arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi - linux - Git at Google

 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
 /*
  * Google Gru (and derivatives) board device tree source
  *
  * Copyright 2016-2017 Google, Inc
  */

 #include <dt-bindings/input/input.h>
 #include "rk3399.dtsi"
 #include "rk3399-op1-opp.dtsi"

 / {
 	chosen {
 		stdout-path = "serial2:115200n8";
 	};

 	/*
 	 * Power Tree
 	 *
 	 * In general an attempt is made to include all rails called out by
 	 * the schematic as long as those rails interact in some way with
 	 * the AP.  AKA:
 	 * - Rails that only connect to the EC (or devices that the EC talks to)
 	 *   are not included.
 	 * - Rails _are_ included if the rails go to the AP even if the AP
 	 *   doesn't currently care about them / they are always on.  The idea
 	 *   here is that it makes it easier to map to the schematic or extend
 	 *   later.
 	 *
 	 * If two rails are substantially the same from the AP's point of
 	 * view, though, we won't create a full fixed regulator.  We'll just
 	 * put the child rail as an alias of the parent rail.  Sometimes rails
 	 * look the same to the AP because one of these is true:
 	 * - The EC controls the enable and the EC always enables a rail as
 	 *   long as the AP is running.
 	 * - The rails are actually connected to each other by a jumper and
 	 *   the distinction is just there to add clarity/flexibility to the
 	 *   schematic.
 	 */

 	ppvar_sys: ppvar-sys {
 		compatible = "regulator-fixed";
 		regulator-name = "ppvar_sys";
 		regulator-always-on;
 		regulator-boot-on;
 	};

 	pp1200_lpddr: pp1200-lpddr {
 		compatible = "regulator-fixed";
 		regulator-name = "pp1200_lpddr";

 		/* EC turns on w/ lpddr_pwr_en; always on for AP */
 		regulator-always-on;
 		regulator-boot-on;
 		regulator-min-microvolt = <1200000>;
 		regulator-max-microvolt = <1200000>;

 		vin-supply = <&ppvar_sys>;
 	};

 	pp1800: pp1800 {
 		compatible = "regulator-fixed";
 		regulator-name = "pp1800";

 		/* Always on when ppvar_sys shows power good */
 		regulator-always-on;
 		regulator-boot-on;
 		regulator-min-microvolt = <1800000>;
 		regulator-max-microvolt = <1800000>;

 		vin-supply = <&ppvar_sys>;
 	};

 	pp3300: pp3300 {
 		compatible = "regulator-fixed";
 		regulator-name = "pp3300";

 		/* Always on; plain and simple */
 		regulator-always-on;
 		regulator-boot-on;
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;

 		vin-supply = <&ppvar_sys>;
 	};

 	pp5000: pp5000 {
 		compatible = "regulator-fixed";
 		regulator-name = "pp5000";

 		/* EC turns on w/ pp5000_en; always on for AP */
 		regulator-always-on;
 		regulator-boot-on;
 		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;

 		vin-supply = <&ppvar_sys>;
 	};

 	ppvar_bigcpu_pwm: ppvar-bigcpu-pwm {
 		compatible = "pwm-regulator";
 		regulator-name = "ppvar_bigcpu_pwm";

 		pwms = <&pwm1 0 3337 0>;
 		pwm-supply = <&ppvar_sys>;
 		pwm-dutycycle-range = <100 0>;
 		pwm-dutycycle-unit = <100>;

 		/* EC turns on w/ ap_core_en; always on for AP */
 		regulator-always-on;
 		regulator-boot-on;
 		regulator-min-microvolt = <800107>;
 		regulator-max-microvolt = <1302232>;
 	};

 	ppvar_bigcpu: ppvar-bigcpu {
 		compatible = "vctrl-regulator";
 		regulator-name = "ppvar_bigcpu";

 		regulator-min-microvolt = <800107>;
 		regulator-max-microvolt = <1302232>;

 		ctrl-supply = <&ppvar_bigcpu_pwm>;
 		ctrl-voltage-range = <800107 1302232>;

 		regulator-settling-time-up-us = <322>;
 	};

 	ppvar_litcpu_pwm: ppvar-litcpu-pwm {
 		compatible = "pwm-regulator";
 		regulator-name = "ppvar_litcpu_pwm";

 		pwms = <&pwm2 0 3337 0>;
 		pwm-supply = <&ppvar_sys>;
 		pwm-dutycycle-range = <100 0>;
 		pwm-dutycycle-unit = <100>;

 		/* EC turns on w/ ap_core_en; always on for AP */
 		regulator-always-on;
 		regulator-boot-on;
 		regulator-min-microvolt = <797743>;
 		regulator-max-microvolt = <1307837>;
 	};

 	ppvar_litcpu: ppvar-litcpu {
 		compatible = "vctrl-regulator";
 		regulator-name = "ppvar_litcpu";

 		regulator-min-microvolt = <797743>;
 		regulator-max-microvolt = <1307837>;

 		ctrl-supply = <&ppvar_litcpu_pwm>;
 		ctrl-voltage-range = <797743 1307837>;

 		regulator-settling-time-up-us = <384>;
 	};

 	ppvar_gpu_pwm: ppvar-gpu-pwm {
 		compatible = "pwm-regulator";
 		regulator-name = "ppvar_gpu_pwm";

 		pwms = <&pwm0 0 3337 0>;
 		pwm-supply = <&ppvar_sys>;
 		pwm-dutycycle-range = <100 0>;
 		pwm-dutycycle-unit = <100>;

 		/* EC turns on w/ ap_core_en; always on for AP */
 		regulator-always-on;
 		regulator-boot-on;
 		regulator-min-microvolt = <786384>;
 		regulator-max-microvolt = <1217747>;
 	};

 	ppvar_gpu: ppvar-gpu {
 		compatible = "vctrl-regulator";
 		regulator-name = "ppvar_gpu";

 		regulator-min-microvolt = <786384>;
 		regulator-max-microvolt = <1217747>;

 		ctrl-supply = <&ppvar_gpu_pwm>;
 		ctrl-voltage-range = <786384 1217747>;

 		regulator-settling-time-up-us = <390>;
 	};

 	/* EC turns on w/ pp900_ddrpll_en */
 	pp900_ddrpll: pp900-ap {
 	};

 	/* EC turns on w/ pp900_pll_en */
 	pp900_pll: pp900-ap {
 	};

 	/* EC turns on w/ pp900_pmu_en */
 	pp900_pmu: pp900-ap {
 	};

 	/* EC turns on w/ pp1800_s0_en_l */
 	pp1800_ap_io: pp1800_emmc: pp1800_nfc: pp1800_s0: pp1800 {
 	};

 	/* EC turns on w/ pp1800_avdd_en_l */
 	pp1800_avdd: pp1800 {
 	};

 	/* EC turns on w/ pp1800_lid_en_l */
 	pp1800_lid: pp1800_mic: pp1800 {
 	};

 	/* EC turns on w/ lpddr_pwr_en */
 	pp1800_lpddr: pp1800 {
 	};

 	/* EC turns on w/ pp1800_pmu_en_l */
 	pp1800_pmu: pp1800 {
 	};

 	/* EC turns on w/ pp1800_usb_en_l */
 	pp1800_usb: pp1800 {
 	};

 	pp3000_sd_slot: pp3000-sd-slot {
 		compatible = "regulator-fixed";
 		regulator-name = "pp3000_sd_slot";
 		pinctrl-names = "default";
 		pinctrl-0 = <&sd_slot_pwr_en>;

 		enable-active-high;
 		gpio = <&gpio4 29 GPIO_ACTIVE_HIGH>;

 		vin-supply = <&pp3000>;
 	};

 	/*
 	 * Technically, this is a small abuse of 'regulator-gpio'; this
 	 * regulator is a mux between pp1800 and pp3300. pp1800 and pp3300 are
 	 * always on though, so it is sufficient to simply control the mux
 	 * here.
 	 */
 	ppvar_sd_card_io: ppvar-sd-card-io {
 		compatible = "regulator-gpio";
 		regulator-name = "ppvar_sd_card_io";
 		pinctrl-names = "default";
 		pinctrl-0 = <&sd_io_pwr_en &sd_pwr_1800_sel>;

 		enable-active-high;
 		enable-gpio = <&gpio2 2 GPIO_ACTIVE_HIGH>;
 		gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>;
 		states = <1800000 0x1
 			  3000000 0x0>;

 		regulator-min-microvolt = <1800000>;
 		regulator-max-microvolt = <3000000>;
 	};

 	/* EC turns on w/ pp3300_trackpad_en_l */
 	pp3300_trackpad: pp3300-trackpad {
 	};

 	/* EC turns on w/ usb_a_en */
 	pp5000_usb_a_vbus: pp5000 {
 	};

 	ap_rtc_clk: ap-rtc-clk {
 		compatible = "fixed-clock";
 		clock-frequency = <32768>;
 		clock-output-names = "xin32k";
 		#clock-cells = <0>;
 	};

 	max98357a: max98357a {
 		compatible = "maxim,max98357a";
 		pinctrl-names = "default";
 		pinctrl-0 = <&sdmode_en>;
 		sdmode-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
 		sdmode-delay = <2>;
 		#sound-dai-cells = <0>;
 		status = "okay";
 	};

 	sound: sound {
 		compatible = "rockchip,rk3399-gru-sound";
 		rockchip,cpu = <&i2s0 &i2s2>;
 	};
 };

 &cdn_dp {
 	status = "okay";
 };

 /*
  * Set some suspend operating points to avoid OVP in suspend
  *
  * When we go into S3 ARM Trusted Firmware will transition our PWM regulators
  * from wherever they're at back to the "default" operating point (whatever
  * voltage we get when we set the PWM pins to "input").
  *
  * This quick transition under light load has the possibility to trigger the
  * regulator "over voltage protection" (OVP).
  *
  * To make extra certain that we don't hit this OVP at suspend time, we'll
  * transition to a voltage that's much closer to the default (~1.0 V) so that
  * there will not be a big jump.  Technically we only need to get within 200 mV
  * of the default voltage, but the speed here should be fast enough and we need
  * suspend/resume to be rock solid.
  */

 &cluster0_opp {
 	opp05 {
 		opp-suspend;
 	};
 };

 &cluster1_opp {
 	opp06 {
 		opp-suspend;
 	};
 };

 &cpu_l0 {
 	cpu-supply = <&ppvar_litcpu>;
 };

 &cpu_l1 {
 	cpu-supply = <&ppvar_litcpu>;
 };

 &cpu_l2 {
 	cpu-supply = <&ppvar_litcpu>;
 };

 &cpu_l3 {
 	cpu-supply = <&ppvar_litcpu>;
 };

 &cpu_b0 {
 	cpu-supply = <&ppvar_bigcpu>;
 };

 &cpu_b1 {
 	cpu-supply = <&ppvar_bigcpu>;
 };


 &cru {
 	assigned-clocks =
 		<&cru PLL_GPLL>, <&cru PLL_CPLL>,
 		<&cru PLL_NPLL>,
 		<&cru ACLK_PERIHP>, <&cru HCLK_PERIHP>,
 		<&cru PCLK_PERIHP>,
 		<&cru ACLK_PERILP0>, <&cru HCLK_PERILP0>,
 		<&cru PCLK_PERILP0>, <&cru ACLK_CCI>,
 		<&cru HCLK_PERILP1>, <&cru PCLK_PERILP1>,
 		<&cru ACLK_VIO>, <&cru ACLK_HDCP>,
 		<&cru ACLK_GIC_PRE>,
 		<&cru PCLK_DDR>;
 	assigned-clock-rates =
 		<600000000>, <800000000>,
 		<1000000000>,
 		<150000000>, <75000000>,
 		<37500000>,
 		<100000000>, <100000000>,
 		<50000000>, <800000000>,
 		<100000000>, <50000000>,
 		<400000000>, <400000000>,
 		<200000000>,
 		<200000000>;
 };

 &emmc_phy {
 	status = "okay";
 };

 &gpu {
 	mali-supply = <&ppvar_gpu>;
 	status = "okay";
 };

 ap_i2c_ts: &i2c3 {
 	status = "okay";

 	clock-frequency = <400000>;

 	/* These are relatively safe rise/fall times */
 	i2c-scl-falling-time-ns = <50>;
 	i2c-scl-rising-time-ns = <300>;
 };

 ap_i2c_audio: &i2c8 {
 	status = "okay";

 	clock-frequency = <400000>;

 	/* These are relatively safe rise/fall times */
 	i2c-scl-falling-time-ns = <50>;
 	i2c-scl-rising-time-ns = <300>;

 	codec: da7219@1a {
 		compatible = "dlg,da7219";
 		reg = <0x1a>;
 		interrupt-parent = <&gpio1>;
 		interrupts = <23 IRQ_TYPE_LEVEL_LOW>;
 		clocks = <&cru SCLK_I2S_8CH_OUT>;
 		clock-names = "mclk";
 		dlg,micbias-lvl = <2600>;
 		dlg,mic-amp-in-sel = "diff";
 		pinctrl-names = "default";
 		pinctrl-0 = <&headset_int_l>;
 		VDD-supply = <&pp1800>;
 		VDDMIC-supply = <&pp3300>;
 		VDDIO-supply = <&pp1800>;

 		da7219_aad {
 			dlg,adc-1bit-rpt = <1>;
 			dlg,btn-avg = <4>;
 			dlg,btn-cfg = <50>;
 			dlg,mic-det-thr = <500>;
 			dlg,jack-ins-deb = <20>;
 			dlg,jack-det-rate = "32ms_64ms";
 			dlg,jack-rem-deb = <1>;

 			dlg,a-d-btn-thr = <0xa>;
 			dlg,d-b-btn-thr = <0x16>;
 			dlg,b-c-btn-thr = <0x21>;
 			dlg,c-mic-btn-thr = <0x3E>;
 		};
 	};
 };

 &i2s0 {
 	status = "okay";
 };

 &i2s2 {
 	status = "okay";
 };

 &io_domains {
 	status = "okay";

 	audio-supply = <&pp1800_audio>;		/* APIO5_VDD;  3d 4a */
 	bt656-supply = <&pp1800_ap_io>;		/* APIO2_VDD;  2a 2b */
 	gpio1830-supply = <&pp3000_ap>;		/* APIO4_VDD;  4c 4d */
 	sdmmc-supply = <&ppvar_sd_card_io>;	/* SDMMC0_VDD; 4b    */
 };

 &pcie0 {
 	status = "okay";

 	ep-gpios = <&gpio2 27 GPIO_ACTIVE_HIGH>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pcie_clkreqn_cpm>, <&wifi_perst_l>;
 	vpcie3v3-supply = <&pp3300_wifi_bt>;
 	vpcie1v8-supply = <&wlan_pd_n>; /* HACK: see &wlan_pd_n */
 	vpcie0v9-supply = <&pp900_pcie>;

 	pci_rootport: pcie@0,0 {
 		reg = <0x83000000 0x0 0x00000000 0x0 0x00000000>;
 		#address-cells = <3>;
 		#size-cells = <2>;
 		ranges;
 	};
 };

 &pcie_phy {
 	status = "okay";
 };

 &pmu_io_domains {
 	status = "okay";

 	pmu1830-supply = <&pp1800_pmu>;		/* PMUIO2_VDD */
 };

 &pwm0 {
 	status = "okay";
 };

 &pwm1 {
 	status = "okay";
 };

 &pwm2 {
 	status = "okay";
 };

 &pwm3 {
 	status = "okay";
 };

 &sdhci {
 	/*
 	 * Signal integrity isn't great at 200 MHz and 150 MHz (DDR) gives the
 	 * same (or nearly the same) performance for all eMMC that are intended
 	 * to be used.
 	 */
 	assigned-clock-rates = <150000000>;

 	bus-width = <8>;
 	mmc-hs400-1_8v;
 	mmc-hs400-enhanced-strobe;
 	non-removable;
 	status = "okay";
 };

 &sdmmc {
 	status = "okay";

 	/*
 	 * Note: configure "sdmmc_cd" as card detect even though it's actually
 	 * hooked to ground.  Because we specified "cd-gpios" below dw_mmc
 	 * should be ignoring card detect anyway.  Specifying the pin as
 	 * sdmmc_cd means that even if you've got GRF_SOC_CON7[12] (force_jtag)
 	 * turned on that the system will still make sure the port is
 	 * configured as SDMMC and not JTAG.
 	 */
 	pinctrl-names = "default";
 	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_cd_gpio
 		     &sdmmc_bus4>;

 	bus-width = <4>;
 	cap-mmc-highspeed;
 	cap-sd-highspeed;
 	cd-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>;
 	disable-wp;
 	sd-uhs-sdr12;
 	sd-uhs-sdr25;
 	sd-uhs-sdr50;
 	sd-uhs-sdr104;
 	vmmc-supply = <&pp3000_sd_slot>;
 	vqmmc-supply = <&ppvar_sd_card_io>;
 };

 &spi1 {
 	status = "okay";

 	pinctrl-names = "default", "sleep";
 	pinctrl-1 = <&spi1_sleep>;

 	spiflash@0 {
 		compatible = "jedec,spi-nor";
 		reg = <0>;

 		/* May run faster once verified. */
 		spi-max-frequency = <10000000>;
 	};
 };

 &spi2 {
 	status = "okay";
 };

 &spi5 {
 	status = "okay";

 	cros_ec: ec@0 {
 		compatible = "google,cros-ec-spi";
 		reg = <0>;
 		interrupt-parent = <&gpio0>;
 		interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&ec_ap_int_l>;
 		spi-max-frequency = <3000000>;

 		i2c_tunnel: i2c-tunnel {
 			compatible = "google,cros-ec-i2c-tunnel";
 			google,remote-bus = <4>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 		};

 		usbc_extcon0: extcon0 {
 			compatible = "google,extcon-usbc-cros-ec";
 			google,usb-port-id = <0>;
 		};
 	};
 };

 &tsadc {
 	status = "okay";

 	rockchip,hw-tshut-mode = <1>; /* tshut mode 0:CRU 1:GPIO */
 	rockchip,hw-tshut-polarity = <1>; /* tshut polarity 0:LOW 1:HIGH */
 };

 &tcphy0 {
 	status = "okay";
 	extcon = <&usbc_extcon0>;
 };

 &u2phy0 {
 	status = "okay";
 };

 &u2phy0_host {
 	status = "okay";
 };

 &u2phy1_host {
 	status = "okay";
 };

 &u2phy0_otg {
 	status = "okay";
 };

 &u2phy1_otg {
 	status = "okay";
 };

 &uart2 {
 	status = "okay";
 };

 &usb_host0_ohci {
 	status = "okay";
 };

 &usbdrd3_0 {
 	status = "okay";
 	extcon = <&usbc_extcon0>;
 };

 &usbdrd_dwc3_0 {
 	status = "okay";
 	dr_mode = "host";
 };

 &vopb {
 	status = "okay";
 };

 &vopb_mmu {
 	status = "okay";
 };

 &vopl {
 	status = "okay";
 };

 &vopl_mmu {
 	status = "okay";
 };

 #include <arm/cros-ec-keyboard.dtsi>
 #include <arm/cros-ec-sbs.dtsi>

 &pinctrl {
 	/*
 	 * pinctrl settings for pins that have no real owners.
 	 *
 	 * At the moment settings are identical for S0 and S3, but if we later
 	 * need to configure things differently for S3 we'll adjust here.
 	 */
 	pinctrl-names = "default";
 	pinctrl-0 = <
 		&ap_pwroff	/* AP will auto-assert this when in S3 */
 		&clk_32k	/* This pin is always 32k on gru boards */
 	>;

 	pcfg_output_low: pcfg-output-low {
 		output-low;
 	};

 	pcfg_output_high: pcfg-output-high {
 		output-high;
 	};

 	pcfg_pull_none_8ma: pcfg-pull-none-8ma {
 		bias-disable;
 		drive-strength = <8>;
 	};

 	backlight-enable {
 		bl_en: bl-en {
 			rockchip,pins = <1 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>;
 		};
 	};

 	cros-ec {
 		ec_ap_int_l: ec-ap-int-l {
 			rockchip,pins = <0 RK_PA1 RK_FUNC_GPIO &pcfg_pull_up>;
 		};
 	};

 	discrete-regulators {
 		sd_io_pwr_en: sd-io-pwr-en {
 			rockchip,pins = <2 RK_PA2 RK_FUNC_GPIO
 					 &pcfg_pull_none>;
 		};

 		sd_pwr_1800_sel: sd-pwr-1800-sel {
 			rockchip,pins = <2 RK_PD4 RK_FUNC_GPIO
 					 &pcfg_pull_none>;
 		};

 		sd_slot_pwr_en: sd-slot-pwr-en {
 			rockchip,pins = <4 RK_PD5 RK_FUNC_GPIO
 					 &pcfg_pull_none>;
 		};
 	};

 	codec {
 		/* Has external pullup */
 		headset_int_l: headset-int-l {
 			rockchip,pins = <1 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>;
 		};

 		mic_int: mic-int {
 			rockchip,pins = <1 RK_PB5 RK_FUNC_GPIO &pcfg_pull_down>;
 		};
 	};

 	max98357a {
 		sdmode_en: sdmode-en {
 			rockchip,pins = <1 RK_PA2 RK_FUNC_GPIO &pcfg_pull_down>;
 		};
 	};

 	pcie {
 		pcie_clkreqn_cpm: pci-clkreqn-cpm {
 			/*
 			 * Since our pcie doesn't support ClockPM(CPM), we want
 			 * to hack this as gpio, so the EP could be able to
 			 * de-assert it along and make ClockPM(CPM) work.
 			 */
 			rockchip,pins = <2 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
 		};
 	};

 	sdmmc {
 		/*
 		 * We run sdmmc at max speed; bump up drive strength.
 		 * We also have external pulls, so disable the internal ones.
 		 */
 		sdmmc_bus4: sdmmc-bus4 {
 			rockchip,pins =
 				<4 RK_PB0 1 &pcfg_pull_none_8ma>,
 				<4 RK_PB1 1 &pcfg_pull_none_8ma>,
 				<4 RK_PB2 1 &pcfg_pull_none_8ma>,
 				<4 RK_PB3 1 &pcfg_pull_none_8ma>;
 		};

 		sdmmc_clk: sdmmc-clk {
 			rockchip,pins =
 				<4 RK_PB4 1 &pcfg_pull_none_8ma>;
 		};

 		sdmmc_cmd: sdmmc-cmd {
 			rockchip,pins =
 				<4 RK_PB5 1 &pcfg_pull_none_8ma>;
 		};

 		/*
 		 * In our case the official card detect is hooked to ground
 		 * to avoid getting access to JTAG just by sticking something
 		 * in the SD card slot (see the force_jtag bit in the TRM).
 		 *
 		 * We still configure it as card detect because it doesn't
 		 * hurt and dw_mmc will ignore it.  We make sure to disable
 		 * the pull though so we don't burn needless power.
 		 */
 		sdmmc_cd: sdmmc-cd {
 			rockchip,pins =
 				<0 RK_PA7 1 &pcfg_pull_none>;
 		};

 		/* This is where we actually hook up CD; has external pull */
 		sdmmc_cd_gpio: sdmmc-cd-gpio {
 			rockchip,pins = <4 RK_PD0 RK_FUNC_GPIO &pcfg_pull_none>;
 		};
 	};

 	spi1 {
 		spi1_sleep: spi1-sleep {
 			/*
 			 * Pull down SPI1 CLK/CS/RX/TX during suspend, to
 			 * prevent leakage.
 			 */
 			rockchip,pins = <1 RK_PB1 RK_FUNC_GPIO &pcfg_pull_down>,
 					<1 RK_PB2 RK_FUNC_GPIO &pcfg_pull_down>,
 					<1 RK_PA7 RK_FUNC_GPIO &pcfg_pull_down>,
 					<1 RK_PB0 RK_FUNC_GPIO &pcfg_pull_down>;
 		};
 	};

 	touchscreen {
 		touch_int_l: touch-int-l {
 			rockchip,pins = <3 RK_PB5 RK_FUNC_GPIO &pcfg_pull_up>;
 		};

 		touch_reset_l: touch-reset-l {
 			rockchip,pins = <4 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
 		};
 	};

 	trackpad {
 		ap_i2c_tp_pu_en: ap-i2c-tp-pu-en {
 			rockchip,pins = <3 RK_PB4 RK_FUNC_GPIO &pcfg_output_high>;
 		};

 		trackpad_int_l: trackpad-int-l {
 			rockchip,pins = <1 RK_PA4 RK_FUNC_GPIO &pcfg_pull_up>;
 		};
 	};

 	wifi: wifi {
 		wlan_module_reset_l: wlan-module-reset-l {
 			rockchip,pins = <1 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>;
 		};

 		bt_host_wake_l: bt-host-wake-l {
 			/* Kevin has an external pull up, but Gru does not */
 			rockchip,pins = <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
 		};
 	};

 	write-protect {
 		ap_fw_wp: ap-fw-wp {
 			rockchip,pins = <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_up>;
 		};
 	};
 };
	// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
	/*
	* Google Gru (and derivatives) board device tree source
	*
	* Copyright 2016-2017 Google, Inc
	*/

	#include <dt-bindings/input/input.h>
	#include "rk3399.dtsi"
	#include "rk3399-op1-opp.dtsi"

	/ {
	chosen {
	stdout-path = "serial2:115200n8";
	};

	/*
	* Power Tree
	*
	* In general an attempt is made to include all rails called out by
	* the schematic as long as those rails interact in some way with
	* the AP. AKA:
	* - Rails that only connect to the EC (or devices that the EC talks to)
	* are not included.
	* - Rails _are_ included if the rails go to the AP even if the AP
	* doesn't currently care about them / they are always on. The idea
	* here is that it makes it easier to map to the schematic or extend
	* later.
	*
	* If two rails are substantially the same from the AP's point of
	* view, though, we won't create a full fixed regulator. We'll just
	* put the child rail as an alias of the parent rail. Sometimes rails
	* look the same to the AP because one of these is true:
	* - The EC controls the enable and the EC always enables a rail as
	* long as the AP is running.
	* - The rails are actually connected to each other by a jumper and
	* the distinction is just there to add clarity/flexibility to the
	* schematic.
	*/

	ppvar_sys: ppvar-sys {
	compatible = "regulator-fixed";
	regulator-name = "ppvar_sys";
	regulator-always-on;
	regulator-boot-on;
	};

	pp1200_lpddr: pp1200-lpddr {
	compatible = "regulator-fixed";
	regulator-name = "pp1200_lpddr";

	/* EC turns on w/ lpddr_pwr_en; always on for AP */
	regulator-always-on;
	regulator-boot-on;
	regulator-min-microvolt = <1200000>;
	regulator-max-microvolt = <1200000>;

	vin-supply = <&ppvar_sys>;
	};

	pp1800: pp1800 {
	compatible = "regulator-fixed";
	regulator-name = "pp1800";

	/* Always on when ppvar_sys shows power good */
	regulator-always-on;
	regulator-boot-on;
	regulator-min-microvolt = <1800000>;
	regulator-max-microvolt = <1800000>;

	vin-supply = <&ppvar_sys>;
	};

	pp3300: pp3300 {
	compatible = "regulator-fixed";
	regulator-name = "pp3300";

	/* Always on; plain and simple */
	regulator-always-on;
	regulator-boot-on;
	regulator-min-microvolt = <3300000>;
	regulator-max-microvolt = <3300000>;

	vin-supply = <&ppvar_sys>;
	};

	pp5000: pp5000 {
	compatible = "regulator-fixed";
	regulator-name = "pp5000";

	/* EC turns on w/ pp5000_en; always on for AP */
	regulator-always-on;
	regulator-boot-on;
	regulator-min-microvolt = <5000000>;
	regulator-max-microvolt = <5000000>;

	vin-supply = <&ppvar_sys>;
	};

	ppvar_bigcpu_pwm: ppvar-bigcpu-pwm {
	compatible = "pwm-regulator";
	regulator-name = "ppvar_bigcpu_pwm";

	pwms = <&pwm1 0 3337 0>;
	pwm-supply = <&ppvar_sys>;
	pwm-dutycycle-range = <100 0>;
	pwm-dutycycle-unit = <100>;

	/* EC turns on w/ ap_core_en; always on for AP */
	regulator-always-on;
	regulator-boot-on;
	regulator-min-microvolt = <800107>;
	regulator-max-microvolt = <1302232>;
	};

	ppvar_bigcpu: ppvar-bigcpu {
	compatible = "vctrl-regulator";
	regulator-name = "ppvar_bigcpu";

	regulator-min-microvolt = <800107>;
	regulator-max-microvolt = <1302232>;

	ctrl-supply = <&ppvar_bigcpu_pwm>;
	ctrl-voltage-range = <800107 1302232>;

	regulator-settling-time-up-us = <322>;
	};

	ppvar_litcpu_pwm: ppvar-litcpu-pwm {
	compatible = "pwm-regulator";
	regulator-name = "ppvar_litcpu_pwm";

	pwms = <&pwm2 0 3337 0>;
	pwm-supply = <&ppvar_sys>;
	pwm-dutycycle-range = <100 0>;
	pwm-dutycycle-unit = <100>;

	/* EC turns on w/ ap_core_en; always on for AP */
	regulator-always-on;
	regulator-boot-on;
	regulator-min-microvolt = <797743>;
	regulator-max-microvolt = <1307837>;
	};

	ppvar_litcpu: ppvar-litcpu {
	compatible = "vctrl-regulator";
	regulator-name = "ppvar_litcpu";

	regulator-min-microvolt = <797743>;
	regulator-max-microvolt = <1307837>;

	ctrl-supply = <&ppvar_litcpu_pwm>;
	ctrl-voltage-range = <797743 1307837>;

	regulator-settling-time-up-us = <384>;
	};

	ppvar_gpu_pwm: ppvar-gpu-pwm {
	compatible = "pwm-regulator";
	regulator-name = "ppvar_gpu_pwm";

	pwms = <&pwm0 0 3337 0>;
	pwm-supply = <&ppvar_sys>;
	pwm-dutycycle-range = <100 0>;
	pwm-dutycycle-unit = <100>;

	/* EC turns on w/ ap_core_en; always on for AP */
	regulator-always-on;
	regulator-boot-on;
	regulator-min-microvolt = <786384>;
	regulator-max-microvolt = <1217747>;
	};

	ppvar_gpu: ppvar-gpu {
	compatible = "vctrl-regulator";
	regulator-name = "ppvar_gpu";

	regulator-min-microvolt = <786384>;
	regulator-max-microvolt = <1217747>;

	ctrl-supply = <&ppvar_gpu_pwm>;
	ctrl-voltage-range = <786384 1217747>;

	regulator-settling-time-up-us = <390>;
	};

	/* EC turns on w/ pp900_ddrpll_en */
	pp900_ddrpll: pp900-ap {
	};

	/* EC turns on w/ pp900_pll_en */
	pp900_pll: pp900-ap {
	};

	/* EC turns on w/ pp900_pmu_en */
	pp900_pmu: pp900-ap {
	};

	/* EC turns on w/ pp1800_s0_en_l */
	pp1800_ap_io: pp1800_emmc: pp1800_nfc: pp1800_s0: pp1800 {
	};

	/* EC turns on w/ pp1800_avdd_en_l */
	pp1800_avdd: pp1800 {
	};

	/* EC turns on w/ pp1800_lid_en_l */
	pp1800_lid: pp1800_mic: pp1800 {
	};

	/* EC turns on w/ lpddr_pwr_en */
	pp1800_lpddr: pp1800 {
	};

	/* EC turns on w/ pp1800_pmu_en_l */
	pp1800_pmu: pp1800 {
	};

	/* EC turns on w/ pp1800_usb_en_l */
	pp1800_usb: pp1800 {
	};

	pp3000_sd_slot: pp3000-sd-slot {
	compatible = "regulator-fixed";
	regulator-name = "pp3000_sd_slot";
	pinctrl-names = "default";
	pinctrl-0 = <&sd_slot_pwr_en>;

	enable-active-high;
	gpio = <&gpio4 29 GPIO_ACTIVE_HIGH>;

	vin-supply = <&pp3000>;
	};

	/*
	* Technically, this is a small abuse of 'regulator-gpio'; this
	* regulator is a mux between pp1800 and pp3300. pp1800 and pp3300 are
	* always on though, so it is sufficient to simply control the mux
	* here.
	*/
	ppvar_sd_card_io: ppvar-sd-card-io {
	compatible = "regulator-gpio";
	regulator-name = "ppvar_sd_card_io";
	pinctrl-names = "default";
	pinctrl-0 = <&sd_io_pwr_en &sd_pwr_1800_sel>;

	enable-active-high;
	enable-gpio = <&gpio2 2 GPIO_ACTIVE_HIGH>;
	gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>;
	states = <1800000 0x1
	3000000 0x0>;

	regulator-min-microvolt = <1800000>;
	regulator-max-microvolt = <3000000>;
	};

	/* EC turns on w/ pp3300_trackpad_en_l */
	pp3300_trackpad: pp3300-trackpad {
	};

	/* EC turns on w/ usb_a_en */
	pp5000_usb_a_vbus: pp5000 {
	};

	ap_rtc_clk: ap-rtc-clk {
	compatible = "fixed-clock";
	clock-frequency = <32768>;
	clock-output-names = "xin32k";
	#clock-cells = <0>;
	};

	max98357a: max98357a {
	compatible = "maxim,max98357a";
	pinctrl-names = "default";
	pinctrl-0 = <&sdmode_en>;
	sdmode-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
	sdmode-delay = <2>;
	#sound-dai-cells = <0>;
	status = "okay";
	};

	sound: sound {
	compatible = "rockchip,rk3399-gru-sound";
	rockchip,cpu = <&i2s0 &i2s2>;
	};
	};

	&cdn_dp {
	status = "okay";
	};

	/*
	* Set some suspend operating points to avoid OVP in suspend
	*
	* When we go into S3 ARM Trusted Firmware will transition our PWM regulators
	* from wherever they're at back to the "default" operating point (whatever
	* voltage we get when we set the PWM pins to "input").
	*
	* This quick transition under light load has the possibility to trigger the
	* regulator "over voltage protection" (OVP).
	*
	* To make extra certain that we don't hit this OVP at suspend time, we'll
	* transition to a voltage that's much closer to the default (~1.0 V) so that
	* there will not be a big jump. Technically we only need to get within 200 mV
	* of the default voltage, but the speed here should be fast enough and we need
	* suspend/resume to be rock solid.
	*/

	&cluster0_opp {
	opp05 {
	opp-suspend;
	};
	};

	&cluster1_opp {
	opp06 {
	opp-suspend;
	};
	};

	&cpu_l0 {
	cpu-supply = <&ppvar_litcpu>;
	};

	&cpu_l1 {
	cpu-supply = <&ppvar_litcpu>;
	};

	&cpu_l2 {
	cpu-supply = <&ppvar_litcpu>;
	};

	&cpu_l3 {
	cpu-supply = <&ppvar_litcpu>;
	};

	&cpu_b0 {
	cpu-supply = <&ppvar_bigcpu>;
	};

	&cpu_b1 {
	cpu-supply = <&ppvar_bigcpu>;
	};


	&cru {
	assigned-clocks =
	<&cru PLL_GPLL>, <&cru PLL_CPLL>,
	<&cru PLL_NPLL>,
	<&cru ACLK_PERIHP>, <&cru HCLK_PERIHP>,
	<&cru PCLK_PERIHP>,
	<&cru ACLK_PERILP0>, <&cru HCLK_PERILP0>,
	<&cru PCLK_PERILP0>, <&cru ACLK_CCI>,
	<&cru HCLK_PERILP1>, <&cru PCLK_PERILP1>,
	<&cru ACLK_VIO>, <&cru ACLK_HDCP>,
	<&cru ACLK_GIC_PRE>,
	<&cru PCLK_DDR>;
	assigned-clock-rates =
	<600000000>, <800000000>,
	<1000000000>,
	<150000000>, <75000000>,
	<37500000>,
	<100000000>, <100000000>,
	<50000000>, <800000000>,
	<100000000>, <50000000>,
	<400000000>, <400000000>,
	<200000000>,
	<200000000>;
	};

	&emmc_phy {
	status = "okay";
	};

	&gpu {
	mali-supply = <&ppvar_gpu>;
	status = "okay";
	};

	ap_i2c_ts: &i2c3 {
	status = "okay";

	clock-frequency = <400000>;

	/* These are relatively safe rise/fall times */
	i2c-scl-falling-time-ns = <50>;
	i2c-scl-rising-time-ns = <300>;
	};

	ap_i2c_audio: &i2c8 {
	status = "okay";

	clock-frequency = <400000>;

	/* These are relatively safe rise/fall times */
	i2c-scl-falling-time-ns = <50>;
	i2c-scl-rising-time-ns = <300>;

	codec: da7219@1a {
	compatible = "dlg,da7219";
	reg = <0x1a>;
	interrupt-parent = <&gpio1>;
	interrupts = <23 IRQ_TYPE_LEVEL_LOW>;
	clocks = <&cru SCLK_I2S_8CH_OUT>;
	clock-names = "mclk";
	dlg,micbias-lvl = <2600>;
	dlg,mic-amp-in-sel = "diff";
	pinctrl-names = "default";
	pinctrl-0 = <&headset_int_l>;
	VDD-supply = <&pp1800>;
	VDDMIC-supply = <&pp3300>;
	VDDIO-supply = <&pp1800>;

	da7219_aad {
	dlg,adc-1bit-rpt = <1>;
	dlg,btn-avg = <4>;
	dlg,btn-cfg = <50>;
	dlg,mic-det-thr = <500>;
	dlg,jack-ins-deb = <20>;
	dlg,jack-det-rate = "32ms_64ms";
	dlg,jack-rem-deb = <1>;

	dlg,a-d-btn-thr = <0xa>;
	dlg,d-b-btn-thr = <0x16>;
	dlg,b-c-btn-thr = <0x21>;
	dlg,c-mic-btn-thr = <0x3E>;
	};
	};
	};

	&i2s0 {
	status = "okay";
	};

	&i2s2 {
	status = "okay";
	};

	&io_domains {
	status = "okay";

	audio-supply = <&pp1800_audio>; /* APIO5_VDD; 3d 4a */
	bt656-supply = <&pp1800_ap_io>; /* APIO2_VDD; 2a 2b */
	gpio1830-supply = <&pp3000_ap>; /* APIO4_VDD; 4c 4d */
	sdmmc-supply = <&ppvar_sd_card_io>; /* SDMMC0_VDD; 4b */
	};

	&pcie0 {
	status = "okay";

	ep-gpios = <&gpio2 27 GPIO_ACTIVE_HIGH>;
	pinctrl-names = "default";
	pinctrl-0 = <&pcie_clkreqn_cpm>, <&wifi_perst_l>;
	vpcie3v3-supply = <&pp3300_wifi_bt>;
	vpcie1v8-supply = <&wlan_pd_n>; /* HACK: see &wlan_pd_n */
	vpcie0v9-supply = <&pp900_pcie>;

	pci_rootport: pcie@0,0 {
	reg = <0x83000000 0x0 0x00000000 0x0 0x00000000>;
	#address-cells = <3>;
	#size-cells = <2>;
	ranges;
	};
	};

	&pcie_phy {
	status = "okay";
	};

	&pmu_io_domains {
	status = "okay";

	pmu1830-supply = <&pp1800_pmu>; /* PMUIO2_VDD */
	};

	&pwm0 {
	status = "okay";
	};

	&pwm1 {
	status = "okay";
	};

	&pwm2 {
	status = "okay";
	};

	&pwm3 {
	status = "okay";
	};

	&sdhci {
	/*
	* Signal integrity isn't great at 200 MHz and 150 MHz (DDR) gives the
	* same (or nearly the same) performance for all eMMC that are intended
	* to be used.
	*/
	assigned-clock-rates = <150000000>;

	bus-width = <8>;
	mmc-hs400-1_8v;
	mmc-hs400-enhanced-strobe;
	non-removable;
	status = "okay";
	};

	&sdmmc {
	status = "okay";

	/*
	* Note: configure "sdmmc_cd" as card detect even though it's actually
	* hooked to ground. Because we specified "cd-gpios" below dw_mmc
	* should be ignoring card detect anyway. Specifying the pin as
	* sdmmc_cd means that even if you've got GRF_SOC_CON7[12] (force_jtag)
	* turned on that the system will still make sure the port is
	* configured as SDMMC and not JTAG.
	*/
	pinctrl-names = "default";
	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_cd_gpio
	&sdmmc_bus4>;

	bus-width = <4>;
	cap-mmc-highspeed;
	cap-sd-highspeed;
	cd-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>;
	disable-wp;
	sd-uhs-sdr12;
	sd-uhs-sdr25;
	sd-uhs-sdr50;
	sd-uhs-sdr104;
	vmmc-supply = <&pp3000_sd_slot>;
	vqmmc-supply = <&ppvar_sd_card_io>;
	};

	&spi1 {
	status = "okay";

	pinctrl-names = "default", "sleep";
	pinctrl-1 = <&spi1_sleep>;

	spiflash@0 {
	compatible = "jedec,spi-nor";
	reg = <0>;

	/* May run faster once verified. */
	spi-max-frequency = <10000000>;
	};
	};

	&spi2 {
	status = "okay";
	};

	&spi5 {
	status = "okay";

	cros_ec: ec@0 {
	compatible = "google,cros-ec-spi";
	reg = <0>;
	interrupt-parent = <&gpio0>;
	interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
	pinctrl-names = "default";
	pinctrl-0 = <&ec_ap_int_l>;
	spi-max-frequency = <3000000>;

	i2c_tunnel: i2c-tunnel {
	compatible = "google,cros-ec-i2c-tunnel";
	google,remote-bus = <4>;
	#address-cells = <1>;
	#size-cells = <0>;
	};

	usbc_extcon0: extcon0 {
	compatible = "google,extcon-usbc-cros-ec";
	google,usb-port-id = <0>;
	};
	};
	};

	&tsadc {
	status = "okay";

	rockchip,hw-tshut-mode = <1>; /* tshut mode 0:CRU 1:GPIO */
	rockchip,hw-tshut-polarity = <1>; /* tshut polarity 0:LOW 1:HIGH */
	};

	&tcphy0 {
	status = "okay";
	extcon = <&usbc_extcon0>;
	};

	&u2phy0 {
	status = "okay";
	};

	&u2phy0_host {
	status = "okay";
	};

	&u2phy1_host {
	status = "okay";
	};

	&u2phy0_otg {
	status = "okay";
	};

	&u2phy1_otg {
	status = "okay";
	};

	&uart2 {
	status = "okay";
	};

	&usb_host0_ohci {
	status = "okay";
	};

	&usbdrd3_0 {
	status = "okay";
	extcon = <&usbc_extcon0>;
	};

	&usbdrd_dwc3_0 {
	status = "okay";
	dr_mode = "host";
	};

	&vopb {
	status = "okay";
	};

	&vopb_mmu {
	status = "okay";
	};

	&vopl {
	status = "okay";
	};

	&vopl_mmu {
	status = "okay";
	};

	#include <arm/cros-ec-keyboard.dtsi>
	#include <arm/cros-ec-sbs.dtsi>

	&pinctrl {
	/*
	* pinctrl settings for pins that have no real owners.
	*
	* At the moment settings are identical for S0 and S3, but if we later
	* need to configure things differently for S3 we'll adjust here.
	*/
	pinctrl-names = "default";
	pinctrl-0 = <
	&ap_pwroff /* AP will auto-assert this when in S3 */
	&clk_32k /* This pin is always 32k on gru boards */
	>;

	pcfg_output_low: pcfg-output-low {
	output-low;
	};

	pcfg_output_high: pcfg-output-high {
	output-high;
	};

	pcfg_pull_none_8ma: pcfg-pull-none-8ma {
	bias-disable;
	drive-strength = <8>;
	};

	backlight-enable {
	bl_en: bl-en {
	rockchip,pins = <1 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>;
	};
	};

	cros-ec {
	ec_ap_int_l: ec-ap-int-l {
	rockchip,pins = <0 RK_PA1 RK_FUNC_GPIO &pcfg_pull_up>;
	};
	};

	discrete-regulators {
	sd_io_pwr_en: sd-io-pwr-en {
	rockchip,pins = <2 RK_PA2 RK_FUNC_GPIO
	&pcfg_pull_none>;
	};

	sd_pwr_1800_sel: sd-pwr-1800-sel {
	rockchip,pins = <2 RK_PD4 RK_FUNC_GPIO
	&pcfg_pull_none>;
	};

	sd_slot_pwr_en: sd-slot-pwr-en {
	rockchip,pins = <4 RK_PD5 RK_FUNC_GPIO
	&pcfg_pull_none>;
	};
	};

	codec {
	/* Has external pullup */
	headset_int_l: headset-int-l {
	rockchip,pins = <1 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>;
	};

	mic_int: mic-int {
	rockchip,pins = <1 RK_PB5 RK_FUNC_GPIO &pcfg_pull_down>;
	};
	};

	max98357a {
	sdmode_en: sdmode-en {
	rockchip,pins = <1 RK_PA2 RK_FUNC_GPIO &pcfg_pull_down>;
	};
	};

	pcie {
	pcie_clkreqn_cpm: pci-clkreqn-cpm {
	/*
	* Since our pcie doesn't support ClockPM(CPM), we want
	* to hack this as gpio, so the EP could be able to
	* de-assert it along and make ClockPM(CPM) work.
	*/
	rockchip,pins = <2 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
	};
	};

	sdmmc {
	/*
	* We run sdmmc at max speed; bump up drive strength.
	* We also have external pulls, so disable the internal ones.
	*/
	sdmmc_bus4: sdmmc-bus4 {
	rockchip,pins =
	<4 RK_PB0 1 &pcfg_pull_none_8ma>,
	<4 RK_PB1 1 &pcfg_pull_none_8ma>,
	<4 RK_PB2 1 &pcfg_pull_none_8ma>,
	<4 RK_PB3 1 &pcfg_pull_none_8ma>;
	};

	sdmmc_clk: sdmmc-clk {
	rockchip,pins =
	<4 RK_PB4 1 &pcfg_pull_none_8ma>;
	};

	sdmmc_cmd: sdmmc-cmd {
	rockchip,pins =
	<4 RK_PB5 1 &pcfg_pull_none_8ma>;
	};

	/*
	* In our case the official card detect is hooked to ground
	* to avoid getting access to JTAG just by sticking something
	* in the SD card slot (see the force_jtag bit in the TRM).
	*
	* We still configure it as card detect because it doesn't
	* hurt and dw_mmc will ignore it. We make sure to disable
	* the pull though so we don't burn needless power.
	*/
	sdmmc_cd: sdmmc-cd {
	rockchip,pins =
	<0 RK_PA7 1 &pcfg_pull_none>;
	};

	/* This is where we actually hook up CD; has external pull */
	sdmmc_cd_gpio: sdmmc-cd-gpio {
	rockchip,pins = <4 RK_PD0 RK_FUNC_GPIO &pcfg_pull_none>;
	};
	};

	spi1 {
	spi1_sleep: spi1-sleep {
	/*
	* Pull down SPI1 CLK/CS/RX/TX during suspend, to
	* prevent leakage.
	*/
	rockchip,pins = <1 RK_PB1 RK_FUNC_GPIO &pcfg_pull_down>,
	<1 RK_PB2 RK_FUNC_GPIO &pcfg_pull_down>,
	<1 RK_PA7 RK_FUNC_GPIO &pcfg_pull_down>,
	<1 RK_PB0 RK_FUNC_GPIO &pcfg_pull_down>;
	};
	};

	touchscreen {
	touch_int_l: touch-int-l {
	rockchip,pins = <3 RK_PB5 RK_FUNC_GPIO &pcfg_pull_up>;
	};

	touch_reset_l: touch-reset-l {
	rockchip,pins = <4 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
	};
	};

	trackpad {
	ap_i2c_tp_pu_en: ap-i2c-tp-pu-en {
	rockchip,pins = <3 RK_PB4 RK_FUNC_GPIO &pcfg_output_high>;
	};

	trackpad_int_l: trackpad-int-l {
	rockchip,pins = <1 RK_PA4 RK_FUNC_GPIO &pcfg_pull_up>;
	};
	};

	wifi: wifi {
	wlan_module_reset_l: wlan-module-reset-l {
	rockchip,pins = <1 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>;
	};

	bt_host_wake_l: bt-host-wake-l {
	/* Kevin has an external pull up, but Gru does not */
	rockchip,pins = <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
	};
	};

	write-protect {
	ap_fw_wp: ap-fw-wp {
	rockchip,pins = <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_up>;
	};
	};
	};