blob: a2c6eea9871d534d0da58b2a01e007dbe2ce337b [file] [log] [blame]
# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/clock/idt,versaclock5.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: IDT VersaClock 5 and 6 programmable I2C clock generators
description: |
The IDT VersaClock 5 and VersaClock 6 are programmable I2C
clock generators providing from 3 to 12 output clocks.
When referencing the provided clock in the DT using phandle and clock
specifier, the following mapping applies:
- 5P49V5923:
0 -- OUT0_SEL_I2CB
1 -- OUT1
2 -- OUT2
- 5P49V5933:
0 -- OUT0_SEL_I2CB
1 -- OUT1
2 -- OUT4
- other parts:
0 -- OUT0_SEL_I2CB
1 -- OUT1
2 -- OUT2
3 -- OUT3
4 -- OUT4
The idt,shutdown and idt,output-enable-active properties control the
SH (en_global_shutdown) and SP bits of the Primary Source and Shutdown
Register, respectively. Their behavior is summarized by the following
table:
SH SP Output when the SD/OE pin is Low/High
== == =====================================
0 0 Active/Inactive
0 1 Inactive/Active
1 0 Active/Shutdown
1 1 Inactive/Shutdown
The case where SH and SP are both 1 is likely not very interesting.
maintainers:
- Luca Ceresoli <luca.ceresoli@bootlin.com>
properties:
compatible:
enum:
- idt,5p49v5923
- idt,5p49v5925
- idt,5p49v5933
- idt,5p49v5935
- idt,5p49v60
- idt,5p49v6901
- idt,5p49v6965
- idt,5p49v6975
reg:
description: I2C device address
enum: [ 0x68, 0x6a ]
'#clock-cells':
const: 1
clock-names:
minItems: 1
maxItems: 2
items:
enum: [ xin, clkin ]
clocks:
minItems: 1
maxItems: 2
idt,xtal-load-femtofarads:
minimum: 9000
maximum: 22760
description: Optional load capacitor for XTAL1 and XTAL2
idt,shutdown:
$ref: /schemas/types.yaml#/definitions/uint32
enum: [0, 1]
description: |
If 1, this enables the shutdown functionality: the chip will be
shut down if the SD/OE pin is driven high. If 0, this disables the
shutdown functionality: the chip will never be shut down based on
the value of the SD/OE pin. This property corresponds to the SH
bit of the Primary Source and Shutdown Register.
idt,output-enable-active:
$ref: /schemas/types.yaml#/definitions/uint32
enum: [0, 1]
description: |
If 1, this enables output when the SD/OE pin is high, and disables
output when the SD/OE pin is low. If 0, this disables output when
the SD/OE pin is high, and enables output when the SD/OE pin is
low. This corresponds to the SP bit of the Primary Source and
Shutdown Register.
patternProperties:
"^OUT[1-4]$":
type: object
description:
Description of one of the outputs (OUT1..OUT4). See "Clock1 Output
Configuration" in the Versaclock 5/6/6E Family Register Description
and Programming Guide.
properties:
idt,mode:
description:
The output drive mode. Values defined in dt-bindings/clock/versaclock.h
$ref: /schemas/types.yaml#/definitions/uint32
minimum: 0
maximum: 6
idt,voltage-microvolt:
description: The output drive voltage.
enum: [ 1800000, 2500000, 3300000 ]
idt,slew-percent:
description: The Slew rate control for CMOS single-ended.
enum: [ 80, 85, 90, 100 ]
additionalProperties: false
required:
- compatible
- reg
- '#clock-cells'
- idt,shutdown
- idt,output-enable-active
allOf:
- if:
properties:
compatible:
enum:
- idt,5p49v5933
- idt,5p49v5935
- idt,5p49v6975
then:
# Devices with builtin crystal + optional external input
properties:
clock-names:
const: clkin
clocks:
maxItems: 1
else:
# Devices without builtin crystal
required:
- clock-names
- clocks
additionalProperties: false
examples:
- |
#include <dt-bindings/clock/versaclock.h>
/* 25MHz reference crystal */
ref25: ref25m {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <25000000>;
};
i2c@0 {
reg = <0x0 0x100>;
#address-cells = <1>;
#size-cells = <0>;
/* IDT 5P49V5923 I2C clock generator */
vc5: clock-generator@6a {
compatible = "idt,5p49v5923";
reg = <0x6a>;
#clock-cells = <1>;
/* Connect XIN input to 25MHz reference */
clocks = <&ref25m>;
clock-names = "xin";
/* Set the SD/OE pin's settings */
idt,shutdown = <0>;
idt,output-enable-active = <0>;
OUT1 {
idt,mode = <VC5_CMOSD>;
idt,voltage-microvolt = <1800000>;
idt,slew-percent = <80>;
};
OUT4 {
idt,mode = <VC5_LVDS>;
};
};
};
...