| // SPDX-License-Identifier: GPL-2.0 |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/leds/common.h> |
| #include <dt-bindings/pinctrl/qcom,pmic-gpio.h> |
| |
| #include "qcom-apq8064-v2.0.dtsi" |
| #include "pm8821.dtsi" |
| #include "pm8921.dtsi" |
| |
| / { |
| model = "Qualcomm APQ8064/IFC6410"; |
| compatible = "qcom,apq8064-ifc6410", "qcom,apq8064"; |
| |
| aliases { |
| serial0 = &gsbi7_serial; |
| serial1 = &gsbi6_serial; |
| i2c0 = &gsbi1_i2c; |
| i2c1 = &gsbi2_i2c; |
| i2c2 = &gsbi3_i2c; |
| i2c3 = &gsbi4_i2c; |
| spi0 = &gsbi5_spi; |
| }; |
| |
| chosen { |
| stdout-path = "serial0:115200n8"; |
| }; |
| |
| leds { |
| compatible = "gpio-leds"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <¬ify_led>; |
| |
| led-user1 { |
| label = "apq8064:green:user1"; |
| color = <LED_COLOR_ID_GREEN>; |
| gpios = <&pm8921_gpio 18 GPIO_ACTIVE_HIGH>; |
| default-state = "on"; |
| }; |
| }; |
| |
| hdmi-out { |
| compatible = "hdmi-connector"; |
| type = "d"; |
| |
| port { |
| hdmi_con: endpoint { |
| remote-endpoint = <&hdmi_out>; |
| }; |
| }; |
| }; |
| |
| sdcc4_pwrseq: pwrseq-sdcc4 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&wlan_default_gpios>; |
| compatible = "mmc-pwrseq-simple"; |
| reset-gpios = <&pm8921_gpio 43 GPIO_ACTIVE_LOW>; |
| }; |
| |
| ext_3p3v: regulator-ext-3p3v { |
| compatible = "regulator-fixed"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-name = "ext_3p3v"; |
| startup-delay-us = <0>; |
| gpio = <&tlmm_pinmux 77 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| regulator-boot-on; |
| }; |
| }; |
| |
| &gsbi1 { |
| qcom,mode = <GSBI_PROT_I2C>; |
| status = "okay"; |
| }; |
| |
| &gsbi1_i2c { |
| clock-frequency = <200000>; |
| status = "okay"; |
| |
| eeprom@52 { |
| compatible = "atmel,24c128"; |
| reg = <0x52>; |
| pagesize = <32>; |
| }; |
| }; |
| |
| &gsbi3 { |
| qcom,mode = <GSBI_PROT_I2C>; |
| status = "okay"; |
| }; |
| |
| &gsbi3_i2c { |
| status = "okay"; |
| }; |
| |
| &gsbi4 { |
| qcom,mode = <GSBI_PROT_I2C>; |
| status = "okay"; |
| }; |
| |
| /* CAM I2C MIPI-CSI connector */ |
| &gsbi4_i2c { |
| status = "okay"; |
| }; |
| |
| &gsbi5 { |
| qcom,mode = <GSBI_PROT_SPI>; |
| status = "okay"; |
| }; |
| |
| &gsbi5_spi { |
| num-cs = <1>; |
| cs-gpios = <&tlmm_pinmux 53 0>; |
| status = "okay"; |
| }; |
| |
| &gsbi6 { |
| qcom,mode = <GSBI_PROT_UART_W_FC>; |
| status = "okay"; |
| }; |
| |
| &gsbi6_serial { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&gsbi6_uart_4pins>; |
| status = "okay"; |
| }; |
| |
| &gsbi7 { |
| qcom,mode = <GSBI_PROT_I2C_UART>; |
| status = "okay"; |
| }; |
| |
| &gsbi7_serial { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&gsbi7_uart_2pins>; |
| status = "okay"; |
| }; |
| |
| &hdmi { |
| core-vdda-supply = <&pm8921_hdmi_switch>; |
| hpd-gpios = <&tlmm_pinmux 72 GPIO_ACTIVE_HIGH>; |
| status = "okay"; |
| }; |
| |
| &hdmi_in { |
| remote-endpoint = <&mdp_dtv_out>; |
| }; |
| |
| &hdmi_out { |
| remote-endpoint = <&hdmi_con>; |
| }; |
| |
| &hdmi_phy { |
| status = "okay"; |
| core-vdda-supply = <&pm8921_hdmi_switch>; |
| }; |
| |
| &mdp { |
| status = "okay"; |
| }; |
| |
| &mdp_dtv_out { |
| remote-endpoint = <&hdmi_in>; |
| }; |
| |
| &pcie { |
| status = "okay"; |
| vdda-supply = <&pm8921_s3>; |
| vdda_phy-supply = <&pm8921_lvs6>; |
| vdda_refclk-supply = <&ext_3p3v>; |
| pinctrl-0 = <&pcie_pins>; |
| pinctrl-names = "default"; |
| perst-gpios = <&tlmm_pinmux 27 GPIO_ACTIVE_LOW>; |
| }; |
| |
| &pm8821 { |
| interrupts-extended = <&tlmm_pinmux 76 IRQ_TYPE_LEVEL_LOW>; |
| }; |
| |
| &pm8921 { |
| interrupts-extended = <&tlmm_pinmux 74 IRQ_TYPE_LEVEL_LOW>; |
| }; |
| |
| &pm8921_gpio { |
| wlan_default_gpios: wlan-gpios-state { |
| pinconf { |
| pins = "gpio43"; |
| function = "normal"; |
| bias-disable; |
| power-source = <PM8921_GPIO_S4>; |
| }; |
| }; |
| |
| notify_led: nled-state { |
| pinconf { |
| pins = "gpio18"; |
| function = "normal"; |
| bias-disable; |
| power-source = <PM8921_GPIO_S4>; |
| }; |
| }; |
| }; |
| |
| &rpm { |
| regulators { |
| compatible = "qcom,rpm-pm8921-regulators"; |
| |
| vin_lvs1_3_6-supply = <&pm8921_s4>; |
| vin_lvs2-supply = <&pm8921_s1>; |
| vin_lvs4_5_7-supply = <&pm8921_s4>; |
| |
| vdd_l1_l2_l12_l18-supply = <&pm8921_s4>; |
| vdd_l24-supply = <&pm8921_s1>; |
| vdd_l25-supply = <&pm8921_s1>; |
| vdd_l26-supply = <&pm8921_s7>; |
| vdd_l27-supply = <&pm8921_s7>; |
| vdd_l28-supply = <&pm8921_s7>; |
| |
| /* Buck SMPS */ |
| pm8921_s1: s1 { |
| regulator-always-on; |
| regulator-min-microvolt = <1225000>; |
| regulator-max-microvolt = <1225000>; |
| qcom,switch-mode-frequency = <3200000>; |
| bias-pull-down; |
| }; |
| |
| pm8921_s3: s3 { |
| regulator-min-microvolt = <1000000>; |
| regulator-max-microvolt = <1400000>; |
| qcom,switch-mode-frequency = <4800000>; |
| }; |
| |
| pm8921_s4: s4 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| qcom,switch-mode-frequency = <3200000>; |
| }; |
| |
| pm8921_s7: s7 { |
| regulator-min-microvolt = <1300000>; |
| regulator-max-microvolt = <1300000>; |
| qcom,switch-mode-frequency = <3200000>; |
| }; |
| |
| pm8921_l3: l3 { |
| regulator-min-microvolt = <3050000>; |
| regulator-max-microvolt = <3300000>; |
| bias-pull-down; |
| }; |
| |
| pm8921_l4: l4 { |
| regulator-min-microvolt = <1000000>; |
| regulator-max-microvolt = <1800000>; |
| bias-pull-down; |
| }; |
| |
| pm8921_l5: l5 { |
| regulator-min-microvolt = <2750000>; |
| regulator-max-microvolt = <3000000>; |
| bias-pull-down; |
| }; |
| |
| pm8921_l6: l6 { |
| regulator-min-microvolt = <2950000>; |
| regulator-max-microvolt = <2950000>; |
| bias-pull-down; |
| }; |
| |
| pm8921_l23: l23 { |
| regulator-min-microvolt = <1700000>; |
| regulator-max-microvolt = <1900000>; |
| bias-pull-down; |
| }; |
| |
| pm8921_lvs1: lvs1 { |
| bias-pull-down; |
| }; |
| |
| pm8921_lvs6: lvs6 { |
| bias-pull-down; |
| }; |
| |
| pm8921_hdmi_switch: hdmi-switch { |
| bias-pull-down; |
| }; |
| }; |
| }; |
| |
| &sata_phy0 { |
| status = "okay"; |
| }; |
| |
| &sata0 { |
| target-supply = <&pm8921_s4>; |
| status = "okay"; |
| }; |
| |
| /* eMMC */ |
| &sdcc1 { |
| vmmc-supply = <&pm8921_l5>; |
| vqmmc-supply = <&pm8921_s4>; |
| status = "okay"; |
| }; |
| |
| /* External micro SD card */ |
| &sdcc3 { |
| vmmc-supply = <&pm8921_l6>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&card_detect>; |
| cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>; |
| status = "okay"; |
| }; |
| |
| /* WLAN */ |
| &sdcc4 { |
| vmmc-supply = <&ext_3p3v>; |
| vqmmc-supply = <&pm8921_lvs1>; |
| mmc-pwrseq = <&sdcc4_pwrseq>; |
| status = "okay"; |
| }; |
| |
| &tlmm_pinmux { |
| card_detect: card-detect-state { |
| pins = "gpio26"; |
| function = "gpio"; |
| bias-disable; |
| }; |
| |
| pcie_pins: pcie-state { |
| pins = "gpio27"; |
| function = "gpio"; |
| drive-strength = <12>; |
| bias-disable; |
| }; |
| }; |
| |
| &usb_hs1_phy { |
| v3p3-supply = <&pm8921_l3>; |
| v1p8-supply = <&pm8921_l4>; |
| }; |
| |
| &usb_hs3_phy { |
| v3p3-supply = <&pm8921_l3>; |
| v1p8-supply = <&pm8921_l23>; |
| }; |
| |
| &usb_hs4_phy { |
| v3p3-supply = <&pm8921_l3>; |
| v1p8-supply = <&pm8921_l23>; |
| }; |
| |
| /* OTG */ |
| &usb1 { |
| dr_mode = "otg"; |
| status = "okay"; |
| }; |
| |
| &usb3 { |
| dr_mode = "host"; |
| status = "okay"; |
| }; |
| |
| &usb4 { |
| dr_mode = "host"; |
| status = "okay"; |
| }; |
