| // SPDX-License-Identifier: GPL-2.0 |
| #include "qcom-msm8974.dtsi" |
| #include "pm8841.dtsi" |
| #include "pm8941.dtsi" |
| #include <dt-bindings/input/input.h> |
| #include <dt-bindings/leds/common.h> |
| #include <dt-bindings/pinctrl/qcom,pmic-gpio.h> |
| |
| / { |
| model = "Samsung Galaxy Note 3"; |
| compatible = "samsung,hlte", "qcom,msm8974"; |
| chassis-type = "handset"; |
| |
| aliases { |
| mmc0 = &sdhc_1; /* SDC1 eMMC slot */ |
| mmc1 = &sdhc_3; /* SDC3 SD card slot */ |
| serial0 = &blsp1_uart1; |
| }; |
| |
| chosen { |
| stdout-path = "serial0:115200n8"; |
| }; |
| |
| gpio-keys { |
| compatible = "gpio-keys"; |
| |
| pinctrl-0 = <&gpio_keys_pin_a>; |
| pinctrl-names = "default"; |
| |
| key-home { |
| label = "Home Key"; |
| gpios = <&pm8941_gpios 3 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_HOMEPAGE>; |
| wakeup-source; |
| debounce-interval = <15>; |
| }; |
| |
| key-volume-down { |
| label = "Volume Down"; |
| gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_VOLUMEDOWN>; |
| debounce-interval = <15>; |
| }; |
| |
| key-volume-up { |
| label = "Volume Up"; |
| gpios = <&pm8941_gpios 5 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_VOLUMEUP>; |
| debounce-interval = <15>; |
| }; |
| }; |
| |
| touch_ldo: regulator-touch { |
| compatible = "regulator-fixed"; |
| regulator-name = "touch-ldo"; |
| |
| gpio = <&pm8941_gpios 9 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| regulator-boot-on; |
| |
| pinctrl-0 = <&touch_ldo_pin>; |
| pinctrl-names = "default"; |
| }; |
| }; |
| |
| &blsp1_i2c2 { |
| status = "okay"; |
| |
| touchscreen@20 { |
| compatible = "syna,rmi4-i2c"; |
| reg = <0x20>; |
| |
| interrupt-parent = <&pm8941_gpios>; |
| interrupts = <30 IRQ_TYPE_EDGE_FALLING>; |
| |
| vdd-supply = <&pm8941_l10>; |
| vio-supply = <&touch_ldo>; |
| |
| pinctrl-0 = <&touch_pin>; |
| pinctrl-names = "default"; |
| |
| syna,startup-delay-ms = <100>; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| rmi4-f01@1 { |
| reg = <0x1>; |
| syna,nosleep-mode = <1>; |
| }; |
| |
| rmi4-f12@12 { |
| reg = <0x12>; |
| syna,sensor-type = <1>; |
| }; |
| }; |
| }; |
| |
| &blsp2_i2c6 { |
| status = "okay"; |
| |
| fuelgauge@36 { |
| compatible = "maxim,max17048"; |
| reg = <0x36>; |
| |
| maxim,double-soc; |
| maxim,rcomp = /bits/ 8 <0x56>; |
| |
| interrupt-parent = <&pm8941_gpios>; |
| interrupts = <26 IRQ_TYPE_EDGE_FALLING>; |
| |
| pinctrl-0 = <&fuelgauge_pin>; |
| pinctrl-names = "default"; |
| }; |
| }; |
| |
| &blsp1_uart2 { |
| status = "okay"; |
| }; |
| |
| &pm8941_gpios { |
| gpio_keys_pin_a: gpio-keys-active-state { |
| pins = "gpio2", "gpio3", "gpio5"; |
| function = "normal"; |
| bias-pull-up; |
| power-source = <PM8941_GPIO_S3>; |
| }; |
| |
| fuelgauge_pin: fuelgauge-int-state { |
| pins = "gpio26"; |
| function = "normal"; |
| bias-disable; |
| input-enable; |
| power-source = <PM8941_GPIO_S3>; |
| }; |
| |
| touch_pin: touchscreen-int-state { |
| pins = "gpio30"; |
| function = "normal"; |
| bias-disable; |
| input-enable; |
| power-source = <PM8941_GPIO_S3>; |
| }; |
| |
| touch_ldo_pin: touchscreen-ldo-state { |
| pins = "gpio9"; |
| function = "normal"; |
| output-high; |
| power-source = <PM8941_GPIO_S3>; |
| qcom,drive-strength = <PMIC_GPIO_STRENGTH_HIGH>; |
| }; |
| }; |
| |
| &remoteproc_adsp { |
| cx-supply = <&pm8841_s2>; |
| status = "okay"; |
| }; |
| |
| &remoteproc_mss { |
| cx-supply = <&pm8841_s2>; |
| mss-supply = <&pm8841_s3>; |
| mx-supply = <&pm8841_s1>; |
| pll-supply = <&pm8941_l12>; |
| status = "okay"; |
| }; |
| |
| &rpm_requests { |
| regulators-0 { |
| compatible = "qcom,rpm-pm8841-regulators"; |
| |
| pm8841_s1: s1 { |
| regulator-min-microvolt = <675000>; |
| regulator-max-microvolt = <1050000>; |
| }; |
| |
| pm8841_s2: s2 { |
| regulator-min-microvolt = <500000>; |
| regulator-max-microvolt = <1050000>; |
| }; |
| |
| pm8841_s3: s3 { |
| regulator-min-microvolt = <1050000>; |
| regulator-max-microvolt = <1050000>; |
| }; |
| |
| pm8841_s4: s4 { |
| regulator-min-microvolt = <815000>; |
| regulator-max-microvolt = <900000>; |
| }; |
| }; |
| |
| regulators-1 { |
| compatible = "qcom,rpm-pm8941-regulators"; |
| |
| pm8941_s1: s1 { |
| regulator-min-microvolt = <1300000>; |
| regulator-max-microvolt = <1300000>; |
| regulator-always-on; |
| }; |
| |
| pm8941_s2: s2 { |
| regulator-min-microvolt = <2150000>; |
| regulator-max-microvolt = <2150000>; |
| }; |
| |
| pm8941_s3: s3 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| pm8941_l1: l1 { |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| }; |
| |
| pm8941_l2: l2 { |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| }; |
| |
| pm8941_l3: l3 { |
| regulator-min-microvolt = <1050000>; |
| regulator-max-microvolt = <1225000>; |
| }; |
| |
| pm8941_l4: l4 { |
| regulator-min-microvolt = <1225000>; |
| regulator-max-microvolt = <1225000>; |
| }; |
| |
| pm8941_l5: l5 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| pm8941_l6: l6 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| pm8941_l7: l7 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| pm8941_l8: l8 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| pm8941_l9: l9 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <2950000>; |
| }; |
| |
| pm8941_l10: l10 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| pm8941_l11: l11 { |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1350000>; |
| }; |
| |
| pm8941_l12: l12 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-always-on; |
| }; |
| |
| pm8941_l13: l13 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| |
| pm8941_l14: l14 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| pm8941_l15: l15 { |
| regulator-min-microvolt = <2050000>; |
| regulator-max-microvolt = <2050000>; |
| }; |
| |
| pm8941_l16: l16 { |
| regulator-min-microvolt = <2700000>; |
| regulator-max-microvolt = <2700000>; |
| }; |
| |
| pm8941_l17: l17 { |
| regulator-min-microvolt = <2850000>; |
| regulator-max-microvolt = <3000000>; |
| }; |
| |
| pm8941_l18: l18 { |
| regulator-min-microvolt = <2850000>; |
| regulator-max-microvolt = <2850000>; |
| }; |
| |
| pm8941_l19: l19 { |
| regulator-min-microvolt = <2900000>; |
| regulator-max-microvolt = <3350000>; |
| }; |
| |
| pm8941_l20: l20 { |
| regulator-min-microvolt = <2950000>; |
| regulator-max-microvolt = <2950000>; |
| regulator-system-load = <200000>; |
| regulator-allow-set-load; |
| }; |
| |
| pm8941_l21: l21 { |
| regulator-min-microvolt = <2950000>; |
| regulator-max-microvolt = <2950000>; |
| regulator-system-load = <200000>; |
| regulator-allow-set-load; |
| }; |
| |
| pm8941_l22: l22 { |
| regulator-min-microvolt = <2500000>; |
| regulator-max-microvolt = <3000000>; |
| }; |
| |
| pm8941_l23: l23 { |
| regulator-min-microvolt = <2400000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| |
| pm8941_l24: l24 { |
| regulator-min-microvolt = <3075000>; |
| regulator-max-microvolt = <3075000>; |
| }; |
| }; |
| }; |
| |
| &sdhc_1 { |
| vmmc-supply = <&pm8941_l20>; |
| vqmmc-supply = <&pm8941_s3>; |
| |
| pinctrl-0 = <&sdhc1_pin_a>; |
| pinctrl-names = "default"; |
| |
| status = "okay"; |
| }; |
| |
| &sdhc_3 { |
| max-frequency = <100000000>; |
| |
| vmmc-supply = <&pm8941_l21>; |
| vqmmc-supply = <&pm8941_l21>; |
| |
| pinctrl-0 = <&sdhc3_pin_a>; |
| pinctrl-names = "default"; |
| |
| status = "okay"; |
| }; |
| |
| &tlmm { |
| sdhc1_pin_a: sdhc1-pin-active-state { |
| clk-pins { |
| pins = "sdc1_clk"; |
| drive-strength = <4>; |
| bias-disable; |
| }; |
| |
| cmd-data-pins { |
| pins = "sdc1_cmd", "sdc1_data"; |
| drive-strength = <4>; |
| bias-pull-up; |
| }; |
| }; |
| |
| sdhc3_pin_a: sdhc3-pin-active-state { |
| pins = "gpio35", "gpio36", "gpio37", "gpio38", "gpio39", "gpio40"; |
| function = "sdc3"; |
| drive-strength = <8>; |
| bias-disable; |
| }; |
| }; |
| |
| &usb { |
| phys = <&usb_hs1_phy>; |
| phy-select = <&tcsr 0xb000 0>; |
| |
| hnp-disable; |
| srp-disable; |
| adp-disable; |
| |
| status = "okay"; |
| }; |
| |
| &usb_hs1_phy { |
| v1p8-supply = <&pm8941_l6>; |
| v3p3-supply = <&pm8941_l24>; |
| |
| qcom,init-seq = /bits/ 8 <0x1 0x64>; |
| |
| status = "okay"; |
| }; |