drivers/scsi/scsi_scan.c

// SPDX-License-Identifier: GPL-2.0
/*
 * scsi_scan.c
 *
 * Copyright (C) 2000 Eric Youngdale,
 * Copyright (C) 2002 Patrick Mansfield
 *
 * The general scanning/probing algorithm is as follows, exceptions are
 * made to it depending on device specific flags, compilation options, and
 * global variable (boot or module load time) settings.
 *
 * A specific LUN is scanned via an INQUIRY command; if the LUN has a
 * device attached, a scsi_device is allocated and setup for it.
 *
 * For every id of every channel on the given host:
 *
 * 	Scan LUN 0; if the target responds to LUN 0 (even if there is no
 * 	device or storage attached to LUN 0):
 *
 * 		If LUN 0 has a device attached, allocate and setup a
 * 		scsi_device for it.
 *
 * 		If target is SCSI-3 or up, issue a REPORT LUN, and scan
 * 		all of the LUNs returned by the REPORT LUN; else,
 * 		sequentially scan LUNs up until some maximum is reached,
 * 		or a LUN is seen that cannot have a device attached to it.
 */

#include <linux/module.h>
#include <linux/moduleparam.h>
#include <linux/init.h>
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <linux/kthread.h>
#include <linux/spinlock.h>
#include <linux/async.h>
#include <linux/slab.h>
#include <asm/unaligned.h>

#include <scsi/scsi.h>
#include <scsi/scsi_cmnd.h>
#include <scsi/scsi_device.h>
#include <scsi/scsi_driver.h>
#include <scsi/scsi_devinfo.h>
#include <scsi/scsi_host.h>
#include <scsi/scsi_transport.h>
#include <scsi/scsi_dh.h>
#include <scsi/scsi_eh.h>

#include "scsi_priv.h"
#include "scsi_logging.h"

#define ALLOC_FAILURE_MSG	KERN_ERR "%s: Allocation failure during" \
	" SCSI scanning, some SCSI devices might not be configured\n"

/*
 * Default timeout
 */
#define SCSI_TIMEOUT (2*HZ)
#define SCSI_REPORT_LUNS_TIMEOUT (30*HZ)

/*
 * Prefix values for the SCSI id's (stored in sysfs name field)
 */
#define SCSI_UID_SER_NUM 'S'
#define SCSI_UID_UNKNOWN 'Z'

/*
 * Return values of some of the scanning functions.
 *
 * SCSI_SCAN_NO_RESPONSE: no valid response received from the target, this
 * includes allocation or general failures preventing IO from being sent.
 *
 * SCSI_SCAN_TARGET_PRESENT: target responded, but no device is available
 * on the given LUN.
 *
 * SCSI_SCAN_LUN_PRESENT: target responded, and a device is available on a
 * given LUN.
 */
#define SCSI_SCAN_NO_RESPONSE		0
#define SCSI_SCAN_TARGET_PRESENT	1
#define SCSI_SCAN_LUN_PRESENT		2

static const char *scsi_null_device_strs = "nullnullnullnull";

#define MAX_SCSI_LUNS	512

static u64 max_scsi_luns = MAX_SCSI_LUNS;

module_param_named(max_luns, max_scsi_luns, ullong, S_IRUGO|S_IWUSR);
MODULE_PARM_DESC(max_luns,
		 "last scsi LUN (should be between 1 and 2^64-1)");

#ifdef CONFIG_SCSI_SCAN_ASYNC
#define SCSI_SCAN_TYPE_DEFAULT "async"
#else
#define SCSI_SCAN_TYPE_DEFAULT "sync"
#endif

static char scsi_scan_type[7] = SCSI_SCAN_TYPE_DEFAULT;

module_param_string(scan, scsi_scan_type, sizeof(scsi_scan_type),
		    S_IRUGO|S_IWUSR);
MODULE_PARM_DESC(scan, "sync, async, manual, or none. "
		 "Setting to 'manual' disables automatic scanning, but allows "
		 "for manual device scan via the 'scan' sysfs attribute.");

static unsigned int scsi_inq_timeout = SCSI_TIMEOUT/HZ + 18;

module_param_named(inq_timeout, scsi_inq_timeout, uint, S_IRUGO|S_IWUSR);
MODULE_PARM_DESC(inq_timeout, 
		 "Timeout (in seconds) waiting for devices to answer INQUIRY."
		 " Default is 20. Some devices may need more; most need less.");

/* This lock protects only this list */
static DEFINE_SPINLOCK(async_scan_lock);
static LIST_HEAD(scanning_hosts);

struct async_scan_data {
	struct list_head list;
	struct Scsi_Host *shost;
	struct completion prev_finished;
};

/*
 * scsi_enable_async_suspend - Enable async suspend and resume
 */
void scsi_enable_async_suspend(struct device *dev)
{
	/*
	 * If a user has disabled async probing a likely reason is due to a
	 * storage enclosure that does not inject staggered spin-ups. For
	 * safety, make resume synchronous as well in that case.
	 */
	if (strncmp(scsi_scan_type, "async", 5) != 0)
		return;
	/* Enable asynchronous suspend and resume. */
	device_enable_async_suspend(dev);
}

/**
 * scsi_complete_async_scans - Wait for asynchronous scans to complete
 *
 * When this function returns, any host which started scanning before
 * this function was called will have finished its scan.  Hosts which
 * started scanning after this function was called may or may not have
 * finished.
 */
int scsi_complete_async_scans(void)
{
	struct async_scan_data *data;

	do {
		if (list_empty(&scanning_hosts))
			return 0;
		/* If we can't get memory immediately, that's OK.  Just
		 * sleep a little.  Even if we never get memory, the async
		 * scans will finish eventually.
		 */
		data = kmalloc(sizeof(*data), GFP_KERNEL);
		if (!data)
			msleep(1);
	} while (!data);

	data->shost = NULL;
	init_completion(&data->prev_finished);

	spin_lock(&async_scan_lock);
	/* Check that there's still somebody else on the list */
	if (list_empty(&scanning_hosts))
		goto done;
	list_add_tail(&data->list, &scanning_hosts);
	spin_unlock(&async_scan_lock);

	printk(KERN_INFO "scsi: waiting for bus probes to complete ...\n");
	wait_for_completion(&data->prev_finished);

	spin_lock(&async_scan_lock);
	list_del(&data->list);
	if (!list_empty(&scanning_hosts)) {
		struct async_scan_data *next = list_entry(scanning_hosts.next,
				struct async_scan_data, list);
		complete(&next->prev_finished);
	}
 done:
	spin_unlock(&async_scan_lock);

	kfree(data);
	return 0;
}

/**
 * scsi_unlock_floptical - unlock device via a special MODE SENSE command
 * @sdev:	scsi device to send command to
 * @result:	area to store the result of the MODE SENSE
 *
 * Description:
 *     Send a vendor specific MODE SENSE (not a MODE SELECT) command.
 *     Called for BLIST_KEY devices.
 **/
static void scsi_unlock_floptical(struct scsi_device *sdev,
				  unsigned char *result)
{
	unsigned char scsi_cmd[MAX_COMMAND_SIZE];

	sdev_printk(KERN_NOTICE, sdev, "unlocking floptical drive\n");
	scsi_cmd[0] = MODE_SENSE;
	scsi_cmd[1] = 0;
	scsi_cmd[2] = 0x2e;
	scsi_cmd[3] = 0;
	scsi_cmd[4] = 0x2a;     /* size */
	scsi_cmd[5] = 0;
	scsi_execute_cmd(sdev, scsi_cmd, REQ_OP_DRV_IN, result, 0x2a,
			 SCSI_TIMEOUT, 3, NULL);
}

static int scsi_realloc_sdev_budget_map(struct scsi_device *sdev,
					unsigned int depth)
{
	int new_shift = sbitmap_calculate_shift(depth);
	bool need_alloc = !sdev->budget_map.map;
	bool need_free = false;
	int ret;
	struct sbitmap sb_backup;

	depth = min_t(unsigned int, depth, scsi_device_max_queue_depth(sdev));

	/*
	 * realloc if new shift is calculated, which is caused by setting
	 * up one new default queue depth after calling ->device_configure
	 */
	if (!need_alloc && new_shift != sdev->budget_map.shift)
		need_alloc = need_free = true;

	if (!need_alloc)
		return 0;

	/*
	 * Request queue has to be frozen for reallocating budget map,
	 * and here disk isn't added yet, so freezing is pretty fast
	 */
	if (need_free) {
		blk_mq_freeze_queue(sdev->request_queue);
		sb_backup = sdev->budget_map;
	}
	ret = sbitmap_init_node(&sdev->budget_map,
				scsi_device_max_queue_depth(sdev),
				new_shift, GFP_KERNEL,
				sdev->request_queue->node, false, true);
	if (!ret)
		sbitmap_resize(&sdev->budget_map, depth);

	if (need_free) {
		if (ret)
			sdev->budget_map = sb_backup;
		else
			sbitmap_free(&sb_backup);
		ret = 0;
		blk_mq_unfreeze_queue(sdev->request_queue);
	}
	return ret;
}

/**
 * scsi_alloc_sdev - allocate and setup a scsi_Device
 * @starget: which target to allocate a &scsi_device for
 * @lun: which lun
 * @hostdata: usually NULL and set by ->slave_alloc instead
 *
 * Description:
 *     Allocate, initialize for io, and return a pointer to a scsi_Device.
 *     Stores the @shost, @channel, @id, and @lun in the scsi_Device, and
 *     adds scsi_Device to the appropriate list.
 *
 * Return value:
 *     scsi_Device pointer, or NULL on failure.
 **/
static struct scsi_device *scsi_alloc_sdev(struct scsi_target *starget,
					   u64 lun, void *hostdata)
{
	unsigned int depth;
	struct scsi_device *sdev;
	struct request_queue *q;
	int display_failure_msg = 1, ret;
	struct Scsi_Host *shost = dev_to_shost(starget->dev.parent);
	struct queue_limits lim;

	sdev = kzalloc(sizeof(*sdev) + shost->transportt->device_size,
		       GFP_KERNEL);
	if (!sdev)
		goto out;

	sdev->vendor = scsi_null_device_strs;
	sdev->model = scsi_null_device_strs;
	sdev->rev = scsi_null_device_strs;
	sdev->host = shost;
	sdev->queue_ramp_up_period = SCSI_DEFAULT_RAMP_UP_PERIOD;
	sdev->id = starget->id;
	sdev->lun = lun;
	sdev->channel = starget->channel;
	mutex_init(&sdev->state_mutex);
	sdev->sdev_state = SDEV_CREATED;
	INIT_LIST_HEAD(&sdev->siblings);
	INIT_LIST_HEAD(&sdev->same_target_siblings);
	INIT_LIST_HEAD(&sdev->starved_entry);
	INIT_LIST_HEAD(&sdev->event_list);
	spin_lock_init(&sdev->list_lock);
	mutex_init(&sdev->inquiry_mutex);
	INIT_WORK(&sdev->event_work, scsi_evt_thread);
	INIT_WORK(&sdev->requeue_work, scsi_requeue_run_queue);

	sdev->sdev_gendev.parent = get_device(&starget->dev);
	sdev->sdev_target = starget;

	/* usually NULL and set by ->slave_alloc instead */
	sdev->hostdata = hostdata;

	/* if the device needs this changing, it may do so in the
	 * slave_configure function */
	sdev->max_device_blocked = SCSI_DEFAULT_DEVICE_BLOCKED;

	/*
	 * Some low level driver could use device->type
	 */
	sdev->type = -1;

	/*
	 * Assume that the device will have handshaking problems,
	 * and then fix this field later if it turns out it
	 * doesn't
	 */
	sdev->borken = 1;

	sdev->sg_reserved_size = INT_MAX;

	scsi_init_limits(shost, &lim);
	q = blk_mq_alloc_queue(&sdev->host->tag_set, &lim, NULL);
	if (IS_ERR(q)) {
		/* release fn is set up in scsi_sysfs_device_initialise, so
		 * have to free and put manually here */
		put_device(&starget->dev);
		kfree(sdev);
		goto out;
	}
	kref_get(&sdev->host->tagset_refcnt);
	sdev->request_queue = q;
	q->queuedata = sdev;

	depth = sdev->host->cmd_per_lun ?: 1;

	/*
	 * Use .can_queue as budget map's depth because we have to
	 * support adjusting queue depth from sysfs. Meantime use
	 * default device queue depth to figure out sbitmap shift
	 * since we use this queue depth most of times.
	 */
	if (scsi_realloc_sdev_budget_map(sdev, depth)) {
		put_device(&starget->dev);
		kfree(sdev);
		goto out;
	}

	scsi_change_queue_depth(sdev, depth);

	scsi_sysfs_device_initialize(sdev);

	if (shost->hostt->slave_alloc) {
		ret = shost->hostt->slave_alloc(sdev);
		if (ret) {
			/*
			 * if LLDD reports slave not present, don't clutter
			 * console with alloc failure messages
			 */
			if (ret == -ENXIO)
				display_failure_msg = 0;
			goto out_device_destroy;
		}
	}

	return sdev;

out_device_destroy:
	__scsi_remove_device(sdev);
out:
	if (display_failure_msg)
		printk(ALLOC_FAILURE_MSG, __func__);
	return NULL;
}

static void scsi_target_destroy(struct scsi_target *starget)
{
	struct device *dev = &starget->dev;
	struct Scsi_Host *shost = dev_to_shost(dev->parent);
	unsigned long flags;

	BUG_ON(starget->state == STARGET_DEL);
	starget->state = STARGET_DEL;
	transport_destroy_device(dev);
	spin_lock_irqsave(shost->host_lock, flags);
	if (shost->hostt->target_destroy)
		shost->hostt->target_destroy(starget);
	list_del_init(&starget->siblings);
	spin_unlock_irqrestore(shost->host_lock, flags);
	put_device(dev);
}

static void scsi_target_dev_release(struct device *dev)
{
	struct device *parent = dev->parent;
	struct scsi_target *starget = to_scsi_target(dev);

	kfree(starget);
	put_device(parent);
}

static const struct device_type scsi_target_type = {
	.name =		"scsi_target",
	.release =	scsi_target_dev_release,
};

int scsi_is_target_device(const struct device *dev)
{
	return dev->type == &scsi_target_type;
}
EXPORT_SYMBOL(scsi_is_target_device);

static struct scsi_target *__scsi_find_target(struct device *parent,
					      int channel, uint id)
{
	struct scsi_target *starget, *found_starget = NULL;
	struct Scsi_Host *shost = dev_to_shost(parent);
	/*
	 * Search for an existing target for this sdev.
	 */
	list_for_each_entry(starget, &shost->__targets, siblings) {
		if (starget->id == id &&
		    starget->channel == channel) {
			found_starget = starget;
			break;
		}
	}
	if (found_starget)
		get_device(&found_starget->dev);

	return found_starget;
}

/**
 * scsi_target_reap_ref_release - remove target from visibility
 * @kref: the reap_ref in the target being released
 *
 * Called on last put of reap_ref, which is the indication that no device
 * under this target is visible anymore, so render the target invisible in
 * sysfs.  Note: we have to be in user context here because the target reaps
 * should be done in places where the scsi device visibility is being removed.
 */
static void scsi_target_reap_ref_release(struct kref *kref)
{
	struct scsi_target *starget
		= container_of(kref, struct scsi_target, reap_ref);

	/*
	 * if we get here and the target is still in a CREATED state that
	 * means it was allocated but never made visible (because a scan
	 * turned up no LUNs), so don't call device_del() on it.
	 */
	if ((starget->state != STARGET_CREATED) &&
	    (starget->state != STARGET_CREATED_REMOVE)) {
		transport_remove_device(&starget->dev);
		device_del(&starget->dev);
	}
	scsi_target_destroy(starget);
}

static void scsi_target_reap_ref_put(struct scsi_target *starget)
{
	kref_put(&starget->reap_ref, scsi_target_reap_ref_release);
}

/**
 * scsi_alloc_target - allocate a new or find an existing target
 * @parent:	parent of the target (need not be a scsi host)
 * @channel:	target channel number (zero if no channels)
 * @id:		target id number
 *
 * Return an existing target if one exists, provided it hasn't already
 * gone into STARGET_DEL state, otherwise allocate a new target.
 *
 * The target is returned with an incremented reference, so the caller
 * is responsible for both reaping and doing a last put
 */
static struct scsi_target *scsi_alloc_target(struct device *parent,
					     int channel, uint id)
{
	struct Scsi_Host *shost = dev_to_shost(parent);
	struct device *dev = NULL;
	unsigned long flags;
	const int size = sizeof(struct scsi_target)
		+ shost->transportt->target_size;
	struct scsi_target *starget;
	struct scsi_target *found_target;
	int error, ref_got;

	starget = kzalloc(size, GFP_KERNEL);
	if (!starget) {
		printk(KERN_ERR "%s: allocation failure\n", __func__);
		return NULL;
	}
	dev = &starget->dev;
	device_initialize(dev);
	kref_init(&starget->reap_ref);
	dev->parent = get_device(parent);
	dev_set_name(dev, "target%d:%d:%d", shost->host_no, channel, id);
	dev->bus = &scsi_bus_type;
	dev->type = &scsi_target_type;
	scsi_enable_async_suspend(dev);
	starget->id = id;
	starget->channel = channel;
	starget->can_queue = 0;
	INIT_LIST_HEAD(&starget->siblings);
	INIT_LIST_HEAD(&starget->devices);
	starget->state = STARGET_CREATED;
	starget->scsi_level = SCSI_2;
	starget->max_target_blocked = SCSI_DEFAULT_TARGET_BLOCKED;
 retry:
	spin_lock_irqsave(shost->host_lock, flags);

	found_target = __scsi_find_target(parent, channel, id);
	if (found_target)
		goto found;

	list_add_tail(&starget->siblings, &shost->__targets);
	spin_unlock_irqrestore(shost->host_lock, flags);
	/* allocate and add */
	transport_setup_device(dev);
	if (shost->hostt->target_alloc) {
		error = shost->hostt->target_alloc(starget);

		if(error) {
			if (error != -ENXIO)
				dev_err(dev, "target allocation failed, error %d\n", error);
			/* don't want scsi_target_reap to do the final
			 * put because it will be under the host lock */
			scsi_target_destroy(starget);
			return NULL;
		}
	}
	get_device(dev);

	return starget;

 found:
	/*
	 * release routine already fired if kref is zero, so if we can still
	 * take the reference, the target must be alive.  If we can't, it must
	 * be dying and we need to wait for a new target
	 */
	ref_got = kref_get_unless_zero(&found_target->reap_ref);

	spin_unlock_irqrestore(shost->host_lock, flags);
	if (ref_got) {
		put_device(dev);
		return found_target;
	}
	/*
	 * Unfortunately, we found a dying target; need to wait until it's
	 * dead before we can get a new one.  There is an anomaly here.  We
	 * *should* call scsi_target_reap() to balance the kref_get() of the
	 * reap_ref above.  However, since the target being released, it's
	 * already invisible and the reap_ref is irrelevant.  If we call
	 * scsi_target_reap() we might spuriously do another device_del() on
	 * an already invisible target.
	 */
	put_device(&found_target->dev);
	/*
	 * length of time is irrelevant here, we just want to yield the CPU
	 * for a tick to avoid busy waiting for the target to die.
	 */
	msleep(1);
	goto retry;
}

/**
 * scsi_target_reap - check to see if target is in use and destroy if not
 * @starget: target to be checked
 *
 * This is used after removing a LUN or doing a last put of the target
 * it checks atomically that nothing is using the target and removes
 * it if so.
 */
void scsi_target_reap(struct scsi_target *starget)
{
	/*
	 * serious problem if this triggers: STARGET_DEL is only set in the if
	 * the reap_ref drops to zero, so we're trying to do another final put
	 * on an already released kref
	 */
	BUG_ON(starget->state == STARGET_DEL);
	scsi_target_reap_ref_put(starget);
}

/**
 * scsi_sanitize_inquiry_string - remove non-graphical chars from an
 *                                INQUIRY result string
 * @s: INQUIRY result string to sanitize
 * @len: length of the string
 *
 * Description:
 *	The SCSI spec says that INQUIRY vendor, product, and revision
 *	strings must consist entirely of graphic ASCII characters,
 *	padded on the right with spaces.  Since not all devices obey
 *	this rule, we will replace non-graphic or non-ASCII characters
 *	with spaces.  Exception: a NUL character is interpreted as a
 *	string terminator, so all the following characters are set to
 *	spaces.
 **/
void scsi_sanitize_inquiry_string(unsigned char *s, int len)
{
	int terminated = 0;

	for (; len > 0; (--len, ++s)) {
		if (*s == 0)
			terminated = 1;
		if (terminated || *s < 0x20 || *s > 0x7e)
			*s = ' ';
	}
}
EXPORT_SYMBOL(scsi_sanitize_inquiry_string);


/**
 * scsi_probe_lun - probe a single LUN using a SCSI INQUIRY
 * @sdev:	scsi_device to probe
 * @inq_result:	area to store the INQUIRY result
 * @result_len: len of inq_result
 * @bflags:	store any bflags found here
 *
 * Description:
 *     Probe the lun associated with @req using a standard SCSI INQUIRY;
 *
 *     If the INQUIRY is successful, zero is returned and the
 *     INQUIRY data is in @inq_result; the scsi_level and INQUIRY length
 *     are copied to the scsi_device any flags value is stored in *@bflags.
 **/
static int scsi_probe_lun(struct scsi_device *sdev, unsigned char *inq_result,
			  int result_len, blist_flags_t *bflags)
{
	unsigned char scsi_cmd[MAX_COMMAND_SIZE];
	int first_inquiry_len, try_inquiry_len, next_inquiry_len;
	int response_len = 0;
	int pass, count, result, resid;
	struct scsi_failure failure_defs[] = {
		/*
		 * not-ready to ready transition [asc/ascq=0x28/0x0] or
		 * power-on, reset [asc/ascq=0x29/0x0], continue. INQUIRY
		 * should not yield UNIT_ATTENTION but many buggy devices do
		 * so anyway.
		 */
		{
			.sense = UNIT_ATTENTION,
			.asc = 0x28,
			.result = SAM_STAT_CHECK_CONDITION,
		},
		{
			.sense = UNIT_ATTENTION,
			.asc = 0x29,
			.result = SAM_STAT_CHECK_CONDITION,
		},
		{
			.allowed = 1,
			.result = DID_TIME_OUT << 16,
		},
		{}
	};
	struct scsi_failures failures = {
		.total_allowed = 3,
		.failure_definitions = failure_defs,
	};
	const struct scsi_exec_args exec_args = {
		.resid = &resid,
		.failures = &failures,
	};

	*bflags = 0;

	/* Perform up to 3 passes.  The first pass uses a conservative
	 * transfer length of 36 unless sdev->inquiry_len specifies a
	 * different value. */
	first_inquiry_len = sdev->inquiry_len ? sdev->inquiry_len : 36;
	try_inquiry_len = first_inquiry_len;
	pass = 1;

 next_pass:
	SCSI_LOG_SCAN_BUS(3, sdev_printk(KERN_INFO, sdev,
				"scsi scan: INQUIRY pass %d length %d\n",
				pass, try_inquiry_len));

	/* Each pass gets up to three chances to ignore Unit Attention */
	scsi_failures_reset_retries(&failures);

	for (count = 0; count < 3; ++count) {
		memset(scsi_cmd, 0, 6);
		scsi_cmd[0] = INQUIRY;
		scsi_cmd[4] = (unsigned char) try_inquiry_len;

		memset(inq_result, 0, try_inquiry_len);

		result = scsi_execute_cmd(sdev,  scsi_cmd, REQ_OP_DRV_IN,
					  inq_result, try_inquiry_len,
					  HZ / 2 + HZ * scsi_inq_timeout, 3,
					  &exec_args);

		SCSI_LOG_SCAN_BUS(3, sdev_printk(KERN_INFO, sdev,
				"scsi scan: INQUIRY %s with code 0x%x\n",
				result ? "failed" : "successful", result));

		if (result == 0) {
			/*
			 * if nothing was transferred, we try
			 * again. It's a workaround for some USB
			 * devices.
			 */
			if (resid == try_inquiry_len)
				continue;
		}
		break;
	}

	if (result == 0) {
		scsi_sanitize_inquiry_string(&inq_result[8], 8);
		scsi_sanitize_inquiry_string(&inq_result[16], 16);
		scsi_sanitize_inquiry_string(&inq_result[32], 4);

		response_len = inq_result[4] + 5;
		if (response_len > 255)
			response_len = first_inquiry_len;	/* sanity */

		/*
		 * Get any flags for this device.
		 *
		 * XXX add a bflags to scsi_device, and replace the
		 * corresponding bit fields in scsi_device, so bflags
		 * need not be passed as an argument.
		 */
		*bflags = scsi_get_device_flags(sdev, &inq_result[8],
				&inq_result[16]);

		/* When the first pass succeeds we gain information about
		 * what larger transfer lengths might work. */
		if (pass == 1) {
			if (BLIST_INQUIRY_36 & *bflags)
				next_inquiry_len = 36;
			/*
			 * LLD specified a maximum sdev->inquiry_len
			 * but device claims it has more data. Capping
			 * the length only makes sense for legacy
			 * devices. If a device supports SPC-4 (2014)
			 * or newer, assume that it is safe to ask for
			 * as much as the device says it supports.
			 */
			else if (sdev->inquiry_len &&
				 response_len > sdev->inquiry_len &&
				 (inq_result[2] & 0x7) < 6) /* SPC-4 */
				next_inquiry_len = sdev->inquiry_len;
			else
				next_inquiry_len = response_len;

			/* If more data is available perform the second pass */
			if (next_inquiry_len > try_inquiry_len) {
				try_inquiry_len = next_inquiry_len;
				pass = 2;
				goto next_pass;
			}
		}

	} else if (pass == 2) {
		sdev_printk(KERN_INFO, sdev,
			    "scsi scan: %d byte inquiry failed.  "
			    "Consider BLIST_INQUIRY_36 for this device\n",
			    try_inquiry_len);

		/* If this pass failed, the third pass goes back and transfers
		 * the same amount as we successfully got in the first pass. */
		try_inquiry_len = first_inquiry_len;
		pass = 3;
		goto next_pass;
	}

	/* If the last transfer attempt got an error, assume the
	 * peripheral doesn't exist or is dead. */
	if (result)
		return -EIO;

	/* Don't report any more data than the device says is valid */
	sdev->inquiry_len = min(try_inquiry_len, response_len);

	/*
	 * XXX Abort if the response length is less than 36? If less than
	 * 32, the lookup of the device flags (above) could be invalid,
	 * and it would be possible to take an incorrect action - we do
	 * not want to hang because of a short INQUIRY. On the flip side,
	 * if the device is spun down or becoming ready (and so it gives a
	 * short INQUIRY), an abort here prevents any further use of the
	 * device, including spin up.
	 *
	 * On the whole, the best approach seems to be to assume the first
	 * 36 bytes are valid no matter what the device says.  That's
	 * better than copying < 36 bytes to the inquiry-result buffer
	 * and displaying garbage for the Vendor, Product, or Revision
	 * strings.
	 */
	if (sdev->inquiry_len < 36) {
		if (!sdev->host->short_inquiry) {
			shost_printk(KERN_INFO, sdev->host,
				    "scsi scan: INQUIRY result too short (%d),"
				    " using 36\n", sdev->inquiry_len);
			sdev->host->short_inquiry = 1;
		}
		sdev->inquiry_len = 36;
	}

	/*
	 * Related to the above issue:
	 *
	 * XXX Devices (disk or all?) should be sent a TEST UNIT READY,
	 * and if not ready, sent a START_STOP to start (maybe spin up) and
	 * then send the INQUIRY again, since the INQUIRY can change after
	 * a device is initialized.
	 *
	 * Ideally, start a device if explicitly asked to do so.  This
	 * assumes that a device is spun up on power on, spun down on
	 * request, and then spun up on request.
	 */

	/*
	 * The scanning code needs to know the scsi_level, even if no
	 * device is attached at LUN 0 (SCSI_SCAN_TARGET_PRESENT) so
	 * non-zero LUNs can be scanned.
	 */
	sdev->scsi_level = inq_result[2] & 0x0f;
	if (sdev->scsi_level >= 2 ||
	    (sdev->scsi_level == 1 && (inq_result[3] & 0x0f) == 1))
		sdev->scsi_level++;
	sdev->sdev_target->scsi_level = sdev->scsi_level;

	/*
	 * If SCSI-2 or lower, and if the transport requires it,
	 * store the LUN value in CDB[1].
	 */
	sdev->lun_in_cdb = 0;
	if (sdev->scsi_level <= SCSI_2 &&
	    sdev->scsi_level != SCSI_UNKNOWN &&
	    !sdev->host->no_scsi2_lun_in_cdb)
		sdev->lun_in_cdb = 1;

	return 0;
}

/**
 * scsi_add_lun - allocate and fully initialze a scsi_device
 * @sdev:	holds information to be stored in the new scsi_device
 * @inq_result:	holds the result of a previous INQUIRY to the LUN
 * @bflags:	black/white list flag
 * @async:	1 if this device is being scanned asynchronously
 *
 * Description:
 *     Initialize the scsi_device @sdev.  Optionally set fields based
 *     on values in *@bflags.
 *
 * Return:
 *     SCSI_SCAN_NO_RESPONSE: could not allocate or setup a scsi_device
 *     SCSI_SCAN_LUN_PRESENT: a new scsi_device was allocated and initialized
 **/
static int scsi_add_lun(struct scsi_device *sdev, unsigned char *inq_result,
		blist_flags_t *bflags, int async)
{
	const struct scsi_host_template *hostt = sdev->host->hostt;
	struct queue_limits lim;
	int ret;

	/*
	 * XXX do not save the inquiry, since it can change underneath us,
	 * save just vendor/model/rev.
	 *
	 * Rather than save it and have an ioctl that retrieves the saved
	 * value, have an ioctl that executes the same INQUIRY code used
	 * in scsi_probe_lun, let user level programs doing INQUIRY
	 * scanning run at their own risk, or supply a user level program
	 * that can correctly scan.
	 */

	/*
	 * Copy at least 36 bytes of INQUIRY data, so that we don't
	 * dereference unallocated memory when accessing the Vendor,
	 * Product, and Revision strings.  Badly behaved devices may set
	 * the INQUIRY Additional Length byte to a small value, indicating
	 * these strings are invalid, but often they contain plausible data
	 * nonetheless.  It doesn't matter if the device sent < 36 bytes
	 * total, since scsi_probe_lun() initializes inq_result with 0s.
	 */
	sdev->inquiry = kmemdup(inq_result,
				max_t(size_t, sdev->inquiry_len, 36),
				GFP_KERNEL);
	if (sdev->inquiry == NULL)
		return SCSI_SCAN_NO_RESPONSE;

	sdev->vendor = (char *) (sdev->inquiry + 8);
	sdev->model = (char *) (sdev->inquiry + 16);
	sdev->rev = (char *) (sdev->inquiry + 32);

	if (strncmp(sdev->vendor, "ATA     ", 8) == 0) {
		/*
		 * sata emulation layer device.  This is a hack to work around
		 * the SATL power management specifications which state that
		 * when the SATL detects the device has gone into standby
		 * mode, it shall respond with NOT READY.
		 */
		sdev->allow_restart = 1;
	}

	if (*bflags & BLIST_ISROM) {
		sdev->type = TYPE_ROM;
		sdev->removable = 1;
	} else {
		sdev->type = (inq_result[0] & 0x1f);
		sdev->removable = (inq_result[1] & 0x80) >> 7;

		/*
		 * some devices may respond with wrong type for
		 * well-known logical units. Force well-known type
		 * to enumerate them correctly.
		 */
		if (scsi_is_wlun(sdev->lun) && sdev->type != TYPE_WLUN) {
			sdev_printk(KERN_WARNING, sdev,
				"%s: correcting incorrect peripheral device type 0x%x for W-LUN 0x%16xhN\n",
				__func__, sdev->type, (unsigned int)sdev->lun);
			sdev->type = TYPE_WLUN;
		}

	}

	if (sdev->type == TYPE_RBC || sdev->type == TYPE_ROM) {
		/* RBC and MMC devices can return SCSI-3 compliance and yet
		 * still not support REPORT LUNS, so make them act as
		 * BLIST_NOREPORTLUN unless BLIST_REPORTLUN2 is
		 * specifically set */
		if ((*bflags & BLIST_REPORTLUN2) == 0)
			*bflags |= BLIST_NOREPORTLUN;
	}

	/*
	 * For a peripheral qualifier (PQ) value of 1 (001b), the SCSI
	 * spec says: The device server is capable of supporting the
	 * specified peripheral device type on this logical unit. However,
	 * the physical device is not currently connected to this logical
	 * unit.
	 *
	 * The above is vague, as it implies that we could treat 001 and
	 * 011 the same. Stay compatible with previous code, and create a
	 * scsi_device for a PQ of 1
	 *
	 * Don't set the device offline here; rather let the upper
	 * level drivers eval the PQ to decide whether they should
	 * attach. So remove ((inq_result[0] >> 5) & 7) == 1 check.
	 */ 

	sdev->inq_periph_qual = (inq_result[0] >> 5) & 7;
	sdev->lockable = sdev->removable;
	sdev->soft_reset = (inq_result[7] & 1) && ((inq_result[3] & 7) == 2);

	if (sdev->scsi_level >= SCSI_3 ||
			(sdev->inquiry_len > 56 && inq_result[56] & 0x04))
		sdev->ppr = 1;
	if (inq_result[7] & 0x60)
		sdev->wdtr = 1;
	if (inq_result[7] & 0x10)
		sdev->sdtr = 1;

	sdev_printk(KERN_NOTICE, sdev, "%s %.8s %.16s %.4s PQ: %d "
			"ANSI: %d%s\n", scsi_device_type(sdev->type),
			sdev->vendor, sdev->model, sdev->rev,
			sdev->inq_periph_qual, inq_result[2] & 0x07,
			(inq_result[3] & 0x0f) == 1 ? " CCS" : "");

	if ((sdev->scsi_level >= SCSI_2) && (inq_result[7] & 2) &&
	    !(*bflags & BLIST_NOTQ)) {
		sdev->tagged_supported = 1;
		sdev->simple_tags = 1;
	}

	/*
	 * Some devices (Texel CD ROM drives) have handshaking problems
	 * when used with the Seagate controllers. borken is initialized
	 * to 1, and then set it to 0 here.
	 */
	if ((*bflags & BLIST_BORKEN) == 0)
		sdev->borken = 0;

	if (*bflags & BLIST_NO_ULD_ATTACH)
		sdev->no_uld_attach = 1;

	/*
	 * Apparently some really broken devices (contrary to the SCSI
	 * standards) need to be selected without asserting ATN
	 */
	if (*bflags & BLIST_SELECT_NO_ATN)
		sdev->select_no_atn = 1;

	/*
	 * Some devices may not want to have a start command automatically
	 * issued when a device is added.
	 */
	if (*bflags & BLIST_NOSTARTONADD)
		sdev->no_start_on_add = 1;

	if (*bflags & BLIST_SINGLELUN)
		scsi_target(sdev)->single_lun = 1;

	sdev->use_10_for_rw = 1;

	/* some devices don't like REPORT SUPPORTED OPERATION CODES
	 * and will simply timeout causing sd_mod init to take a very
	 * very long time */
	if (*bflags & BLIST_NO_RSOC)
		sdev->no_report_opcodes = 1;

	/* set the device running here so that slave configure
	 * may do I/O */
	mutex_lock(&sdev->state_mutex);
	ret = scsi_device_set_state(sdev, SDEV_RUNNING);
	if (ret)
		ret = scsi_device_set_state(sdev, SDEV_BLOCK);
	mutex_unlock(&sdev->state_mutex);

	if (ret) {
		sdev_printk(KERN_ERR, sdev,
			    "in wrong state %s to complete scan\n",
			    scsi_device_state_name(sdev->sdev_state));
		return SCSI_SCAN_NO_RESPONSE;
	}

	if (*bflags & BLIST_NOT_LOCKABLE)
		sdev->lockable = 0;

	if (*bflags & BLIST_RETRY_HWERROR)
		sdev->retry_hwerror = 1;

	if (*bflags & BLIST_NO_DIF)
		sdev->no_dif = 1;

	if (*bflags & BLIST_UNMAP_LIMIT_WS)
		sdev->unmap_limit_for_ws = 1;

	if (*bflags & BLIST_IGN_MEDIA_CHANGE)
		sdev->ignore_media_change = 1;

	sdev->eh_timeout = SCSI_DEFAULT_EH_TIMEOUT;

	if (*bflags & BLIST_TRY_VPD_PAGES)
		sdev->try_vpd_pages = 1;
	else if (*bflags & BLIST_SKIP_VPD_PAGES)
		sdev->skip_vpd_pages = 1;

	if (*bflags & BLIST_NO_VPD_SIZE)
		sdev->no_vpd_size = 1;

	transport_configure_device(&sdev->sdev_gendev);

	/*
	 * No need to freeze the queue as it isn't reachable to anyone else yet.
	 */
	lim = queue_limits_start_update(sdev->request_queue);
	if (*bflags & BLIST_MAX_512)
		lim.max_hw_sectors = 512;
	else if (*bflags & BLIST_MAX_1024)
		lim.max_hw_sectors = 1024;

	if (hostt->device_configure)
		ret = hostt->device_configure(sdev, &lim);
	else if (hostt->slave_configure)
		ret = hostt->slave_configure(sdev);
	if (ret) {
		queue_limits_cancel_update(sdev->request_queue);
		/*
		 * If the LLDD reports device not present, don't clutter the
		 * console with failure messages.
		 */
		if (ret != -ENXIO)
			sdev_printk(KERN_ERR, sdev,
				"failed to configure device\n");
		return SCSI_SCAN_NO_RESPONSE;
	}

	ret = queue_limits_commit_update(sdev->request_queue, &lim);
	if (ret) {
		sdev_printk(KERN_ERR, sdev, "failed to apply queue limits.\n");
		return SCSI_SCAN_NO_RESPONSE;
	}

	/*
	 * The queue_depth is often changed in ->device_configure.
	 *
	 * Set up budget map again since memory consumption of the map depends
	 * on actual queue depth.
	 */
	if (hostt->device_configure || hostt->slave_configure)
		scsi_realloc_sdev_budget_map(sdev, sdev->queue_depth);

	if (sdev->scsi_level >= SCSI_3)
		scsi_attach_vpd(sdev);

	scsi_cdl_check(sdev);

	sdev->max_queue_depth = sdev->queue_depth;
	WARN_ON_ONCE(sdev->max_queue_depth > sdev->budget_map.depth);
	sdev->sdev_bflags = *bflags;

	/*
	 * Ok, the device is now all set up, we can
	 * register it and tell the rest of the kernel
	 * about it.
	 */
	if (!async && scsi_sysfs_add_sdev(sdev) != 0)
		return SCSI_SCAN_NO_RESPONSE;

	return SCSI_SCAN_LUN_PRESENT;
}

#ifdef CONFIG_SCSI_LOGGING
/** 
 * scsi_inq_str - print INQUIRY data from min to max index, strip trailing whitespace
 * @buf:   Output buffer with at least end-first+1 bytes of space
 * @inq:   Inquiry buffer (input)
 * @first: Offset of string into inq
 * @end:   Index after last character in inq
 */
static unsigned char *scsi_inq_str(unsigned char *buf, unsigned char *inq,
				   unsigned first, unsigned end)
{
	unsigned term = 0, idx;

	for (idx = 0; idx + first < end && idx + first < inq[4] + 5; idx++) {
		if (inq[idx+first] > ' ') {
			buf[idx] = inq[idx+first];
			term = idx+1;
		} else {
			buf[idx] = ' ';
		}
	}
	buf[term] = 0;
	return buf;
}
#endif

/**
 * scsi_probe_and_add_lun - probe a LUN, if a LUN is found add it
 * @starget:	pointer to target device structure
 * @lun:	LUN of target device
 * @bflagsp:	store bflags here if not NULL
 * @sdevp:	probe the LUN corresponding to this scsi_device
 * @rescan:     if not equal to SCSI_SCAN_INITIAL skip some code only
 *              needed on first scan
 * @hostdata:	passed to scsi_alloc_sdev()
 *
 * Description:
 *     Call scsi_probe_lun, if a LUN with an attached device is found,
 *     allocate and set it up by calling scsi_add_lun.
 *
 * Return:
 *
 *   - SCSI_SCAN_NO_RESPONSE: could not allocate or setup a scsi_device
 *   - SCSI_SCAN_TARGET_PRESENT: target responded, but no device is
 *         attached at the LUN
 *   - SCSI_SCAN_LUN_PRESENT: a new scsi_device was allocated and initialized
 **/
static int scsi_probe_and_add_lun(struct scsi_target *starget,
				  u64 lun, blist_flags_t *bflagsp,
				  struct scsi_device **sdevp,
				  enum scsi_scan_mode rescan,
				  void *hostdata)
{
	struct scsi_device *sdev;
	unsigned char *result;
	blist_flags_t bflags;
	int res = SCSI_SCAN_NO_RESPONSE, result_len = 256;
	struct Scsi_Host *shost = dev_to_shost(starget->dev.parent);

	/*
	 * The rescan flag is used as an optimization, the first scan of a
	 * host adapter calls into here with rescan == 0.
	 */
	sdev = scsi_device_lookup_by_target(starget, lun);
	if (sdev) {
		if (rescan != SCSI_SCAN_INITIAL || !scsi_device_created(sdev)) {
			SCSI_LOG_SCAN_BUS(3, sdev_printk(KERN_INFO, sdev,
				"scsi scan: device exists on %s\n",
				dev_name(&sdev->sdev_gendev)));
			if (sdevp)
				*sdevp = sdev;
			else
				scsi_device_put(sdev);

			if (bflagsp)
				*bflagsp = scsi_get_device_flags(sdev,
								 sdev->vendor,
								 sdev->model);
			return SCSI_SCAN_LUN_PRESENT;
		}
		scsi_device_put(sdev);
	} else
		sdev = scsi_alloc_sdev(starget, lun, hostdata);
	if (!sdev)
		goto out;

	result = kmalloc(result_len, GFP_KERNEL);
	if (!result)
		goto out_free_sdev;

	if (scsi_probe_lun(sdev, result, result_len, &bflags))
		goto out_free_result;

	if (bflagsp)
		*bflagsp = bflags;
	/*
	 * result contains valid SCSI INQUIRY data.
	 */
	if ((result[0] >> 5) == 3) {
		/*
		 * For a Peripheral qualifier 3 (011b), the SCSI
		 * spec says: The device server is not capable of
		 * supporting a physical device on this logical
		 * unit.
		 *
		 * For disks, this implies that there is no
		 * logical disk configured at sdev->lun, but there
		 * is a target id responding.
		 */
		SCSI_LOG_SCAN_BUS(2, sdev_printk(KERN_INFO, sdev, "scsi scan:"
				   " peripheral qualifier of 3, device not"
				   " added\n"))
		if (lun == 0) {
			SCSI_LOG_SCAN_BUS(1, {
				unsigned char vend[9];
				unsigned char mod[17];

				sdev_printk(KERN_INFO, sdev,
					"scsi scan: consider passing scsi_mod."
					"dev_flags=%s:%s:0x240 or 0x1000240\n",
					scsi_inq_str(vend, result, 8, 16),
					scsi_inq_str(mod, result, 16, 32));
			});

		}

		res = SCSI_SCAN_TARGET_PRESENT;
		goto out_free_result;
	}

	/*
	 * Some targets may set slight variations of PQ and PDT to signal
	 * that no LUN is present, so don't add sdev in these cases.
	 * Two specific examples are:
	 * 1) NetApp targets: return PQ=1, PDT=0x1f
	 * 2) USB UFI: returns PDT=0x1f, with the PQ bits being "reserved"
	 *    in the UFI 1.0 spec (we cannot rely on reserved bits).
	 *
	 * References:
	 * 1) SCSI SPC-3, pp. 145-146
	 * PQ=1: "A peripheral device having the specified peripheral
	 * device type is not connected to this logical unit. However, the
	 * device server is capable of supporting the specified peripheral
	 * device type on this logical unit."
	 * PDT=0x1f: "Unknown or no device type"
	 * 2) USB UFI 1.0, p. 20
	 * PDT=00h Direct-access device (floppy)
	 * PDT=1Fh none (no FDD connected to the requested logical unit)
	 */
	if (((result[0] >> 5) == 1 || starget->pdt_1f_for_no_lun) &&
	    (result[0] & 0x1f) == 0x1f &&
	    !scsi_is_wlun(lun)) {
		SCSI_LOG_SCAN_BUS(3, sdev_printk(KERN_INFO, sdev,
					"scsi scan: peripheral device type"
					" of 31, no device added\n"));
		res = SCSI_SCAN_TARGET_PRESENT;
		goto out_free_result;
	}

	res = scsi_add_lun(sdev, result, &bflags, shost->async_scan);
	if (res == SCSI_SCAN_LUN_PRESENT) {
		if (bflags & BLIST_KEY) {
			sdev->lockable = 0;
			scsi_unlock_floptical(sdev, result);
		}
	}

 out_free_result:
	kfree(result);
 out_free_sdev:
	if (res == SCSI_SCAN_LUN_PRESENT) {
		if (sdevp) {
			if (scsi_device_get(sdev) == 0) {
				*sdevp = sdev;
			} else {
				__scsi_remove_device(sdev);
				res = SCSI_SCAN_NO_RESPONSE;
			}
		}
	} else
		__scsi_remove_device(sdev);
 out:
	return res;
}

/**
 * scsi_sequential_lun_scan - sequentially scan a SCSI target
 * @starget:	pointer to target structure to scan
 * @bflags:	black/white list flag for LUN 0
 * @scsi_level: Which version of the standard does this device adhere to
 * @rescan:     passed to scsi_probe_add_lun()
 *
 * Description:
 *     Generally, scan from LUN 1 (LUN 0 is assumed to already have been
 *     scanned) to some maximum lun until a LUN is found with no device
 *     attached. Use the bflags to figure out any oddities.
 *
 *     Modifies sdevscan->lun.
 **/
static void scsi_sequential_lun_scan(struct scsi_target *starget,
				     blist_flags_t bflags, int scsi_level,
				     enum scsi_scan_mode rescan)
{
	uint max_dev_lun;
	u64 sparse_lun, lun;
	struct Scsi_Host *shost = dev_to_shost(starget->dev.parent);

	SCSI_LOG_SCAN_BUS(3, starget_printk(KERN_INFO, starget,
		"scsi scan: Sequential scan\n"));

	max_dev_lun = min(max_scsi_luns, shost->max_lun);
	/*
	 * If this device is known to support sparse multiple units,
	 * override the other settings, and scan all of them. Normally,
	 * SCSI-3 devices should be scanned via the REPORT LUNS.
	 */
	if (bflags & BLIST_SPARSELUN) {
		max_dev_lun = shost->max_lun;
		sparse_lun = 1;
	} else
		sparse_lun = 0;

	/*
	 * If less than SCSI_1_CCS, and no special lun scanning, stop
	 * scanning; this matches 2.4 behaviour, but could just be a bug
	 * (to continue scanning a SCSI_1_CCS device).
	 *
	 * This test is broken.  We might not have any device on lun0 for
	 * a sparselun device, and if that's the case then how would we
	 * know the real scsi_level, eh?  It might make sense to just not
	 * scan any SCSI_1 device for non-0 luns, but that check would best
	 * go into scsi_alloc_sdev() and just have it return null when asked
	 * to alloc an sdev for lun > 0 on an already found SCSI_1 device.
	 *
	if ((sdevscan->scsi_level < SCSI_1_CCS) &&
	    ((bflags & (BLIST_FORCELUN | BLIST_SPARSELUN | BLIST_MAX5LUN))
	     == 0))
		return;
	 */
	/*
	 * If this device is known to support multiple units, override
	 * the other settings, and scan all of them.
	 */
	if (bflags & BLIST_FORCELUN)
		max_dev_lun = shost->max_lun;
	/*
	 * REGAL CDC-4X: avoid hang after LUN 4
	 */
	if (bflags & BLIST_MAX5LUN)
		max_dev_lun = min(5U, max_dev_lun);
	/*
	 * Do not scan SCSI-2 or lower device past LUN 7, unless
	 * BLIST_LARGELUN.
	 */
	if (scsi_level < SCSI_3 && !(bflags & BLIST_LARGELUN))
		max_dev_lun = min(8U, max_dev_lun);
	else
		max_dev_lun = min(256U, max_dev_lun);

	/*
	 * We have already scanned LUN 0, so start at LUN 1. Keep scanning
	 * until we reach the max, or no LUN is found and we are not
	 * sparse_lun.
	 */
	for (lun = 1; lun < max_dev_lun; ++lun)
		if ((scsi_probe_and_add_lun(starget, lun, NULL, NULL, rescan,
					    NULL) != SCSI_SCAN_LUN_PRESENT) &&
		    !sparse_lun)
			return;
}

/**
 * scsi_report_lun_scan - Scan using SCSI REPORT LUN results
 * @starget: which target
 * @bflags: Zero or a mix of BLIST_NOLUN, BLIST_REPORTLUN2, or BLIST_NOREPORTLUN
 * @rescan: nonzero if we can skip code only needed on first scan
 *
 * Description:
 *   Fast scanning for modern (SCSI-3) devices by sending a REPORT LUN command.
 *   Scan the resulting list of LUNs by calling scsi_probe_and_add_lun.
 *
 *   If BLINK_REPORTLUN2 is set, scan a target that supports more than 8
 *   LUNs even if it's older than SCSI-3.
 *   If BLIST_NOREPORTLUN is set, return 1 always.
 *   If BLIST_NOLUN is set, return 0 always.
 *   If starget->no_report_luns is set, return 1 always.
 *
 * Return:
 *     0: scan completed (or no memory, so further scanning is futile)
 *     1: could not scan with REPORT LUN
 **/
static int scsi_report_lun_scan(struct scsi_target *starget, blist_flags_t bflags,
				enum scsi_scan_mode rescan)
{
	unsigned char scsi_cmd[MAX_COMMAND_SIZE];
	unsigned int length;
	u64 lun;
	unsigned int num_luns;
	int result;
	struct scsi_lun *lunp, *lun_data;
	struct scsi_device *sdev;
	struct Scsi_Host *shost = dev_to_shost(&starget->dev);
	struct scsi_failure failure_defs[] = {
		{
			.sense = UNIT_ATTENTION,
			.asc = SCMD_FAILURE_ASC_ANY,
			.ascq = SCMD_FAILURE_ASCQ_ANY,
			.result = SAM_STAT_CHECK_CONDITION,
		},
		/* Fail all CCs except the UA above */
		{
			.sense = SCMD_FAILURE_SENSE_ANY,
			.result = SAM_STAT_CHECK_CONDITION,
		},
		/* Retry any other errors not listed above */
		{
			.result = SCMD_FAILURE_RESULT_ANY,
		},
		{}
	};
	struct scsi_failures failures = {
		.total_allowed = 3,
		.failure_definitions = failure_defs,
	};
	const struct scsi_exec_args exec_args = {
		.failures = &failures,
	};
	int ret = 0;

	/*
	 * Only support SCSI-3 and up devices if BLIST_NOREPORTLUN is not set.
	 * Also allow SCSI-2 if BLIST_REPORTLUN2 is set and host adapter does
	 * support more than 8 LUNs.
	 * Don't attempt if the target doesn't support REPORT LUNS.
	 */
	if (bflags & BLIST_NOREPORTLUN)
		return 1;
	if (starget->scsi_level < SCSI_2 &&
	    starget->scsi_level != SCSI_UNKNOWN)
		return 1;
	if (starget->scsi_level < SCSI_3 &&
	    (!(bflags & BLIST_REPORTLUN2) || shost->max_lun <= 8))
		return 1;
	if (bflags & BLIST_NOLUN)
		return 0;
	if (starget->no_report_luns)
		return 1;

	if (!(sdev = scsi_device_lookup_by_target(starget, 0))) {
		sdev = scsi_alloc_sdev(starget, 0, NULL);
		if (!sdev)
			return 0;
		if (scsi_device_get(sdev)) {
			__scsi_remove_device(sdev);
			return 0;
		}
	}

	/*
	 * Allocate enough to hold the header (the same size as one scsi_lun)
	 * plus the number of luns we are requesting.  511 was the default
	 * value of the now removed max_report_luns parameter.
	 */
	length = (511 + 1) * sizeof(struct scsi_lun);
retry:
	lun_data = kmalloc(length, GFP_KERNEL);
	if (!lun_data) {
		printk(ALLOC_FAILURE_MSG, __func__);
		goto out;
	}

	scsi_cmd[0] = REPORT_LUNS;

	/*
	 * bytes 1 - 5: reserved, set to zero.
	 */
	memset(&scsi_cmd[1], 0, 5);

	/*
	 * bytes 6 - 9: length of the command.
	 */
	put_unaligned_be32(length, &scsi_cmd[6]);

	scsi_cmd[10] = 0;	/* reserved */
	scsi_cmd[11] = 0;	/* control */

	/*
	 * We can get a UNIT ATTENTION, for example a power on/reset, so
	 * retry a few times (like sd.c does for TEST UNIT READY).
	 * Experience shows some combinations of adapter/devices get at
	 * least two power on/resets.
	 *
	 * Illegal requests (for devices that do not support REPORT LUNS)
	 * should come through as a check condition, and will not generate
	 * a retry.
	 */
	scsi_failures_reset_retries(&failures);

	SCSI_LOG_SCAN_BUS(3, sdev_printk (KERN_INFO, sdev,
			  "scsi scan: Sending REPORT LUNS\n"));

	result = scsi_execute_cmd(sdev, scsi_cmd, REQ_OP_DRV_IN, lun_data,
				  length, SCSI_REPORT_LUNS_TIMEOUT, 3,
				  &exec_args);

	SCSI_LOG_SCAN_BUS(3, sdev_printk (KERN_INFO, sdev,
			  "scsi scan: REPORT LUNS  %s result 0x%x\n",
			  result ?  "failed" : "successful", result));
	if (result) {
		/*
		 * The device probably does not support a REPORT LUN command
		 */
		ret = 1;
		goto out_err;
	}

	/*
	 * Get the length from the first four bytes of lun_data.
	 */
	if (get_unaligned_be32(lun_data->scsi_lun) +
	    sizeof(struct scsi_lun) > length) {
		length = get_unaligned_be32(lun_data->scsi_lun) +
			 sizeof(struct scsi_lun);
		kfree(lun_data);
		goto retry;
	}
	length = get_unaligned_be32(lun_data->scsi_lun);

	num_luns = (length / sizeof(struct scsi_lun));

	SCSI_LOG_SCAN_BUS(3, sdev_printk (KERN_INFO, sdev,
		"scsi scan: REPORT LUN scan\n"));

	/*
	 * Scan the luns in lun_data. The entry at offset 0 is really
	 * the header, so start at 1 and go up to and including num_luns.
	 */
	for (lunp = &lun_data[1]; lunp <= &lun_data[num_luns]; lunp++) {
		lun = scsilun_to_int(lunp);

		if (lun > sdev->host->max_lun) {
			sdev_printk(KERN_WARNING, sdev,
				    "lun%llu has a LUN larger than"
				    " allowed by the host adapter\n", lun);
		} else {
			int res;

			res = scsi_probe_and_add_lun(starget,
				lun, NULL, NULL, rescan, NULL);
			if (res == SCSI_SCAN_NO_RESPONSE) {
				/*
				 * Got some results, but now none, abort.
				 */
				sdev_printk(KERN_ERR, sdev,
					"Unexpected response"
					" from lun %llu while scanning, scan"
					" aborted\n", (unsigned long long)lun);
				break;
			}
		}
	}

 out_err:
	kfree(lun_data);
 out:
	if (scsi_device_created(sdev))
		/*
		 * the sdev we used didn't appear in the report luns scan
		 */
		__scsi_remove_device(sdev);
	scsi_device_put(sdev);
	return ret;
}

struct scsi_device *__scsi_add_device(struct Scsi_Host *shost, uint channel,
				      uint id, u64 lun, void *hostdata)
{
	struct scsi_device *sdev = ERR_PTR(-ENODEV);
	struct device *parent = &shost->shost_gendev;
	struct scsi_target *starget;

	if (strncmp(scsi_scan_type, "none", 4) == 0)
		return ERR_PTR(-ENODEV);

	starget = scsi_alloc_target(parent, channel, id);
	if (!starget)
		return ERR_PTR(-ENOMEM);
	scsi_autopm_get_target(starget);

	mutex_lock(&shost->scan_mutex);
	if (!shost->async_scan)
		scsi_complete_async_scans();

	if (scsi_host_scan_allowed(shost) && scsi_autopm_get_host(shost) == 0) {
		scsi_probe_and_add_lun(starget, lun, NULL, &sdev,
				       SCSI_SCAN_RESCAN, hostdata);
		scsi_autopm_put_host(shost);
	}
	mutex_unlock(&shost->scan_mutex);
	scsi_autopm_put_target(starget);
	/*
	 * paired with scsi_alloc_target().  Target will be destroyed unless
	 * scsi_probe_and_add_lun made an underlying device visible
	 */
	scsi_target_reap(starget);
	put_device(&starget->dev);

	return sdev;
}
EXPORT_SYMBOL(__scsi_add_device);

int scsi_add_device(struct Scsi_Host *host, uint channel,
		    uint target, u64 lun)
{
	struct scsi_device *sdev = 
		__scsi_add_device(host, channel, target, lun, NULL);
	if (IS_ERR(sdev))
		return PTR_ERR(sdev);

	scsi_device_put(sdev);
	return 0;
}
EXPORT_SYMBOL(scsi_add_device);

int scsi_resume_device(struct scsi_device *sdev)
{
	struct device *dev = &sdev->sdev_gendev;
	int ret = 0;

	device_lock(dev);

	/*
	 * Bail out if the device or its queue are not running. Otherwise,
	 * the rescan may block waiting for commands to be executed, with us
	 * holding the device lock. This can result in a potential deadlock
	 * in the power management core code when system resume is on-going.
	 */
	if (sdev->sdev_state != SDEV_RUNNING ||
	    blk_queue_pm_only(sdev->request_queue)) {
		ret = -EWOULDBLOCK;
		goto unlock;
	}

	if (dev->driver && try_module_get(dev->driver->owner)) {
		struct scsi_driver *drv = to_scsi_driver(dev->driver);

		if (drv->resume)
			ret = drv->resume(dev);
		module_put(dev->driver->owner);
	}

unlock:
	device_unlock(dev);

	return ret;
}
EXPORT_SYMBOL(scsi_resume_device);

int scsi_rescan_device(struct scsi_device *sdev)
{
	struct device *dev = &sdev->sdev_gendev;
	int ret = 0;

	device_lock(dev);

	/*
	 * Bail out if the device or its queue are not running. Otherwise,
	 * the rescan may block waiting for commands to be executed, with us
	 * holding the device lock. This can result in a potential deadlock
	 * in the power management core code when system resume is on-going.
	 */
	if (sdev->sdev_state != SDEV_RUNNING ||
	    blk_queue_pm_only(sdev->request_queue)) {
		ret = -EWOULDBLOCK;
		goto unlock;
	}

	scsi_attach_vpd(sdev);
	scsi_cdl_check(sdev);

	if (sdev->handler && sdev->handler->rescan)
		sdev->handler->rescan(sdev);

	if (dev->driver && try_module_get(dev->driver->owner)) {
		struct scsi_driver *drv = to_scsi_driver(dev->driver);

		if (drv->rescan)
			drv->rescan(dev);
		module_put(dev->driver->owner);
	}

unlock:
	device_unlock(dev);

	return ret;
}
EXPORT_SYMBOL(scsi_rescan_device);

static void __scsi_scan_target(struct device *parent, unsigned int channel,
		unsigned int id, u64 lun, enum scsi_scan_mode rescan)
{
	struct Scsi_Host *shost = dev_to_shost(parent);
	blist_flags_t bflags = 0;
	int res;
	struct scsi_target *starget;

	if (shost->this_id == id)
		/*
		 * Don't scan the host adapter
		 */
		return;

	starget = scsi_alloc_target(parent, channel, id);
	if (!starget)
		return;
	scsi_autopm_get_target(starget);

	if (lun != SCAN_WILD_CARD) {
		/*
		 * Scan for a specific host/chan/id/lun.
		 */
		scsi_probe_and_add_lun(starget, lun, NULL, NULL, rescan, NULL);
		goto out_reap;
	}

	/*
	 * Scan LUN 0, if there is some response, scan further. Ideally, we
	 * would not configure LUN 0 until all LUNs are scanned.
	 */
	res = scsi_probe_and_add_lun(starget, 0, &bflags, NULL, rescan, NULL);
	if (res == SCSI_SCAN_LUN_PRESENT || res == SCSI_SCAN_TARGET_PRESENT) {
		if (scsi_report_lun_scan(starget, bflags, rescan) != 0)
			/*
			 * The REPORT LUN did not scan the target,
			 * do a sequential scan.
			 */
			scsi_sequential_lun_scan(starget, bflags,
						 starget->scsi_level, rescan);
	}

 out_reap:
	scsi_autopm_put_target(starget);
	/*
	 * paired with scsi_alloc_target(): determine if the target has
	 * any children at all and if not, nuke it
	 */
	scsi_target_reap(starget);

	put_device(&starget->dev);
}

/**
 * scsi_scan_target - scan a target id, possibly including all LUNs on the target.
 * @parent:	host to scan
 * @channel:	channel to scan
 * @id:		target id to scan
 * @lun:	Specific LUN to scan or SCAN_WILD_CARD
 * @rescan:	passed to LUN scanning routines; SCSI_SCAN_INITIAL for
 *              no rescan, SCSI_SCAN_RESCAN to rescan existing LUNs,
 *              and SCSI_SCAN_MANUAL to force scanning even if
 *              'scan=manual' is set.
 *
 * Description:
 *     Scan the target id on @parent, @channel, and @id. Scan at least LUN 0,
 *     and possibly all LUNs on the target id.
 *
 *     First try a REPORT LUN scan, if that does not scan the target, do a
 *     sequential scan of LUNs on the target id.
 **/
void scsi_scan_target(struct device *parent, unsigned int channel,
		      unsigned int id, u64 lun, enum scsi_scan_mode rescan)
{
	struct Scsi_Host *shost = dev_to_shost(parent);

	if (strncmp(scsi_scan_type, "none", 4) == 0)
		return;

	if (rescan != SCSI_SCAN_MANUAL &&
	    strncmp(scsi_scan_type, "manual", 6) == 0)
		return;

	mutex_lock(&shost->scan_mutex);
	if (!shost->async_scan)
		scsi_complete_async_scans();

	if (scsi_host_scan_allowed(shost) && scsi_autopm_get_host(shost) == 0) {
		__scsi_scan_target(parent, channel, id, lun, rescan);
		scsi_autopm_put_host(shost);
	}
	mutex_unlock(&shost->scan_mutex);
}
EXPORT_SYMBOL(scsi_scan_target);

static void scsi_scan_channel(struct Scsi_Host *shost, unsigned int channel,
			      unsigned int id, u64 lun,
			      enum scsi_scan_mode rescan)
{
	uint order_id;

	if (id == SCAN_WILD_CARD)
		for (id = 0; id < shost->max_id; ++id) {
			/*
			 * XXX adapter drivers when possible (FCP, iSCSI)
			 * could modify max_id to match the current max,
			 * not the absolute max.
			 *
			 * XXX add a shost id iterator, so for example,
			 * the FC ID can be the same as a target id
			 * without a huge overhead of sparse id's.
			 */
			if (shost->reverse_ordering)
				/*
				 * Scan from high to low id.
				 */
				order_id = shost->max_id - id - 1;
			else
				order_id = id;
			__scsi_scan_target(&shost->shost_gendev, channel,
					order_id, lun, rescan);
		}
	else
		__scsi_scan_target(&shost->shost_gendev, channel,
				id, lun, rescan);
}

int scsi_scan_host_selected(struct Scsi_Host *shost, unsigned int channel,
			    unsigned int id, u64 lun,
			    enum scsi_scan_mode rescan)
{
	SCSI_LOG_SCAN_BUS(3, shost_printk (KERN_INFO, shost,
		"%s: <%u:%u:%llu>\n",
		__func__, channel, id, lun));

	if (((channel != SCAN_WILD_CARD) && (channel > shost->max_channel)) ||
	    ((id != SCAN_WILD_CARD) && (id >= shost->max_id)) ||
	    ((lun != SCAN_WILD_CARD) && (lun >= shost->max_lun)))
		return -EINVAL;

	mutex_lock(&shost->scan_mutex);
	if (!shost->async_scan)
		scsi_complete_async_scans();

	if (scsi_host_scan_allowed(shost) && scsi_autopm_get_host(shost) == 0) {
		if (channel == SCAN_WILD_CARD)
			for (channel = 0; channel <= shost->max_channel;
			     channel++)
				scsi_scan_channel(shost, channel, id, lun,
						  rescan);
		else
			scsi_scan_channel(shost, channel, id, lun, rescan);
		scsi_autopm_put_host(shost);
	}
	mutex_unlock(&shost->scan_mutex);

	return 0;
}

static void scsi_sysfs_add_devices(struct Scsi_Host *shost)
{
	struct scsi_device *sdev;
	shost_for_each_device(sdev, shost) {
		/* target removed before the device could be added */
		if (sdev->sdev_state == SDEV_DEL)
			continue;
		/* If device is already visible, skip adding it to sysfs */
		if (sdev->is_visible)
			continue;
		if (!scsi_host_scan_allowed(shost) ||
		    scsi_sysfs_add_sdev(sdev) != 0)
			__scsi_remove_device(sdev);
	}
}

/**
 * scsi_prep_async_scan - prepare for an async scan
 * @shost: the host which will be scanned
 * Returns: a cookie to be passed to scsi_finish_async_scan()
 *
 * Tells the midlayer this host is going to do an asynchronous scan.
 * It reserves the host's position in the scanning list and ensures
 * that other asynchronous scans started after this one won't affect the
 * ordering of the discovered devices.
 */
static struct async_scan_data *scsi_prep_async_scan(struct Scsi_Host *shost)
{
	struct async_scan_data *data = NULL;
	unsigned long flags;

	if (strncmp(scsi_scan_type, "sync", 4) == 0)
		return NULL;

	mutex_lock(&shost->scan_mutex);
	if (shost->async_scan) {
		shost_printk(KERN_DEBUG, shost, "%s called twice\n", __func__);
		goto err;
	}

	data = kmalloc(sizeof(*data), GFP_KERNEL);
	if (!data)
		goto err;
	data->shost = scsi_host_get(shost);
	if (!data->shost)
		goto err;
	init_completion(&data->prev_finished);

	spin_lock_irqsave(shost->host_lock, flags);
	shost->async_scan = 1;
	spin_unlock_irqrestore(shost->host_lock, flags);
	mutex_unlock(&shost->scan_mutex);

	spin_lock(&async_scan_lock);
	if (list_empty(&scanning_hosts))
		complete(&data->prev_finished);
	list_add_tail(&data->list, &scanning_hosts);
	spin_unlock(&async_scan_lock);

	return data;

 err:
	mutex_unlock(&shost->scan_mutex);
	kfree(data);
	return NULL;
}

/**
 * scsi_finish_async_scan - asynchronous scan has finished
 * @data: cookie returned from earlier call to scsi_prep_async_scan()
 *
 * All the devices currently attached to this host have been found.
 * This function announces all the devices it has found to the rest
 * of the system.
 */
static void scsi_finish_async_scan(struct async_scan_data *data)
{
	struct Scsi_Host *shost;
	unsigned long flags;

	if (!data)
		return;

	shost = data->shost;

	mutex_lock(&shost->scan_mutex);

	if (!shost->async_scan) {
		shost_printk(KERN_INFO, shost, "%s called twice\n", __func__);
		dump_stack();
		mutex_unlock(&shost->scan_mutex);
		return;
	}

	wait_for_completion(&data->prev_finished);

	scsi_sysfs_add_devices(shost);

	spin_lock_irqsave(shost->host_lock, flags);
	shost->async_scan = 0;
	spin_unlock_irqrestore(shost->host_lock, flags);

	mutex_unlock(&shost->scan_mutex);

	spin_lock(&async_scan_lock);
	list_del(&data->list);
	if (!list_empty(&scanning_hosts)) {
		struct async_scan_data *next = list_entry(scanning_hosts.next,
				struct async_scan_data, list);
		complete(&next->prev_finished);
	}
	spin_unlock(&async_scan_lock);

	scsi_autopm_put_host(shost);
	scsi_host_put(shost);
	kfree(data);
}

static void do_scsi_scan_host(struct Scsi_Host *shost)
{
	if (shost->hostt->scan_finished) {
		unsigned long start = jiffies;
		if (shost->hostt->scan_start)
			shost->hostt->scan_start(shost);

		while (!shost->hostt->scan_finished(shost, jiffies - start))
			msleep(10);
	} else {
		scsi_scan_host_selected(shost, SCAN_WILD_CARD, SCAN_WILD_CARD,
				SCAN_WILD_CARD, SCSI_SCAN_INITIAL);
	}
}

static void do_scan_async(void *_data, async_cookie_t c)
{
	struct async_scan_data *data = _data;
	struct Scsi_Host *shost = data->shost;

	do_scsi_scan_host(shost);
	scsi_finish_async_scan(data);
}

/**
 * scsi_scan_host - scan the given adapter
 * @shost:	adapter to scan
 **/
void scsi_scan_host(struct Scsi_Host *shost)
{
	struct async_scan_data *data;

	if (strncmp(scsi_scan_type, "none", 4) == 0 ||
	    strncmp(scsi_scan_type, "manual", 6) == 0)
		return;
	if (scsi_autopm_get_host(shost) < 0)
		return;

	data = scsi_prep_async_scan(shost);
	if (!data) {
		do_scsi_scan_host(shost);
		scsi_autopm_put_host(shost);
		return;
	}

	/* register with the async subsystem so wait_for_device_probe()
	 * will flush this work
	 */
	async_schedule(do_scan_async, data);

	/* scsi_autopm_put_host(shost) is called in scsi_finish_async_scan() */
}
EXPORT_SYMBOL(scsi_scan_host);

void scsi_forget_host(struct Scsi_Host *shost)
{
	struct scsi_device *sdev;
	unsigned long flags;

 restart:
	spin_lock_irqsave(shost->host_lock, flags);
	list_for_each_entry(sdev, &shost->__devices, siblings) {
		if (sdev->sdev_state == SDEV_DEL)
			continue;
		spin_unlock_irqrestore(shost->host_lock, flags);
		__scsi_remove_device(sdev);
		goto restart;
	}
	spin_unlock_irqrestore(shost->host_lock, flags);
}