMM 56 */
<MX8MM_IOMUXC_NAND_DATA01_QSPI_A_DATA1 0x106>, /* SODIMM 58 */
<MX8MM_IOMUXC_NAND_DATA02_QSPI_A_DATA2 0x106>, /* SODIMM 60 */
<MX8MM_IOMUXC_NAND_DATA03_QSPI_A_DATA3 0x106>, /* SODIMM 62 */
<MX8MM_IOMUXC_NAND_DQS_QSPI_A_DQS 0x106>; /* SODIMM 66 */
};
pinctrl_gpio1: gpio1grp {
fsl,pins =
<MX8MM_IOMUXC_NAND_CE3_B_GPIO3_IO4 0x106>; /* SODIMM 206 */
};
pinctrl_gpio2: gpio2grp {
fsl,pins =
<MX8MM_IOMUXC_SPDIF_EXT_CLK_GPIO5_IO5 0x106>; /* SODIMM 208 */
};
pinctrl_gpio3: gpio3grp {
fsl,pins =
<MX8MM_IOMUXC_UART3_RXD_GPIO5_IO26 0x106>; /* SODIMM 210 */
};
pinctrl_gpio4: gpio4grp {
fsl,pins =
<MX8MM_IOMUXC_UART3_TXD_GPIO5_IO27 0x106>; /* SODIMM 212 */
};
pinctrl_gpio5: gpio5grp {
fsl,pins =
<MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0 0x106>; /* SODIMM 216 */
};
pinctrl_gpio6: gpio6grp {
fsl,pins =
<MX8MM_IOMUXC_GPIO1_IO11_GPIO1_IO11 0x106>; /* SODIMM 218 */
};
pinctrl_gpio7: gpio7grp {
fsl,pins =
<MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x106>; /* SODIMM 220 */
};
pinctrl_gpio8: gpio8grp {
fsl,pins =
<MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x106>; /* SODIMM 222 */
};
/* Verdin GPIO_9_DSI (pulled-up as active-low) */
pinctrl_gpio_9_dsi: gpio9dsigrp {
fsl,pins =
<MX8MM_IOMUXC_NAND_RE_B_GPIO3_IO15 0x146>; /* SODIMM 17 */
};
/* Verdin GPIO_10_DSI (pulled-up as active-low) */
pinctrl_gpio_10_dsi: gpio10dsigrp {
fsl,pins =
<MX8MM_IOMUXC_NAND_CE2_B_GPIO3_IO3 0x146>; /* SODIMM 21 */
};
pinctrl_gpio_hog1: gpiohog1grp {
fsl,pins =
<MX8MM_IOMUXC_SAI1_MCLK_GPIO4_IO20 0x106>, /* SODIMM 88 */
<MX8MM_IOMUXC_SAI1_RXC_GPIO4_IO1 0x106>, /* SODIMM 90 */
<MX8MM_IOMUXC_SAI1_RXD0_GPIO4_IO2 0x106>, /* SODIMM 92 */
<MX8MM_IOMUXC_SAI1_RXD1_GPIO4_IO3 0x106>, /* SODIMM 94 */
<MX8MM_IOMUXC_SAI1_RXD2_GPIO4_IO4 0x106>, /* SODIMM 96 */
<MX8MM_IOMUXC_SAI1_RXD3_GPIO4_IO5 0x106>, /* SODIMM 100 */
<MX8MM_IOMUXC_SAI1_RXFS_GPIO4_IO0 0x106>, /* SODIMM 102 */
<MX8MM_IOMUXC_SAI1_TXC_GPIO4_IO11 0x106>, /* SODIMM 104 */
<MX8MM_IOMUXC_SAI1_TXD0_GPIO4_IO12 0x106>, /* SODIMM 106 */
<MX8MM_IOMUXC_SAI1_TXD1_GPIO4_IO13 0x106>, /* SODIMM 108 */
<MX8MM_IOMUXC_SAI1_TXD2_GPIO4_IO14 0x106>, /* SODIMM 112 */
<MX8MM_IOMUXC_SAI1_TXD3_GPIO4_IO15 0x106>, /* SODIMM 114 */
<MX8MM_IOMUXC_SAI1_TXD4_GPIO4_IO16 0x106>, /* SODIMM 116 */
<MX8MM_IOMUXC_SAI1_TXD6_GPIO4_IO18 0x106>, /* SODIMM 118 */
<MX8MM_IOMUXC_SAI1_TXFS_GPIO4_IO10 0x106>; /* SODIMM 120 */
};
pinctrl_gpio_hog2: gpiohog2grp {
fsl,pins =
<MX8MM_IOMUXC_SAI3_MCLK_GPIO5_IO2 0x106>; /* SODIMM 91 */
};
pinctrl_gpio_hog3: gpiohog3grp {
fsl,pins =
<MX8MM_IOMUXC_GPIO1_IO13_GPIO1_IO13 0x146>, /* SODIMM 157 */
<MX8MM_IOMUXC_GPIO1_IO15_GPIO1_IO15 0x146>; /* SODIMM 187 */
};
pinctrl_gpio_keys: gpiokeysgrp {
fsl,pins =
<MX8MM_IOMUXC_SAI3_RXFS_GPIO4_IO28 0x146>; /* SODIMM 252 */
};
/* On-module I2C */
pinctrl_i2c1: i2c1grp {
fsl,pins =
<MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL 0x40000146>, /* PMIC_I2C_SCL */
<MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA 0x40000146>; /* PMIC_I2C_SDA */
};
pinctrl_i2c1_gpio: i2c1gpiogrp {
fsl,pins =
<MX8MM_IOMUXC_I2C1_SCL_GPIO5_IO14 0x146>, /* PMIC_I2C_SCL */
<MX8MM_IOMUXC_I2C1_SDA_GPIO5_IO15 0x146>; /* PMIC_I2C_SDA */
};
/* Verdin I2C_4_CSI */
pinctrl_i2c2: i2c2grp {
fsl,pins =
<MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL 0x40000146>, /* SODIMM 55 */
<MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA 0x40000146>; /* SODIMM 53 */
};
pinctrl_i2c2_gpio: i2c2gpiogrp {
fsl,pins =
<MX8MM_IOMUXC_I2C2_SCL_GPIO5_IO16 0x146>, /* SODIMM 55 */
<MX8MM_IOMUXC_I2C2_SDA_GPIO5_IO17 0x146>; /* SODIMM 53 */
};
/* Verdin I2C_2_DSI */
pinctrl_i2c3: i2c3grp {
fsl,pins =
<MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL 0x40000146>, /* SODIMM 95 */
<MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x40000146>; /* SODIMM 93 */
};
pinctrl_i2c3_gpio: i2c3gpiogrp {
fsl,pins =
<MX8MM_IOMUXC_I2C3_SCL_GPIO5_IO18 0x146>, /* SODIMM 95 */
<MX8MM_IOMUXC_I2C3_SDA_GPIO5_IO19 0x146>; /* SODIMM 93 */
};
/* Verdin I2C_1 */
pinctrl_i2c4: i2c4grp {
fsl,pins =
<MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL 0x40000146>, /* SODIMM 14 */
<MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA 0x40000146>; /* SODIMM 12 */
};
pinctrl_i2c4_gpio: i2c4gpiogrp {
fsl,pins =
<MX8MM_IOMUXC_I2C4_SCL_GPIO5_IO20 0x146>, /* SODIMM 14 */
<MX8MM_IOMUXC_I2C4_SDA_GPIO5_IO21 0x146>; /* SODIMM 12 */
};
/* Verdin I2S_2_BCLK (TOUCH_RESET#) */
pinctrl_i2s_2_bclk_touch_reset: i2s2bclktouchresetgrp {
fsl,pins =
<MX8MM_IOMUXC_SAI5_RXD2_GPIO3_IO23 0x6>; /* SODIMM 42 */
};
/* Verdin I2S_2_D_OUT shared with SAI5 */
pinctrl_i2s_2_d_out_dsi_1_bkl_en: i2s2doutdsi1bklengrp {
fsl,pins =
<MX8MM_IOMUXC_SAI5_RXD3_GPIO3_IO24 0x6>; /* SODIMM 46 */
};
pinctrl_pcie0: pcie0grp {
fsl,pins =
<MX8MM_IOMUXC_SAI5_RXFS_GPIO3_IO19 0x6>, /* SODIMM 244 */
/* PMIC_EN_PCIe_CLK, unused */
<MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x6>;
};
pinctrl_pmic: pmicirqgrp {
fsl,pins =
<MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x141>; /* PMIC_INT# */
};
/* Verdin PWM_3_DSI shared with GPIO1_IO1 */
pinctrl_pwm_1: pwm1grp {
fsl,pins =
<MX8MM_IOMUXC_GPIO1_IO01_PWM1_OUT 0x6>; /* SODIMM 19 */
};
pinctrl_pwm_2: pwm2grp {
fsl,pins =
<MX8MM_IOMUXC_SPDIF_RX_PWM2_OUT 0x6>; /* SODIMM 15 */
};
pinctrl_pwm_3: pwm3grp {
fsl,pins =
<MX8MM_IOMUXC_SPDIF_TX_PWM3_OUT 0x6>; /* SODIMM 16 */
};
/* Verdin PWM_3_DSI (pulled-down as active-high) shared with PWM1_OUT */
pinctrl_pwm_3_dsi_hpd_gpio: pwm3dsihpdgpiogrp {
fsl,pins =
<MX8MM_IOMUXC_GPIO1_IO01_GPIO1_IO1 0x106>; /* SODIMM 19 */
};
pinctrl_reg_eth: regethgrp {
fsl,pins =
<MX8MM_IOMUXC_SD2_WP_GPIO2_IO20 0x146>; /* PMIC_EN_ETH */
};
pinctrl_reg_usb1_en: regusb1engrp {
fsl,pins =
<MX8MM_IOMUXC_GPIO1_IO12_GPIO1_IO12 0x106>; /* SODIMM 155 */
};
pinctrl_reg_usb2_en: regusb2engrp {
fsl,pins =
<MX8MM_IOMUXC_GPIO1_IO14_GPIO1_IO14 0x106>; /* SODIMM 185 */
};
pinctrl_sai2: sai2grp {
fsl,pins =
<MX8MM_IOMUXC_SAI2_MCLK_SAI2_MCLK 0x6>, /* SODIMM 38 */
<MX8MM_IOMUXC_SAI2_TXC_SAI2_TX_BCLK 0x6>, /* SODIMM 30 */
<MX8MM_IOMUXC_SAI2_TXFS_SAI2_TX_SYNC 0x6>, /* SODIMM 32 */
<MX8MM_IOMUXC_SAI2_RXD0_SAI2_RX_DATA0 0x6>, /* SODIMM 36 */
<MX8MM_IOMUXC_SAI2_TXD0_SAI2_TX_DATA0 0x6>; /* SODIMM 34 */
};
pinctrl_sai5: sai5grp {
fsl,pins =
<MX8MM_IOMUXC_SAI5_RXD0_SAI5_RX_DATA0 0x6>, /* SODIMM 48 */
<MX8MM_IOMUXC_SAI5_RXD1_SAI5_TX_SYNC 0x6>, /* SODIMM 44 */
<MX8MM_IOMUXC_SAI5_RXD2_SAI5_TX_BCLK 0x6>, /* SODIMM 42 */
<MX8MM_IOMUXC_SAI5_RXD3_SAI5_TX_DATA0 0x6>; /* SODIMM 46 */
};
/* control signal for optional ATTPM20P or SE050 */
pinctrl_pmic_tpm_ena: pmictpmenagrp {
fsl,pins =
<MX8MM_IOMUXC_SAI1_TXD7_GPIO4_IO19 0x106>; /* PMIC_TPM_ENA */
};
pinctrl_tsp: tspgrp {
fsl,pins =
<MX8MM_IOMUXC_SAI1_RXD4_GPIO4_IO6 0x6>, /* SODIMM 148 */
<MX8MM_IOMUXC_SAI1_RXD5_GPIO4_IO7 0x6>, /* SODIMM 152 */
<MX8MM_IOMUXC_SAI1_RXD6_GPIO4_IO8 0x6>, /* SODIMM 154 */
<MX8MM_IOMUXC_SAI1_RXD7_GPIO4_IO9 0x146>, /* SODIMM 174 */
<MX8MM_IOMUXC_SAI1_TXD5_GPIO4_IO17 0x6>; /* SODIMM 150 */
};
pinctrl_uart1: uart1grp {
fsl,pins =
<MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX 0x146>, /* SODIMM 147 */
<MX8MM_IOMUXC_SAI2_RXFS_UART1_DCE_TX 0x146>; /* SODIMM 149 */
};
pinctrl_uart2: uart2grp {
fsl,pins =
<MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B 0x146>, /* SODIMM 133 */
<MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B 0x146>, /* SODIMM 135 */
<MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX 0x146>, /* SODIMM 131 */
<MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX 0x146>; /* SODIMM 129 */
};
pinctrl_uart3: uart3grp {
fsl,pins =
<MX8MM_IOMUXC_ECSPI1_MISO_UART3_DCE_CTS_B 0x146>, /* SODIMM 141 */
<MX8MM_IOMUXC_ECSPI1_MOSI_UART3_DCE_TX 0x146>, /* SODIMM 139 */
<MX8MM_IOMUXC_ECSPI1_SCLK_UART3_DCE_RX 0x146>, /* SODIMM 137 */
<MX8MM_IOMUXC_ECSPI1_SS0_UART3_DCE_RTS_B 0x146>; /* SODIMM 143 */
};
pinctrl_uart4: uart4grp {
fsl,pins =
<MX8MM_IOMUXC_UART4_RXD_UART4_DCE_RX 0x146>, /* SODIMM 151 */
<MX8MM_IOMUXC_UART4_TXD_UART4_DCE_TX 0x146>; /* SODIMM 153 */
};
pinctrl_usdhc1: usdhc1grp {
fsl,pins =
<MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x190>,
<MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d0>,
<MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d0>,
<MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d0>,
<MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d0>,
<MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d0>,
<MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4 0x1d0>,
<MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5 0x1d0>,
<MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6 0x1d0>,
<MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7 0x1d0>,
<MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0x1d1>,
<MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x190>;
};
pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
fsl,pins =
<MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x194>,
<MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d4>,
<MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d4>,
<MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d4>,
<MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d4>,
<MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d4>,
<MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4 0x1d4>,
<MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5 0x1d4>,
<MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6 0x1d4>,
<MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7 0x1d4>,
<MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0x1d1>,
<MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x194>;
};
pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
fsl,pins =
<MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x196>,
<MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d6>,
<MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d6>,
<MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d6>,
<MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d6>,
<MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d6>,
<MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4 0x1d6>,
<MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5 0x1d6>,
<MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6 0x1d6>,
<MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7 0x1d6>,
<MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0x1d1>,
<MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x196>;
};
pinctrl_usdhc2_cd: usdhc2cdgrp {
fsl,pins =
<MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x6>; /* SODIMM 84 */
};
pinctrl_usdhc2_cd_sleep: usdhc2cdslpgrp {
fsl,pins =
<MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x0>; /* SODIMM 84 */
};
pinctrl_usdhc2_pwr_en: usdhc2pwrengrp {
fsl,pins =
<MX8MM_IOMUXC_NAND_CLE_GPIO3_IO5 0x6>; /* SODIMM 76 */
};
/*
* Note: Due to ERR050080 we use discrete external on-module resistors pulling-up to the
* on-module +V3.3_1.8_SD (LDO5) rail and explicitly disable the internal pull-ups here.
*/
pinctrl_usdhc2: usdhc2grp {
fsl,pins =
<MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x10>,
<MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x90>, /* SODIMM 78 */
<MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x90>, /* SODIMM 74 */
<MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x90>, /* SODIMM 80 */
<MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x90>, /* SODIMM 82 */
<MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x90>, /* SODIMM 70 */
<MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x90>; /* SODIMM 72 */
};
pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
fsl,pins =
<MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x10>,
<MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x94>,
<MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x94>,
<MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x94>,
<MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x94>,
<MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x94>,
<MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x94>;
};
pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
fsl,pins =
<MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x10>,
<MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x96>,
<MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x96>,
<MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x96>,
<MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x96>,
<MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x96>,
<MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x96>;
};
/* Avoid backfeeding with removed card power */
pinctrl_usdhc2_sleep: usdhc2slpgrp {
fsl,pins =
<MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x0>,
<MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x0>,
<MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x0>,
<MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x0>,
<MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x0>,
<MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x0>,
<MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x0>;
};
/*
* On-module Wi-Fi/BT or type specific SDHC interface
* (e.g. on X52 extension slot of Verdin Development Board)
*/
pinctrl_usdhc3: usdhc3grp {
fsl,pins =
<MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x150>,
<MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x150>,
<MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x150>,
<MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x150>,
<MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x150>,
<MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x150>;
};
pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
fsl,pins =
<MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x154>,
<MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x154>,
<MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x154>,
<MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x154>,
<MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x154>,
<MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x154>;
};
pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
fsl,pins =
<MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x156>,
<MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x156>,
<MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x156>,
<MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x156>,
<MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x156>,
<MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x156>;
};
pinctrl_wdog: wdoggrp {
fsl,pins =
<MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0x166>; /* PMIC_WDI */
};
pinctrl_wifi_ctrl: wifictrlgrp {
fsl,pins =
<MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16 0x46>, /* WIFI_WKUP_BT */
<MX8MM_IOMUXC_SAI1_RXD7_GPIO4_IO9 0x146>, /* WIFI_W_WKUP_HOST */
<MX8MM_IOMUXC_SAI5_RXC_GPIO3_IO20 0x46>; /* WIFI_WKUP_WLAN */
};
pinctrl_wifi_i2s: bti2sgrp {
fsl,pins =
<MX8MM_IOMUXC_SAI1_RXD4_SAI6_TX_BCLK 0x6>, /* WIFI_TX_BCLK */
<MX8MM_IOMUXC_SAI1_RXD5_SAI6_TX_DATA0 0x6>, /* WIFI_TX_DATA0 */
<MX8MM_IOMUXC_SAI1_RXD6_SAI6_TX_SYNC 0x6>, /* WIFI_TX_SYNC */
<MX8MM_IOMUXC_SAI1_TXD5_SAI6_RX_DATA0 0x6>; /* WIFI_RX_DATA0 */
};
pinctrl_wifi_pwr_en: wifipwrengrp {
fsl,pins =
<MX8MM_IOMUXC_SAI5_MCLK_GPIO3_IO25 0x6>; /* PMIC_EN_WIFI */
};
};