| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * Driver for STM32 Digital Camera Memory Interface |
| * |
| * Copyright (C) STMicroelectronics SA 2017 |
| * Authors: Yannick Fertre <yannick.fertre@st.com> |
| * Hugues Fruchet <hugues.fruchet@st.com> |
| * for STMicroelectronics. |
| * |
| * This driver is based on atmel_isi.c |
| * |
| */ |
| |
| #include <linux/clk.h> |
| #include <linux/completion.h> |
| #include <linux/delay.h> |
| #include <linux/dmaengine.h> |
| #include <linux/init.h> |
| #include <linux/interrupt.h> |
| #include <linux/kernel.h> |
| #include <linux/module.h> |
| #include <linux/of.h> |
| #include <linux/of_device.h> |
| #include <linux/of_graph.h> |
| #include <linux/pinctrl/consumer.h> |
| #include <linux/platform_device.h> |
| #include <linux/pm_runtime.h> |
| #include <linux/reset.h> |
| #include <linux/videodev2.h> |
| |
| #include <media/v4l2-ctrls.h> |
| #include <media/v4l2-dev.h> |
| #include <media/v4l2-device.h> |
| #include <media/v4l2-event.h> |
| #include <media/v4l2-fwnode.h> |
| #include <media/v4l2-image-sizes.h> |
| #include <media/v4l2-ioctl.h> |
| #include <media/v4l2-rect.h> |
| #include <media/videobuf2-dma-contig.h> |
| |
| #define DRV_NAME "stm32-dcmi" |
| |
| /* Registers offset for DCMI */ |
| #define DCMI_CR 0x00 /* Control Register */ |
| #define DCMI_SR 0x04 /* Status Register */ |
| #define DCMI_RIS 0x08 /* Raw Interrupt Status register */ |
| #define DCMI_IER 0x0C /* Interrupt Enable Register */ |
| #define DCMI_MIS 0x10 /* Masked Interrupt Status register */ |
| #define DCMI_ICR 0x14 /* Interrupt Clear Register */ |
| #define DCMI_ESCR 0x18 /* Embedded Synchronization Code Register */ |
| #define DCMI_ESUR 0x1C /* Embedded Synchronization Unmask Register */ |
| #define DCMI_CWSTRT 0x20 /* Crop Window STaRT */ |
| #define DCMI_CWSIZE 0x24 /* Crop Window SIZE */ |
| #define DCMI_DR 0x28 /* Data Register */ |
| #define DCMI_IDR 0x2C /* IDentifier Register */ |
| |
| /* Bits definition for control register (DCMI_CR) */ |
| #define CR_CAPTURE BIT(0) |
| #define CR_CM BIT(1) |
| #define CR_CROP BIT(2) |
| #define CR_JPEG BIT(3) |
| #define CR_ESS BIT(4) |
| #define CR_PCKPOL BIT(5) |
| #define CR_HSPOL BIT(6) |
| #define CR_VSPOL BIT(7) |
| #define CR_FCRC_0 BIT(8) |
| #define CR_FCRC_1 BIT(9) |
| #define CR_EDM_0 BIT(10) |
| #define CR_EDM_1 BIT(11) |
| #define CR_ENABLE BIT(14) |
| |
| /* Bits definition for status register (DCMI_SR) */ |
| #define SR_HSYNC BIT(0) |
| #define SR_VSYNC BIT(1) |
| #define SR_FNE BIT(2) |
| |
| /* |
| * Bits definition for interrupt registers |
| * (DCMI_RIS, DCMI_IER, DCMI_MIS, DCMI_ICR) |
| */ |
| #define IT_FRAME BIT(0) |
| #define IT_OVR BIT(1) |
| #define IT_ERR BIT(2) |
| #define IT_VSYNC BIT(3) |
| #define IT_LINE BIT(4) |
| |
| enum state { |
| STOPPED = 0, |
| WAIT_FOR_BUFFER, |
| RUNNING, |
| }; |
| |
| #define MIN_WIDTH 16U |
| #define MAX_WIDTH 2592U |
| #define MIN_HEIGHT 16U |
| #define MAX_HEIGHT 2592U |
| |
| #define TIMEOUT_MS 1000 |
| |
| #define OVERRUN_ERROR_THRESHOLD 3 |
| |
| struct dcmi_format { |
| u32 fourcc; |
| u32 mbus_code; |
| u8 bpp; |
| }; |
| |
| struct dcmi_framesize { |
| u32 width; |
| u32 height; |
| }; |
| |
| struct dcmi_buf { |
| struct vb2_v4l2_buffer vb; |
| bool prepared; |
| dma_addr_t paddr; |
| size_t size; |
| struct list_head list; |
| }; |
| |
| struct stm32_dcmi { |
| /* Protects the access of variables shared within the interrupt */ |
| spinlock_t irqlock; |
| struct device *dev; |
| void __iomem *regs; |
| struct resource *res; |
| struct reset_control *rstc; |
| int sequence; |
| struct list_head buffers; |
| struct dcmi_buf *active; |
| |
| struct v4l2_device v4l2_dev; |
| struct video_device *vdev; |
| struct v4l2_async_notifier notifier; |
| struct v4l2_subdev *source; |
| struct v4l2_format fmt; |
| struct v4l2_rect crop; |
| bool do_crop; |
| |
| const struct dcmi_format **sd_formats; |
| unsigned int num_of_sd_formats; |
| const struct dcmi_format *sd_format; |
| struct dcmi_framesize *sd_framesizes; |
| unsigned int num_of_sd_framesizes; |
| struct dcmi_framesize sd_framesize; |
| struct v4l2_rect sd_bounds; |
| |
| /* Protect this data structure */ |
| struct mutex lock; |
| struct vb2_queue queue; |
| |
| struct v4l2_fwnode_bus_parallel bus; |
| enum v4l2_mbus_type bus_type; |
| struct completion complete; |
| struct clk *mclk; |
| enum state state; |
| struct dma_chan *dma_chan; |
| dma_cookie_t dma_cookie; |
| u32 misr; |
| int errors_count; |
| int overrun_count; |
| int buffers_count; |
| |
| /* Ensure DMA operations atomicity */ |
| struct mutex dma_lock; |
| |
| struct media_device mdev; |
| struct media_pad vid_cap_pad; |
| struct media_pipeline pipeline; |
| }; |
| |
| static inline struct stm32_dcmi *notifier_to_dcmi(struct v4l2_async_notifier *n) |
| { |
| return container_of(n, struct stm32_dcmi, notifier); |
| } |
| |
| static inline u32 reg_read(void __iomem *base, u32 reg) |
| { |
| return readl_relaxed(base + reg); |
| } |
| |
| static inline void reg_write(void __iomem *base, u32 reg, u32 val) |
| { |
| writel_relaxed(val, base + reg); |
| } |
| |
| static inline void reg_set(void __iomem *base, u32 reg, u32 mask) |
| { |
| reg_write(base, reg, reg_read(base, reg) | mask); |
| } |
| |
| static inline void reg_clear(void __iomem *base, u32 reg, u32 mask) |
| { |
| reg_write(base, reg, reg_read(base, reg) & ~mask); |
| } |
| |
| static int dcmi_start_capture(struct stm32_dcmi *dcmi, struct dcmi_buf *buf); |
| |
| static void dcmi_buffer_done(struct stm32_dcmi *dcmi, |
| struct dcmi_buf *buf, |
| size_t bytesused, |
| int err) |
| { |
| struct vb2_v4l2_buffer *vbuf; |
| |
| if (!buf) |
| return; |
| |
| list_del_init(&buf->list); |
| |
| vbuf = &buf->vb; |
| |
| vbuf->sequence = dcmi->sequence++; |
| vbuf->field = V4L2_FIELD_NONE; |
| vbuf->vb2_buf.timestamp = ktime_get_ns(); |
| vb2_set_plane_payload(&vbuf->vb2_buf, 0, bytesused); |
| vb2_buffer_done(&vbuf->vb2_buf, |
| err ? VB2_BUF_STATE_ERROR : VB2_BUF_STATE_DONE); |
| dev_dbg(dcmi->dev, "buffer[%d] done seq=%d, bytesused=%zu\n", |
| vbuf->vb2_buf.index, vbuf->sequence, bytesused); |
| |
| dcmi->buffers_count++; |
| dcmi->active = NULL; |
| } |
| |
| static int dcmi_restart_capture(struct stm32_dcmi *dcmi) |
| { |
| struct dcmi_buf *buf; |
| |
| spin_lock_irq(&dcmi->irqlock); |
| |
| if (dcmi->state != RUNNING) { |
| spin_unlock_irq(&dcmi->irqlock); |
| return -EINVAL; |
| } |
| |
| /* Restart a new DMA transfer with next buffer */ |
| if (list_empty(&dcmi->buffers)) { |
| dev_dbg(dcmi->dev, "Capture restart is deferred to next buffer queueing\n"); |
| dcmi->state = WAIT_FOR_BUFFER; |
| spin_unlock_irq(&dcmi->irqlock); |
| return 0; |
| } |
| buf = list_entry(dcmi->buffers.next, struct dcmi_buf, list); |
| dcmi->active = buf; |
| |
| spin_unlock_irq(&dcmi->irqlock); |
| |
| return dcmi_start_capture(dcmi, buf); |
| } |
| |
| static void dcmi_dma_callback(void *param) |
| { |
| struct stm32_dcmi *dcmi = (struct stm32_dcmi *)param; |
| struct dma_tx_state state; |
| enum dma_status status; |
| struct dcmi_buf *buf = dcmi->active; |
| |
| spin_lock_irq(&dcmi->irqlock); |
| |
| /* Check DMA status */ |
| status = dmaengine_tx_status(dcmi->dma_chan, dcmi->dma_cookie, &state); |
| |
| switch (status) { |
| case DMA_IN_PROGRESS: |
| dev_dbg(dcmi->dev, "%s: Received DMA_IN_PROGRESS\n", __func__); |
| break; |
| case DMA_PAUSED: |
| dev_err(dcmi->dev, "%s: Received DMA_PAUSED\n", __func__); |
| break; |
| case DMA_ERROR: |
| dev_err(dcmi->dev, "%s: Received DMA_ERROR\n", __func__); |
| |
| /* Return buffer to V4L2 in error state */ |
| dcmi_buffer_done(dcmi, buf, 0, -EIO); |
| break; |
| case DMA_COMPLETE: |
| dev_dbg(dcmi->dev, "%s: Received DMA_COMPLETE\n", __func__); |
| |
| /* Return buffer to V4L2 */ |
| dcmi_buffer_done(dcmi, buf, buf->size, 0); |
| |
| spin_unlock_irq(&dcmi->irqlock); |
| |
| /* Restart capture */ |
| if (dcmi_restart_capture(dcmi)) |
| dev_err(dcmi->dev, "%s: Cannot restart capture on DMA complete\n", |
| __func__); |
| return; |
| default: |
| dev_err(dcmi->dev, "%s: Received unknown status\n", __func__); |
| break; |
| } |
| |
| spin_unlock_irq(&dcmi->irqlock); |
| } |
| |
| static int dcmi_start_dma(struct stm32_dcmi *dcmi, |
| struct dcmi_buf *buf) |
| { |
| struct dma_async_tx_descriptor *desc = NULL; |
| struct dma_slave_config config; |
| int ret; |
| |
| memset(&config, 0, sizeof(config)); |
| |
| config.src_addr = (dma_addr_t)dcmi->res->start + DCMI_DR; |
| config.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES; |
| config.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES; |
| config.dst_maxburst = 4; |
| |
| /* Configure DMA channel */ |
| ret = dmaengine_slave_config(dcmi->dma_chan, &config); |
| if (ret < 0) { |
| dev_err(dcmi->dev, "%s: DMA channel config failed (%d)\n", |
| __func__, ret); |
| return ret; |
| } |
| |
| /* |
| * Avoid call of dmaengine_terminate_sync() between |
| * dmaengine_prep_slave_single() and dmaengine_submit() |
| * by locking the whole DMA submission sequence |
| */ |
| mutex_lock(&dcmi->dma_lock); |
| |
| /* Prepare a DMA transaction */ |
| desc = dmaengine_prep_slave_single(dcmi->dma_chan, buf->paddr, |
| buf->size, |
| DMA_DEV_TO_MEM, |
| DMA_PREP_INTERRUPT); |
| if (!desc) { |
| dev_err(dcmi->dev, "%s: DMA dmaengine_prep_slave_single failed for buffer phy=%pad size=%zu\n", |
| __func__, &buf->paddr, buf->size); |
| mutex_unlock(&dcmi->dma_lock); |
| return -EINVAL; |
| } |
| |
| /* Set completion callback routine for notification */ |
| desc->callback = dcmi_dma_callback; |
| desc->callback_param = dcmi; |
| |
| /* Push current DMA transaction in the pending queue */ |
| dcmi->dma_cookie = dmaengine_submit(desc); |
| if (dma_submit_error(dcmi->dma_cookie)) { |
| dev_err(dcmi->dev, "%s: DMA submission failed\n", __func__); |
| mutex_unlock(&dcmi->dma_lock); |
| return -ENXIO; |
| } |
| |
| mutex_unlock(&dcmi->dma_lock); |
| |
| dma_async_issue_pending(dcmi->dma_chan); |
| |
| return 0; |
| } |
| |
| static int dcmi_start_capture(struct stm32_dcmi *dcmi, struct dcmi_buf *buf) |
| { |
| int ret; |
| |
| if (!buf) |
| return -EINVAL; |
| |
| ret = dcmi_start_dma(dcmi, buf); |
| if (ret) { |
| dcmi->errors_count++; |
| return ret; |
| } |
| |
| /* Enable capture */ |
| reg_set(dcmi->regs, DCMI_CR, CR_CAPTURE); |
| |
| return 0; |
| } |
| |
| static void dcmi_set_crop(struct stm32_dcmi *dcmi) |
| { |
| u32 size, start; |
| |
| /* Crop resolution */ |
| size = ((dcmi->crop.height - 1) << 16) | |
| ((dcmi->crop.width << 1) - 1); |
| reg_write(dcmi->regs, DCMI_CWSIZE, size); |
| |
| /* Crop start point */ |
| start = ((dcmi->crop.top) << 16) | |
| ((dcmi->crop.left << 1)); |
| reg_write(dcmi->regs, DCMI_CWSTRT, start); |
| |
| dev_dbg(dcmi->dev, "Cropping to %ux%u@%u:%u\n", |
| dcmi->crop.width, dcmi->crop.height, |
| dcmi->crop.left, dcmi->crop.top); |
| |
| /* Enable crop */ |
| reg_set(dcmi->regs, DCMI_CR, CR_CROP); |
| } |
| |
| static void dcmi_process_jpeg(struct stm32_dcmi *dcmi) |
| { |
| struct dma_tx_state state; |
| enum dma_status status; |
| struct dcmi_buf *buf = dcmi->active; |
| |
| if (!buf) |
| return; |
| |
| /* |
| * Because of variable JPEG buffer size sent by sensor, |
| * DMA transfer never completes due to transfer size never reached. |
| * In order to ensure that all the JPEG data are transferred |
| * in active buffer memory, DMA is drained. |
| * Then DMA tx status gives the amount of data transferred |
| * to memory, which is then returned to V4L2 through the active |
| * buffer payload. |
| */ |
| |
| /* Drain DMA */ |
| dmaengine_synchronize(dcmi->dma_chan); |
| |
| /* Get DMA residue to get JPEG size */ |
| status = dmaengine_tx_status(dcmi->dma_chan, dcmi->dma_cookie, &state); |
| if (status != DMA_ERROR && state.residue < buf->size) { |
| /* Return JPEG buffer to V4L2 with received JPEG buffer size */ |
| dcmi_buffer_done(dcmi, buf, buf->size - state.residue, 0); |
| } else { |
| dcmi->errors_count++; |
| dev_err(dcmi->dev, "%s: Cannot get JPEG size from DMA\n", |
| __func__); |
| /* Return JPEG buffer to V4L2 in ERROR state */ |
| dcmi_buffer_done(dcmi, buf, 0, -EIO); |
| } |
| |
| /* Abort DMA operation */ |
| dmaengine_terminate_sync(dcmi->dma_chan); |
| |
| /* Restart capture */ |
| if (dcmi_restart_capture(dcmi)) |
| dev_err(dcmi->dev, "%s: Cannot restart capture on JPEG received\n", |
| __func__); |
| } |
| |
| static irqreturn_t dcmi_irq_thread(int irq, void *arg) |
| { |
| struct stm32_dcmi *dcmi = arg; |
| |
| spin_lock_irq(&dcmi->irqlock); |
| |
| if (dcmi->misr & IT_OVR) { |
| dcmi->overrun_count++; |
| if (dcmi->overrun_count > OVERRUN_ERROR_THRESHOLD) |
| dcmi->errors_count++; |
| } |
| if (dcmi->misr & IT_ERR) |
| dcmi->errors_count++; |
| |
| if (dcmi->sd_format->fourcc == V4L2_PIX_FMT_JPEG && |
| dcmi->misr & IT_FRAME) { |
| /* JPEG received */ |
| spin_unlock_irq(&dcmi->irqlock); |
| dcmi_process_jpeg(dcmi); |
| return IRQ_HANDLED; |
| } |
| |
| spin_unlock_irq(&dcmi->irqlock); |
| return IRQ_HANDLED; |
| } |
| |
| static irqreturn_t dcmi_irq_callback(int irq, void *arg) |
| { |
| struct stm32_dcmi *dcmi = arg; |
| unsigned long flags; |
| |
| spin_lock_irqsave(&dcmi->irqlock, flags); |
| |
| dcmi->misr = reg_read(dcmi->regs, DCMI_MIS); |
| |
| /* Clear interrupt */ |
| reg_set(dcmi->regs, DCMI_ICR, IT_FRAME | IT_OVR | IT_ERR); |
| |
| spin_unlock_irqrestore(&dcmi->irqlock, flags); |
| |
| return IRQ_WAKE_THREAD; |
| } |
| |
| static int dcmi_queue_setup(struct vb2_queue *vq, |
| unsigned int *nbuffers, |
| unsigned int *nplanes, |
| unsigned int sizes[], |
| struct device *alloc_devs[]) |
| { |
| struct stm32_dcmi *dcmi = vb2_get_drv_priv(vq); |
| unsigned int size; |
| |
| size = dcmi->fmt.fmt.pix.sizeimage; |
| |
| /* Make sure the image size is large enough */ |
| if (*nplanes) |
| return sizes[0] < size ? -EINVAL : 0; |
| |
| *nplanes = 1; |
| sizes[0] = size; |
| |
| dev_dbg(dcmi->dev, "Setup queue, count=%d, size=%d\n", |
| *nbuffers, size); |
| |
| return 0; |
| } |
| |
| static int dcmi_buf_init(struct vb2_buffer *vb) |
| { |
| struct vb2_v4l2_buffer *vbuf = to_vb2_v4l2_buffer(vb); |
| struct dcmi_buf *buf = container_of(vbuf, struct dcmi_buf, vb); |
| |
| INIT_LIST_HEAD(&buf->list); |
| |
| return 0; |
| } |
| |
| static int dcmi_buf_prepare(struct vb2_buffer *vb) |
| { |
| struct stm32_dcmi *dcmi = vb2_get_drv_priv(vb->vb2_queue); |
| struct vb2_v4l2_buffer *vbuf = to_vb2_v4l2_buffer(vb); |
| struct dcmi_buf *buf = container_of(vbuf, struct dcmi_buf, vb); |
| unsigned long size; |
| |
| size = dcmi->fmt.fmt.pix.sizeimage; |
| |
| if (vb2_plane_size(vb, 0) < size) { |
| dev_err(dcmi->dev, "%s data will not fit into plane (%lu < %lu)\n", |
| __func__, vb2_plane_size(vb, 0), size); |
| return -EINVAL; |
| } |
| |
| vb2_set_plane_payload(vb, 0, size); |
| |
| if (!buf->prepared) { |
| /* Get memory addresses */ |
| buf->paddr = |
| vb2_dma_contig_plane_dma_addr(&buf->vb.vb2_buf, 0); |
| buf->size = vb2_plane_size(&buf->vb.vb2_buf, 0); |
| buf->prepared = true; |
| |
| vb2_set_plane_payload(&buf->vb.vb2_buf, 0, buf->size); |
| |
| dev_dbg(dcmi->dev, "buffer[%d] phy=%pad size=%zu\n", |
| vb->index, &buf->paddr, buf->size); |
| } |
| |
| return 0; |
| } |
| |
| static void dcmi_buf_queue(struct vb2_buffer *vb) |
| { |
| struct stm32_dcmi *dcmi = vb2_get_drv_priv(vb->vb2_queue); |
| struct vb2_v4l2_buffer *vbuf = to_vb2_v4l2_buffer(vb); |
| struct dcmi_buf *buf = container_of(vbuf, struct dcmi_buf, vb); |
| |
| spin_lock_irq(&dcmi->irqlock); |
| |
| /* Enqueue to video buffers list */ |
| list_add_tail(&buf->list, &dcmi->buffers); |
| |
| if (dcmi->state == WAIT_FOR_BUFFER) { |
| dcmi->state = RUNNING; |
| dcmi->active = buf; |
| |
| dev_dbg(dcmi->dev, "Starting capture on buffer[%d] queued\n", |
| buf->vb.vb2_buf.index); |
| |
| spin_unlock_irq(&dcmi->irqlock); |
| if (dcmi_start_capture(dcmi, buf)) |
| dev_err(dcmi->dev, "%s: Cannot restart capture on overflow or error\n", |
| __func__); |
| return; |
| } |
| |
| spin_unlock_irq(&dcmi->irqlock); |
| } |
| |
| static struct media_entity *dcmi_find_source(struct stm32_dcmi *dcmi) |
| { |
| struct media_entity *entity = &dcmi->vdev->entity; |
| struct media_pad *pad; |
| |
| /* Walk searching for entity having no sink */ |
| while (1) { |
| pad = &entity->pads[0]; |
| if (!(pad->flags & MEDIA_PAD_FL_SINK)) |
| break; |
| |
| pad = media_entity_remote_pad(pad); |
| if (!pad || !is_media_entity_v4l2_subdev(pad->entity)) |
| break; |
| |
| entity = pad->entity; |
| } |
| |
| return entity; |
| } |
| |
| static int dcmi_pipeline_s_fmt(struct stm32_dcmi *dcmi, |
| struct v4l2_subdev_state *sd_state, |
| struct v4l2_subdev_format *format) |
| { |
| struct media_entity *entity = &dcmi->source->entity; |
| struct v4l2_subdev *subdev; |
| struct media_pad *sink_pad = NULL; |
| struct media_pad *src_pad = NULL; |
| struct media_pad *pad = NULL; |
| struct v4l2_subdev_format fmt = *format; |
| bool found = false; |
| int ret; |
| |
| /* |
| * Starting from sensor subdevice, walk within |
| * pipeline and set format on each subdevice |
| */ |
| while (1) { |
| unsigned int i; |
| |
| /* Search if current entity has a source pad */ |
| for (i = 0; i < entity->num_pads; i++) { |
| pad = &entity->pads[i]; |
| if (pad->flags & MEDIA_PAD_FL_SOURCE) { |
| src_pad = pad; |
| found = true; |
| break; |
| } |
| } |
| if (!found) |
| break; |
| |
| subdev = media_entity_to_v4l2_subdev(entity); |
| |
| /* Propagate format on sink pad if any, otherwise source pad */ |
| if (sink_pad) |
| pad = sink_pad; |
| |
| dev_dbg(dcmi->dev, "\"%s\":%d pad format set to 0x%x %ux%u\n", |
| subdev->name, pad->index, format->format.code, |
| format->format.width, format->format.height); |
| |
| fmt.pad = pad->index; |
| ret = v4l2_subdev_call(subdev, pad, set_fmt, sd_state, &fmt); |
| if (ret < 0) { |
| dev_err(dcmi->dev, "%s: Failed to set format 0x%x %ux%u on \"%s\":%d pad (%d)\n", |
| __func__, format->format.code, |
| format->format.width, format->format.height, |
| subdev->name, pad->index, ret); |
| return ret; |
| } |
| |
| if (fmt.format.code != format->format.code || |
| fmt.format.width != format->format.width || |
| fmt.format.height != format->format.height) { |
| dev_dbg(dcmi->dev, "\"%s\":%d pad format has been changed to 0x%x %ux%u\n", |
| subdev->name, pad->index, fmt.format.code, |
| fmt.format.width, fmt.format.height); |
| } |
| |
| /* Walk to next entity */ |
| sink_pad = media_entity_remote_pad(src_pad); |
| if (!sink_pad || !is_media_entity_v4l2_subdev(sink_pad->entity)) |
| break; |
| |
| entity = sink_pad->entity; |
| } |
| *format = fmt; |
| |
| return 0; |
| } |
| |
| static int dcmi_pipeline_s_stream(struct stm32_dcmi *dcmi, int state) |
| { |
| struct media_entity *entity = &dcmi->vdev->entity; |
| struct v4l2_subdev *subdev; |
| struct media_pad *pad; |
| int ret; |
| |
| /* Start/stop all entities within pipeline */ |
| while (1) { |
| pad = &entity->pads[0]; |
| if (!(pad->flags & MEDIA_PAD_FL_SINK)) |
| break; |
| |
| pad = media_entity_remote_pad(pad); |
| if (!pad || !is_media_entity_v4l2_subdev(pad->entity)) |
| break; |
| |
| entity = pad->entity; |
| subdev = media_entity_to_v4l2_subdev(entity); |
| |
| ret = v4l2_subdev_call(subdev, video, s_stream, state); |
| if (ret < 0 && ret != -ENOIOCTLCMD) { |
| dev_err(dcmi->dev, "%s: \"%s\" failed to %s streaming (%d)\n", |
| __func__, subdev->name, |
| state ? "start" : "stop", ret); |
| return ret; |
| } |
| |
| dev_dbg(dcmi->dev, "\"%s\" is %s\n", |
| subdev->name, state ? "started" : "stopped"); |
| } |
| |
| return 0; |
| } |
| |
| static int dcmi_pipeline_start(struct stm32_dcmi *dcmi) |
| { |
| return dcmi_pipeline_s_stream(dcmi, 1); |
| } |
| |
| static void dcmi_pipeline_stop(struct stm32_dcmi *dcmi) |
| { |
| dcmi_pipeline_s_stream(dcmi, 0); |
| } |
| |
| static int dcmi_start_streaming(struct vb2_queue *vq, unsigned int count) |
| { |
| struct stm32_dcmi *dcmi = vb2_get_drv_priv(vq); |
| struct dcmi_buf *buf, *node; |
| u32 val = 0; |
| int ret; |
| |
| ret = pm_runtime_resume_and_get(dcmi->dev); |
| if (ret < 0) { |
| dev_err(dcmi->dev, "%s: Failed to start streaming, cannot get sync (%d)\n", |
| __func__, ret); |
| goto err_unlocked; |
| } |
| |
| ret = media_pipeline_start(&dcmi->vdev->entity, &dcmi->pipeline); |
| if (ret < 0) { |
| dev_err(dcmi->dev, "%s: Failed to start streaming, media pipeline start error (%d)\n", |
| __func__, ret); |
| goto err_pm_put; |
| } |
| |
| ret = dcmi_pipeline_start(dcmi); |
| if (ret) |
| goto err_media_pipeline_stop; |
| |
| spin_lock_irq(&dcmi->irqlock); |
| |
| /* Set bus width */ |
| switch (dcmi->bus.bus_width) { |
| case 14: |
| val |= CR_EDM_0 | CR_EDM_1; |
| break; |
| case 12: |
| val |= CR_EDM_1; |
| break; |
| case 10: |
| val |= CR_EDM_0; |
| break; |
| default: |
| /* Set bus width to 8 bits by default */ |
| break; |
| } |
| |
| /* Set vertical synchronization polarity */ |
| if (dcmi->bus.flags & V4L2_MBUS_VSYNC_ACTIVE_HIGH) |
| val |= CR_VSPOL; |
| |
| /* Set horizontal synchronization polarity */ |
| if (dcmi->bus.flags & V4L2_MBUS_HSYNC_ACTIVE_HIGH) |
| val |= CR_HSPOL; |
| |
| /* Set pixel clock polarity */ |
| if (dcmi->bus.flags & V4L2_MBUS_PCLK_SAMPLE_RISING) |
| val |= CR_PCKPOL; |
| |
| /* |
| * BT656 embedded synchronisation bus mode. |
| * |
| * Default SAV/EAV mode is supported here with default codes |
| * SAV=0xff000080 & EAV=0xff00009d. |
| * With DCMI this means LSC=SAV=0x80 & LEC=EAV=0x9d. |
| */ |
| if (dcmi->bus_type == V4L2_MBUS_BT656) { |
| val |= CR_ESS; |
| |
| /* Unmask all codes */ |
| reg_write(dcmi->regs, DCMI_ESUR, 0xffffffff);/* FEC:LEC:LSC:FSC */ |
| |
| /* Trig on LSC=0x80 & LEC=0x9d codes, ignore FSC and FEC */ |
| reg_write(dcmi->regs, DCMI_ESCR, 0xff9d80ff);/* FEC:LEC:LSC:FSC */ |
| } |
| |
| reg_write(dcmi->regs, DCMI_CR, val); |
| |
| /* Set crop */ |
| if (dcmi->do_crop) |
| dcmi_set_crop(dcmi); |
| |
| /* Enable jpeg capture */ |
| if (dcmi->sd_format->fourcc == V4L2_PIX_FMT_JPEG) |
| reg_set(dcmi->regs, DCMI_CR, CR_CM);/* Snapshot mode */ |
| |
| /* Enable dcmi */ |
| reg_set(dcmi->regs, DCMI_CR, CR_ENABLE); |
| |
| dcmi->sequence = 0; |
| dcmi->errors_count = 0; |
| dcmi->overrun_count = 0; |
| dcmi->buffers_count = 0; |
| |
| /* |
| * Start transfer if at least one buffer has been queued, |
| * otherwise transfer is deferred at buffer queueing |
| */ |
| if (list_empty(&dcmi->buffers)) { |
| dev_dbg(dcmi->dev, "Start streaming is deferred to next buffer queueing\n"); |
| dcmi->state = WAIT_FOR_BUFFER; |
| spin_unlock_irq(&dcmi->irqlock); |
| return 0; |
| } |
| |
| buf = list_entry(dcmi->buffers.next, struct dcmi_buf, list); |
| dcmi->active = buf; |
| |
| dcmi->state = RUNNING; |
| |
| dev_dbg(dcmi->dev, "Start streaming, starting capture\n"); |
| |
| spin_unlock_irq(&dcmi->irqlock); |
| ret = dcmi_start_capture(dcmi, buf); |
| if (ret) { |
| dev_err(dcmi->dev, "%s: Start streaming failed, cannot start capture\n", |
| __func__); |
| goto err_pipeline_stop; |
| } |
| |
| /* Enable interruptions */ |
| if (dcmi->sd_format->fourcc == V4L2_PIX_FMT_JPEG) |
| reg_set(dcmi->regs, DCMI_IER, IT_FRAME | IT_OVR | IT_ERR); |
| else |
| reg_set(dcmi->regs, DCMI_IER, IT_OVR | IT_ERR); |
| |
| return 0; |
| |
| err_pipeline_stop: |
| dcmi_pipeline_stop(dcmi); |
| |
| err_media_pipeline_stop: |
| media_pipeline_stop(&dcmi->vdev->entity); |
| |
| err_pm_put: |
| pm_runtime_put(dcmi->dev); |
| err_unlocked: |
| spin_lock_irq(&dcmi->irqlock); |
| /* |
| * Return all buffers to vb2 in QUEUED state. |
| * This will give ownership back to userspace |
| */ |
| list_for_each_entry_safe(buf, node, &dcmi->buffers, list) { |
| list_del_init(&buf->list); |
| vb2_buffer_done(&buf->vb.vb2_buf, VB2_BUF_STATE_QUEUED); |
| } |
| dcmi->active = NULL; |
| spin_unlock_irq(&dcmi->irqlock); |
| |
| return ret; |
| } |
| |
| static void dcmi_stop_streaming(struct vb2_queue *vq) |
| { |
| struct stm32_dcmi *dcmi = vb2_get_drv_priv(vq); |
| struct dcmi_buf *buf, *node; |
| |
| dcmi_pipeline_stop(dcmi); |
| |
| media_pipeline_stop(&dcmi->vdev->entity); |
| |
| spin_lock_irq(&dcmi->irqlock); |
| |
| /* Disable interruptions */ |
| reg_clear(dcmi->regs, DCMI_IER, IT_FRAME | IT_OVR | IT_ERR); |
| |
| /* Disable DCMI */ |
| reg_clear(dcmi->regs, DCMI_CR, CR_ENABLE); |
| |
| /* Return all queued buffers to vb2 in ERROR state */ |
| list_for_each_entry_safe(buf, node, &dcmi->buffers, list) { |
| list_del_init(&buf->list); |
| vb2_buffer_done(&buf->vb.vb2_buf, VB2_BUF_STATE_ERROR); |
| } |
| |
| dcmi->active = NULL; |
| dcmi->state = STOPPED; |
| |
| spin_unlock_irq(&dcmi->irqlock); |
| |
| /* Stop all pending DMA operations */ |
| mutex_lock(&dcmi->dma_lock); |
| dmaengine_terminate_sync(dcmi->dma_chan); |
| mutex_unlock(&dcmi->dma_lock); |
| |
| pm_runtime_put(dcmi->dev); |
| |
| if (dcmi->errors_count) |
| dev_warn(dcmi->dev, "Some errors found while streaming: errors=%d (overrun=%d), buffers=%d\n", |
| dcmi->errors_count, dcmi->overrun_count, |
| dcmi->buffers_count); |
| dev_dbg(dcmi->dev, "Stop streaming, errors=%d (overrun=%d), buffers=%d\n", |
| dcmi->errors_count, dcmi->overrun_count, |
| dcmi->buffers_count); |
| } |
| |
| static const struct vb2_ops dcmi_video_qops = { |
| .queue_setup = dcmi_queue_setup, |
| .buf_init = dcmi_buf_init, |
| .buf_prepare = dcmi_buf_prepare, |
| .buf_queue = dcmi_buf_queue, |
| .start_streaming = dcmi_start_streaming, |
| .stop_streaming = dcmi_stop_streaming, |
| .wait_prepare = vb2_ops_wait_prepare, |
| .wait_finish = vb2_ops_wait_finish, |
| }; |
| |
| static int dcmi_g_fmt_vid_cap(struct file *file, void *priv, |
| struct v4l2_format *fmt) |
| { |
| struct stm32_dcmi *dcmi = video_drvdata(file); |
| |
| *fmt = dcmi->fmt; |
| |
| return 0; |
| } |
| |
| static const struct dcmi_format *find_format_by_fourcc(struct stm32_dcmi *dcmi, |
| unsigned int fourcc) |
| { |
| unsigned int num_formats = dcmi->num_of_sd_formats; |
| const struct dcmi_format *fmt; |
| unsigned int i; |
| |
| for (i = 0; i < num_formats; i++) { |
| fmt = dcmi->sd_formats[i]; |
| if (fmt->fourcc == fourcc) |
| return fmt; |
| } |
| |
| return NULL; |
| } |
| |
| static void __find_outer_frame_size(struct stm32_dcmi *dcmi, |
| struct v4l2_pix_format *pix, |
| struct dcmi_framesize *framesize) |
| { |
| struct dcmi_framesize *match = NULL; |
| unsigned int i; |
| unsigned int min_err = UINT_MAX; |
| |
| for (i = 0; i < dcmi->num_of_sd_framesizes; i++) { |
| struct dcmi_framesize *fsize = &dcmi->sd_framesizes[i]; |
| int w_err = (fsize->width - pix->width); |
| int h_err = (fsize->height - pix->height); |
| int err = w_err + h_err; |
| |
| if (w_err >= 0 && h_err >= 0 && err < min_err) { |
| min_err = err; |
| match = fsize; |
| } |
| } |
| if (!match) |
| match = &dcmi->sd_framesizes[0]; |
| |
| *framesize = *match; |
| } |
| |
| static int dcmi_try_fmt(struct stm32_dcmi *dcmi, struct v4l2_format *f, |
| const struct dcmi_format **sd_format, |
| struct dcmi_framesize *sd_framesize) |
| { |
| const struct dcmi_format *sd_fmt; |
| struct dcmi_framesize sd_fsize; |
| struct v4l2_pix_format *pix = &f->fmt.pix; |
| struct v4l2_subdev_pad_config pad_cfg; |
| struct v4l2_subdev_state pad_state = { |
| .pads = &pad_cfg |
| }; |
| struct v4l2_subdev_format format = { |
| .which = V4L2_SUBDEV_FORMAT_TRY, |
| }; |
| bool do_crop; |
| int ret; |
| |
| sd_fmt = find_format_by_fourcc(dcmi, pix->pixelformat); |
| if (!sd_fmt) { |
| if (!dcmi->num_of_sd_formats) |
| return -ENODATA; |
| |
| sd_fmt = dcmi->sd_formats[dcmi->num_of_sd_formats - 1]; |
| pix->pixelformat = sd_fmt->fourcc; |
| } |
| |
| /* Limit to hardware capabilities */ |
| pix->width = clamp(pix->width, MIN_WIDTH, MAX_WIDTH); |
| pix->height = clamp(pix->height, MIN_HEIGHT, MAX_HEIGHT); |
| |
| /* No crop if JPEG is requested */ |
| do_crop = dcmi->do_crop && (pix->pixelformat != V4L2_PIX_FMT_JPEG); |
| |
| if (do_crop && dcmi->num_of_sd_framesizes) { |
| struct dcmi_framesize outer_sd_fsize; |
| /* |
| * If crop is requested and sensor have discrete frame sizes, |
| * select the frame size that is just larger than request |
| */ |
| __find_outer_frame_size(dcmi, pix, &outer_sd_fsize); |
| pix->width = outer_sd_fsize.width; |
| pix->height = outer_sd_fsize.height; |
| } |
| |
| v4l2_fill_mbus_format(&format.format, pix, sd_fmt->mbus_code); |
| ret = v4l2_subdev_call(dcmi->source, pad, set_fmt, |
| &pad_state, &format); |
| if (ret < 0) |
| return ret; |
| |
| /* Update pix regarding to what sensor can do */ |
| v4l2_fill_pix_format(pix, &format.format); |
| |
| /* Save resolution that sensor can actually do */ |
| sd_fsize.width = pix->width; |
| sd_fsize.height = pix->height; |
| |
| if (do_crop) { |
| struct v4l2_rect c = dcmi->crop; |
| struct v4l2_rect max_rect; |
| |
| /* |
| * Adjust crop by making the intersection between |
| * format resolution request and crop request |
| */ |
| max_rect.top = 0; |
| max_rect.left = 0; |
| max_rect.width = pix->width; |
| max_rect.height = pix->height; |
| v4l2_rect_map_inside(&c, &max_rect); |
| c.top = clamp_t(s32, c.top, 0, pix->height - c.height); |
| c.left = clamp_t(s32, c.left, 0, pix->width - c.width); |
| dcmi->crop = c; |
| |
| /* Adjust format resolution request to crop */ |
| pix->width = dcmi->crop.width; |
| pix->height = dcmi->crop.height; |
| } |
| |
| pix->field = V4L2_FIELD_NONE; |
| pix->bytesperline = pix->width * sd_fmt->bpp; |
| pix->sizeimage = pix->bytesperline * pix->height; |
| |
| if (sd_format) |
| *sd_format = sd_fmt; |
| if (sd_framesize) |
| *sd_framesize = sd_fsize; |
| |
| return 0; |
| } |
| |
| static int dcmi_set_fmt(struct stm32_dcmi *dcmi, struct v4l2_format *f) |
| { |
| struct v4l2_subdev_format format = { |
| .which = V4L2_SUBDEV_FORMAT_ACTIVE, |
| }; |
| const struct dcmi_format *sd_format; |
| struct dcmi_framesize sd_framesize; |
| struct v4l2_mbus_framefmt *mf = &format.format; |
| struct v4l2_pix_format *pix = &f->fmt.pix; |
| int ret; |
| |
| /* |
| * Try format, fmt.width/height could have been changed |
| * to match sensor capability or crop request |
| * sd_format & sd_framesize will contain what subdev |
| * can do for this request. |
| */ |
| ret = dcmi_try_fmt(dcmi, f, &sd_format, &sd_framesize); |
| if (ret) |
| return ret; |
| |
| /* Disable crop if JPEG is requested or BT656 bus is selected */ |
| if (pix->pixelformat == V4L2_PIX_FMT_JPEG && |
| dcmi->bus_type != V4L2_MBUS_BT656) |
| dcmi->do_crop = false; |
| |
| /* pix to mbus format */ |
| v4l2_fill_mbus_format(mf, pix, |
| sd_format->mbus_code); |
| mf->width = sd_framesize.width; |
| mf->height = sd_framesize.height; |
| |
| ret = dcmi_pipeline_s_fmt(dcmi, NULL, &format); |
| if (ret < 0) |
| return ret; |
| |
| dev_dbg(dcmi->dev, "Sensor format set to 0x%x %ux%u\n", |
| mf->code, mf->width, mf->height); |
| dev_dbg(dcmi->dev, "Buffer format set to %4.4s %ux%u\n", |
| (char *)&pix->pixelformat, |
| pix->width, pix->height); |
| |
| dcmi->fmt = *f; |
| dcmi->sd_format = sd_format; |
| dcmi->sd_framesize = sd_framesize; |
| |
| return 0; |
| } |
| |
| static int dcmi_s_fmt_vid_cap(struct file *file, void *priv, |
| struct v4l2_format *f) |
| { |
| struct stm32_dcmi *dcmi = video_drvdata(file); |
| |
| if (vb2_is_streaming(&dcmi->queue)) |
| return -EBUSY; |
| |
| return dcmi_set_fmt(dcmi, f); |
| } |
| |
| static int dcmi_try_fmt_vid_cap(struct file *file, void *priv, |
| struct v4l2_format *f) |
| { |
| struct stm32_dcmi *dcmi = video_drvdata(file); |
| |
| return dcmi_try_fmt(dcmi, f, NULL, NULL); |
| } |
| |
| static int dcmi_enum_fmt_vid_cap(struct file *file, void *priv, |
| struct v4l2_fmtdesc *f) |
| { |
| struct stm32_dcmi *dcmi = video_drvdata(file); |
| |
| if (f->index >= dcmi->num_of_sd_formats) |
| return -EINVAL; |
| |
| f->pixelformat = dcmi->sd_formats[f->index]->fourcc; |
| return 0; |
| } |
| |
| static int dcmi_get_sensor_format(struct stm32_dcmi *dcmi, |
| struct v4l2_pix_format *pix) |
| { |
| struct v4l2_subdev_format fmt = { |
| .which = V4L2_SUBDEV_FORMAT_ACTIVE, |
| }; |
| int ret; |
| |
| ret = v4l2_subdev_call(dcmi->source, pad, get_fmt, NULL, &fmt); |
| if (ret) |
| return ret; |
| |
| v4l2_fill_pix_format(pix, &fmt.format); |
| |
| return 0; |
| } |
| |
| static int dcmi_set_sensor_format(struct stm32_dcmi *dcmi, |
| struct v4l2_pix_format *pix) |
| { |
| const struct dcmi_format *sd_fmt; |
| struct v4l2_subdev_format format = { |
| .which = V4L2_SUBDEV_FORMAT_TRY, |
| }; |
| struct v4l2_subdev_pad_config pad_cfg; |
| struct v4l2_subdev_state pad_state = { |
| .pads = &pad_cfg |
| }; |
| int ret; |
| |
| sd_fmt = find_format_by_fourcc(dcmi, pix->pixelformat); |
| if (!sd_fmt) { |
| if (!dcmi->num_of_sd_formats) |
| return -ENODATA; |
| |
| sd_fmt = dcmi->sd_formats[dcmi->num_of_sd_formats - 1]; |
| pix->pixelformat = sd_fmt->fourcc; |
| } |
| |
| v4l2_fill_mbus_format(&format.format, pix, sd_fmt->mbus_code); |
| ret = v4l2_subdev_call(dcmi->source, pad, set_fmt, |
| &pad_state, &format); |
| if (ret < 0) |
| return ret; |
| |
| return 0; |
| } |
| |
| static int dcmi_get_sensor_bounds(struct stm32_dcmi *dcmi, |
| struct v4l2_rect *r) |
| { |
| struct v4l2_subdev_selection bounds = { |
| .which = V4L2_SUBDEV_FORMAT_ACTIVE, |
| .target = V4L2_SEL_TGT_CROP_BOUNDS, |
| }; |
| unsigned int max_width, max_height, max_pixsize; |
| struct v4l2_pix_format pix; |
| unsigned int i; |
| int ret; |
| |
| /* |
| * Get sensor bounds first |
| */ |
| ret = v4l2_subdev_call(dcmi->source, pad, get_selection, |
| NULL, &bounds); |
| if (!ret) |
| *r = bounds.r; |
| if (ret != -ENOIOCTLCMD) |
| return ret; |
| |
| /* |
| * If selection is not implemented, |
| * fallback by enumerating sensor frame sizes |
| * and take the largest one |
| */ |
| max_width = 0; |
| max_height = 0; |
| max_pixsize = 0; |
| for (i = 0; i < dcmi->num_of_sd_framesizes; i++) { |
| struct dcmi_framesize *fsize = &dcmi->sd_framesizes[i]; |
| unsigned int pixsize = fsize->width * fsize->height; |
| |
| if (pixsize > max_pixsize) { |
| max_pixsize = pixsize; |
| max_width = fsize->width; |
| max_height = fsize->height; |
| } |
| } |
| if (max_pixsize > 0) { |
| r->top = 0; |
| r->left = 0; |
| r->width = max_width; |
| r->height = max_height; |
| return 0; |
| } |
| |
| /* |
| * If frame sizes enumeration is not implemented, |
| * fallback by getting current sensor frame size |
| */ |
| ret = dcmi_get_sensor_format(dcmi, &pix); |
| if (ret) |
| return ret; |
| |
| r->top = 0; |
| r->left = 0; |
| r->width = pix.width; |
| r->height = pix.height; |
| |
| return 0; |
| } |
| |
| static int dcmi_g_selection(struct file *file, void *fh, |
| struct v4l2_selection *s) |
| { |
| struct stm32_dcmi *dcmi = video_drvdata(file); |
| |
| if (s->type != V4L2_BUF_TYPE_VIDEO_CAPTURE) |
| return -EINVAL; |
| |
| switch (s->target) { |
| case V4L2_SEL_TGT_CROP_DEFAULT: |
| case V4L2_SEL_TGT_CROP_BOUNDS: |
| s->r = dcmi->sd_bounds; |
| return 0; |
| case V4L2_SEL_TGT_CROP: |
| if (dcmi->do_crop) { |
| s->r = dcmi->crop; |
| } else { |
| s->r.top = 0; |
| s->r.left = 0; |
| s->r.width = dcmi->fmt.fmt.pix.width; |
| s->r.height = dcmi->fmt.fmt.pix.height; |
| } |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| return 0; |
| } |
| |
| static int dcmi_s_selection(struct file *file, void *priv, |
| struct v4l2_selection *s) |
| { |
| struct stm32_dcmi *dcmi = video_drvdata(file); |
| struct v4l2_rect r = s->r; |
| struct v4l2_rect max_rect; |
| struct v4l2_pix_format pix; |
| |
| if (s->type != V4L2_BUF_TYPE_VIDEO_CAPTURE || |
| s->target != V4L2_SEL_TGT_CROP) |
| return -EINVAL; |
| |
| /* Reset sensor resolution to max resolution */ |
| pix.pixelformat = dcmi->fmt.fmt.pix.pixelformat; |
| pix.width = dcmi->sd_bounds.width; |
| pix.height = dcmi->sd_bounds.height; |
| dcmi_set_sensor_format(dcmi, &pix); |
| |
| /* |
| * Make the intersection between |
| * sensor resolution |
| * and crop request |
| */ |
| max_rect.top = 0; |
| max_rect.left = 0; |
| max_rect.width = pix.width; |
| max_rect.height = pix.height; |
| v4l2_rect_map_inside(&r, &max_rect); |
| r.top = clamp_t(s32, r.top, 0, pix.height - r.height); |
| r.left = clamp_t(s32, r.left, 0, pix.width - r.width); |
| |
| if (!(r.top == dcmi->sd_bounds.top && |
| r.left == dcmi->sd_bounds.left && |
| r.width == dcmi->sd_bounds.width && |
| r.height == dcmi->sd_bounds.height)) { |
| /* Crop if request is different than sensor resolution */ |
| dcmi->do_crop = true; |
| dcmi->crop = r; |
| dev_dbg(dcmi->dev, "s_selection: crop %ux%u@(%u,%u) from %ux%u\n", |
| r.width, r.height, r.left, r.top, |
| pix.width, pix.height); |
| } else { |
| /* Disable crop */ |
| dcmi->do_crop = false; |
| dev_dbg(dcmi->dev, "s_selection: crop is disabled\n"); |
| } |
| |
| s->r = r; |
| return 0; |
| } |
| |
| static int dcmi_querycap(struct file *file, void *priv, |
| struct v4l2_capability *cap) |
| { |
| strscpy(cap->driver, DRV_NAME, sizeof(cap->driver)); |
| strscpy(cap->card, "STM32 Camera Memory Interface", |
| sizeof(cap->card)); |
| strscpy(cap->bus_info, "platform:dcmi", sizeof(cap->bus_info)); |
| return 0; |
| } |
| |
| static int dcmi_enum_input(struct file *file, void *priv, |
| struct v4l2_input *i) |
| { |
| if (i->index != 0) |
| return -EINVAL; |
| |
| i->type = V4L2_INPUT_TYPE_CAMERA; |
| strscpy(i->name, "Camera", sizeof(i->name)); |
| return 0; |
| } |
| |
| static int dcmi_g_input(struct file *file, void *priv, unsigned int *i) |
| { |
| *i = 0; |
| return 0; |
| } |
| |
| static int dcmi_s_input(struct file *file, void *priv, unsigned int i) |
| { |
| if (i > 0) |
| return -EINVAL; |
| return 0; |
| } |
| |
| static int dcmi_enum_framesizes(struct file *file, void *fh, |
| struct v4l2_frmsizeenum *fsize) |
| { |
| struct stm32_dcmi *dcmi = video_drvdata(file); |
| const struct dcmi_format *sd_fmt; |
| struct v4l2_subdev_frame_size_enum fse = { |
| .index = fsize->index, |
| .which = V4L2_SUBDEV_FORMAT_ACTIVE, |
| }; |
| int ret; |
| |
| sd_fmt = find_format_by_fourcc(dcmi, fsize->pixel_format); |
| if (!sd_fmt) |
| return -EINVAL; |
| |
| fse.code = sd_fmt->mbus_code; |
| |
| ret = v4l2_subdev_call(dcmi->source, pad, enum_frame_size, |
| NULL, &fse); |
| if (ret) |
| return ret; |
| |
| fsize->type = V4L2_FRMSIZE_TYPE_DISCRETE; |
| fsize->discrete.width = fse.max_width; |
| fsize->discrete.height = fse.max_height; |
| |
| return 0; |
| } |
| |
| static int dcmi_g_parm(struct file *file, void *priv, |
| struct v4l2_streamparm *p) |
| { |
| struct stm32_dcmi *dcmi = video_drvdata(file); |
| |
| return v4l2_g_parm_cap(video_devdata(file), dcmi->source, p); |
| } |
| |
| static int dcmi_s_parm(struct file *file, void *priv, |
| struct v4l2_streamparm *p) |
| { |
| struct stm32_dcmi *dcmi = video_drvdata(file); |
| |
| return v4l2_s_parm_cap(video_devdata(file), dcmi->source, p); |
| } |
| |
| static int dcmi_enum_frameintervals(struct file *file, void *fh, |
| struct v4l2_frmivalenum *fival) |
| { |
| struct stm32_dcmi *dcmi = video_drvdata(file); |
| const struct dcmi_format *sd_fmt; |
| struct v4l2_subdev_frame_interval_enum fie = { |
| .index = fival->index, |
| .width = fival->width, |
| .height = fival->height, |
| .which = V4L2_SUBDEV_FORMAT_ACTIVE, |
| }; |
| int ret; |
| |
| sd_fmt = find_format_by_fourcc(dcmi, fival->pixel_format); |
| if (!sd_fmt) |
| return -EINVAL; |
| |
| fie.code = sd_fmt->mbus_code; |
| |
| ret = v4l2_subdev_call(dcmi->source, pad, |
| enum_frame_interval, NULL, &fie); |
| if (ret) |
| return ret; |
| |
| fival->type = V4L2_FRMIVAL_TYPE_DISCRETE; |
| fival->discrete = fie.interval; |
| |
| return 0; |
| } |
| |
| static const struct of_device_id stm32_dcmi_of_match[] = { |
| { .compatible = "st,stm32-dcmi"}, |
| { /* end node */ }, |
| }; |
| MODULE_DEVICE_TABLE(of, stm32_dcmi_of_match); |
| |
| static int dcmi_open(struct file *file) |
| { |
| struct stm32_dcmi *dcmi = video_drvdata(file); |
| struct v4l2_subdev *sd = dcmi->source; |
| int ret; |
| |
| if (mutex_lock_interruptible(&dcmi->lock)) |
| return -ERESTARTSYS; |
| |
| ret = v4l2_fh_open(file); |
| if (ret < 0) |
| goto unlock; |
| |
| if (!v4l2_fh_is_singular_file(file)) |
| goto fh_rel; |
| |
| ret = v4l2_subdev_call(sd, core, s_power, 1); |
| if (ret < 0 && ret != -ENOIOCTLCMD) |
| goto fh_rel; |
| |
| ret = dcmi_set_fmt(dcmi, &dcmi->fmt); |
| if (ret) |
| v4l2_subdev_call(sd, core, s_power, 0); |
| fh_rel: |
| if (ret) |
| v4l2_fh_release(file); |
| unlock: |
| mutex_unlock(&dcmi->lock); |
| return ret; |
| } |
| |
| static int dcmi_release(struct file *file) |
| { |
| struct stm32_dcmi *dcmi = video_drvdata(file); |
| struct v4l2_subdev *sd = dcmi->source; |
| bool fh_singular; |
| int ret; |
| |
| mutex_lock(&dcmi->lock); |
| |
| fh_singular = v4l2_fh_is_singular_file(file); |
| |
| ret = _vb2_fop_release(file, NULL); |
| |
| if (fh_singular) |
| v4l2_subdev_call(sd, core, s_power, 0); |
| |
| mutex_unlock(&dcmi->lock); |
| |
| return ret; |
| } |
| |
| static const struct v4l2_ioctl_ops dcmi_ioctl_ops = { |
| .vidioc_querycap = dcmi_querycap, |
| |
| .vidioc_try_fmt_vid_cap = dcmi_try_fmt_vid_cap, |
| .vidioc_g_fmt_vid_cap = dcmi_g_fmt_vid_cap, |
| .vidioc_s_fmt_vid_cap = dcmi_s_fmt_vid_cap, |
| .vidioc_enum_fmt_vid_cap = dcmi_enum_fmt_vid_cap, |
| .vidioc_g_selection = dcmi_g_selection, |
| .vidioc_s_selection = dcmi_s_selection, |
| |
| .vidioc_enum_input = dcmi_enum_input, |
| .vidioc_g_input = dcmi_g_input, |
| .vidioc_s_input = dcmi_s_input, |
| |
| .vidioc_g_parm = dcmi_g_parm, |
| .vidioc_s_parm = dcmi_s_parm, |
| |
| .vidioc_enum_framesizes = dcmi_enum_framesizes, |
| .vidioc_enum_frameintervals = dcmi_enum_frameintervals, |
| |
| .vidioc_reqbufs = vb2_ioctl_reqbufs, |
| .vidioc_create_bufs = vb2_ioctl_create_bufs, |
| .vidioc_querybuf = vb2_ioctl_querybuf, |
| .vidioc_qbuf = vb2_ioctl_qbuf, |
| .vidioc_dqbuf = vb2_ioctl_dqbuf, |
| .vidioc_expbuf = vb2_ioctl_expbuf, |
| .vidioc_prepare_buf = vb2_ioctl_prepare_buf, |
| .vidioc_streamon = vb2_ioctl_streamon, |
| .vidioc_streamoff = vb2_ioctl_streamoff, |
| |
| .vidioc_log_status = v4l2_ctrl_log_status, |
| .vidioc_subscribe_event = v4l2_ctrl_subscribe_event, |
| .vidioc_unsubscribe_event = v4l2_event_unsubscribe, |
| }; |
| |
| static const struct v4l2_file_operations dcmi_fops = { |
| .owner = THIS_MODULE, |
| .unlocked_ioctl = video_ioctl2, |
| .open = dcmi_open, |
| .release = dcmi_release, |
| .poll = vb2_fop_poll, |
| .mmap = vb2_fop_mmap, |
| #ifndef CONFIG_MMU |
| .get_unmapped_area = vb2_fop_get_unmapped_area, |
| #endif |
| .read = vb2_fop_read, |
| }; |
| |
| static int dcmi_set_default_fmt(struct stm32_dcmi *dcmi) |
| { |
| struct v4l2_format f = { |
| .type = V4L2_BUF_TYPE_VIDEO_CAPTURE, |
| .fmt.pix = { |
| .width = CIF_WIDTH, |
| .height = CIF_HEIGHT, |
| .field = V4L2_FIELD_NONE, |
| .pixelformat = dcmi->sd_formats[0]->fourcc, |
| }, |
| }; |
| int ret; |
| |
| ret = dcmi_try_fmt(dcmi, &f, NULL, NULL); |
| if (ret) |
| return ret; |
| dcmi->sd_format = dcmi->sd_formats[0]; |
| dcmi->fmt = f; |
| return 0; |
| } |
| |
| /* |
| * FIXME: For the time being we only support subdevices |
| * which expose RGB & YUV "parallel form" mbus code (_2X8). |
| * Nevertheless, this allows to support serial source subdevices |
| * and serial to parallel bridges which conform to this. |
| */ |
| static const struct dcmi_format dcmi_formats[] = { |
| { |
| .fourcc = V4L2_PIX_FMT_RGB565, |
| .mbus_code = MEDIA_BUS_FMT_RGB565_2X8_LE, |
| .bpp = 2, |
| }, { |
| .fourcc = V4L2_PIX_FMT_YUYV, |
| .mbus_code = MEDIA_BUS_FMT_YUYV8_2X8, |
| .bpp = 2, |
| }, { |
| .fourcc = V4L2_PIX_FMT_UYVY, |
| .mbus_code = MEDIA_BUS_FMT_UYVY8_2X8, |
| .bpp = 2, |
| }, { |
| .fourcc = V4L2_PIX_FMT_JPEG, |
| .mbus_code = MEDIA_BUS_FMT_JPEG_1X8, |
| .bpp = 1, |
| }, { |
| .fourcc = V4L2_PIX_FMT_SBGGR8, |
| .mbus_code = MEDIA_BUS_FMT_SBGGR8_1X8, |
| .bpp = 1, |
| }, { |
| .fourcc = V4L2_PIX_FMT_SGBRG8, |
| .mbus_code = MEDIA_BUS_FMT_SGBRG8_1X8, |
| .bpp = 1, |
| }, { |
| .fourcc = V4L2_PIX_FMT_SGRBG8, |
| .mbus_code = MEDIA_BUS_FMT_SGRBG8_1X8, |
| .bpp = 1, |
| }, { |
| .fourcc = V4L2_PIX_FMT_SRGGB8, |
| .mbus_code = MEDIA_BUS_FMT_SRGGB8_1X8, |
| .bpp = 1, |
| }, |
| }; |
| |
| static int dcmi_formats_init(struct stm32_dcmi *dcmi) |
| { |
| const struct dcmi_format *sd_fmts[ARRAY_SIZE(dcmi_formats)]; |
| unsigned int num_fmts = 0, i, j; |
| struct v4l2_subdev *subdev = dcmi->source; |
| struct v4l2_subdev_mbus_code_enum mbus_code = { |
| .which = V4L2_SUBDEV_FORMAT_ACTIVE, |
| }; |
| |
| while (!v4l2_subdev_call(subdev, pad, enum_mbus_code, |
| NULL, &mbus_code)) { |
| for (i = 0; i < ARRAY_SIZE(dcmi_formats); i++) { |
| if (dcmi_formats[i].mbus_code != mbus_code.code) |
| continue; |
| |
| /* Exclude JPEG if BT656 bus is selected */ |
| if (dcmi_formats[i].fourcc == V4L2_PIX_FMT_JPEG && |
| dcmi->bus_type == V4L2_MBUS_BT656) |
| continue; |
| |
| /* Code supported, have we got this fourcc yet? */ |
| for (j = 0; j < num_fmts; j++) |
| if (sd_fmts[j]->fourcc == |
| dcmi_formats[i].fourcc) { |
| /* Already available */ |
| dev_dbg(dcmi->dev, "Skipping fourcc/code: %4.4s/0x%x\n", |
| (char *)&sd_fmts[j]->fourcc, |
| mbus_code.code); |
| break; |
| } |
| if (j == num_fmts) { |
| /* New */ |
| sd_fmts[num_fmts++] = dcmi_formats + i; |
| dev_dbg(dcmi->dev, "Supported fourcc/code: %4.4s/0x%x\n", |
| (char *)&sd_fmts[num_fmts - 1]->fourcc, |
| sd_fmts[num_fmts - 1]->mbus_code); |
| } |
| } |
| mbus_code.index++; |
| } |
| |
| if (!num_fmts) |
| return -ENXIO; |
| |
| dcmi->num_of_sd_formats = num_fmts; |
| dcmi->sd_formats = devm_kcalloc(dcmi->dev, |
| num_fmts, sizeof(struct dcmi_format *), |
| GFP_KERNEL); |
| if (!dcmi->sd_formats) { |
| dev_err(dcmi->dev, "Could not allocate memory\n"); |
| return -ENOMEM; |
| } |
| |
| memcpy(dcmi->sd_formats, sd_fmts, |
| num_fmts * sizeof(struct dcmi_format *)); |
| dcmi->sd_format = dcmi->sd_formats[0]; |
| |
| return 0; |
| } |
| |
| static int dcmi_framesizes_init(struct stm32_dcmi *dcmi) |
| { |
| unsigned int num_fsize = 0; |
| struct v4l2_subdev *subdev = dcmi->source; |
| struct v4l2_subdev_frame_size_enum fse = { |
| .which = V4L2_SUBDEV_FORMAT_ACTIVE, |
| .code = dcmi->sd_format->mbus_code, |
| }; |
| unsigned int ret; |
| unsigned int i; |
| |
| /* Allocate discrete framesizes array */ |
| while (!v4l2_subdev_call(subdev, pad, enum_frame_size, |
| NULL, &fse)) |
| fse.index++; |
| |
| num_fsize = fse.index; |
| if (!num_fsize) |
| return 0; |
| |
| dcmi->num_of_sd_framesizes = num_fsize; |
| dcmi->sd_framesizes = devm_kcalloc(dcmi->dev, num_fsize, |
| sizeof(struct dcmi_framesize), |
| GFP_KERNEL); |
| if (!dcmi->sd_framesizes) { |
| dev_err(dcmi->dev, "Could not allocate memory\n"); |
| return -ENOMEM; |
| } |
| |
| /* Fill array with sensor supported framesizes */ |
| dev_dbg(dcmi->dev, "Sensor supports %u frame sizes:\n", num_fsize); |
| for (i = 0; i < dcmi->num_of_sd_framesizes; i++) { |
| fse.index = i; |
| ret = v4l2_subdev_call(subdev, pad, enum_frame_size, |
| NULL, &fse); |
| if (ret) |
| return ret; |
| dcmi->sd_framesizes[fse.index].width = fse.max_width; |
| dcmi->sd_framesizes[fse.index].height = fse.max_height; |
| dev_dbg(dcmi->dev, "%ux%u\n", fse.max_width, fse.max_height); |
| } |
| |
| return 0; |
| } |
| |
| static int dcmi_graph_notify_complete(struct v4l2_async_notifier *notifier) |
| { |
| struct stm32_dcmi *dcmi = notifier_to_dcmi(notifier); |
| int ret; |
| |
| /* |
| * Now that the graph is complete, |
| * we search for the source subdevice |
| * in order to expose it through V4L2 interface |
| */ |
| dcmi->source = media_entity_to_v4l2_subdev(dcmi_find_source(dcmi)); |
| if (!dcmi->source) { |
| dev_err(dcmi->dev, "Source subdevice not found\n"); |
| return -ENODEV; |
| } |
| |
| dcmi->vdev->ctrl_handler = dcmi->source->ctrl_handler; |
| |
| ret = dcmi_formats_init(dcmi); |
| if (ret) { |
| dev_err(dcmi->dev, "No supported mediabus format found\n"); |
| return ret; |
| } |
| |
| ret = dcmi_framesizes_init(dcmi); |
| if (ret) { |
| dev_err(dcmi->dev, "Could not initialize framesizes\n"); |
| return ret; |
| } |
| |
| ret = dcmi_get_sensor_bounds(dcmi, &dcmi->sd_bounds); |
| if (ret) { |
| dev_err(dcmi->dev, "Could not get sensor bounds\n"); |
| return ret; |
| } |
| |
| ret = dcmi_set_default_fmt(dcmi); |
| if (ret) { |
| dev_err(dcmi->dev, "Could not set default format\n"); |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static void dcmi_graph_notify_unbind(struct v4l2_async_notifier *notifier, |
| struct v4l2_subdev *sd, |
| struct v4l2_async_subdev *asd) |
| { |
| struct stm32_dcmi *dcmi = notifier_to_dcmi(notifier); |
| |
| dev_dbg(dcmi->dev, "Removing %s\n", video_device_node_name(dcmi->vdev)); |
| |
| /* Checks internally if vdev has been init or not */ |
| video_unregister_device(dcmi->vdev); |
| } |
| |
| static int dcmi_graph_notify_bound(struct v4l2_async_notifier *notifier, |
| struct v4l2_subdev *subdev, |
| struct v4l2_async_subdev *asd) |
| { |
| struct stm32_dcmi *dcmi = notifier_to_dcmi(notifier); |
| unsigned int ret; |
| int src_pad; |
| |
| dev_dbg(dcmi->dev, "Subdev \"%s\" bound\n", subdev->name); |
| |
| /* |
| * Link this sub-device to DCMI, it could be |
| * a parallel camera sensor or a bridge |
| */ |
| src_pad = media_entity_get_fwnode_pad(&subdev->entity, |
| subdev->fwnode, |
| MEDIA_PAD_FL_SOURCE); |
| |
| ret = media_create_pad_link(&subdev->entity, src_pad, |
| &dcmi->vdev->entity, 0, |
| MEDIA_LNK_FL_IMMUTABLE | |
| MEDIA_LNK_FL_ENABLED); |
| if (ret) |
| dev_err(dcmi->dev, "Failed to create media pad link with subdev \"%s\"\n", |
| subdev->name); |
| else |
| dev_dbg(dcmi->dev, "DCMI is now linked to \"%s\"\n", |
| subdev->name); |
| |
| return ret; |
| } |
| |
| static const struct v4l2_async_notifier_operations dcmi_graph_notify_ops = { |
| .bound = dcmi_graph_notify_bound, |
| .unbind = dcmi_graph_notify_unbind, |
| .complete = dcmi_graph_notify_complete, |
| }; |
| |
| static int dcmi_graph_init(struct stm32_dcmi *dcmi) |
| { |
| struct v4l2_async_subdev *asd; |
| struct device_node *ep; |
| int ret; |
| |
| ep = of_graph_get_next_endpoint(dcmi->dev->of_node, NULL); |
| if (!ep) { |
| dev_err(dcmi->dev, "Failed to get next endpoint\n"); |
| return -EINVAL; |
| } |
| |
| v4l2_async_notifier_init(&dcmi->notifier); |
| |
| asd = v4l2_async_notifier_add_fwnode_remote_subdev( |
| &dcmi->notifier, of_fwnode_handle(ep), |
| struct v4l2_async_subdev); |
| |
| of_node_put(ep); |
| |
| if (IS_ERR(asd)) { |
| dev_err(dcmi->dev, "Failed to add subdev notifier\n"); |
| return PTR_ERR(asd); |
| } |
| |
| dcmi->notifier.ops = &dcmi_graph_notify_ops; |
| |
| ret = v4l2_async_notifier_register(&dcmi->v4l2_dev, &dcmi->notifier); |
| if (ret < 0) { |
| dev_err(dcmi->dev, "Failed to register notifier\n"); |
| v4l2_async_notifier_cleanup(&dcmi->notifier); |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static int dcmi_probe(struct platform_device *pdev) |
| { |
| struct device_node *np = pdev->dev.of_node; |
| const struct of_device_id *match = NULL; |
| struct v4l2_fwnode_endpoint ep = { .bus_type = 0 }; |
| struct stm32_dcmi *dcmi; |
| struct vb2_queue *q; |
| struct dma_chan *chan; |
| struct clk *mclk; |
| int irq; |
| int ret = 0; |
| |
| match = of_match_device(of_match_ptr(stm32_dcmi_of_match), &pdev->dev); |
| if (!match) { |
| dev_err(&pdev->dev, "Could not find a match in devicetree\n"); |
| return -ENODEV; |
| } |
| |
| dcmi = devm_kzalloc(&pdev->dev, sizeof(struct stm32_dcmi), GFP_KERNEL); |
| if (!dcmi) |
| return -ENOMEM; |
| |
| dcmi->rstc = devm_reset_control_get_exclusive(&pdev->dev, NULL); |
| if (IS_ERR(dcmi->rstc)) { |
| if (PTR_ERR(dcmi->rstc) != -EPROBE_DEFER) |
| dev_err(&pdev->dev, "Could not get reset control\n"); |
| |
| return PTR_ERR(dcmi->rstc); |
| } |
| |
| /* Get bus characteristics from devicetree */ |
| np = of_graph_get_next_endpoint(np, NULL); |
| if (!np) { |
| dev_err(&pdev->dev, "Could not find the endpoint\n"); |
| return -ENODEV; |
| } |
| |
| ret = v4l2_fwnode_endpoint_parse(of_fwnode_handle(np), &ep); |
| of_node_put(np); |
| if (ret) { |
| dev_err(&pdev->dev, "Could not parse the endpoint\n"); |
| return ret; |
| } |
| |
| if (ep.bus_type == V4L2_MBUS_CSI2_DPHY) { |
| dev_err(&pdev->dev, "CSI bus not supported\n"); |
| return -ENODEV; |
| } |
| |
| if (ep.bus_type == V4L2_MBUS_BT656 && |
| ep.bus.parallel.bus_width != 8) { |
| dev_err(&pdev->dev, "BT656 bus conflicts with %u bits bus width (8 bits required)\n", |
| ep.bus.parallel.bus_width); |
| return -ENODEV; |
| } |
| |
| dcmi->bus.flags = ep.bus.parallel.flags; |
| dcmi->bus.bus_width = ep.bus.parallel.bus_width; |
| dcmi->bus.data_shift = ep.bus.parallel.data_shift; |
| dcmi->bus_type = ep.bus_type; |
| |
| irq = platform_get_irq(pdev, 0); |
| if (irq <= 0) |
| return irq ? irq : -ENXIO; |
| |
| dcmi->res = platform_get_resource(pdev, IORESOURCE_MEM, 0); |
| if (!dcmi->res) { |
| dev_err(&pdev->dev, "Could not get resource\n"); |
| return -ENODEV; |
| } |
| |
| dcmi->regs = devm_ioremap_resource(&pdev->dev, dcmi->res); |
| if (IS_ERR(dcmi->regs)) { |
| dev_err(&pdev->dev, "Could not map registers\n"); |
| return PTR_ERR(dcmi->regs); |
| } |
| |
| ret = devm_request_threaded_irq(&pdev->dev, irq, dcmi_irq_callback, |
| dcmi_irq_thread, IRQF_ONESHOT, |
| dev_name(&pdev->dev), dcmi); |
| if (ret) { |
| dev_err(&pdev->dev, "Unable to request irq %d\n", irq); |
| return ret; |
| } |
| |
| mclk = devm_clk_get(&pdev->dev, "mclk"); |
| if (IS_ERR(mclk)) { |
| if (PTR_ERR(mclk) != -EPROBE_DEFER) |
| dev_err(&pdev->dev, "Unable to get mclk\n"); |
| return PTR_ERR(mclk); |
| } |
| |
| chan = dma_request_chan(&pdev->dev, "tx"); |
| if (IS_ERR(chan)) { |
| ret = PTR_ERR(chan); |
| if (ret != -EPROBE_DEFER) |
| dev_err(&pdev->dev, |
| "Failed to request DMA channel: %d\n", ret); |
| return ret; |
| } |
| |
| spin_lock_init(&dcmi->irqlock); |
| mutex_init(&dcmi->lock); |
| mutex_init(&dcmi->dma_lock); |
| init_completion(&dcmi->complete); |
| INIT_LIST_HEAD(&dcmi->buffers); |
| |
| dcmi->dev = &pdev->dev; |
| dcmi->mclk = mclk; |
| dcmi->state = STOPPED; |
| dcmi->dma_chan = chan; |
| |
| q = &dcmi->queue; |
| |
| dcmi->v4l2_dev.mdev = &dcmi->mdev; |
| |
| /* Initialize media device */ |
| strscpy(dcmi->mdev.model, DRV_NAME, sizeof(dcmi->mdev.model)); |
| snprintf(dcmi->mdev.bus_info, sizeof(dcmi->mdev.bus_info), |
| "platform:%s", DRV_NAME); |
| dcmi->mdev.dev = &pdev->dev; |
| media_device_init(&dcmi->mdev); |
| |
| /* Initialize the top-level structure */ |
| ret = v4l2_device_register(&pdev->dev, &dcmi->v4l2_dev); |
| if (ret) |
| goto err_media_device_cleanup; |
| |
| dcmi->vdev = video_device_alloc(); |
| if (!dcmi->vdev) { |
| ret = -ENOMEM; |
| goto err_device_unregister; |
| } |
| |
| /* Video node */ |
| dcmi->vdev->fops = &dcmi_fops; |
| dcmi->vdev->v4l2_dev = &dcmi->v4l2_dev; |
| dcmi->vdev->queue = &dcmi->queue; |
| strscpy(dcmi->vdev->name, KBUILD_MODNAME, sizeof(dcmi->vdev->name)); |
| dcmi->vdev->release = video_device_release; |
| dcmi->vdev->ioctl_ops = &dcmi_ioctl_ops; |
| dcmi->vdev->lock = &dcmi->lock; |
| dcmi->vdev->device_caps = V4L2_CAP_VIDEO_CAPTURE | V4L2_CAP_STREAMING | |
| V4L2_CAP_READWRITE; |
| video_set_drvdata(dcmi->vdev, dcmi); |
| |
| /* Media entity pads */ |
| dcmi->vid_cap_pad.flags = MEDIA_PAD_FL_SINK; |
| ret = media_entity_pads_init(&dcmi->vdev->entity, |
| 1, &dcmi->vid_cap_pad); |
| if (ret) { |
| dev_err(dcmi->dev, "Failed to init media entity pad\n"); |
| goto err_device_release; |
| } |
| dcmi->vdev->entity.flags |= MEDIA_ENT_FL_DEFAULT; |
| |
| ret = video_register_device(dcmi->vdev, VFL_TYPE_VIDEO, -1); |
| if (ret) { |
| dev_err(dcmi->dev, "Failed to register video device\n"); |
| goto err_media_entity_cleanup; |
| } |
| |
| dev_dbg(dcmi->dev, "Device registered as %s\n", |
| video_device_node_name(dcmi->vdev)); |
| |
| /* Buffer queue */ |
| q->type = V4L2_BUF_TYPE_VIDEO_CAPTURE; |
| q->io_modes = VB2_MMAP | VB2_READ | VB2_DMABUF; |
| q->lock = &dcmi->lock; |
| q->drv_priv = dcmi; |
| q->buf_struct_size = sizeof(struct dcmi_buf); |
| q->ops = &dcmi_video_qops; |
| q->mem_ops = &vb2_dma_contig_memops; |
| q->timestamp_flags = V4L2_BUF_FLAG_TIMESTAMP_MONOTONIC; |
| q->min_buffers_needed = 2; |
| q->dev = &pdev->dev; |
| |
| ret = vb2_queue_init(q); |
| if (ret < 0) { |
| dev_err(&pdev->dev, "Failed to initialize vb2 queue\n"); |
| goto err_media_entity_cleanup; |
| } |
| |
| ret = dcmi_graph_init(dcmi); |
| if (ret < 0) |
| goto err_media_entity_cleanup; |
| |
| /* Reset device */ |
| ret = reset_control_assert(dcmi->rstc); |
| if (ret) { |
| dev_err(&pdev->dev, "Failed to assert the reset line\n"); |
| goto err_cleanup; |
| } |
| |
| usleep_range(3000, 5000); |
| |
| ret = reset_control_deassert(dcmi->rstc); |
| if (ret) { |
| dev_err(&pdev->dev, "Failed to deassert the reset line\n"); |
| goto err_cleanup; |
| } |
| |
| dev_info(&pdev->dev, "Probe done\n"); |
| |
| platform_set_drvdata(pdev, dcmi); |
| |
| pm_runtime_enable(&pdev->dev); |
| |
| return 0; |
| |
| err_cleanup: |
| v4l2_async_notifier_cleanup(&dcmi->notifier); |
| err_media_entity_cleanup: |
| media_entity_cleanup(&dcmi->vdev->entity); |
| err_device_release: |
| video_device_release(dcmi->vdev); |
| err_device_unregister: |
| v4l2_device_unregister(&dcmi->v4l2_dev); |
| err_media_device_cleanup: |
| media_device_cleanup(&dcmi->mdev); |
| dma_release_channel(dcmi->dma_chan); |
| |
| return ret; |
| } |
| |
| static int dcmi_remove(struct platform_device *pdev) |
| { |
| struct stm32_dcmi *dcmi = platform_get_drvdata(pdev); |
| |
| pm_runtime_disable(&pdev->dev); |
| |
| v4l2_async_notifier_unregister(&dcmi->notifier); |
| v4l2_async_notifier_cleanup(&dcmi->notifier); |
| media_entity_cleanup(&dcmi->vdev->entity); |
| v4l2_device_unregister(&dcmi->v4l2_dev); |
| media_device_cleanup(&dcmi->mdev); |
| |
| dma_release_channel(dcmi->dma_chan); |
| |
| return 0; |
| } |
| |
| static __maybe_unused int dcmi_runtime_suspend(struct device *dev) |
| { |
| struct stm32_dcmi *dcmi = dev_get_drvdata(dev); |
| |
| clk_disable_unprepare(dcmi->mclk); |
| |
| return 0; |
| } |
| |
| static __maybe_unused int dcmi_runtime_resume(struct device *dev) |
| { |
| struct stm32_dcmi *dcmi = dev_get_drvdata(dev); |
| int ret; |
| |
| ret = clk_prepare_enable(dcmi->mclk); |
| if (ret) |
| dev_err(dev, "%s: Failed to prepare_enable clock\n", __func__); |
| |
| return ret; |
| } |
| |
| static __maybe_unused int dcmi_suspend(struct device *dev) |
| { |
| /* disable clock */ |
| pm_runtime_force_suspend(dev); |
| |
| /* change pinctrl state */ |
| pinctrl_pm_select_sleep_state(dev); |
| |
| return 0; |
| } |
| |
| static __maybe_unused int dcmi_resume(struct device *dev) |
| { |
| /* restore pinctl default state */ |
| pinctrl_pm_select_default_state(dev); |
| |
| /* clock enable */ |
| pm_runtime_force_resume(dev); |
| |
| return 0; |
| } |
| |
| static const struct dev_pm_ops dcmi_pm_ops = { |
| SET_SYSTEM_SLEEP_PM_OPS(dcmi_suspend, dcmi_resume) |
| SET_RUNTIME_PM_OPS(dcmi_runtime_suspend, |
| dcmi_runtime_resume, NULL) |
| }; |
| |
| static struct platform_driver stm32_dcmi_driver = { |
| .probe = dcmi_probe, |
| .remove = dcmi_remove, |
| .driver = { |
| .name = DRV_NAME, |
| .of_match_table = of_match_ptr(stm32_dcmi_of_match), |
| .pm = &dcmi_pm_ops, |
| }, |
| }; |
| |
| module_platform_driver(stm32_dcmi_driver); |
| |
| MODULE_AUTHOR("Yannick Fertre <yannick.fertre@st.com>"); |
| MODULE_AUTHOR("Hugues Fruchet <hugues.fruchet@st.com>"); |
| MODULE_DESCRIPTION("STMicroelectronics STM32 Digital Camera Memory Interface driver"); |
| MODULE_LICENSE("GPL"); |