| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * Copyright (c) 2018-2019, The Linux Foundation. All rights reserved. |
| */ |
| |
| #include <linux/clk-provider.h> |
| #include <linux/err.h> |
| #include <linux/kernel.h> |
| #include <linux/module.h> |
| #include <linux/of.h> |
| #include <linux/of_device.h> |
| #include <linux/platform_device.h> |
| #include <soc/qcom/cmd-db.h> |
| #include <soc/qcom/rpmh.h> |
| #include <soc/qcom/tcs.h> |
| |
| #include <dt-bindings/clock/qcom,rpmh.h> |
| |
| #define CLK_RPMH_ARC_EN_OFFSET 0 |
| #define CLK_RPMH_VRM_EN_OFFSET 4 |
| |
| /** |
| * struct bcm_db - Auxiliary data pertaining to each Bus Clock Manager(BCM) |
| * @unit: divisor used to convert Hz value to an RPMh msg |
| * @width: multiplier used to convert Hz value to an RPMh msg |
| * @vcd: virtual clock domain that this bcm belongs to |
| * @reserved: reserved to pad the struct |
| */ |
| struct bcm_db { |
| __le32 unit; |
| __le16 width; |
| u8 vcd; |
| u8 reserved; |
| }; |
| |
| /** |
| * struct clk_rpmh - individual rpmh clock data structure |
| * @hw: handle between common and hardware-specific interfaces |
| * @res_name: resource name for the rpmh clock |
| * @div: clock divider to compute the clock rate |
| * @res_addr: base address of the rpmh resource within the RPMh |
| * @res_on_val: rpmh clock enable value |
| * @state: rpmh clock requested state |
| * @aggr_state: rpmh clock aggregated state |
| * @last_sent_aggr_state: rpmh clock last aggr state sent to RPMh |
| * @valid_state_mask: mask to determine the state of the rpmh clock |
| * @unit: divisor to convert rate to rpmh msg in magnitudes of Khz |
| * @dev: device to which it is attached |
| * @peer: pointer to the clock rpmh sibling |
| */ |
| struct clk_rpmh { |
| struct clk_hw hw; |
| const char *res_name; |
| u8 div; |
| u32 res_addr; |
| u32 res_on_val; |
| u32 state; |
| u32 aggr_state; |
| u32 last_sent_aggr_state; |
| u32 valid_state_mask; |
| u32 unit; |
| struct device *dev; |
| struct clk_rpmh *peer; |
| }; |
| |
| struct clk_rpmh_desc { |
| struct clk_hw **clks; |
| size_t num_clks; |
| }; |
| |
| static DEFINE_MUTEX(rpmh_clk_lock); |
| |
| #define __DEFINE_CLK_RPMH(_platform, _name, _name_active, _res_name, \ |
| _res_en_offset, _res_on, _div) \ |
| static struct clk_rpmh _platform##_##_name_active; \ |
| static struct clk_rpmh _platform##_##_name = { \ |
| .res_name = _res_name, \ |
| .res_addr = _res_en_offset, \ |
| .res_on_val = _res_on, \ |
| .div = _div, \ |
| .peer = &_platform##_##_name_active, \ |
| .valid_state_mask = (BIT(RPMH_WAKE_ONLY_STATE) | \ |
| BIT(RPMH_ACTIVE_ONLY_STATE) | \ |
| BIT(RPMH_SLEEP_STATE)), \ |
| .hw.init = &(struct clk_init_data){ \ |
| .ops = &clk_rpmh_ops, \ |
| .name = #_name, \ |
| .parent_data = &(const struct clk_parent_data){ \ |
| .fw_name = "xo", \ |
| .name = "xo_board", \ |
| }, \ |
| .num_parents = 1, \ |
| }, \ |
| }; \ |
| static struct clk_rpmh _platform##_##_name_active = { \ |
| .res_name = _res_name, \ |
| .res_addr = _res_en_offset, \ |
| .res_on_val = _res_on, \ |
| .div = _div, \ |
| .peer = &_platform##_##_name, \ |
| .valid_state_mask = (BIT(RPMH_WAKE_ONLY_STATE) | \ |
| BIT(RPMH_ACTIVE_ONLY_STATE)), \ |
| .hw.init = &(struct clk_init_data){ \ |
| .ops = &clk_rpmh_ops, \ |
| .name = #_name_active, \ |
| .parent_data = &(const struct clk_parent_data){ \ |
| .fw_name = "xo", \ |
| .name = "xo_board", \ |
| }, \ |
| .num_parents = 1, \ |
| }, \ |
| } |
| |
| #define DEFINE_CLK_RPMH_ARC(_platform, _name, _name_active, _res_name, \ |
| _res_on, _div) \ |
| __DEFINE_CLK_RPMH(_platform, _name, _name_active, _res_name, \ |
| CLK_RPMH_ARC_EN_OFFSET, _res_on, _div) |
| |
| #define DEFINE_CLK_RPMH_VRM(_platform, _name, _name_active, _res_name, \ |
| _div) \ |
| __DEFINE_CLK_RPMH(_platform, _name, _name_active, _res_name, \ |
| CLK_RPMH_VRM_EN_OFFSET, 1, _div) |
| |
| #define DEFINE_CLK_RPMH_BCM(_platform, _name, _res_name) \ |
| static struct clk_rpmh _platform##_##_name = { \ |
| .res_name = _res_name, \ |
| .valid_state_mask = BIT(RPMH_ACTIVE_ONLY_STATE), \ |
| .div = 1, \ |
| .hw.init = &(struct clk_init_data){ \ |
| .ops = &clk_rpmh_bcm_ops, \ |
| .name = #_name, \ |
| }, \ |
| } |
| |
| static inline struct clk_rpmh *to_clk_rpmh(struct clk_hw *_hw) |
| { |
| return container_of(_hw, struct clk_rpmh, hw); |
| } |
| |
| static inline bool has_state_changed(struct clk_rpmh *c, u32 state) |
| { |
| return (c->last_sent_aggr_state & BIT(state)) |
| != (c->aggr_state & BIT(state)); |
| } |
| |
| static int clk_rpmh_send_aggregate_command(struct clk_rpmh *c) |
| { |
| struct tcs_cmd cmd = { 0 }; |
| u32 cmd_state, on_val; |
| enum rpmh_state state = RPMH_SLEEP_STATE; |
| int ret; |
| |
| cmd.addr = c->res_addr; |
| cmd_state = c->aggr_state; |
| on_val = c->res_on_val; |
| |
| for (; state <= RPMH_ACTIVE_ONLY_STATE; state++) { |
| if (has_state_changed(c, state)) { |
| if (cmd_state & BIT(state)) |
| cmd.data = on_val; |
| |
| ret = rpmh_write_async(c->dev, state, &cmd, 1); |
| if (ret) { |
| dev_err(c->dev, "set %s state of %s failed: (%d)\n", |
| !state ? "sleep" : |
| state == RPMH_WAKE_ONLY_STATE ? |
| "wake" : "active", c->res_name, ret); |
| return ret; |
| } |
| } |
| } |
| |
| c->last_sent_aggr_state = c->aggr_state; |
| c->peer->last_sent_aggr_state = c->last_sent_aggr_state; |
| |
| return 0; |
| } |
| |
| /* |
| * Update state and aggregate state values based on enable value. |
| */ |
| static int clk_rpmh_aggregate_state_send_command(struct clk_rpmh *c, |
| bool enable) |
| { |
| int ret; |
| |
| /* Nothing required to be done if already off or on */ |
| if (enable == c->state) |
| return 0; |
| |
| c->state = enable ? c->valid_state_mask : 0; |
| c->aggr_state = c->state | c->peer->state; |
| c->peer->aggr_state = c->aggr_state; |
| |
| ret = clk_rpmh_send_aggregate_command(c); |
| if (!ret) |
| return 0; |
| |
| if (ret && enable) |
| c->state = 0; |
| else if (ret) |
| c->state = c->valid_state_mask; |
| |
| WARN(1, "clk: %s failed to %s\n", c->res_name, |
| enable ? "enable" : "disable"); |
| return ret; |
| } |
| |
| static int clk_rpmh_prepare(struct clk_hw *hw) |
| { |
| struct clk_rpmh *c = to_clk_rpmh(hw); |
| int ret = 0; |
| |
| mutex_lock(&rpmh_clk_lock); |
| ret = clk_rpmh_aggregate_state_send_command(c, true); |
| mutex_unlock(&rpmh_clk_lock); |
| |
| return ret; |
| }; |
| |
| static void clk_rpmh_unprepare(struct clk_hw *hw) |
| { |
| struct clk_rpmh *c = to_clk_rpmh(hw); |
| |
| mutex_lock(&rpmh_clk_lock); |
| clk_rpmh_aggregate_state_send_command(c, false); |
| mutex_unlock(&rpmh_clk_lock); |
| }; |
| |
| static unsigned long clk_rpmh_recalc_rate(struct clk_hw *hw, |
| unsigned long prate) |
| { |
| struct clk_rpmh *r = to_clk_rpmh(hw); |
| |
| /* |
| * RPMh clocks have a fixed rate. Return static rate. |
| */ |
| return prate / r->div; |
| } |
| |
| static const struct clk_ops clk_rpmh_ops = { |
| .prepare = clk_rpmh_prepare, |
| .unprepare = clk_rpmh_unprepare, |
| .recalc_rate = clk_rpmh_recalc_rate, |
| }; |
| |
| static int clk_rpmh_bcm_send_cmd(struct clk_rpmh *c, bool enable) |
| { |
| struct tcs_cmd cmd = { 0 }; |
| u32 cmd_state; |
| int ret; |
| |
| mutex_lock(&rpmh_clk_lock); |
| |
| cmd_state = 0; |
| if (enable) { |
| cmd_state = 1; |
| if (c->aggr_state) |
| cmd_state = c->aggr_state; |
| } |
| |
| if (c->last_sent_aggr_state == cmd_state) { |
| mutex_unlock(&rpmh_clk_lock); |
| return 0; |
| } |
| |
| cmd.addr = c->res_addr; |
| cmd.data = BCM_TCS_CMD(1, enable, 0, cmd_state); |
| |
| ret = rpmh_write_async(c->dev, RPMH_ACTIVE_ONLY_STATE, &cmd, 1); |
| if (ret) { |
| dev_err(c->dev, "set active state of %s failed: (%d)\n", |
| c->res_name, ret); |
| mutex_unlock(&rpmh_clk_lock); |
| return ret; |
| } |
| |
| c->last_sent_aggr_state = cmd_state; |
| |
| mutex_unlock(&rpmh_clk_lock); |
| |
| return 0; |
| } |
| |
| static int clk_rpmh_bcm_prepare(struct clk_hw *hw) |
| { |
| struct clk_rpmh *c = to_clk_rpmh(hw); |
| |
| return clk_rpmh_bcm_send_cmd(c, true); |
| }; |
| |
| static void clk_rpmh_bcm_unprepare(struct clk_hw *hw) |
| { |
| struct clk_rpmh *c = to_clk_rpmh(hw); |
| |
| clk_rpmh_bcm_send_cmd(c, false); |
| }; |
| |
| static int clk_rpmh_bcm_set_rate(struct clk_hw *hw, unsigned long rate, |
| unsigned long parent_rate) |
| { |
| struct clk_rpmh *c = to_clk_rpmh(hw); |
| |
| c->aggr_state = rate / c->unit; |
| /* |
| * Since any non-zero value sent to hw would result in enabling the |
| * clock, only send the value if the clock has already been prepared. |
| */ |
| if (clk_hw_is_prepared(hw)) |
| clk_rpmh_bcm_send_cmd(c, true); |
| |
| return 0; |
| }; |
| |
| static long clk_rpmh_round_rate(struct clk_hw *hw, unsigned long rate, |
| unsigned long *parent_rate) |
| { |
| return rate; |
| } |
| |
| static unsigned long clk_rpmh_bcm_recalc_rate(struct clk_hw *hw, |
| unsigned long prate) |
| { |
| struct clk_rpmh *c = to_clk_rpmh(hw); |
| |
| return c->aggr_state * c->unit; |
| } |
| |
| static const struct clk_ops clk_rpmh_bcm_ops = { |
| .prepare = clk_rpmh_bcm_prepare, |
| .unprepare = clk_rpmh_bcm_unprepare, |
| .set_rate = clk_rpmh_bcm_set_rate, |
| .round_rate = clk_rpmh_round_rate, |
| .recalc_rate = clk_rpmh_bcm_recalc_rate, |
| }; |
| |
| /* Resource name must match resource id present in cmd-db. */ |
| DEFINE_CLK_RPMH_ARC(sdm845, bi_tcxo, bi_tcxo_ao, "xo.lvl", 0x3, 2); |
| DEFINE_CLK_RPMH_VRM(sdm845, ln_bb_clk2, ln_bb_clk2_ao, "lnbclka2", 2); |
| DEFINE_CLK_RPMH_VRM(sdm845, ln_bb_clk3, ln_bb_clk3_ao, "lnbclka3", 2); |
| DEFINE_CLK_RPMH_VRM(sdm845, rf_clk1, rf_clk1_ao, "rfclka1", 1); |
| DEFINE_CLK_RPMH_VRM(sdm845, rf_clk2, rf_clk2_ao, "rfclka2", 1); |
| DEFINE_CLK_RPMH_VRM(sdm845, rf_clk3, rf_clk3_ao, "rfclka3", 1); |
| DEFINE_CLK_RPMH_BCM(sdm845, ipa, "IP0"); |
| |
| static struct clk_hw *sdm845_rpmh_clocks[] = { |
| [RPMH_CXO_CLK] = &sdm845_bi_tcxo.hw, |
| [RPMH_CXO_CLK_A] = &sdm845_bi_tcxo_ao.hw, |
| [RPMH_LN_BB_CLK2] = &sdm845_ln_bb_clk2.hw, |
| [RPMH_LN_BB_CLK2_A] = &sdm845_ln_bb_clk2_ao.hw, |
| [RPMH_LN_BB_CLK3] = &sdm845_ln_bb_clk3.hw, |
| [RPMH_LN_BB_CLK3_A] = &sdm845_ln_bb_clk3_ao.hw, |
| [RPMH_RF_CLK1] = &sdm845_rf_clk1.hw, |
| [RPMH_RF_CLK1_A] = &sdm845_rf_clk1_ao.hw, |
| [RPMH_RF_CLK2] = &sdm845_rf_clk2.hw, |
| [RPMH_RF_CLK2_A] = &sdm845_rf_clk2_ao.hw, |
| [RPMH_RF_CLK3] = &sdm845_rf_clk3.hw, |
| [RPMH_RF_CLK3_A] = &sdm845_rf_clk3_ao.hw, |
| [RPMH_IPA_CLK] = &sdm845_ipa.hw, |
| }; |
| |
| static const struct clk_rpmh_desc clk_rpmh_sdm845 = { |
| .clks = sdm845_rpmh_clocks, |
| .num_clks = ARRAY_SIZE(sdm845_rpmh_clocks), |
| }; |
| |
| DEFINE_CLK_RPMH_ARC(sm8150, bi_tcxo, bi_tcxo_ao, "xo.lvl", 0x3, 2); |
| DEFINE_CLK_RPMH_VRM(sm8150, ln_bb_clk2, ln_bb_clk2_ao, "lnbclka2", 2); |
| DEFINE_CLK_RPMH_VRM(sm8150, ln_bb_clk3, ln_bb_clk3_ao, "lnbclka3", 2); |
| DEFINE_CLK_RPMH_VRM(sm8150, rf_clk1, rf_clk1_ao, "rfclka1", 1); |
| DEFINE_CLK_RPMH_VRM(sm8150, rf_clk2, rf_clk2_ao, "rfclka2", 1); |
| DEFINE_CLK_RPMH_VRM(sm8150, rf_clk3, rf_clk3_ao, "rfclka3", 1); |
| |
| static struct clk_hw *sm8150_rpmh_clocks[] = { |
| [RPMH_CXO_CLK] = &sm8150_bi_tcxo.hw, |
| [RPMH_CXO_CLK_A] = &sm8150_bi_tcxo_ao.hw, |
| [RPMH_LN_BB_CLK2] = &sm8150_ln_bb_clk2.hw, |
| [RPMH_LN_BB_CLK2_A] = &sm8150_ln_bb_clk2_ao.hw, |
| [RPMH_LN_BB_CLK3] = &sm8150_ln_bb_clk3.hw, |
| [RPMH_LN_BB_CLK3_A] = &sm8150_ln_bb_clk3_ao.hw, |
| [RPMH_RF_CLK1] = &sm8150_rf_clk1.hw, |
| [RPMH_RF_CLK1_A] = &sm8150_rf_clk1_ao.hw, |
| [RPMH_RF_CLK2] = &sm8150_rf_clk2.hw, |
| [RPMH_RF_CLK2_A] = &sm8150_rf_clk2_ao.hw, |
| [RPMH_RF_CLK3] = &sm8150_rf_clk3.hw, |
| [RPMH_RF_CLK3_A] = &sm8150_rf_clk3_ao.hw, |
| }; |
| |
| static const struct clk_rpmh_desc clk_rpmh_sm8150 = { |
| .clks = sm8150_rpmh_clocks, |
| .num_clks = ARRAY_SIZE(sm8150_rpmh_clocks), |
| }; |
| |
| static struct clk_hw *of_clk_rpmh_hw_get(struct of_phandle_args *clkspec, |
| void *data) |
| { |
| struct clk_rpmh_desc *rpmh = data; |
| unsigned int idx = clkspec->args[0]; |
| |
| if (idx >= rpmh->num_clks) { |
| pr_err("%s: invalid index %u\n", __func__, idx); |
| return ERR_PTR(-EINVAL); |
| } |
| |
| return rpmh->clks[idx]; |
| } |
| |
| static int clk_rpmh_probe(struct platform_device *pdev) |
| { |
| struct clk_hw **hw_clks; |
| struct clk_rpmh *rpmh_clk; |
| const struct clk_rpmh_desc *desc; |
| int ret, i; |
| |
| desc = of_device_get_match_data(&pdev->dev); |
| if (!desc) |
| return -ENODEV; |
| |
| hw_clks = desc->clks; |
| |
| for (i = 0; i < desc->num_clks; i++) { |
| const char *name = hw_clks[i]->init->name; |
| u32 res_addr; |
| size_t aux_data_len; |
| const struct bcm_db *data; |
| |
| rpmh_clk = to_clk_rpmh(hw_clks[i]); |
| res_addr = cmd_db_read_addr(rpmh_clk->res_name); |
| if (!res_addr) { |
| dev_err(&pdev->dev, "missing RPMh resource address for %s\n", |
| rpmh_clk->res_name); |
| return -ENODEV; |
| } |
| |
| data = cmd_db_read_aux_data(rpmh_clk->res_name, &aux_data_len); |
| if (IS_ERR(data)) { |
| ret = PTR_ERR(data); |
| dev_err(&pdev->dev, |
| "error reading RPMh aux data for %s (%d)\n", |
| rpmh_clk->res_name, ret); |
| return ret; |
| } |
| |
| /* Convert unit from Khz to Hz */ |
| if (aux_data_len == sizeof(*data)) |
| rpmh_clk->unit = le32_to_cpu(data->unit) * 1000ULL; |
| |
| rpmh_clk->res_addr += res_addr; |
| rpmh_clk->dev = &pdev->dev; |
| |
| ret = devm_clk_hw_register(&pdev->dev, hw_clks[i]); |
| if (ret) { |
| dev_err(&pdev->dev, "failed to register %s\n", name); |
| return ret; |
| } |
| } |
| |
| /* typecast to silence compiler warning */ |
| ret = devm_of_clk_add_hw_provider(&pdev->dev, of_clk_rpmh_hw_get, |
| (void *)desc); |
| if (ret) { |
| dev_err(&pdev->dev, "Failed to add clock provider\n"); |
| return ret; |
| } |
| |
| dev_dbg(&pdev->dev, "Registered RPMh clocks\n"); |
| |
| return 0; |
| } |
| |
| static const struct of_device_id clk_rpmh_match_table[] = { |
| { .compatible = "qcom,sdm845-rpmh-clk", .data = &clk_rpmh_sdm845}, |
| { .compatible = "qcom,sm8150-rpmh-clk", .data = &clk_rpmh_sm8150}, |
| { } |
| }; |
| MODULE_DEVICE_TABLE(of, clk_rpmh_match_table); |
| |
| static struct platform_driver clk_rpmh_driver = { |
| .probe = clk_rpmh_probe, |
| .driver = { |
| .name = "clk-rpmh", |
| .of_match_table = clk_rpmh_match_table, |
| }, |
| }; |
| |
| static int __init clk_rpmh_init(void) |
| { |
| return platform_driver_register(&clk_rpmh_driver); |
| } |
| subsys_initcall(clk_rpmh_init); |
| |
| static void __exit clk_rpmh_exit(void) |
| { |
| platform_driver_unregister(&clk_rpmh_driver); |
| } |
| module_exit(clk_rpmh_exit); |
| |
| MODULE_DESCRIPTION("QCOM RPMh Clock Driver"); |
| MODULE_LICENSE("GPL v2"); |