| Devicetree bindings for the Axentia TSE-850 audio complex |
| |
| Required properties: |
| - compatible: "axentia,tse850-pcm5142" |
| - axentia,cpu-dai: The phandle of the cpu dai. |
| - axentia,audio-codec: The phandle of the PCM5142 codec. |
| - axentia,add-gpios: gpio specifier that controls the mixer. |
| - axentia,loop1-gpios: gpio specifier that controls loop relays on channel 1. |
| - axentia,loop2-gpios: gpio specifier that controls loop relays on channel 2. |
| - axentia,ana-supply: Regulator that supplies the output amplifier. Must |
| support voltages in the 2V - 20V range, in 1V steps. |
| |
| The schematics explaining the gpios are as follows: |
| |
| loop1 relays |
| IN1 +---o +------------+ o---+ OUT1 |
| \ / |
| + + |
| | / | |
| +--o +--. | |
| | add | | |
| | V | |
| | .---. | |
| DAC +----------->|Sum|---+ |
| | '---' | |
| | | |
| + + |
| |
| IN2 +---o--+------------+--o---+ OUT2 |
| loop2 relays |
| |
| The 'loop1' gpio pin controls two relays, which are either in loop position, |
| meaning that input and output are directly connected, or they are in mixer |
| position, meaning that the signal is passed through the 'Sum' mixer. Similarly |
| for 'loop2'. |
| |
| In the above, the 'loop1' relays are inactive, thus feeding IN1 to the mixer |
| (if 'add' is active) and feeding the mixer output to OUT1. The 'loop2' relays |
| are active, short-cutting the TSE-850 from channel 2. IN1, IN2, OUT1 and OUT2 |
| are TSE-850 connectors and DAC is the PCB name of the (filtered) output from |
| the PCM5142 codec. |
| |
| Example: |
| |
| &ssc0 { |
| #sound-dai-cells = <0>; |
| |
| }; |
| |
| &i2c { |
| codec: pcm5142@4c { |
| compatible = "ti,pcm5142"; |
| |
| reg = <0x4c>; |
| |
| AVDD-supply = <®_3v3>; |
| DVDD-supply = <®_3v3>; |
| CPVDD-supply = <®_3v3>; |
| |
| clocks = <&sck>; |
| |
| pll-in = <3>; |
| pll-out = <6>; |
| }; |
| }; |
| |
| ana: ana-reg { |
| compatible = "pwm-regulator"; |
| |
| regulator-name = "ANA"; |
| |
| pwms = <&pwm0 2 1000 PWM_POLARITY_INVERTED>; |
| pwm-dutycycle-unit = <1000>; |
| pwm-dutycycle-range = <100 1000>; |
| |
| regulator-min-microvolt = <2000000>; |
| regulator-max-microvolt = <20000000>; |
| regulator-ramp-delay = <1000>; |
| }; |
| |
| sound { |
| compatible = "axentia,tse850-pcm5142"; |
| |
| axentia,cpu-dai = <&ssc0>; |
| axentia,audio-codec = <&codec>; |
| |
| axentia,add-gpios = <&pioA 8 GPIO_ACTIVE_LOW>; |
| axentia,loop1-gpios = <&pioA 10 GPIO_ACTIVE_LOW>; |
| axentia,loop2-gpios = <&pioA 11 GPIO_ACTIVE_LOW>; |
| |
| axentia,ana-supply = <&ana>; |
| }; |