| // SPDX-License-Identifier: (GPL-2.0 OR MIT) |
| /* |
| * Copyright (C) 2023 MediaTek Inc. |
| * Author: Ben Lok <ben.lok@mediatek.com> |
| * Macpaul Lin <macpaul.lin@mediatek.com> |
| */ |
| /dts-v1/; |
| |
| #include "mt8195.dtsi" |
| #include "mt6359.dtsi" |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/input/input.h> |
| #include <dt-bindings/interrupt-controller/irq.h> |
| #include <dt-bindings/pinctrl/mt8195-pinfunc.h> |
| #include <dt-bindings/regulator/mediatek,mt6360-regulator.h> |
| #include <dt-bindings/spmi/spmi.h> |
| #include <dt-bindings/usb/pd.h> |
| |
| / { |
| model = "MediaTek Genio 1200 EVK-P1V2-EMMC"; |
| compatible = "mediatek,mt8395-evk", "mediatek,mt8395", |
| "mediatek,mt8195"; |
| |
| aliases { |
| serial0 = &uart0; |
| ethernet0 = ð |
| }; |
| |
| chosen { |
| stdout-path = "serial0:921600n8"; |
| }; |
| |
| firmware { |
| optee { |
| compatible = "linaro,optee-tz"; |
| method = "smc"; |
| }; |
| }; |
| |
| memory@40000000 { |
| device_type = "memory"; |
| reg = <0 0x40000000 0x2 0x00000000>; |
| }; |
| |
| reserved-memory { |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| |
| /* |
| * 12 MiB reserved for OP-TEE (BL32) |
| * +-----------------------+ 0x43e0_0000 |
| * | SHMEM 2MiB | |
| * +-----------------------+ 0x43c0_0000 |
| * | | TA_RAM 8MiB | |
| * + TZDRAM +--------------+ 0x4340_0000 |
| * | | TEE_RAM 2MiB | |
| * +-----------------------+ 0x4320_0000 |
| */ |
| optee_reserved: optee@43200000 { |
| no-map; |
| reg = <0 0x43200000 0 0x00c00000>; |
| }; |
| |
| scp_mem: memory@50000000 { |
| compatible = "shared-dma-pool"; |
| reg = <0 0x50000000 0 0x2900000>; |
| no-map; |
| }; |
| |
| vpu_mem: memory@53000000 { |
| compatible = "shared-dma-pool"; |
| reg = <0 0x53000000 0 0x1400000>; /* 20 MB */ |
| }; |
| |
| /* 2 MiB reserved for ARM Trusted Firmware (BL31) */ |
| bl31_secmon_mem: memory@54600000 { |
| no-map; |
| reg = <0 0x54600000 0x0 0x200000>; |
| }; |
| |
| snd_dma_mem: memory@60000000 { |
| compatible = "shared-dma-pool"; |
| reg = <0 0x60000000 0 0x1100000>; |
| no-map; |
| }; |
| |
| apu_mem: memory@62000000 { |
| compatible = "shared-dma-pool"; |
| reg = <0 0x62000000 0 0x1400000>; /* 20 MB */ |
| }; |
| }; |
| |
| backlight_lcd0: backlight-lcd0 { |
| compatible = "pwm-backlight"; |
| pwms = <&disp_pwm0 0 500000>; |
| enable-gpios = <&pio 47 GPIO_ACTIVE_HIGH>; |
| brightness-levels = <0 1023>; |
| num-interpolated-steps = <1023>; |
| default-brightness-level = <576>; |
| }; |
| |
| backlight_lcd1: backlight-lcd1 { |
| compatible = "pwm-backlight"; |
| pwms = <&disp_pwm1 0 500000>; |
| enable-gpios = <&pio 46 GPIO_ACTIVE_HIGH>; |
| brightness-levels = <0 1023>; |
| num-interpolated-steps = <1023>; |
| default-brightness-level = <576>; |
| }; |
| |
| can_clk: can-clk { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <20000000>; |
| clock-output-names = "can-clk"; |
| }; |
| |
| edp_panel_fixed_3v3: regulator-0 { |
| compatible = "regulator-fixed"; |
| regulator-name = "edp_panel_3v3"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| enable-active-high; |
| gpio = <&pio 6 GPIO_ACTIVE_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&edp_panel_3v3_en_pins>; |
| }; |
| |
| edp_panel_fixed_12v: regulator-1 { |
| compatible = "regulator-fixed"; |
| regulator-name = "edp_backlight_12v"; |
| regulator-min-microvolt = <12000000>; |
| regulator-max-microvolt = <12000000>; |
| enable-active-high; |
| gpio = <&pio 96 GPIO_ACTIVE_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&edp_panel_12v_en_pins>; |
| }; |
| |
| keys: gpio-keys { |
| compatible = "gpio-keys"; |
| |
| button-volume-up { |
| wakeup-source; |
| debounce-interval = <100>; |
| gpios = <&pio 106 GPIO_ACTIVE_LOW>; |
| label = "volume_up"; |
| linux,code = <KEY_VOLUMEUP>; |
| }; |
| }; |
| |
| wifi_fixed_3v3: regulator-2 { |
| compatible = "regulator-fixed"; |
| regulator-name = "wifi_3v3"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| gpio = <&pio 135 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| regulator-always-on; |
| }; |
| }; |
| |
| &disp_pwm0 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pwm0_default_pins>; |
| status = "okay"; |
| }; |
| |
| &dmic_codec { |
| wakeup-delay-ms = <200>; |
| }; |
| |
| ð { |
| phy-mode ="rgmii-rxid"; |
| phy-handle = <ð_phy0>; |
| snps,reset-gpio = <&pio 93 GPIO_ACTIVE_HIGH>; |
| snps,reset-delays-us = <0 10000 10000>; |
| mediatek,tx-delay-ps = <2030>; |
| mediatek,mac-wol; |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <ð_default_pins>; |
| pinctrl-1 = <ð_sleep_pins>; |
| status = "okay"; |
| |
| mdio { |
| compatible = "snps,dwmac-mdio"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| eth_phy0: eth-phy0@1 { |
| compatible = "ethernet-phy-id001c.c916"; |
| reg = <0x1>; |
| }; |
| }; |
| }; |
| |
| &i2c0 { |
| clock-frequency = <400000>; |
| pinctrl-0 = <&i2c0_pins>; |
| pinctrl-names = "default"; |
| status = "okay"; |
| }; |
| |
| &i2c1 { |
| clock-frequency = <400000>; |
| pinctrl-0 = <&i2c1_pins>; |
| pinctrl-names = "default"; |
| status = "okay"; |
| |
| touchscreen@5d { |
| compatible = "goodix,gt9271"; |
| reg = <0x5d>; |
| interrupts-extended = <&pio 132 IRQ_TYPE_EDGE_RISING>; |
| irq-gpios = <&pio 132 GPIO_ACTIVE_HIGH>; |
| reset-gpios = <&pio 133 GPIO_ACTIVE_HIGH>; |
| AVDD28-supply = <&mt6360_ldo1>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&touch_pins>; |
| }; |
| }; |
| |
| &i2c2 { |
| clock-frequency = <400000>; |
| pinctrl-0 = <&i2c2_pins>; |
| pinctrl-names = "default"; |
| status = "okay"; |
| }; |
| |
| &i2c6 { |
| clock-frequency = <400000>; |
| pinctrl-0 = <&i2c6_pins>; |
| pinctrl-names = "default"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "okay"; |
| |
| mt6360: pmic@34 { |
| compatible = "mediatek,mt6360"; |
| reg = <0x34>; |
| interrupt-parent = <&pio>; |
| interrupts = <128 IRQ_TYPE_EDGE_FALLING>; |
| interrupt-names = "IRQB"; |
| interrupt-controller; |
| #interrupt-cells = <1>; |
| pinctrl-0 = <&mt6360_pins>; |
| |
| charger { |
| compatible = "mediatek,mt6360-chg"; |
| richtek,vinovp-microvolt = <14500000>; |
| |
| otg_vbus_regulator: usb-otg-vbus-regulator { |
| regulator-name = "usb-otg-vbus"; |
| regulator-min-microvolt = <4425000>; |
| regulator-max-microvolt = <5825000>; |
| }; |
| }; |
| |
| regulator { |
| compatible = "mediatek,mt6360-regulator"; |
| LDO_VIN3-supply = <&mt6360_buck2>; |
| |
| mt6360_buck1: buck1 { |
| regulator-name = "emi_vdd2"; |
| regulator-min-microvolt = <300000>; |
| regulator-max-microvolt = <1300000>; |
| regulator-allowed-modes = <MT6360_OPMODE_NORMAL |
| MT6360_OPMODE_LP |
| MT6360_OPMODE_ULP>; |
| regulator-always-on; |
| }; |
| |
| mt6360_buck2: buck2 { |
| regulator-name = "emi_vddq"; |
| regulator-min-microvolt = <300000>; |
| regulator-max-microvolt = <1300000>; |
| regulator-allowed-modes = <MT6360_OPMODE_NORMAL |
| MT6360_OPMODE_LP |
| MT6360_OPMODE_ULP>; |
| regulator-always-on; |
| }; |
| |
| mt6360_ldo1: ldo1 { |
| regulator-name = "tp1_p3v0"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-allowed-modes = <MT6360_OPMODE_NORMAL |
| MT6360_OPMODE_LP>; |
| regulator-always-on; |
| }; |
| |
| mt6360_ldo2: ldo2 { |
| regulator-name = "panel1_p1v8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-allowed-modes = <MT6360_OPMODE_NORMAL |
| MT6360_OPMODE_LP>; |
| }; |
| |
| mt6360_ldo3: ldo3 { |
| regulator-name = "vmc_pmu"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <3600000>; |
| regulator-allowed-modes = <MT6360_OPMODE_NORMAL |
| MT6360_OPMODE_LP>; |
| }; |
| |
| mt6360_ldo5: ldo5 { |
| regulator-name = "vmch_pmu"; |
| regulator-min-microvolt = <2700000>; |
| regulator-max-microvolt = <3600000>; |
| regulator-allowed-modes = <MT6360_OPMODE_NORMAL |
| MT6360_OPMODE_LP>; |
| }; |
| |
| /* This is a measure point, which name is mt6360_ldo1 on schematic */ |
| mt6360_ldo6: ldo6 { |
| regulator-name = "mt6360_ldo1"; |
| regulator-min-microvolt = <500000>; |
| regulator-max-microvolt = <2100000>; |
| regulator-allowed-modes = <MT6360_OPMODE_NORMAL |
| MT6360_OPMODE_LP>; |
| }; |
| |
| mt6360_ldo7: ldo7 { |
| regulator-name = "emi_vmddr_en"; |
| regulator-min-microvolt = <500000>; |
| regulator-max-microvolt = <2100000>; |
| regulator-allowed-modes = <MT6360_OPMODE_NORMAL |
| MT6360_OPMODE_LP>; |
| regulator-always-on; |
| }; |
| }; |
| }; |
| }; |
| |
| &mfg0 { |
| domain-supply = <&mt6315_7_vbuck1>; |
| }; |
| |
| &mmc0 { |
| status = "okay"; |
| pinctrl-names = "default", "state_uhs"; |
| pinctrl-0 = <&mmc0_default_pins>; |
| pinctrl-1 = <&mmc0_uhs_pins>; |
| bus-width = <8>; |
| max-frequency = <200000000>; |
| cap-mmc-highspeed; |
| mmc-hs200-1_8v; |
| mmc-hs400-1_8v; |
| cap-mmc-hw-reset; |
| no-sdio; |
| no-sd; |
| hs400-ds-delay = <0x14c11>; |
| vmmc-supply = <&mt6359_vemc_1_ldo_reg>; |
| vqmmc-supply = <&mt6359_vufs_ldo_reg>; |
| non-removable; |
| }; |
| |
| &mmc1 { |
| pinctrl-names = "default", "state_uhs"; |
| pinctrl-0 = <&mmc1_default_pins>; |
| pinctrl-1 = <&mmc1_uhs_pins>; |
| bus-width = <4>; |
| max-frequency = <200000000>; |
| cap-sd-highspeed; |
| sd-uhs-sdr50; |
| sd-uhs-sdr104; |
| no-mmc; |
| no-sdio; |
| vmmc-supply = <&mt6360_ldo5>; |
| vqmmc-supply = <&mt6360_ldo3>; |
| status = "okay"; |
| non-removable; |
| }; |
| |
| &mt6359_vaud18_ldo_reg { |
| regulator-always-on; |
| }; |
| |
| &mt6359_vbbck_ldo_reg { |
| regulator-always-on; |
| }; |
| |
| /* For USB Hub */ |
| &mt6359_vcamio_ldo_reg { |
| regulator-always-on; |
| }; |
| |
| &mt6359_vcn33_2_bt_ldo_reg { |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| |
| &mt6359_vcore_buck_reg { |
| regulator-always-on; |
| }; |
| |
| &mt6359_vgpu11_buck_reg { |
| regulator-always-on; |
| }; |
| |
| &mt6359_vpu_buck_reg { |
| regulator-always-on; |
| }; |
| |
| &mt6359_vrf12_ldo_reg { |
| regulator-always-on; |
| }; |
| |
| &mt6359codec { |
| mediatek,mic-type-0 = <1>; /* ACC */ |
| mediatek,mic-type-1 = <3>; /* DCC */ |
| mediatek,mic-type-2 = <1>; /* ACC */ |
| }; |
| |
| &pcie0 { |
| pinctrl-names = "default", "idle"; |
| pinctrl-0 = <&pcie0_default_pins>; |
| pinctrl-1 = <&pcie0_idle_pins>; |
| status = "okay"; |
| }; |
| |
| &pcie1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pcie1_default_pins>; |
| status = "disabled"; |
| }; |
| |
| &pciephy { |
| status = "okay"; |
| }; |
| |
| &pio { |
| audio_default_pins: audio-default-pins { |
| pins-cmd-dat { |
| pinmux = <PINMUX_GPIO61__FUNC_DMIC1_CLK>, |
| <PINMUX_GPIO62__FUNC_DMIC1_DAT>, |
| <PINMUX_GPIO65__FUNC_PCM_DO>, |
| <PINMUX_GPIO66__FUNC_PCM_CLK>, |
| <PINMUX_GPIO67__FUNC_PCM_DI>, |
| <PINMUX_GPIO68__FUNC_PCM_SYNC>, |
| <PINMUX_GPIO69__FUNC_AUD_CLK_MOSI>, |
| <PINMUX_GPIO70__FUNC_AUD_SYNC_MOSI>, |
| <PINMUX_GPIO71__FUNC_AUD_DAT_MOSI0>, |
| <PINMUX_GPIO72__FUNC_AUD_DAT_MOSI1>, |
| <PINMUX_GPIO73__FUNC_AUD_DAT_MISO0>, |
| <PINMUX_GPIO74__FUNC_AUD_DAT_MISO1>, |
| <PINMUX_GPIO75__FUNC_AUD_DAT_MISO2>; |
| }; |
| }; |
| |
| disp_pwm1_default_pins: disp-pwm1-default-pins { |
| pins1 { |
| pinmux = <PINMUX_GPIO104__FUNC_DISP_PWM1>; |
| }; |
| }; |
| |
| edp_panel_12v_en_pins: edp-panel-12v-en-pins { |
| pins1 { |
| pinmux = <PINMUX_GPIO96__FUNC_GPIO96>; |
| output-high; |
| }; |
| }; |
| |
| edp_panel_3v3_en_pins: edp-panel-3v3-en-pins { |
| pins1 { |
| pinmux = <PINMUX_GPIO6__FUNC_GPIO6>; |
| output-high; |
| }; |
| }; |
| |
| eth_default_pins: eth-default-pins { |
| pins-cc { |
| pinmux = <PINMUX_GPIO85__FUNC_GBE_TXC>, |
| <PINMUX_GPIO86__FUNC_GBE_RXC>, |
| <PINMUX_GPIO87__FUNC_GBE_RXDV>, |
| <PINMUX_GPIO88__FUNC_GBE_TXEN>; |
| drive-strength = <MTK_DRIVE_8mA>; |
| }; |
| |
| pins-mdio { |
| pinmux = <PINMUX_GPIO89__FUNC_GBE_MDC>, |
| <PINMUX_GPIO90__FUNC_GBE_MDIO>; |
| input-enable; |
| }; |
| |
| pins-power { |
| pinmux = <PINMUX_GPIO91__FUNC_GPIO91>, |
| <PINMUX_GPIO92__FUNC_GPIO92>; |
| output-high; |
| }; |
| |
| pins-rxd { |
| pinmux = <PINMUX_GPIO81__FUNC_GBE_RXD3>, |
| <PINMUX_GPIO82__FUNC_GBE_RXD2>, |
| <PINMUX_GPIO83__FUNC_GBE_RXD1>, |
| <PINMUX_GPIO84__FUNC_GBE_RXD0>; |
| }; |
| |
| pins-txd { |
| pinmux = <PINMUX_GPIO77__FUNC_GBE_TXD3>, |
| <PINMUX_GPIO78__FUNC_GBE_TXD2>, |
| <PINMUX_GPIO79__FUNC_GBE_TXD1>, |
| <PINMUX_GPIO80__FUNC_GBE_TXD0>; |
| drive-strength = <MTK_DRIVE_8mA>; |
| }; |
| }; |
| |
| eth_sleep_pins: eth-sleep-pins { |
| pins-cc { |
| pinmux = <PINMUX_GPIO85__FUNC_GPIO85>, |
| <PINMUX_GPIO86__FUNC_GPIO86>, |
| <PINMUX_GPIO87__FUNC_GPIO87>, |
| <PINMUX_GPIO88__FUNC_GPIO88>; |
| }; |
| |
| pins-mdio { |
| pinmux = <PINMUX_GPIO89__FUNC_GPIO89>, |
| <PINMUX_GPIO90__FUNC_GPIO90>; |
| input-disable; |
| bias-disable; |
| }; |
| |
| pins-rxd { |
| pinmux = <PINMUX_GPIO81__FUNC_GPIO81>, |
| <PINMUX_GPIO82__FUNC_GPIO82>, |
| <PINMUX_GPIO83__FUNC_GPIO83>, |
| <PINMUX_GPIO84__FUNC_GPIO84>; |
| }; |
| |
| pins-txd { |
| pinmux = <PINMUX_GPIO77__FUNC_GPIO77>, |
| <PINMUX_GPIO78__FUNC_GPIO78>, |
| <PINMUX_GPIO79__FUNC_GPIO79>, |
| <PINMUX_GPIO80__FUNC_GPIO80>; |
| }; |
| }; |
| |
| gpio_key_pins: gpio-keys-pins { |
| pins { |
| pinmux = <PINMUX_GPIO106__FUNC_GPIO106>; |
| bias-pull-up; |
| input-enable; |
| }; |
| }; |
| |
| i2c0_pins: i2c0-pins { |
| pins { |
| pinmux = <PINMUX_GPIO8__FUNC_SDA0>, |
| <PINMUX_GPIO9__FUNC_SCL0>; |
| bias-pull-up = <MTK_PULL_SET_RSEL_111>; |
| drive-strength-microamp = <1000>; |
| }; |
| }; |
| |
| i2c1_pins: i2c1-pins { |
| pins { |
| pinmux = <PINMUX_GPIO10__FUNC_SDA1>, |
| <PINMUX_GPIO11__FUNC_SCL1>; |
| bias-pull-up = <MTK_PULL_SET_RSEL_111>; |
| drive-strength-microamp = <1000>; |
| }; |
| }; |
| |
| i2c2_pins: i2c2-pins { |
| pins { |
| pinmux = <PINMUX_GPIO12__FUNC_SDA2>, |
| <PINMUX_GPIO13__FUNC_SCL2>; |
| bias-pull-up = <MTK_PULL_SET_RSEL_111>; |
| drive-strength = <MTK_DRIVE_6mA>; |
| }; |
| }; |
| |
| i2c6_pins: i2c6-pins { |
| pins { |
| pinmux = <PINMUX_GPIO25__FUNC_SDA6>, |
| <PINMUX_GPIO26__FUNC_SCL6>; |
| bias-pull-up; |
| }; |
| }; |
| |
| mmc0_default_pins: mmc0-default-pins { |
| pins-clk { |
| pinmux = <PINMUX_GPIO122__FUNC_MSDC0_CLK>; |
| drive-strength = <MTK_DRIVE_6mA>; |
| bias-pull-down = <MTK_PUPD_SET_R1R0_10>; |
| }; |
| |
| pins-cmd-dat { |
| pinmux = <PINMUX_GPIO126__FUNC_MSDC0_DAT0>, |
| <PINMUX_GPIO125__FUNC_MSDC0_DAT1>, |
| <PINMUX_GPIO124__FUNC_MSDC0_DAT2>, |
| <PINMUX_GPIO123__FUNC_MSDC0_DAT3>, |
| <PINMUX_GPIO119__FUNC_MSDC0_DAT4>, |
| <PINMUX_GPIO118__FUNC_MSDC0_DAT5>, |
| <PINMUX_GPIO117__FUNC_MSDC0_DAT6>, |
| <PINMUX_GPIO116__FUNC_MSDC0_DAT7>, |
| <PINMUX_GPIO121__FUNC_MSDC0_CMD>; |
| input-enable; |
| drive-strength = <MTK_DRIVE_6mA>; |
| bias-pull-up = <MTK_PUPD_SET_R1R0_01>; |
| }; |
| |
| pins-rst { |
| pinmux = <PINMUX_GPIO120__FUNC_MSDC0_RSTB>; |
| drive-strength = <MTK_DRIVE_6mA>; |
| bias-pull-up = <MTK_PUPD_SET_R1R0_01>; |
| }; |
| }; |
| |
| mmc0_uhs_pins: mmc0-uhs-pins { |
| pins-clk { |
| pinmux = <PINMUX_GPIO122__FUNC_MSDC0_CLK>; |
| drive-strength = <MTK_DRIVE_8mA>; |
| bias-pull-down = <MTK_PUPD_SET_R1R0_10>; |
| }; |
| |
| pins-cmd-dat { |
| pinmux = <PINMUX_GPIO126__FUNC_MSDC0_DAT0>, |
| <PINMUX_GPIO125__FUNC_MSDC0_DAT1>, |
| <PINMUX_GPIO124__FUNC_MSDC0_DAT2>, |
| <PINMUX_GPIO123__FUNC_MSDC0_DAT3>, |
| <PINMUX_GPIO119__FUNC_MSDC0_DAT4>, |
| <PINMUX_GPIO118__FUNC_MSDC0_DAT5>, |
| <PINMUX_GPIO117__FUNC_MSDC0_DAT6>, |
| <PINMUX_GPIO116__FUNC_MSDC0_DAT7>, |
| <PINMUX_GPIO121__FUNC_MSDC0_CMD>; |
| input-enable; |
| drive-strength = <MTK_DRIVE_8mA>; |
| bias-pull-up = <MTK_PUPD_SET_R1R0_01>; |
| }; |
| |
| pins-ds { |
| pinmux = <PINMUX_GPIO127__FUNC_MSDC0_DSL>; |
| drive-strength = <MTK_DRIVE_8mA>; |
| bias-pull-down = <MTK_PUPD_SET_R1R0_10>; |
| }; |
| |
| pins-rst { |
| pinmux = <PINMUX_GPIO120__FUNC_MSDC0_RSTB>; |
| drive-strength = <MTK_DRIVE_8mA>; |
| bias-pull-up = <MTK_PUPD_SET_R1R0_01>; |
| }; |
| }; |
| |
| mmc1_default_pins: mmc1-default-pins { |
| pins-clk { |
| pinmux = <PINMUX_GPIO111__FUNC_MSDC1_CLK>; |
| drive-strength = <MTK_DRIVE_8mA>; |
| bias-pull-down = <MTK_PUPD_SET_R1R0_10>; |
| }; |
| |
| pins-cmd-dat { |
| pinmux = <PINMUX_GPIO110__FUNC_MSDC1_CMD>, |
| <PINMUX_GPIO112__FUNC_MSDC1_DAT0>, |
| <PINMUX_GPIO113__FUNC_MSDC1_DAT1>, |
| <PINMUX_GPIO114__FUNC_MSDC1_DAT2>, |
| <PINMUX_GPIO115__FUNC_MSDC1_DAT3>; |
| input-enable; |
| drive-strength = <MTK_DRIVE_8mA>; |
| bias-pull-up = <MTK_PUPD_SET_R1R0_01>; |
| }; |
| }; |
| |
| mmc1_uhs_pins: mmc1-uhs-pins { |
| pins-clk { |
| pinmux = <PINMUX_GPIO111__FUNC_MSDC1_CLK>; |
| drive-strength = <MTK_DRIVE_8mA>; |
| bias-pull-down = <MTK_PUPD_SET_R1R0_10>; |
| }; |
| |
| pins-cmd-dat { |
| pinmux = <PINMUX_GPIO110__FUNC_MSDC1_CMD>, |
| <PINMUX_GPIO112__FUNC_MSDC1_DAT0>, |
| <PINMUX_GPIO113__FUNC_MSDC1_DAT1>, |
| <PINMUX_GPIO114__FUNC_MSDC1_DAT2>, |
| <PINMUX_GPIO115__FUNC_MSDC1_DAT3>; |
| input-enable; |
| drive-strength = <MTK_DRIVE_8mA>; |
| bias-pull-up = <MTK_PUPD_SET_R1R0_01>; |
| }; |
| }; |
| |
| mt6360_pins: mt6360-pins { |
| pins { |
| pinmux = <PINMUX_GPIO17__FUNC_GPIO17>, |
| <PINMUX_GPIO128__FUNC_GPIO128>; |
| input-enable; |
| bias-pull-up; |
| }; |
| }; |
| |
| pcie0_default_pins: pcie0-default-pins { |
| pins { |
| pinmux = <PINMUX_GPIO19__FUNC_WAKEN>, |
| <PINMUX_GPIO20__FUNC_PERSTN>, |
| <PINMUX_GPIO21__FUNC_CLKREQN>; |
| bias-pull-up; |
| }; |
| }; |
| |
| pcie0_idle_pins: pcie0-idle-pins { |
| pins { |
| pinmux = <PINMUX_GPIO20__FUNC_GPIO20>; |
| bias-disable; |
| output-low; |
| }; |
| }; |
| |
| pcie1_default_pins: pcie1-default-pins { |
| pins { |
| pinmux = <PINMUX_GPIO22__FUNC_PERSTN_1>, |
| <PINMUX_GPIO23__FUNC_CLKREQN_1>, |
| <PINMUX_GPIO24__FUNC_WAKEN_1>; |
| bias-pull-up; |
| }; |
| }; |
| |
| pwm0_default_pins: pwm0-default-pins { |
| pins-cmd-dat { |
| pinmux = <PINMUX_GPIO97__FUNC_DISP_PWM0>; |
| }; |
| }; |
| |
| spi1_pins: spi1-pins { |
| pins { |
| pinmux = <PINMUX_GPIO136__FUNC_SPIM1_CSB>, |
| <PINMUX_GPIO137__FUNC_SPIM1_CLK>, |
| <PINMUX_GPIO138__FUNC_SPIM1_MO>, |
| <PINMUX_GPIO139__FUNC_SPIM1_MI>; |
| bias-disable; |
| }; |
| }; |
| |
| spi2_pins: spi-pins { |
| pins { |
| pinmux = <PINMUX_GPIO140__FUNC_SPIM2_CSB>, |
| <PINMUX_GPIO141__FUNC_SPIM2_CLK>, |
| <PINMUX_GPIO142__FUNC_SPIM2_MO>, |
| <PINMUX_GPIO143__FUNC_SPIM2_MI>; |
| bias-disable; |
| }; |
| }; |
| |
| touch_pins: touch-pins { |
| pins-irq { |
| pinmux = <PINMUX_GPIO132__FUNC_GPIO132>; |
| input-enable; |
| bias-disable; |
| }; |
| |
| pins-reset { |
| pinmux = <PINMUX_GPIO133__FUNC_GPIO133>; |
| output-high; |
| }; |
| }; |
| |
| uart0_pins: uart0-pins { |
| pins { |
| pinmux = <PINMUX_GPIO98__FUNC_UTXD0>, |
| <PINMUX_GPIO99__FUNC_URXD0>; |
| }; |
| }; |
| |
| uart1_pins: uart1-pins { |
| pins { |
| pinmux = <PINMUX_GPIO100__FUNC_URTS1>, |
| <PINMUX_GPIO101__FUNC_UCTS1>, |
| <PINMUX_GPIO102__FUNC_UTXD1>, |
| <PINMUX_GPIO103__FUNC_URXD1>; |
| }; |
| }; |
| }; |
| |
| &pmic { |
| interrupts-extended = <&pio 222 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| &scp { |
| memory-region = <&scp_mem>; |
| status = "okay"; |
| }; |
| |
| &spi1 { |
| pinctrl-0 = <&spi1_pins>; |
| pinctrl-names = "default"; |
| mediatek,pad-select = <0>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "okay"; |
| cs-gpios = <&pio 64 GPIO_ACTIVE_LOW>; |
| |
| can0: can@0 { |
| compatible = "microchip,mcp2518fd"; |
| reg = <0>; |
| clocks = <&can_clk>; |
| spi-max-frequency = <20000000>; |
| interrupts-extended = <&pio 16 IRQ_TYPE_LEVEL_LOW>; |
| vdd-supply = <&mt6359_vcn33_2_bt_ldo_reg>; |
| xceiver-supply = <&mt6359_vcn33_2_bt_ldo_reg>; |
| }; |
| }; |
| |
| &spi2 { |
| pinctrl-0 = <&spi2_pins>; |
| pinctrl-names = "default"; |
| mediatek,pad-select = <0>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "okay"; |
| }; |
| |
| &spmi { |
| #address-cells = <2>; |
| #size-cells = <0>; |
| |
| mt6315_6: pmic@6 { |
| compatible = "mediatek,mt6315-regulator"; |
| reg = <0x6 SPMI_USID>; |
| |
| regulators { |
| mt6315_6_vbuck1: vbuck1 { |
| regulator-compatible = "vbuck1"; |
| regulator-name = "Vbcpu"; |
| regulator-min-microvolt = <300000>; |
| regulator-max-microvolt = <1193750>; |
| regulator-enable-ramp-delay = <256>; |
| regulator-allowed-modes = <0 1 2>; |
| regulator-always-on; |
| }; |
| }; |
| }; |
| |
| mt6315_7: pmic@7 { |
| compatible = "mediatek,mt6315-regulator"; |
| reg = <0x7 SPMI_USID>; |
| |
| regulators { |
| mt6315_7_vbuck1: vbuck1 { |
| regulator-compatible = "vbuck1"; |
| regulator-name = "Vgpu"; |
| regulator-min-microvolt = <300000>; |
| regulator-max-microvolt = <1193750>; |
| regulator-enable-ramp-delay = <256>; |
| regulator-allowed-modes = <0 1 2>; |
| }; |
| }; |
| }; |
| }; |
| |
| &u3phy0 { |
| status = "okay"; |
| }; |
| |
| &u3phy1 { |
| status = "okay"; |
| }; |
| |
| &u3phy2 { |
| status = "okay"; |
| }; |
| |
| &u3phy3 { |
| status = "okay"; |
| }; |
| |
| &uart0 { |
| pinctrl-0 = <&uart0_pins>; |
| pinctrl-names = "default"; |
| status = "okay"; |
| }; |
| |
| &uart1 { |
| pinctrl-0 = <&uart1_pins>; |
| pinctrl-names = "default"; |
| status = "okay"; |
| }; |
| |
| &ufsphy { |
| status = "disabled"; |
| }; |
| |
| &ssusb0 { |
| vusb33-supply = <&mt6359_vusb_ldo_reg>; |
| status = "okay"; |
| }; |
| |
| &ssusb2 { |
| vusb33-supply = <&mt6359_vusb_ldo_reg>; |
| status = "okay"; |
| }; |
| |
| &ssusb3 { |
| vusb33-supply = <&mt6359_vusb_ldo_reg>; |
| status = "okay"; |
| }; |
| |
| &xhci0 { |
| status = "okay"; |
| }; |
| |
| &xhci1 { |
| vusb33-supply = <&mt6359_vusb_ldo_reg>; |
| status = "okay"; |
| }; |
| |
| &xhci2 { |
| status = "okay"; |
| }; |
| |
| &xhci3 { |
| status = "okay"; |
| }; |
