| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * Common clock framework driver for the Versaclock7 family of timing devices. |
| * |
| * Copyright (c) 2022 Renesas Electronics Corporation |
| */ |
| |
| #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt |
| |
| #include <linux/bitfield.h> |
| #include <linux/clk.h> |
| #include <linux/clk-provider.h> |
| #include <linux/i2c.h> |
| #include <linux/math64.h> |
| #include <linux/module.h> |
| #include <linux/of.h> |
| #include <linux/of_platform.h> |
| #include <linux/regmap.h> |
| #include <linux/swab.h> |
| |
| /* |
| * 16-bit register address: the lower 8 bits of the register address come |
| * from the offset addr byte and the upper 8 bits come from the page register. |
| */ |
| #define VC7_PAGE_ADDR 0xFD |
| #define VC7_PAGE_WINDOW 256 |
| #define VC7_MAX_REG 0x364 |
| |
| /* Maximum number of banks supported by VC7 */ |
| #define VC7_NUM_BANKS 7 |
| |
| /* Maximum number of FODs supported by VC7 */ |
| #define VC7_NUM_FOD 3 |
| |
| /* Maximum number of IODs supported by VC7 */ |
| #define VC7_NUM_IOD 4 |
| |
| /* Maximum number of outputs supported by VC7 */ |
| #define VC7_NUM_OUT 12 |
| |
| /* VCO valid range is 9.5 GHz to 10.7 GHz */ |
| #define VC7_APLL_VCO_MIN 9500000000UL |
| #define VC7_APLL_VCO_MAX 10700000000UL |
| |
| /* APLL denominator is fixed at 2^27 */ |
| #define VC7_APLL_DENOMINATOR_BITS 27 |
| |
| /* FOD 1st stage denominator is fixed 2^34 */ |
| #define VC7_FOD_DENOMINATOR_BITS 34 |
| |
| /* IOD can operate between 1kHz and 650MHz */ |
| #define VC7_IOD_RATE_MIN 1000UL |
| #define VC7_IOD_RATE_MAX 650000000UL |
| #define VC7_IOD_MIN_DIVISOR 14 |
| #define VC7_IOD_MAX_DIVISOR 0x1ffffff /* 25-bit */ |
| |
| #define VC7_FOD_RATE_MIN 1000UL |
| #define VC7_FOD_RATE_MAX 650000000UL |
| #define VC7_FOD_1ST_STAGE_RATE_MIN 33000000UL /* 33 MHz */ |
| #define VC7_FOD_1ST_STAGE_RATE_MAX 650000000UL /* 650 MHz */ |
| #define VC7_FOD_1ST_INT_MAX 324 |
| #define VC7_FOD_2ND_INT_MIN 2 |
| #define VC7_FOD_2ND_INT_MAX 0x1ffff /* 17-bit */ |
| |
| /* VC7 Registers */ |
| |
| #define VC7_REG_XO_CNFG 0x2C |
| #define VC7_REG_XO_CNFG_COUNT 4 |
| #define VC7_REG_XO_IB_H_DIV_SHIFT 24 |
| #define VC7_REG_XO_IB_H_DIV_MASK GENMASK(28, VC7_REG_XO_IB_H_DIV_SHIFT) |
| |
| #define VC7_REG_APLL_FB_DIV_FRAC 0x120 |
| #define VC7_REG_APLL_FB_DIV_FRAC_COUNT 4 |
| #define VC7_REG_APLL_FB_DIV_FRAC_MASK GENMASK(26, 0) |
| |
| #define VC7_REG_APLL_FB_DIV_INT 0x124 |
| #define VC7_REG_APLL_FB_DIV_INT_COUNT 2 |
| #define VC7_REG_APLL_FB_DIV_INT_MASK GENMASK(9, 0) |
| |
| #define VC7_REG_APLL_CNFG 0x127 |
| #define VC7_REG_APLL_EN_DOUBLER BIT(0) |
| |
| #define VC7_REG_OUT_BANK_CNFG(idx) (0x280 + (0x4 * (idx))) |
| #define VC7_REG_OUTPUT_BANK_SRC_MASK GENMASK(2, 0) |
| |
| #define VC7_REG_FOD_INT_CNFG(idx) (0x1E0 + (0x10 * (idx))) |
| #define VC7_REG_FOD_INT_CNFG_COUNT 8 |
| #define VC7_REG_FOD_1ST_INT_MASK GENMASK(8, 0) |
| #define VC7_REG_FOD_2ND_INT_SHIFT 9 |
| #define VC7_REG_FOD_2ND_INT_MASK GENMASK(25, VC7_REG_FOD_2ND_INT_SHIFT) |
| #define VC7_REG_FOD_FRAC_SHIFT 26 |
| #define VC7_REG_FOD_FRAC_MASK GENMASK_ULL(59, VC7_REG_FOD_FRAC_SHIFT) |
| |
| #define VC7_REG_IOD_INT_CNFG(idx) (0x1C0 + (0x8 * (idx))) |
| #define VC7_REG_IOD_INT_CNFG_COUNT 4 |
| #define VC7_REG_IOD_INT_MASK GENMASK(24, 0) |
| |
| #define VC7_REG_ODRV_EN(idx) (0x240 + (0x4 * (idx))) |
| #define VC7_REG_OUT_DIS BIT(0) |
| |
| struct vc7_driver_data; |
| static const struct regmap_config vc7_regmap_config; |
| |
| /* Supported Renesas VC7 models */ |
| enum vc7_model { |
| VC7_RC21008A, |
| }; |
| |
| struct vc7_chip_info { |
| const enum vc7_model model; |
| const unsigned int banks[VC7_NUM_BANKS]; |
| const unsigned int num_banks; |
| const unsigned int outputs[VC7_NUM_OUT]; |
| const unsigned int num_outputs; |
| }; |
| |
| /* |
| * Changing the APLL frequency is currently not supported. |
| * The APLL will consist of an opaque block between the XO and FOD/IODs and |
| * its frequency will be computed based on the current state of the device. |
| */ |
| struct vc7_apll_data { |
| struct clk *clk; |
| struct vc7_driver_data *vc7; |
| u8 xo_ib_h_div; |
| u8 en_doubler; |
| u16 apll_fb_div_int; |
| u32 apll_fb_div_frac; |
| }; |
| |
| struct vc7_fod_data { |
| struct clk_hw hw; |
| struct vc7_driver_data *vc7; |
| unsigned int num; |
| u32 fod_1st_int; |
| u32 fod_2nd_int; |
| u64 fod_frac; |
| }; |
| |
| struct vc7_iod_data { |
| struct clk_hw hw; |
| struct vc7_driver_data *vc7; |
| unsigned int num; |
| u32 iod_int; |
| }; |
| |
| struct vc7_out_data { |
| struct clk_hw hw; |
| struct vc7_driver_data *vc7; |
| unsigned int num; |
| unsigned int out_dis; |
| }; |
| |
| struct vc7_driver_data { |
| struct i2c_client *client; |
| struct regmap *regmap; |
| const struct vc7_chip_info *chip_info; |
| |
| struct clk *pin_xin; |
| struct vc7_apll_data clk_apll; |
| struct vc7_fod_data clk_fod[VC7_NUM_FOD]; |
| struct vc7_iod_data clk_iod[VC7_NUM_IOD]; |
| struct vc7_out_data clk_out[VC7_NUM_OUT]; |
| }; |
| |
| struct vc7_bank_src_map { |
| enum vc7_bank_src_type { |
| VC7_FOD, |
| VC7_IOD, |
| } type; |
| union _divider { |
| struct vc7_iod_data *iod; |
| struct vc7_fod_data *fod; |
| } src; |
| }; |
| |
| static struct clk_hw *vc7_of_clk_get(struct of_phandle_args *clkspec, |
| void *data) |
| { |
| struct vc7_driver_data *vc7 = data; |
| unsigned int idx = clkspec->args[0]; |
| |
| if (idx >= vc7->chip_info->num_outputs) |
| return ERR_PTR(-EINVAL); |
| |
| return &vc7->clk_out[idx].hw; |
| } |
| |
| static const unsigned int RC21008A_index_to_output_mapping[] = { |
| 1, 2, 3, 6, 7, 8, 10, 11 |
| }; |
| |
| static int vc7_map_index_to_output(const enum vc7_model model, const unsigned int i) |
| { |
| switch (model) { |
| case VC7_RC21008A: |
| return RC21008A_index_to_output_mapping[i]; |
| default: |
| return i; |
| } |
| } |
| |
| /* bank to output mapping, same across all variants */ |
| static const unsigned int output_bank_mapping[] = { |
| 0, /* Output 0 */ |
| 1, /* Output 1 */ |
| 2, /* Output 2 */ |
| 2, /* Output 3 */ |
| 3, /* Output 4 */ |
| 3, /* Output 5 */ |
| 3, /* Output 6 */ |
| 3, /* Output 7 */ |
| 4, /* Output 8 */ |
| 4, /* Output 9 */ |
| 5, /* Output 10 */ |
| 6 /* Output 11 */ |
| }; |
| |
| /** |
| * vc7_64_mul_64_to_128() - Multiply two u64 and return an unsigned 128-bit integer |
| * as an upper and lower part. |
| * |
| * @left: The left argument. |
| * @right: The right argument. |
| * @hi: The upper 64-bits of the 128-bit product. |
| * @lo: The lower 64-bits of the 128-bit product. |
| * |
| * From mul_64_64 in crypto/ecc.c:350 in the linux kernel, accessed in v5.17.2. |
| */ |
| static void vc7_64_mul_64_to_128(u64 left, u64 right, u64 *hi, u64 *lo) |
| { |
| u64 a0 = left & 0xffffffffull; |
| u64 a1 = left >> 32; |
| u64 b0 = right & 0xffffffffull; |
| u64 b1 = right >> 32; |
| u64 m0 = a0 * b0; |
| u64 m1 = a0 * b1; |
| u64 m2 = a1 * b0; |
| u64 m3 = a1 * b1; |
| |
| m2 += (m0 >> 32); |
| m2 += m1; |
| |
| /* Overflow */ |
| if (m2 < m1) |
| m3 += 0x100000000ull; |
| |
| *lo = (m0 & 0xffffffffull) | (m2 << 32); |
| *hi = m3 + (m2 >> 32); |
| } |
| |
| /** |
| * vc7_128_div_64_to_64() - Divides a 128-bit uint by a 64-bit divisor, return a 64-bit quotient. |
| * |
| * @numhi: The uppper 64-bits of the dividend. |
| * @numlo: The lower 64-bits of the dividend. |
| * @den: The denominator (divisor). |
| * @r: The remainder, pass NULL if the remainder is not needed. |
| * |
| * Originally from libdivide, modified to use kernel u64/u32 types. |
| * |
| * See https://github.com/ridiculousfish/libdivide/blob/master/libdivide.h#L471. |
| * |
| * Return: The 64-bit quotient of the division. |
| * |
| * In case of overflow of division by zero, max(u64) is returned. |
| */ |
| static u64 vc7_128_div_64_to_64(u64 numhi, u64 numlo, u64 den, u64 *r) |
| { |
| /* |
| * We work in base 2**32. |
| * A uint32 holds a single digit. A uint64 holds two digits. |
| * Our numerator is conceptually [num3, num2, num1, num0]. |
| * Our denominator is [den1, den0]. |
| */ |
| const u64 b = ((u64)1 << 32); |
| |
| /* The high and low digits of our computed quotient. */ |
| u32 q1, q0; |
| |
| /* The normalization shift factor */ |
| int shift; |
| |
| /* |
| * The high and low digits of our denominator (after normalizing). |
| * Also the low 2 digits of our numerator (after normalizing). |
| */ |
| u32 den1, den0, num1, num0; |
| |
| /* A partial remainder; */ |
| u64 rem; |
| |
| /* |
| * The estimated quotient, and its corresponding remainder (unrelated |
| * to true remainder). |
| */ |
| u64 qhat, rhat; |
| |
| /* Variables used to correct the estimated quotient. */ |
| u64 c1, c2; |
| |
| /* Check for overflow and divide by 0. */ |
| if (numhi >= den) { |
| if (r) |
| *r = ~0ull; |
| return ~0ull; |
| } |
| |
| /* |
| * Determine the normalization factor. We multiply den by this, so that |
| * its leading digit is at least half b. In binary this means just |
| * shifting left by the number of leading zeros, so that there's a 1 in |
| * the MSB. |
| * |
| * We also shift numer by the same amount. This cannot overflow because |
| * numhi < den. The expression (-shift & 63) is the same as (64 - |
| * shift), except it avoids the UB of shifting by 64. The funny bitwise |
| * 'and' ensures that numlo does not get shifted into numhi if shift is |
| * 0. clang 11 has an x86 codegen bug here: see LLVM bug 50118. The |
| * sequence below avoids it. |
| */ |
| shift = __builtin_clzll(den); |
| den <<= shift; |
| numhi <<= shift; |
| numhi |= (numlo >> (-shift & 63)) & (-(s64)shift >> 63); |
| numlo <<= shift; |
| |
| /* |
| * Extract the low digits of the numerator and both digits of the |
| * denominator. |
| */ |
| num1 = (u32)(numlo >> 32); |
| num0 = (u32)(numlo & 0xFFFFFFFFu); |
| den1 = (u32)(den >> 32); |
| den0 = (u32)(den & 0xFFFFFFFFu); |
| |
| /* |
| * We wish to compute q1 = [n3 n2 n1] / [d1 d0]. |
| * Estimate q1 as [n3 n2] / [d1], and then correct it. |
| * Note while qhat may be 2 digits, q1 is always 1 digit. |
| */ |
| qhat = div64_u64_rem(numhi, den1, &rhat); |
| c1 = qhat * den0; |
| c2 = rhat * b + num1; |
| if (c1 > c2) |
| qhat -= (c1 - c2 > den) ? 2 : 1; |
| q1 = (u32)qhat; |
| |
| /* Compute the true (partial) remainder. */ |
| rem = numhi * b + num1 - q1 * den; |
| |
| /* |
| * We wish to compute q0 = [rem1 rem0 n0] / [d1 d0]. |
| * Estimate q0 as [rem1 rem0] / [d1] and correct it. |
| */ |
| qhat = div64_u64_rem(rem, den1, &rhat); |
| c1 = qhat * den0; |
| c2 = rhat * b + num0; |
| if (c1 > c2) |
| qhat -= (c1 - c2 > den) ? 2 : 1; |
| q0 = (u32)qhat; |
| |
| /* Return remainder if requested. */ |
| if (r) |
| *r = (rem * b + num0 - q0 * den) >> shift; |
| return ((u64)q1 << 32) | q0; |
| } |
| |
| static int vc7_get_bank_clk(struct vc7_driver_data *vc7, |
| unsigned int bank_idx, |
| unsigned int output_bank_src, |
| struct vc7_bank_src_map *map) |
| { |
| /* Mapping from Table 38 in datasheet */ |
| if (bank_idx == 0 || bank_idx == 1) { |
| switch (output_bank_src) { |
| case 0: |
| map->type = VC7_IOD, |
| map->src.iod = &vc7->clk_iod[0]; |
| return 0; |
| case 1: |
| map->type = VC7_IOD, |
| map->src.iod = &vc7->clk_iod[1]; |
| return 0; |
| case 4: |
| map->type = VC7_FOD, |
| map->src.fod = &vc7->clk_fod[0]; |
| return 0; |
| case 5: |
| map->type = VC7_FOD, |
| map->src.fod = &vc7->clk_fod[1]; |
| return 0; |
| default: |
| break; |
| } |
| } else if (bank_idx == 2) { |
| switch (output_bank_src) { |
| case 1: |
| map->type = VC7_IOD, |
| map->src.iod = &vc7->clk_iod[1]; |
| return 0; |
| case 4: |
| map->type = VC7_FOD, |
| map->src.fod = &vc7->clk_fod[0]; |
| return 0; |
| case 5: |
| map->type = VC7_FOD, |
| map->src.fod = &vc7->clk_fod[1]; |
| return 0; |
| default: |
| break; |
| } |
| } else if (bank_idx == 3) { |
| switch (output_bank_src) { |
| case 4: |
| map->type = VC7_FOD, |
| map->src.fod = &vc7->clk_fod[0]; |
| return 0; |
| case 5: |
| map->type = VC7_FOD, |
| map->src.fod = &vc7->clk_fod[1]; |
| return 0; |
| case 6: |
| map->type = VC7_FOD, |
| map->src.fod = &vc7->clk_fod[2]; |
| return 0; |
| default: |
| break; |
| } |
| } else if (bank_idx == 4) { |
| switch (output_bank_src) { |
| case 0: |
| /* CLKIN1 not supported in this driver */ |
| break; |
| case 2: |
| map->type = VC7_IOD, |
| map->src.iod = &vc7->clk_iod[2]; |
| return 0; |
| case 5: |
| map->type = VC7_FOD, |
| map->src.fod = &vc7->clk_fod[1]; |
| return 0; |
| case 6: |
| map->type = VC7_FOD, |
| map->src.fod = &vc7->clk_fod[2]; |
| return 0; |
| case 7: |
| /* CLKIN0 not supported in this driver */ |
| break; |
| default: |
| break; |
| } |
| } else if (bank_idx == 5) { |
| switch (output_bank_src) { |
| case 0: |
| /* CLKIN1 not supported in this driver */ |
| break; |
| case 1: |
| /* XIN_REFIN not supported in this driver */ |
| break; |
| case 2: |
| map->type = VC7_IOD, |
| map->src.iod = &vc7->clk_iod[2]; |
| return 0; |
| case 3: |
| map->type = VC7_IOD, |
| map->src.iod = &vc7->clk_iod[3]; |
| return 0; |
| case 5: |
| map->type = VC7_FOD, |
| map->src.fod = &vc7->clk_fod[1]; |
| return 0; |
| case 6: |
| map->type = VC7_FOD, |
| map->src.fod = &vc7->clk_fod[2]; |
| return 0; |
| case 7: |
| /* CLKIN0 not supported in this driver */ |
| break; |
| default: |
| break; |
| } |
| } else if (bank_idx == 6) { |
| switch (output_bank_src) { |
| case 0: |
| /* CLKIN1 not supported in this driver */ |
| break; |
| case 2: |
| map->type = VC7_IOD, |
| map->src.iod = &vc7->clk_iod[2]; |
| return 0; |
| case 3: |
| map->type = VC7_IOD, |
| map->src.iod = &vc7->clk_iod[3]; |
| return 0; |
| case 5: |
| map->type = VC7_FOD, |
| map->src.fod = &vc7->clk_fod[1]; |
| return 0; |
| case 6: |
| map->type = VC7_FOD, |
| map->src.fod = &vc7->clk_fod[2]; |
| return 0; |
| case 7: |
| /* CLKIN0 not supported in this driver */ |
| break; |
| default: |
| break; |
| } |
| } |
| |
| pr_warn("bank_src%d = %d is not supported\n", bank_idx, output_bank_src); |
| return -1; |
| } |
| |
| static int vc7_read_apll(struct vc7_driver_data *vc7) |
| { |
| int err; |
| u32 val32; |
| u16 val16; |
| |
| err = regmap_bulk_read(vc7->regmap, |
| VC7_REG_XO_CNFG, |
| (u32 *)&val32, |
| VC7_REG_XO_CNFG_COUNT); |
| if (err) { |
| dev_err(&vc7->client->dev, "failed to read XO_CNFG\n"); |
| return err; |
| } |
| |
| vc7->clk_apll.xo_ib_h_div = (val32 & VC7_REG_XO_IB_H_DIV_MASK) |
| >> VC7_REG_XO_IB_H_DIV_SHIFT; |
| |
| err = regmap_read(vc7->regmap, |
| VC7_REG_APLL_CNFG, |
| &val32); |
| if (err) { |
| dev_err(&vc7->client->dev, "failed to read APLL_CNFG\n"); |
| return err; |
| } |
| |
| vc7->clk_apll.en_doubler = val32 & VC7_REG_APLL_EN_DOUBLER; |
| |
| err = regmap_bulk_read(vc7->regmap, |
| VC7_REG_APLL_FB_DIV_FRAC, |
| (u32 *)&val32, |
| VC7_REG_APLL_FB_DIV_FRAC_COUNT); |
| if (err) { |
| dev_err(&vc7->client->dev, "failed to read APLL_FB_DIV_FRAC\n"); |
| return err; |
| } |
| |
| vc7->clk_apll.apll_fb_div_frac = val32 & VC7_REG_APLL_FB_DIV_FRAC_MASK; |
| |
| err = regmap_bulk_read(vc7->regmap, |
| VC7_REG_APLL_FB_DIV_INT, |
| (u16 *)&val16, |
| VC7_REG_APLL_FB_DIV_INT_COUNT); |
| if (err) { |
| dev_err(&vc7->client->dev, "failed to read APLL_FB_DIV_INT\n"); |
| return err; |
| } |
| |
| vc7->clk_apll.apll_fb_div_int = val16 & VC7_REG_APLL_FB_DIV_INT_MASK; |
| |
| return 0; |
| } |
| |
| static int vc7_read_fod(struct vc7_driver_data *vc7, unsigned int idx) |
| { |
| int err; |
| u64 val; |
| |
| err = regmap_bulk_read(vc7->regmap, |
| VC7_REG_FOD_INT_CNFG(idx), |
| (u64 *)&val, |
| VC7_REG_FOD_INT_CNFG_COUNT); |
| if (err) { |
| dev_err(&vc7->client->dev, "failed to read FOD%d\n", idx); |
| return err; |
| } |
| |
| vc7->clk_fod[idx].fod_1st_int = (val & VC7_REG_FOD_1ST_INT_MASK); |
| vc7->clk_fod[idx].fod_2nd_int = |
| (val & VC7_REG_FOD_2ND_INT_MASK) >> VC7_REG_FOD_2ND_INT_SHIFT; |
| vc7->clk_fod[idx].fod_frac = (val & VC7_REG_FOD_FRAC_MASK) |
| >> VC7_REG_FOD_FRAC_SHIFT; |
| |
| return 0; |
| } |
| |
| static int vc7_write_fod(struct vc7_driver_data *vc7, unsigned int idx) |
| { |
| int err; |
| u64 val; |
| |
| /* |
| * FOD dividers are part of an atomic group where fod_1st_int, |
| * fod_2nd_int, and fod_frac must be written together. The new divider |
| * is applied when the MSB of fod_frac is written. |
| */ |
| |
| err = regmap_bulk_read(vc7->regmap, |
| VC7_REG_FOD_INT_CNFG(idx), |
| (u64 *)&val, |
| VC7_REG_FOD_INT_CNFG_COUNT); |
| if (err) { |
| dev_err(&vc7->client->dev, "failed to read FOD%d\n", idx); |
| return err; |
| } |
| |
| val = u64_replace_bits(val, |
| vc7->clk_fod[idx].fod_1st_int, |
| VC7_REG_FOD_1ST_INT_MASK); |
| val = u64_replace_bits(val, |
| vc7->clk_fod[idx].fod_2nd_int, |
| VC7_REG_FOD_2ND_INT_MASK); |
| val = u64_replace_bits(val, |
| vc7->clk_fod[idx].fod_frac, |
| VC7_REG_FOD_FRAC_MASK); |
| |
| err = regmap_bulk_write(vc7->regmap, |
| VC7_REG_FOD_INT_CNFG(idx), |
| (u64 *)&val, |
| sizeof(u64)); |
| if (err) { |
| dev_err(&vc7->client->dev, "failed to write FOD%d\n", idx); |
| return err; |
| } |
| |
| return 0; |
| } |
| |
| static int vc7_read_iod(struct vc7_driver_data *vc7, unsigned int idx) |
| { |
| int err; |
| u32 val; |
| |
| err = regmap_bulk_read(vc7->regmap, |
| VC7_REG_IOD_INT_CNFG(idx), |
| (u32 *)&val, |
| VC7_REG_IOD_INT_CNFG_COUNT); |
| if (err) { |
| dev_err(&vc7->client->dev, "failed to read IOD%d\n", idx); |
| return err; |
| } |
| |
| vc7->clk_iod[idx].iod_int = (val & VC7_REG_IOD_INT_MASK); |
| |
| return 0; |
| } |
| |
| static int vc7_write_iod(struct vc7_driver_data *vc7, unsigned int idx) |
| { |
| int err; |
| u32 val; |
| |
| /* |
| * IOD divider field is atomic and all bits must be written. |
| * The new divider is applied when the MSB of iod_int is written. |
| */ |
| |
| err = regmap_bulk_read(vc7->regmap, |
| VC7_REG_IOD_INT_CNFG(idx), |
| (u32 *)&val, |
| VC7_REG_IOD_INT_CNFG_COUNT); |
| if (err) { |
| dev_err(&vc7->client->dev, "failed to read IOD%d\n", idx); |
| return err; |
| } |
| |
| val = u32_replace_bits(val, |
| vc7->clk_iod[idx].iod_int, |
| VC7_REG_IOD_INT_MASK); |
| |
| err = regmap_bulk_write(vc7->regmap, |
| VC7_REG_IOD_INT_CNFG(idx), |
| (u32 *)&val, |
| sizeof(u32)); |
| if (err) { |
| dev_err(&vc7->client->dev, "failed to write IOD%d\n", idx); |
| return err; |
| } |
| |
| return 0; |
| } |
| |
| static int vc7_read_output(struct vc7_driver_data *vc7, unsigned int idx) |
| { |
| int err; |
| unsigned int val, out_num; |
| |
| out_num = vc7_map_index_to_output(vc7->chip_info->model, idx); |
| err = regmap_read(vc7->regmap, |
| VC7_REG_ODRV_EN(out_num), |
| &val); |
| if (err) { |
| dev_err(&vc7->client->dev, "failed to read ODRV_EN[%d]\n", idx); |
| return err; |
| } |
| |
| vc7->clk_out[idx].out_dis = val & VC7_REG_OUT_DIS; |
| |
| return 0; |
| } |
| |
| static int vc7_write_output(struct vc7_driver_data *vc7, unsigned int idx) |
| { |
| int err; |
| unsigned int out_num; |
| |
| out_num = vc7_map_index_to_output(vc7->chip_info->model, idx); |
| err = regmap_write_bits(vc7->regmap, |
| VC7_REG_ODRV_EN(out_num), |
| VC7_REG_OUT_DIS, |
| vc7->clk_out[idx].out_dis); |
| |
| if (err) { |
| dev_err(&vc7->client->dev, "failed to write ODRV_EN[%d]\n", idx); |
| return err; |
| } |
| |
| return 0; |
| } |
| |
| static unsigned long vc7_get_apll_rate(struct vc7_driver_data *vc7) |
| { |
| int err; |
| unsigned long xtal_rate; |
| u64 refin_div, apll_rate; |
| |
| xtal_rate = clk_get_rate(vc7->pin_xin); |
| err = vc7_read_apll(vc7); |
| if (err) { |
| dev_err(&vc7->client->dev, "unable to read apll\n"); |
| return err; |
| } |
| |
| /* 0 is bypassed, 1 is reserved */ |
| if (vc7->clk_apll.xo_ib_h_div < 2) |
| refin_div = xtal_rate; |
| else |
| refin_div = div64_u64(xtal_rate, vc7->clk_apll.xo_ib_h_div); |
| |
| if (vc7->clk_apll.en_doubler) |
| refin_div *= 2; |
| |
| /* divider = int + (frac / 2^27) */ |
| apll_rate = (refin_div * vc7->clk_apll.apll_fb_div_int) + |
| ((refin_div * vc7->clk_apll.apll_fb_div_frac) >> VC7_APLL_DENOMINATOR_BITS); |
| |
| pr_debug("%s - xo_ib_h_div: %u, apll_fb_div_int: %u, apll_fb_div_frac: %u\n", |
| __func__, vc7->clk_apll.xo_ib_h_div, vc7->clk_apll.apll_fb_div_int, |
| vc7->clk_apll.apll_fb_div_frac); |
| pr_debug("%s - refin_div: %llu, apll rate: %llu\n", |
| __func__, refin_div, apll_rate); |
| |
| return apll_rate; |
| } |
| |
| static void vc7_calc_iod_divider(unsigned long rate, unsigned long parent_rate, |
| u32 *divider) |
| { |
| *divider = DIV_ROUND_UP(parent_rate, rate); |
| if (*divider < VC7_IOD_MIN_DIVISOR) |
| *divider = VC7_IOD_MIN_DIVISOR; |
| if (*divider > VC7_IOD_MAX_DIVISOR) |
| *divider = VC7_IOD_MAX_DIVISOR; |
| } |
| |
| static void vc7_calc_fod_1st_stage(unsigned long rate, unsigned long parent_rate, |
| u32 *div_int, u64 *div_frac) |
| { |
| u64 rem; |
| |
| *div_int = (u32)div64_u64_rem(parent_rate, rate, &rem); |
| *div_frac = div64_u64(rem << VC7_FOD_DENOMINATOR_BITS, rate); |
| } |
| |
| static unsigned long vc7_calc_fod_1st_stage_rate(unsigned long parent_rate, |
| u32 fod_1st_int, u64 fod_frac) |
| { |
| u64 numer, denom, hi, lo, divisor; |
| |
| numer = fod_frac; |
| denom = BIT_ULL(VC7_FOD_DENOMINATOR_BITS); |
| |
| if (fod_frac) { |
| vc7_64_mul_64_to_128(parent_rate, denom, &hi, &lo); |
| divisor = ((u64)fod_1st_int * denom) + numer; |
| return vc7_128_div_64_to_64(hi, lo, divisor, NULL); |
| } |
| |
| return div64_u64(parent_rate, fod_1st_int); |
| } |
| |
| static unsigned long vc7_calc_fod_2nd_stage_rate(unsigned long parent_rate, |
| u32 fod_1st_int, u32 fod_2nd_int, u64 fod_frac) |
| { |
| unsigned long fod_1st_stage_rate; |
| |
| fod_1st_stage_rate = vc7_calc_fod_1st_stage_rate(parent_rate, fod_1st_int, fod_frac); |
| |
| if (fod_2nd_int < 2) |
| return fod_1st_stage_rate; |
| |
| /* |
| * There is a div-by-2 preceding the 2nd stage integer divider |
| * (not shown on block diagram) so the actual 2nd stage integer |
| * divisor is 2 * N. |
| */ |
| return div64_u64(fod_1st_stage_rate >> 1, fod_2nd_int); |
| } |
| |
| static void vc7_calc_fod_divider(unsigned long rate, unsigned long parent_rate, |
| u32 *fod_1st_int, u32 *fod_2nd_int, u64 *fod_frac) |
| { |
| unsigned int allow_frac, i, best_frac_i; |
| unsigned long first_stage_rate; |
| |
| vc7_calc_fod_1st_stage(rate, parent_rate, fod_1st_int, fod_frac); |
| first_stage_rate = vc7_calc_fod_1st_stage_rate(parent_rate, *fod_1st_int, *fod_frac); |
| |
| *fod_2nd_int = 0; |
| |
| /* Do we need the second stage integer divider? */ |
| if (first_stage_rate < VC7_FOD_1ST_STAGE_RATE_MIN) { |
| allow_frac = 0; |
| best_frac_i = VC7_FOD_2ND_INT_MIN; |
| |
| for (i = VC7_FOD_2ND_INT_MIN; i <= VC7_FOD_2ND_INT_MAX; i++) { |
| /* |
| * 1) There is a div-by-2 preceding the 2nd stage integer divider |
| * (not shown on block diagram) so the actual 2nd stage integer |
| * divisor is 2 * N. |
| * 2) Attempt to find an integer solution first. This means stepping |
| * through each 2nd stage integer and recalculating the 1st stage |
| * until the 1st stage frequency is out of bounds. If no integer |
| * solution is found, use the best fractional solution. |
| */ |
| vc7_calc_fod_1st_stage(parent_rate, rate * 2 * i, fod_1st_int, fod_frac); |
| first_stage_rate = vc7_calc_fod_1st_stage_rate(parent_rate, |
| *fod_1st_int, |
| *fod_frac); |
| |
| /* Remember the first viable fractional solution */ |
| if (best_frac_i == VC7_FOD_2ND_INT_MIN && |
| first_stage_rate > VC7_FOD_1ST_STAGE_RATE_MIN) { |
| best_frac_i = i; |
| } |
| |
| /* Is the divider viable? Prefer integer solutions over fractional. */ |
| if (*fod_1st_int < VC7_FOD_1ST_INT_MAX && |
| first_stage_rate >= VC7_FOD_1ST_STAGE_RATE_MIN && |
| (allow_frac || *fod_frac == 0)) { |
| *fod_2nd_int = i; |
| break; |
| } |
| |
| /* Ran out of divisors or the 1st stage frequency is out of range */ |
| if (i >= VC7_FOD_2ND_INT_MAX || |
| first_stage_rate > VC7_FOD_1ST_STAGE_RATE_MAX) { |
| allow_frac = 1; |
| i = best_frac_i; |
| |
| /* Restore the best frac and rerun the loop for the last time */ |
| if (best_frac_i != VC7_FOD_2ND_INT_MIN) |
| i--; |
| |
| continue; |
| } |
| } |
| } |
| } |
| |
| static unsigned long vc7_fod_recalc_rate(struct clk_hw *hw, unsigned long parent_rate) |
| { |
| struct vc7_fod_data *fod = container_of(hw, struct vc7_fod_data, hw); |
| struct vc7_driver_data *vc7 = fod->vc7; |
| int err; |
| unsigned long fod_rate; |
| |
| err = vc7_read_fod(vc7, fod->num); |
| if (err) { |
| dev_err(&vc7->client->dev, "error reading registers for %s\n", |
| clk_hw_get_name(hw)); |
| return err; |
| } |
| |
| pr_debug("%s - %s: parent_rate: %lu\n", __func__, clk_hw_get_name(hw), parent_rate); |
| |
| fod_rate = vc7_calc_fod_2nd_stage_rate(parent_rate, fod->fod_1st_int, |
| fod->fod_2nd_int, fod->fod_frac); |
| |
| pr_debug("%s - %s: fod_1st_int: %u, fod_2nd_int: %u, fod_frac: %llu\n", |
| __func__, clk_hw_get_name(hw), |
| fod->fod_1st_int, fod->fod_2nd_int, fod->fod_frac); |
| pr_debug("%s - %s rate: %lu\n", __func__, clk_hw_get_name(hw), fod_rate); |
| |
| return fod_rate; |
| } |
| |
| static long vc7_fod_round_rate(struct clk_hw *hw, unsigned long rate, unsigned long *parent_rate) |
| { |
| struct vc7_fod_data *fod = container_of(hw, struct vc7_fod_data, hw); |
| unsigned long fod_rate; |
| |
| pr_debug("%s - %s: requested rate: %lu, parent_rate: %lu\n", |
| __func__, clk_hw_get_name(hw), rate, *parent_rate); |
| |
| vc7_calc_fod_divider(rate, *parent_rate, |
| &fod->fod_1st_int, &fod->fod_2nd_int, &fod->fod_frac); |
| fod_rate = vc7_calc_fod_2nd_stage_rate(*parent_rate, fod->fod_1st_int, |
| fod->fod_2nd_int, fod->fod_frac); |
| |
| pr_debug("%s - %s: fod_1st_int: %u, fod_2nd_int: %u, fod_frac: %llu\n", |
| __func__, clk_hw_get_name(hw), |
| fod->fod_1st_int, fod->fod_2nd_int, fod->fod_frac); |
| pr_debug("%s - %s rate: %lu\n", __func__, clk_hw_get_name(hw), fod_rate); |
| |
| return fod_rate; |
| } |
| |
| static int vc7_fod_set_rate(struct clk_hw *hw, unsigned long rate, unsigned long parent_rate) |
| { |
| struct vc7_fod_data *fod = container_of(hw, struct vc7_fod_data, hw); |
| struct vc7_driver_data *vc7 = fod->vc7; |
| unsigned long fod_rate; |
| |
| pr_debug("%s - %s: rate: %lu, parent_rate: %lu\n", |
| __func__, clk_hw_get_name(hw), rate, parent_rate); |
| |
| if (rate < VC7_FOD_RATE_MIN || rate > VC7_FOD_RATE_MAX) { |
| dev_err(&vc7->client->dev, |
| "requested frequency %lu Hz for %s is out of range\n", |
| rate, clk_hw_get_name(hw)); |
| return -EINVAL; |
| } |
| |
| vc7_write_fod(vc7, fod->num); |
| |
| fod_rate = vc7_calc_fod_2nd_stage_rate(parent_rate, fod->fod_1st_int, |
| fod->fod_2nd_int, fod->fod_frac); |
| |
| pr_debug("%s - %s: fod_1st_int: %u, fod_2nd_int: %u, fod_frac: %llu\n", |
| __func__, clk_hw_get_name(hw), |
| fod->fod_1st_int, fod->fod_2nd_int, fod->fod_frac); |
| pr_debug("%s - %s rate: %lu\n", __func__, clk_hw_get_name(hw), fod_rate); |
| |
| return 0; |
| } |
| |
| static const struct clk_ops vc7_fod_ops = { |
| .recalc_rate = vc7_fod_recalc_rate, |
| .round_rate = vc7_fod_round_rate, |
| .set_rate = vc7_fod_set_rate, |
| }; |
| |
| static unsigned long vc7_iod_recalc_rate(struct clk_hw *hw, unsigned long parent_rate) |
| { |
| struct vc7_iod_data *iod = container_of(hw, struct vc7_iod_data, hw); |
| struct vc7_driver_data *vc7 = iod->vc7; |
| int err; |
| unsigned long iod_rate; |
| |
| err = vc7_read_iod(vc7, iod->num); |
| if (err) { |
| dev_err(&vc7->client->dev, "error reading registers for %s\n", |
| clk_hw_get_name(hw)); |
| return err; |
| } |
| |
| iod_rate = div64_u64(parent_rate, iod->iod_int); |
| |
| pr_debug("%s - %s: iod_int: %u\n", __func__, clk_hw_get_name(hw), iod->iod_int); |
| pr_debug("%s - %s rate: %lu\n", __func__, clk_hw_get_name(hw), iod_rate); |
| |
| return iod_rate; |
| } |
| |
| static long vc7_iod_round_rate(struct clk_hw *hw, unsigned long rate, unsigned long *parent_rate) |
| { |
| struct vc7_iod_data *iod = container_of(hw, struct vc7_iod_data, hw); |
| unsigned long iod_rate; |
| |
| pr_debug("%s - %s: requested rate: %lu, parent_rate: %lu\n", |
| __func__, clk_hw_get_name(hw), rate, *parent_rate); |
| |
| vc7_calc_iod_divider(rate, *parent_rate, &iod->iod_int); |
| iod_rate = div64_u64(*parent_rate, iod->iod_int); |
| |
| pr_debug("%s - %s: iod_int: %u\n", __func__, clk_hw_get_name(hw), iod->iod_int); |
| pr_debug("%s - %s rate: %ld\n", __func__, clk_hw_get_name(hw), iod_rate); |
| |
| return iod_rate; |
| } |
| |
| static int vc7_iod_set_rate(struct clk_hw *hw, unsigned long rate, unsigned long parent_rate) |
| { |
| struct vc7_iod_data *iod = container_of(hw, struct vc7_iod_data, hw); |
| struct vc7_driver_data *vc7 = iod->vc7; |
| unsigned long iod_rate; |
| |
| pr_debug("%s - %s: rate: %lu, parent_rate: %lu\n", |
| __func__, clk_hw_get_name(hw), rate, parent_rate); |
| |
| if (rate < VC7_IOD_RATE_MIN || rate > VC7_IOD_RATE_MAX) { |
| dev_err(&vc7->client->dev, |
| "requested frequency %lu Hz for %s is out of range\n", |
| rate, clk_hw_get_name(hw)); |
| return -EINVAL; |
| } |
| |
| vc7_write_iod(vc7, iod->num); |
| |
| iod_rate = div64_u64(parent_rate, iod->iod_int); |
| |
| pr_debug("%s - %s: iod_int: %u\n", __func__, clk_hw_get_name(hw), iod->iod_int); |
| pr_debug("%s - %s rate: %ld\n", __func__, clk_hw_get_name(hw), iod_rate); |
| |
| return 0; |
| } |
| |
| static const struct clk_ops vc7_iod_ops = { |
| .recalc_rate = vc7_iod_recalc_rate, |
| .round_rate = vc7_iod_round_rate, |
| .set_rate = vc7_iod_set_rate, |
| }; |
| |
| static int vc7_clk_out_prepare(struct clk_hw *hw) |
| { |
| struct vc7_out_data *out = container_of(hw, struct vc7_out_data, hw); |
| struct vc7_driver_data *vc7 = out->vc7; |
| int err; |
| |
| out->out_dis = 0; |
| |
| err = vc7_write_output(vc7, out->num); |
| if (err) { |
| dev_err(&vc7->client->dev, "error writing registers for %s\n", |
| clk_hw_get_name(hw)); |
| return err; |
| } |
| |
| pr_debug("%s - %s: clk prepared\n", __func__, clk_hw_get_name(hw)); |
| |
| return 0; |
| } |
| |
| static void vc7_clk_out_unprepare(struct clk_hw *hw) |
| { |
| struct vc7_out_data *out = container_of(hw, struct vc7_out_data, hw); |
| struct vc7_driver_data *vc7 = out->vc7; |
| int err; |
| |
| out->out_dis = 1; |
| |
| err = vc7_write_output(vc7, out->num); |
| if (err) { |
| dev_err(&vc7->client->dev, "error writing registers for %s\n", |
| clk_hw_get_name(hw)); |
| return; |
| } |
| |
| pr_debug("%s - %s: clk unprepared\n", __func__, clk_hw_get_name(hw)); |
| } |
| |
| static int vc7_clk_out_is_enabled(struct clk_hw *hw) |
| { |
| struct vc7_out_data *out = container_of(hw, struct vc7_out_data, hw); |
| struct vc7_driver_data *vc7 = out->vc7; |
| int err, is_enabled; |
| |
| err = vc7_read_output(vc7, out->num); |
| if (err) { |
| dev_err(&vc7->client->dev, "error reading registers for %s\n", |
| clk_hw_get_name(hw)); |
| return err; |
| } |
| |
| is_enabled = !out->out_dis; |
| |
| pr_debug("%s - %s: is_enabled=%d\n", __func__, clk_hw_get_name(hw), is_enabled); |
| |
| return is_enabled; |
| } |
| |
| static const struct clk_ops vc7_clk_out_ops = { |
| .prepare = vc7_clk_out_prepare, |
| .unprepare = vc7_clk_out_unprepare, |
| .is_enabled = vc7_clk_out_is_enabled, |
| }; |
| |
| static int vc7_probe(struct i2c_client *client) |
| { |
| struct vc7_driver_data *vc7; |
| struct clk_init_data clk_init; |
| struct vc7_bank_src_map bank_src_map; |
| const char *node_name, *apll_name; |
| const char *parent_names[1]; |
| unsigned int i, val, bank_idx, out_num; |
| unsigned long apll_rate; |
| int ret; |
| |
| vc7 = devm_kzalloc(&client->dev, sizeof(*vc7), GFP_KERNEL); |
| if (!vc7) |
| return -ENOMEM; |
| |
| i2c_set_clientdata(client, vc7); |
| vc7->client = client; |
| vc7->chip_info = of_device_get_match_data(&client->dev); |
| |
| vc7->pin_xin = devm_clk_get(&client->dev, "xin"); |
| if (PTR_ERR(vc7->pin_xin) == -EPROBE_DEFER) { |
| return dev_err_probe(&client->dev, -EPROBE_DEFER, |
| "xin not specified\n"); |
| } |
| |
| vc7->regmap = devm_regmap_init_i2c(client, &vc7_regmap_config); |
| if (IS_ERR(vc7->regmap)) { |
| return dev_err_probe(&client->dev, PTR_ERR(vc7->regmap), |
| "failed to allocate register map\n"); |
| } |
| |
| if (of_property_read_string(client->dev.of_node, "clock-output-names", |
| &node_name)) |
| node_name = client->dev.of_node->name; |
| |
| /* Register APLL */ |
| apll_rate = vc7_get_apll_rate(vc7); |
| apll_name = kasprintf(GFP_KERNEL, "%s_apll", node_name); |
| vc7->clk_apll.clk = clk_register_fixed_rate(&client->dev, apll_name, |
| __clk_get_name(vc7->pin_xin), |
| 0, apll_rate); |
| kfree(apll_name); /* ccf made a copy of the name */ |
| if (IS_ERR(vc7->clk_apll.clk)) { |
| return dev_err_probe(&client->dev, PTR_ERR(vc7->clk_apll.clk), |
| "failed to register apll\n"); |
| } |
| |
| /* Register FODs */ |
| for (i = 0; i < VC7_NUM_FOD; i++) { |
| memset(&clk_init, 0, sizeof(clk_init)); |
| clk_init.name = kasprintf(GFP_KERNEL, "%s_fod%d", node_name, i); |
| clk_init.ops = &vc7_fod_ops; |
| clk_init.parent_names = parent_names; |
| parent_names[0] = __clk_get_name(vc7->clk_apll.clk); |
| clk_init.num_parents = 1; |
| vc7->clk_fod[i].num = i; |
| vc7->clk_fod[i].vc7 = vc7; |
| vc7->clk_fod[i].hw.init = &clk_init; |
| ret = devm_clk_hw_register(&client->dev, &vc7->clk_fod[i].hw); |
| if (ret) |
| goto err_clk_register; |
| kfree(clk_init.name); /* ccf made a copy of the name */ |
| } |
| |
| /* Register IODs */ |
| for (i = 0; i < VC7_NUM_IOD; i++) { |
| memset(&clk_init, 0, sizeof(clk_init)); |
| clk_init.name = kasprintf(GFP_KERNEL, "%s_iod%d", node_name, i); |
| clk_init.ops = &vc7_iod_ops; |
| clk_init.parent_names = parent_names; |
| parent_names[0] = __clk_get_name(vc7->clk_apll.clk); |
| clk_init.num_parents = 1; |
| vc7->clk_iod[i].num = i; |
| vc7->clk_iod[i].vc7 = vc7; |
| vc7->clk_iod[i].hw.init = &clk_init; |
| ret = devm_clk_hw_register(&client->dev, &vc7->clk_iod[i].hw); |
| if (ret) |
| goto err_clk_register; |
| kfree(clk_init.name); /* ccf made a copy of the name */ |
| } |
| |
| /* Register outputs */ |
| for (i = 0; i < vc7->chip_info->num_outputs; i++) { |
| out_num = vc7_map_index_to_output(vc7->chip_info->model, i); |
| |
| /* |
| * This driver does not support remapping FOD/IOD to banks. |
| * The device state is read and the driver is setup to match |
| * the device's existing mapping. |
| */ |
| bank_idx = output_bank_mapping[out_num]; |
| |
| regmap_read(vc7->regmap, VC7_REG_OUT_BANK_CNFG(bank_idx), &val); |
| val &= VC7_REG_OUTPUT_BANK_SRC_MASK; |
| |
| memset(&bank_src_map, 0, sizeof(bank_src_map)); |
| ret = vc7_get_bank_clk(vc7, bank_idx, val, &bank_src_map); |
| if (ret) { |
| dev_err_probe(&client->dev, ret, |
| "unable to register output %d\n", i); |
| return ret; |
| } |
| |
| switch (bank_src_map.type) { |
| case VC7_FOD: |
| parent_names[0] = clk_hw_get_name(&bank_src_map.src.fod->hw); |
| break; |
| case VC7_IOD: |
| parent_names[0] = clk_hw_get_name(&bank_src_map.src.iod->hw); |
| break; |
| } |
| |
| memset(&clk_init, 0, sizeof(clk_init)); |
| clk_init.name = kasprintf(GFP_KERNEL, "%s_out%d", node_name, i); |
| clk_init.ops = &vc7_clk_out_ops; |
| clk_init.flags = CLK_SET_RATE_PARENT; |
| clk_init.parent_names = parent_names; |
| clk_init.num_parents = 1; |
| vc7->clk_out[i].num = i; |
| vc7->clk_out[i].vc7 = vc7; |
| vc7->clk_out[i].hw.init = &clk_init; |
| ret = devm_clk_hw_register(&client->dev, &vc7->clk_out[i].hw); |
| if (ret) |
| goto err_clk_register; |
| kfree(clk_init.name); /* ccf made a copy of the name */ |
| } |
| |
| ret = of_clk_add_hw_provider(client->dev.of_node, vc7_of_clk_get, vc7); |
| if (ret) { |
| dev_err_probe(&client->dev, ret, "unable to add clk provider\n"); |
| goto err_clk; |
| } |
| |
| return ret; |
| |
| err_clk_register: |
| dev_err_probe(&client->dev, ret, |
| "unable to register %s\n", clk_init.name); |
| kfree(clk_init.name); /* ccf made a copy of the name */ |
| err_clk: |
| clk_unregister_fixed_rate(vc7->clk_apll.clk); |
| return ret; |
| } |
| |
| static void vc7_remove(struct i2c_client *client) |
| { |
| struct vc7_driver_data *vc7 = i2c_get_clientdata(client); |
| |
| of_clk_del_provider(client->dev.of_node); |
| clk_unregister_fixed_rate(vc7->clk_apll.clk); |
| } |
| |
| static bool vc7_volatile_reg(struct device *dev, unsigned int reg) |
| { |
| if (reg == VC7_PAGE_ADDR) |
| return false; |
| |
| return true; |
| } |
| |
| static const struct vc7_chip_info vc7_rc21008a_info = { |
| .model = VC7_RC21008A, |
| .num_banks = 6, |
| .num_outputs = 8, |
| }; |
| |
| static struct regmap_range_cfg vc7_range_cfg[] = { |
| { |
| .range_min = 0, |
| .range_max = VC7_MAX_REG, |
| .selector_reg = VC7_PAGE_ADDR, |
| .selector_mask = 0xFF, |
| .selector_shift = 0, |
| .window_start = 0, |
| .window_len = VC7_PAGE_WINDOW, |
| }}; |
| |
| static const struct regmap_config vc7_regmap_config = { |
| .reg_bits = 8, |
| .val_bits = 8, |
| .max_register = VC7_MAX_REG, |
| .ranges = vc7_range_cfg, |
| .num_ranges = ARRAY_SIZE(vc7_range_cfg), |
| .volatile_reg = vc7_volatile_reg, |
| .cache_type = REGCACHE_RBTREE, |
| .can_multi_write = true, |
| .reg_format_endian = REGMAP_ENDIAN_LITTLE, |
| .val_format_endian = REGMAP_ENDIAN_LITTLE, |
| }; |
| |
| static const struct i2c_device_id vc7_i2c_id[] = { |
| { "rc21008a", VC7_RC21008A }, |
| {} |
| }; |
| MODULE_DEVICE_TABLE(i2c, vc7_i2c_id); |
| |
| static const struct of_device_id vc7_of_match[] = { |
| { .compatible = "renesas,rc21008a", .data = &vc7_rc21008a_info }, |
| {} |
| }; |
| MODULE_DEVICE_TABLE(of, vc7_of_match); |
| |
| static struct i2c_driver vc7_i2c_driver = { |
| .driver = { |
| .name = "vc7", |
| .of_match_table = vc7_of_match, |
| }, |
| .probe_new = vc7_probe, |
| .remove = vc7_remove, |
| .id_table = vc7_i2c_id, |
| }; |
| module_i2c_driver(vc7_i2c_driver); |
| |
| MODULE_LICENSE("GPL"); |
| MODULE_AUTHOR("Alex Helms <alexander.helms.jy@renesas.com"); |
| MODULE_DESCRIPTION("Renesas Versaclock7 common clock framework driver"); |