| // SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| /* |
| * Copyright (c) 2017 Fuzhou Rockchip Electronics Co., Ltd. |
| * Copyright (c) 2018 Akash Gajjar <Akash_Gajjar@mentor.com> |
| * Copyright (c) 2020 Tobias Schramm <t.schramm@manjaro.org> |
| */ |
| |
| /dts-v1/; |
| #include <dt-bindings/input/gpio-keys.h> |
| #include <dt-bindings/input/linux-event-codes.h> |
| #include <dt-bindings/pwm/pwm.h> |
| #include <dt-bindings/usb/pd.h> |
| #include <dt-bindings/leds/common.h> |
| #include "rk3399.dtsi" |
| #include "rk3399-opp.dtsi" |
| |
| / { |
| model = "Pine64 Pinebook Pro"; |
| compatible = "pine64,pinebook-pro", "rockchip,rk3399"; |
| |
| chosen { |
| stdout-path = "serial2:1500000n8"; |
| }; |
| |
| backlight: edp-backlight { |
| compatible = "pwm-backlight"; |
| power-supply = <&vcc_12v>; |
| pwms = <&pwm0 0 740740 0>; |
| }; |
| |
| edp_panel: edp-panel { |
| compatible = "boe,nv140fhmn49"; |
| backlight = <&backlight>; |
| enable-gpios = <&gpio1 RK_PA0 GPIO_ACTIVE_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&panel_en_gpio>; |
| power-supply = <&vcc3v3_panel>; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| panel_in_edp: endpoint@0 { |
| reg = <0>; |
| remote-endpoint = <&edp_out_panel>; |
| }; |
| }; |
| }; |
| }; |
| |
| /* |
| * Use separate nodes for gpio-keys to allow for selective deactivation |
| * of wakeup sources via sysfs without disabling the whole key |
| */ |
| gpio-key-lid { |
| compatible = "gpio-keys"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&lidbtn_gpio>; |
| |
| lid { |
| debounce-interval = <20>; |
| gpios = <&gpio1 RK_PA1 GPIO_ACTIVE_LOW>; |
| label = "Lid"; |
| linux,code = <SW_LID>; |
| linux,input-type = <EV_SW>; |
| wakeup-event-action = <EV_ACT_DEASSERTED>; |
| wakeup-source; |
| }; |
| }; |
| |
| gpio-key-power { |
| compatible = "gpio-keys"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pwrbtn_gpio>; |
| |
| power { |
| debounce-interval = <20>; |
| gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>; |
| label = "Power"; |
| linux,code = <KEY_POWER>; |
| wakeup-source; |
| }; |
| }; |
| |
| leds { |
| compatible = "gpio-leds"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pwr_led_pin &slp_led_pin>; |
| |
| green_led: led-0 { |
| color = <LED_COLOR_ID_GREEN>; |
| default-state = "on"; |
| function = LED_FUNCTION_POWER; |
| gpios = <&gpio0 RK_PB3 GPIO_ACTIVE_HIGH>; |
| label = "green:power"; |
| }; |
| |
| red_led: led-1 { |
| color = <LED_COLOR_ID_RED>; |
| default-state = "off"; |
| function = LED_FUNCTION_STANDBY; |
| gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_HIGH>; |
| label = "red:standby"; |
| panic-indicator; |
| retain-state-suspended; |
| }; |
| }; |
| |
| /* Power sequence for SDIO WiFi module */ |
| sdio_pwrseq: sdio-pwrseq { |
| compatible = "mmc-pwrseq-simple"; |
| clocks = <&rk808 1>; |
| clock-names = "ext_clock"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&wifi_enable_h_gpio>; |
| post-power-on-delay-ms = <100>; |
| power-off-delay-us = <500000>; |
| |
| /* WL_REG_ON on module */ |
| reset-gpios = <&gpio0 RK_PB2 GPIO_ACTIVE_LOW>; |
| }; |
| |
| /* Audio components */ |
| es8316-sound { |
| compatible = "simple-audio-card"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&hp_det_gpio>; |
| simple-audio-card,name = "rockchip,es8316-codec"; |
| simple-audio-card,format = "i2s"; |
| simple-audio-card,mclk-fs = <256>; |
| |
| simple-audio-card,widgets = |
| "Microphone", "Mic Jack", |
| "Headphone", "Headphones", |
| "Speaker", "Speaker"; |
| simple-audio-card,routing = |
| "MIC1", "Mic Jack", |
| "Headphones", "HPOL", |
| "Headphones", "HPOR", |
| "Speaker Amplifier INL", "HPOL", |
| "Speaker Amplifier INR", "HPOR", |
| "Speaker", "Speaker Amplifier OUTL", |
| "Speaker", "Speaker Amplifier OUTR"; |
| |
| simple-audio-card,hp-det-gpio = <&gpio0 RK_PB0 GPIO_ACTIVE_HIGH>; |
| simple-audio-card,aux-devs = <&speaker_amp>; |
| simple-audio-card,pin-switches = "Speaker"; |
| |
| simple-audio-card,cpu { |
| sound-dai = <&i2s1>; |
| }; |
| |
| simple-audio-card,codec { |
| sound-dai = <&es8316>; |
| }; |
| }; |
| |
| speaker_amp: speaker-amplifier { |
| compatible = "simple-audio-amplifier"; |
| enable-gpios = <&gpio4 RK_PD3 GPIO_ACTIVE_HIGH>; |
| sound-name-prefix = "Speaker Amplifier"; |
| VCC-supply = <&pa_5v>; |
| }; |
| |
| /* Power tree */ |
| /* Root power source */ |
| vcc_sysin: vcc-sysin { |
| compatible = "regulator-fixed"; |
| regulator-name = "vcc_sysin"; |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| /* Regulators supplied by vcc_sysin */ |
| /* LCD backlight supply */ |
| vcc_12v: vcc-12v { |
| compatible = "regulator-fixed"; |
| regulator-name = "vcc_12v"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <12000000>; |
| regulator-max-microvolt = <12000000>; |
| vin-supply = <&vcc_sysin>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| /* Main 3.3 V supply */ |
| vcc3v3_sys: wifi_bat: vcc3v3-sys { |
| compatible = "regulator-fixed"; |
| regulator-name = "vcc3v3_sys"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| vin-supply = <&vcc_sysin>; |
| |
| regulator-state-mem { |
| regulator-on-in-suspend; |
| }; |
| }; |
| |
| /* 5 V USB power supply */ |
| vcc5v0_usb: pa_5v: vcc5v0-usb-regulator { |
| compatible = "regulator-fixed"; |
| enable-active-high; |
| gpio = <&gpio1 RK_PB5 GPIO_ACTIVE_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pwr_5v_gpio>; |
| regulator-name = "vcc5v0_usb"; |
| regulator-always-on; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| vin-supply = <&vcc_sysin>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| /* RK3399 logic supply */ |
| vdd_log: vdd-log { |
| compatible = "pwm-regulator"; |
| pwms = <&pwm2 0 25000 1>; |
| regulator-name = "vdd_log"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <800000>; |
| regulator-max-microvolt = <1400000>; |
| vin-supply = <&vcc_sysin>; |
| |
| regulator-state-mem { |
| regulator-on-in-suspend; |
| }; |
| }; |
| |
| /* Regulators supplied by vcc3v3_sys */ |
| /* 0.9 V supply, always on */ |
| vcc_0v9: vcc-0v9 { |
| compatible = "regulator-fixed"; |
| regulator-name = "vcc_0v9"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <900000>; |
| regulator-max-microvolt = <900000>; |
| vin-supply = <&vcc3v3_sys>; |
| }; |
| |
| /* S3 1.8 V supply, switched by vcc1v8_s3 */ |
| vcca1v8_s3: vcc1v8-s3 { |
| compatible = "regulator-fixed"; |
| regulator-name = "vcca1v8_s3"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| vin-supply = <&vcc3v3_sys>; |
| }; |
| |
| /* micro SD card power */ |
| vcc3v0_sd: vcc3v0-sd { |
| compatible = "regulator-fixed"; |
| enable-active-high; |
| gpio = <&gpio0 RK_PA1 GPIO_ACTIVE_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&sdmmc0_pwr_h_gpio>; |
| regulator-name = "vcc3v0_sd"; |
| regulator-always-on; |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3000000>; |
| vin-supply = <&vcc3v3_sys>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| /* LCD panel power, called VCC3V3_S0 in schematic */ |
| vcc3v3_panel: vcc3v3-panel { |
| compatible = "regulator-fixed"; |
| enable-active-high; |
| gpio = <&gpio1 RK_PC6 GPIO_ACTIVE_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&lcdvcc_en_gpio>; |
| regulator-name = "vcc3v3_panel"; |
| regulator-always-on; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-enable-ramp-delay = <100000>; |
| vin-supply = <&vcc3v3_sys>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| /* M.2 adapter power, switched by vcc1v8_s3 */ |
| vcc3v3_ssd: vcc3v3-ssd { |
| compatible = "regulator-fixed"; |
| regulator-name = "vcc3v3_ssd"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| vin-supply = <&vcc3v3_sys>; |
| }; |
| |
| /* Regulators supplied by vcc5v0_usb */ |
| /* USB 3 port power supply regulator */ |
| vcc5v0_otg: vcc5v0-otg { |
| compatible = "regulator-fixed"; |
| enable-active-high; |
| gpio = <&gpio4 RK_PD2 GPIO_ACTIVE_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&vcc5v0_host_en_gpio>; |
| regulator-name = "vcc5v0_otg"; |
| regulator-always-on; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| vin-supply = <&vcc5v0_usb>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| /* Regulators supplied by vcc5v0_usb */ |
| /* Type C port power supply regulator */ |
| vbus_5vout: vbus_typec: vbus-5vout { |
| compatible = "regulator-fixed"; |
| enable-active-high; |
| gpio = <&gpio1 RK_PA3 GPIO_ACTIVE_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&vcc5v0_typec0_en_gpio>; |
| regulator-name = "vbus_5vout"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| vin-supply = <&vcc5v0_usb>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| /* Regulators supplied by vcc_1v8 */ |
| /* Primary 0.9 V LDO */ |
| vcca0v9_s3: vcca0v9-s3 { |
| compatible = "regulator-fixed"; |
| regulator-name = "vcc0v9_s3"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| vin-supply = <&vcc_1v8>; |
| |
| regulator-state-mem { |
| regulator-on-in-suspend; |
| }; |
| }; |
| |
| mains_charger: dc-charger { |
| compatible = "gpio-charger"; |
| charger-type = "mains"; |
| gpios = <&gpio4 RK_PD0 GPIO_ACTIVE_LOW>; |
| |
| /* Also triggered by USB charger */ |
| pinctrl-names = "default"; |
| pinctrl-0 = <&dc_det_gpio>; |
| }; |
| }; |
| |
| &cdn_dp { |
| status = "okay"; |
| }; |
| |
| &cpu_b0 { |
| cpu-supply = <&vdd_cpu_b>; |
| }; |
| |
| &cpu_b1 { |
| cpu-supply = <&vdd_cpu_b>; |
| }; |
| |
| &cpu_l0 { |
| cpu-supply = <&vdd_cpu_l>; |
| }; |
| |
| &cpu_l1 { |
| cpu-supply = <&vdd_cpu_l>; |
| }; |
| |
| &cpu_l2 { |
| cpu-supply = <&vdd_cpu_l>; |
| }; |
| |
| &cpu_l3 { |
| cpu-supply = <&vdd_cpu_l>; |
| }; |
| |
| &edp { |
| force-hpd; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&edp_hpd>; |
| status = "okay"; |
| |
| ports { |
| edp_out: port@1 { |
| reg = <1>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| edp_out_panel: endpoint@0 { |
| reg = <0>; |
| remote-endpoint = <&panel_in_edp>; |
| }; |
| }; |
| }; |
| }; |
| |
| &emmc_phy { |
| status = "okay"; |
| }; |
| |
| &gpu { |
| mali-supply = <&vdd_gpu>; |
| status = "okay"; |
| }; |
| |
| &hdmi_sound { |
| status = "okay"; |
| }; |
| |
| &i2c0 { |
| clock-frequency = <400000>; |
| i2c-scl-falling-time-ns = <4>; |
| i2c-scl-rising-time-ns = <168>; |
| status = "okay"; |
| |
| rk808: pmic@1b { |
| compatible = "rockchip,rk808"; |
| reg = <0x1b>; |
| #clock-cells = <1>; |
| clock-output-names = "xin32k", "rk808-clkout2"; |
| interrupt-parent = <&gpio3>; |
| interrupts = <10 IRQ_TYPE_LEVEL_LOW>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pmic_int_l_gpio>; |
| rockchip,system-power-controller; |
| wakeup-source; |
| |
| vcc1-supply = <&vcc_sysin>; |
| vcc2-supply = <&vcc_sysin>; |
| vcc3-supply = <&vcc_sysin>; |
| vcc4-supply = <&vcc_sysin>; |
| vcc6-supply = <&vcc_sysin>; |
| vcc7-supply = <&vcc_sysin>; |
| vcc8-supply = <&vcc3v3_sys>; |
| vcc9-supply = <&vcc_sysin>; |
| vcc10-supply = <&vcc_sysin>; |
| vcc11-supply = <&vcc_sysin>; |
| vcc12-supply = <&vcc3v3_sys>; |
| vcc13-supply = <&vcc_sysin>; |
| vcc14-supply = <&vcc_sysin>; |
| |
| regulators { |
| /* rk3399 center logic supply */ |
| vdd_center: DCDC_REG1 { |
| regulator-name = "vdd_center"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <750000>; |
| regulator-max-microvolt = <1350000>; |
| regulator-ramp-delay = <6001>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| vdd_cpu_l: DCDC_REG2 { |
| regulator-name = "vdd_cpu_l"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <750000>; |
| regulator-max-microvolt = <1350000>; |
| regulator-ramp-delay = <6001>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| vcc_ddr: DCDC_REG3 { |
| regulator-name = "vcc_ddr"; |
| regulator-always-on; |
| regulator-boot-on; |
| |
| regulator-state-mem { |
| regulator-on-in-suspend; |
| }; |
| }; |
| |
| vcc_1v8: vcc_wl: DCDC_REG4 { |
| regulator-name = "vcc_1v8"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| |
| regulator-state-mem { |
| regulator-on-in-suspend; |
| regulator-suspend-microvolt = <1800000>; |
| }; |
| }; |
| |
| /* not used */ |
| LDO_REG1 { |
| }; |
| |
| /* not used */ |
| LDO_REG2 { |
| }; |
| |
| vcc1v8_pmupll: LDO_REG3 { |
| regulator-name = "vcc1v8_pmupll"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| |
| regulator-state-mem { |
| regulator-on-in-suspend; |
| regulator-suspend-microvolt = <1800000>; |
| }; |
| }; |
| |
| vcc_sdio: LDO_REG4 { |
| regulator-name = "vcc_sdio"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3000000>; |
| |
| regulator-state-mem { |
| regulator-on-in-suspend; |
| regulator-suspend-microvolt = <3000000>; |
| }; |
| }; |
| |
| vcca3v0_codec: LDO_REG5 { |
| regulator-name = "vcca3v0_codec"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3000000>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| vcc_1v5: LDO_REG6 { |
| regulator-name = "vcc_1v5"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <1500000>; |
| regulator-max-microvolt = <1500000>; |
| |
| regulator-state-mem { |
| regulator-on-in-suspend; |
| regulator-suspend-microvolt = <1500000>; |
| }; |
| }; |
| |
| vcca1v8_codec: LDO_REG7 { |
| regulator-name = "vcca1v8_codec"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| vcc_3v0: LDO_REG8 { |
| regulator-name = "vcc_3v0"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3000000>; |
| |
| regulator-state-mem { |
| regulator-on-in-suspend; |
| regulator-suspend-microvolt = <3000000>; |
| }; |
| }; |
| |
| vcc3v3_s3: SWITCH_REG1 { |
| regulator-name = "vcc3v3_s3"; |
| regulator-always-on; |
| regulator-boot-on; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| vcc3v3_s0: SWITCH_REG2 { |
| regulator-name = "vcc3v3_s0"; |
| regulator-always-on; |
| regulator-boot-on; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| }; |
| }; |
| |
| vdd_cpu_b: regulator@40 { |
| compatible = "silergy,syr827"; |
| reg = <0x40>; |
| fcs,suspend-voltage-selector = <1>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&vsel1_gpio>; |
| regulator-name = "vdd_cpu_b"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <712500>; |
| regulator-max-microvolt = <1500000>; |
| regulator-ramp-delay = <1000>; |
| vin-supply = <&vcc_1v8>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| vdd_gpu: regulator@41 { |
| compatible = "silergy,syr828"; |
| reg = <0x41>; |
| fcs,suspend-voltage-selector = <1>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&vsel2_gpio>; |
| regulator-name = "vdd_gpu"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <712500>; |
| regulator-max-microvolt = <1500000>; |
| regulator-ramp-delay = <1000>; |
| vin-supply = <&vcc_1v8>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| }; |
| |
| &i2c1 { |
| clock-frequency = <100000>; |
| i2c-scl-falling-time-ns = <4>; |
| i2c-scl-rising-time-ns = <168>; |
| status = "okay"; |
| |
| es8316: es8316@11 { |
| compatible = "everest,es8316"; |
| reg = <0x11>; |
| clocks = <&cru SCLK_I2S_8CH_OUT>; |
| clock-names = "mclk"; |
| #sound-dai-cells = <0>; |
| }; |
| }; |
| |
| &i2c3 { |
| i2c-scl-falling-time-ns = <15>; |
| i2c-scl-rising-time-ns = <450>; |
| status = "okay"; |
| }; |
| |
| &i2c4 { |
| i2c-scl-falling-time-ns = <20>; |
| i2c-scl-rising-time-ns = <600>; |
| status = "okay"; |
| |
| fusb0: fusb30x@22 { |
| compatible = "fcs,fusb302"; |
| reg = <0x22>; |
| interrupt-parent = <&gpio1>; |
| interrupts = <RK_PA2 IRQ_TYPE_LEVEL_LOW>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&fusb0_int_gpio>; |
| vbus-supply = <&vbus_typec>; |
| |
| connector { |
| compatible = "usb-c-connector"; |
| data-role = "host"; |
| label = "USB-C"; |
| op-sink-microwatt = <1000000>; |
| power-role = "dual"; |
| sink-pdos = |
| <PDO_FIXED(5000, 2500, PDO_FIXED_USB_COMM)>; |
| source-pdos = |
| <PDO_FIXED(5000, 1400, PDO_FIXED_USB_COMM)>; |
| try-power-role = "sink"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| |
| usbc_hs: endpoint { |
| remote-endpoint = |
| <&u2phy0_typec_hs>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| |
| usbc_ss: endpoint { |
| remote-endpoint = |
| <&tcphy0_typec_ss>; |
| }; |
| }; |
| |
| port@2 { |
| reg = <2>; |
| |
| usbc_dp: endpoint { |
| remote-endpoint = |
| <&tcphy0_typec_dp>; |
| }; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| &i2s1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2s_8ch_mclk_gpio>, <&i2s1_2ch_bus>; |
| rockchip,capture-channels = <8>; |
| rockchip,playback-channels = <8>; |
| status = "okay"; |
| }; |
| |
| &io_domains { |
| audio-supply = <&vcc_3v0>; |
| gpio1830-supply = <&vcc_3v0>; |
| sdmmc-supply = <&vcc_sdio>; |
| status = "okay"; |
| }; |
| |
| &pcie_phy { |
| status = "okay"; |
| }; |
| |
| &pcie0 { |
| bus-scan-delay-ms = <1000>; |
| ep-gpios = <&gpio2 RK_PD4 GPIO_ACTIVE_HIGH>; |
| max-link-speed = <2>; |
| num-lanes = <4>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pcie_clkreqn_cpm>; |
| vpcie0v9-supply = <&vcca0v9_s3>; |
| vpcie1v8-supply = <&vcca1v8_s3>; |
| vpcie3v3-supply = <&vcc3v3_ssd>; |
| status = "okay"; |
| }; |
| |
| &pinctrl { |
| buttons { |
| pwrbtn_gpio: pwrbtn-gpio { |
| rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>; |
| }; |
| |
| lidbtn_gpio: lidbtn-gpio { |
| rockchip,pins = <1 RK_PA1 RK_FUNC_GPIO &pcfg_pull_up>; |
| }; |
| }; |
| |
| dc-charger { |
| dc_det_gpio: dc-det-gpio { |
| rockchip,pins = <4 RK_PD0 RK_FUNC_GPIO &pcfg_pull_up>; |
| }; |
| }; |
| |
| es8316 { |
| hp_det_gpio: hp-det-gpio { |
| rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_up>; |
| }; |
| }; |
| |
| fusb302x { |
| fusb0_int_gpio: fusb0-int-gpio { |
| rockchip,pins = <1 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up>; |
| }; |
| }; |
| |
| i2s1 { |
| i2s_8ch_mclk_gpio: i2s-8ch-mclk-gpio { |
| rockchip,pins = <4 RK_PA0 1 &pcfg_pull_none>; |
| }; |
| }; |
| |
| lcd-panel { |
| lcdvcc_en_gpio: lcdvcc-en-gpio { |
| rockchip,pins = <1 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>; |
| }; |
| |
| panel_en_gpio: panel-en-gpio { |
| rockchip,pins = <1 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>; |
| }; |
| |
| lcd_panel_reset_gpio: lcd-panel-reset-gpio { |
| rockchip,pins = <4 RK_PD6 RK_FUNC_GPIO &pcfg_pull_up>; |
| }; |
| }; |
| |
| leds { |
| pwr_led_pin: pwr-led-pin { |
| rockchip,pins = <0 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>; |
| }; |
| |
| slp_led_pin: slp-led-pin { |
| rockchip,pins = <0 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>; |
| }; |
| }; |
| |
| pmic { |
| pmic_int_l_gpio: pmic-int-l-gpio { |
| rockchip,pins = <3 RK_PB2 RK_FUNC_GPIO &pcfg_pull_up>; |
| }; |
| |
| vsel1_gpio: vsel1-gpio { |
| rockchip,pins = <1 RK_PC1 RK_FUNC_GPIO &pcfg_pull_down>; |
| }; |
| |
| vsel2_gpio: vsel2-gpio { |
| rockchip,pins = <1 RK_PB6 RK_FUNC_GPIO &pcfg_pull_down>; |
| }; |
| }; |
| |
| sdcard { |
| sdmmc0_pwr_h_gpio: sdmmc0-pwr-h-gpio { |
| rockchip,pins = <0 RK_PA1 RK_FUNC_GPIO &pcfg_pull_none>; |
| }; |
| |
| }; |
| |
| sdio-pwrseq { |
| wifi_enable_h_gpio: wifi-enable-h-gpio { |
| rockchip,pins = <0 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>; |
| }; |
| }; |
| |
| usb-typec { |
| vcc5v0_typec0_en_gpio: vcc5v0-typec0-en-gpio { |
| rockchip,pins = <1 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>; |
| }; |
| }; |
| |
| usb2 { |
| pwr_5v_gpio: pwr-5v-gpio { |
| rockchip,pins = <1 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>; |
| }; |
| |
| vcc5v0_host_en_gpio: vcc5v0-host-en-gpio { |
| rockchip,pins = <4 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>; |
| }; |
| }; |
| |
| wireless-bluetooth { |
| bt_wake_gpio: bt-wake-gpio { |
| rockchip,pins = <2 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>; |
| }; |
| |
| bt_host_wake_gpio: bt-host-wake-gpio { |
| rockchip,pins = <0 RK_PA4 RK_FUNC_GPIO &pcfg_pull_none>; |
| }; |
| |
| bt_reset_gpio: bt-reset-gpio { |
| rockchip,pins = <0 RK_PB1 RK_FUNC_GPIO &pcfg_pull_none>; |
| }; |
| }; |
| }; |
| |
| &pmu_io_domains { |
| pmu1830-supply = <&vcc_3v0>; |
| status = "okay"; |
| }; |
| |
| &pwm0 { |
| status = "okay"; |
| }; |
| |
| &pwm2 { |
| status = "okay"; |
| }; |
| |
| &saradc { |
| vref-supply = <&vcca1v8_s3>; |
| status = "okay"; |
| }; |
| |
| &sdmmc { |
| bus-width = <4>; |
| cap-mmc-highspeed; |
| cap-sd-highspeed; |
| cd-gpios = <&gpio0 RK_PA7 GPIO_ACTIVE_LOW>; |
| disable-wp; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_bus4>; |
| sd-uhs-sdr104; |
| vmmc-supply = <&vcc3v0_sd>; |
| vqmmc-supply = <&vcc_sdio>; |
| status = "okay"; |
| }; |
| |
| &sdio0 { |
| bus-width = <4>; |
| cap-sd-highspeed; |
| cap-sdio-irq; |
| keep-power-in-suspend; |
| mmc-pwrseq = <&sdio_pwrseq>; |
| non-removable; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&sdio0_bus4 &sdio0_cmd &sdio0_clk>; |
| sd-uhs-sdr104; |
| status = "okay"; |
| }; |
| |
| &sdhci { |
| bus-width = <8>; |
| mmc-hs200-1_8v; |
| non-removable; |
| status = "okay"; |
| }; |
| |
| &spi1 { |
| max-freq = <10000000>; |
| status = "okay"; |
| |
| spiflash: flash@0 { |
| compatible = "jedec,spi-nor"; |
| reg = <0>; |
| m25p,fast-read; |
| spi-max-frequency = <10000000>; |
| }; |
| }; |
| |
| &tcphy0 { |
| status = "okay"; |
| }; |
| |
| &tcphy0_dp { |
| port { |
| tcphy0_typec_dp: endpoint { |
| remote-endpoint = <&usbc_dp>; |
| }; |
| }; |
| }; |
| |
| &tcphy0_usb3 { |
| port { |
| tcphy0_typec_ss: endpoint { |
| remote-endpoint = <&usbc_ss>; |
| }; |
| }; |
| }; |
| |
| &tcphy1 { |
| status = "okay"; |
| }; |
| |
| &tsadc { |
| /* tshut mode 0:CRU 1:GPIO */ |
| rockchip,hw-tshut-mode = <1>; |
| /* tshut polarity 0:LOW 1:HIGH */ |
| rockchip,hw-tshut-polarity = <1>; |
| status = "okay"; |
| }; |
| |
| &u2phy0 { |
| status = "okay"; |
| |
| u2phy0_otg: otg-port { |
| status = "okay"; |
| }; |
| |
| u2phy0_host: host-port { |
| phy-supply = <&vcc5v0_otg>; |
| status = "okay"; |
| }; |
| |
| port { |
| u2phy0_typec_hs: endpoint { |
| remote-endpoint = <&usbc_hs>; |
| }; |
| }; |
| }; |
| |
| &u2phy1 { |
| status = "okay"; |
| |
| u2phy1_otg: otg-port { |
| status = "okay"; |
| }; |
| |
| u2phy1_host: host-port { |
| phy-supply = <&vcc5v0_otg>; |
| status = "okay"; |
| }; |
| }; |
| |
| &uart0 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart0_xfer &uart0_cts &uart0_rts>; |
| uart-has-rtscts; |
| status = "okay"; |
| |
| bluetooth { |
| compatible = "brcm,bcm4345c5"; |
| clocks = <&rk808 1>; |
| clock-names = "lpo"; |
| device-wakeup-gpios = <&gpio2 RK_PD3 GPIO_ACTIVE_HIGH>; |
| host-wakeup-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_HIGH>; |
| max-speed = <1500000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&bt_host_wake_gpio &bt_wake_gpio &bt_reset_gpio>; |
| shutdown-gpios = <&gpio0 RK_PB1 GPIO_ACTIVE_HIGH>; |
| vbat-supply = <&wifi_bat>; |
| vddio-supply = <&vcc_wl>; |
| }; |
| }; |
| |
| &uart2 { |
| status = "okay"; |
| }; |
| |
| &usb_host0_ehci { |
| status = "okay"; |
| }; |
| |
| &usb_host0_ohci { |
| status = "okay"; |
| }; |
| |
| &usb_host1_ehci { |
| status = "okay"; |
| }; |
| |
| &usb_host1_ohci { |
| status = "okay"; |
| }; |
| |
| &usbdrd3_0 { |
| status = "okay"; |
| }; |
| |
| &usbdrd_dwc3_0 { |
| dr_mode = "host"; |
| status = "okay"; |
| }; |
| |
| &usbdrd3_1 { |
| status = "okay"; |
| }; |
| |
| &usbdrd_dwc3_1 { |
| dr_mode = "host"; |
| status = "okay"; |
| }; |
| |
| &vopb { |
| status = "okay"; |
| }; |
| |
| &vopb_mmu { |
| status = "okay"; |
| }; |
| |
| &vopl { |
| status = "okay"; |
| }; |
| |
| &vopl_mmu { |
| status = "okay"; |
| }; |
