| # SPDX-License-Identifier: GPL-2.0 |
| %YAML 1.2 |
| --- |
| $id: http://devicetree.org/schemas/net/snps,dwmac.yaml# |
| $schema: http://devicetree.org/meta-schemas/core.yaml# |
| |
| title: Synopsys DesignWare MAC Device Tree Bindings |
| |
| maintainers: |
| - Alexandre Torgue <alexandre.torgue@st.com> |
| - Giuseppe Cavallaro <peppe.cavallaro@st.com> |
| - Jose Abreu <joabreu@synopsys.com> |
| |
| # Select every compatible, including the deprecated ones. This way, we |
| # will be able to report a warning when we have that compatible, since |
| # we will validate the node thanks to the select, but won't report it |
| # as a valid value in the compatible property description |
| select: |
| properties: |
| compatible: |
| contains: |
| enum: |
| - snps,dwmac |
| - snps,dwmac-3.50a |
| - snps,dwmac-3.610 |
| - snps,dwmac-3.70a |
| - snps,dwmac-3.710 |
| - snps,dwmac-4.00 |
| - snps,dwmac-4.10a |
| - snps,dwmac-4.20a |
| - snps,dwxgmac |
| - snps,dwxgmac-2.10 |
| |
| # Deprecated |
| - st,spear600-gmac |
| |
| required: |
| - compatible |
| |
| properties: |
| |
| # We need to include all the compatibles from schemas that will |
| # include that schemas, otherwise compatible won't validate for |
| # those. |
| compatible: |
| contains: |
| enum: |
| - allwinner,sun7i-a20-gmac |
| - allwinner,sun8i-a83t-emac |
| - allwinner,sun8i-h3-emac |
| - allwinner,sun8i-r40-emac |
| - allwinner,sun8i-v3s-emac |
| - allwinner,sun50i-a64-emac |
| - amlogic,meson6-dwmac |
| - amlogic,meson8b-dwmac |
| - amlogic,meson8m2-dwmac |
| - amlogic,meson-gxbb-dwmac |
| - amlogic,meson-axg-dwmac |
| - snps,dwmac |
| - snps,dwmac-3.50a |
| - snps,dwmac-3.610 |
| - snps,dwmac-3.70a |
| - snps,dwmac-3.710 |
| - snps,dwmac-4.00 |
| - snps,dwmac-4.10a |
| - snps,dwmac-4.20a |
| - snps,dwxgmac |
| - snps,dwxgmac-2.10 |
| |
| reg: |
| minItems: 1 |
| maxItems: 2 |
| |
| interrupts: |
| minItems: 1 |
| maxItems: 3 |
| items: |
| - description: Combined signal for various interrupt events |
| - description: The interrupt to manage the remote wake-up packet detection |
| - description: The interrupt that occurs when Rx exits the LPI state |
| |
| interrupt-names: |
| minItems: 1 |
| maxItems: 3 |
| items: |
| - const: macirq |
| - const: eth_wake_irq |
| - const: eth_lpi |
| |
| clocks: |
| minItems: 1 |
| maxItems: 5 |
| additionalItems: true |
| items: |
| - description: GMAC main clock |
| - description: Peripheral registers interface clock |
| - description: |
| PTP reference clock. This clock is used for programming the |
| Timestamp Addend Register. If not passed then the system |
| clock will be used and this is fine on some platforms. |
| |
| clock-names: |
| minItems: 1 |
| maxItems: 5 |
| additionalItems: true |
| contains: |
| enum: |
| - stmmaceth |
| - pclk |
| - ptp_ref |
| |
| resets: |
| maxItems: 1 |
| description: |
| MAC Reset signal. |
| |
| reset-names: |
| const: stmmaceth |
| |
| mac-mode: |
| $ref: ethernet-controller.yaml#/properties/phy-connection-type |
| description: |
| The property is identical to 'phy-mode', and assumes that there is mode |
| converter in-between the MAC & PHY (e.g. GMII-to-RGMII). This converter |
| can be passive (no SW requirement), and requires that the MAC operate |
| in a different mode than the PHY in order to function. |
| |
| snps,axi-config: |
| $ref: /schemas/types.yaml#definitions/phandle |
| description: |
| AXI BUS Mode parameters. Phandle to a node that can contain the |
| following properties |
| * snps,lpi_en, enable Low Power Interface |
| * snps,xit_frm, unlock on WoL |
| * snps,wr_osr_lmt, max write outstanding req. limit |
| * snps,rd_osr_lmt, max read outstanding req. limit |
| * snps,kbbe, do not cross 1KiB boundary. |
| * snps,blen, this is a vector of supported burst length. |
| * snps,fb, fixed-burst |
| * snps,mb, mixed-burst |
| * snps,rb, rebuild INCRx Burst |
| |
| snps,mtl-rx-config: |
| $ref: /schemas/types.yaml#definitions/phandle |
| description: |
| Multiple RX Queues parameters. Phandle to a node that can |
| contain the following properties |
| * snps,rx-queues-to-use, number of RX queues to be used in the |
| driver |
| * Choose one of these RX scheduling algorithms |
| * snps,rx-sched-sp, Strict priority |
| * snps,rx-sched-wsp, Weighted Strict priority |
| * For each RX queue |
| * Choose one of these modes |
| * snps,dcb-algorithm, Queue to be enabled as DCB |
| * snps,avb-algorithm, Queue to be enabled as AVB |
| * snps,map-to-dma-channel, Channel to map |
| * Specifiy specific packet routing |
| * snps,route-avcp, AV Untagged Control packets |
| * snps,route-ptp, PTP Packets |
| * snps,route-dcbcp, DCB Control Packets |
| * snps,route-up, Untagged Packets |
| * snps,route-multi-broad, Multicast & Broadcast Packets |
| * snps,priority, RX queue priority (Range 0x0 to 0xF) |
| |
| snps,mtl-tx-config: |
| $ref: /schemas/types.yaml#definitions/phandle |
| description: |
| Multiple TX Queues parameters. Phandle to a node that can |
| contain the following properties |
| * snps,tx-queues-to-use, number of TX queues to be used in the |
| driver |
| * Choose one of these TX scheduling algorithms |
| * snps,tx-sched-wrr, Weighted Round Robin |
| * snps,tx-sched-wfq, Weighted Fair Queuing |
| * snps,tx-sched-dwrr, Deficit Weighted Round Robin |
| * snps,tx-sched-sp, Strict priority |
| * For each TX queue |
| * snps,weight, TX queue weight (if using a DCB weight |
| algorithm) |
| * Choose one of these modes |
| * snps,dcb-algorithm, TX queue will be working in DCB |
| * snps,avb-algorithm, TX queue will be working in AVB |
| [Attention] Queue 0 is reserved for legacy traffic |
| and so no AVB is available in this queue. |
| * Configure Credit Base Shaper (if AVB Mode selected) |
| * snps,send_slope, enable Low Power Interface |
| * snps,idle_slope, unlock on WoL |
| * snps,high_credit, max write outstanding req. limit |
| * snps,low_credit, max read outstanding req. limit |
| * snps,priority, TX queue priority (Range 0x0 to 0xF) |
| |
| snps,reset-gpio: |
| deprecated: true |
| maxItems: 1 |
| description: |
| PHY Reset GPIO |
| |
| snps,reset-active-low: |
| deprecated: true |
| $ref: /schemas/types.yaml#definitions/flag |
| description: |
| Indicates that the PHY Reset is active low |
| |
| snps,reset-delays-us: |
| deprecated: true |
| description: |
| Triplet of delays. The 1st cell is reset pre-delay in micro |
| seconds. The 2nd cell is reset pulse in micro seconds. The 3rd |
| cell is reset post-delay in micro seconds. |
| $ref: /schemas/types.yaml#definitions/uint32-array |
| minItems: 3 |
| maxItems: 3 |
| |
| snps,aal: |
| $ref: /schemas/types.yaml#definitions/flag |
| description: |
| Use Address-Aligned Beats |
| |
| snps,fixed-burst: |
| $ref: /schemas/types.yaml#definitions/flag |
| description: |
| Program the DMA to use the fixed burst mode |
| |
| snps,mixed-burst: |
| $ref: /schemas/types.yaml#definitions/flag |
| description: |
| Program the DMA to use the mixed burst mode |
| |
| snps,force_thresh_dma_mode: |
| $ref: /schemas/types.yaml#definitions/flag |
| description: |
| Force DMA to use the threshold mode for both tx and rx |
| |
| snps,force_sf_dma_mode: |
| $ref: /schemas/types.yaml#definitions/flag |
| description: |
| Force DMA to use the Store and Forward mode for both tx and |
| rx. This flag is ignored if force_thresh_dma_mode is set. |
| |
| snps,en-tx-lpi-clockgating: |
| $ref: /schemas/types.yaml#definitions/flag |
| description: |
| Enable gating of the MAC TX clock during TX low-power mode |
| |
| snps,multicast-filter-bins: |
| $ref: /schemas/types.yaml#definitions/uint32 |
| description: |
| Number of multicast filter hash bins supported by this device |
| instance |
| |
| snps,perfect-filter-entries: |
| $ref: /schemas/types.yaml#definitions/uint32 |
| description: |
| Number of perfect filter entries supported by this device |
| instance |
| |
| snps,ps-speed: |
| $ref: /schemas/types.yaml#definitions/uint32 |
| description: |
| Port selection speed that can be passed to the core when PCS |
| is supported. For example, this is used in case of SGMII and |
| MAC2MAC connection. |
| |
| mdio: |
| type: object |
| description: |
| Creates and registers an MDIO bus. |
| |
| properties: |
| compatible: |
| const: snps,dwmac-mdio |
| |
| required: |
| - compatible |
| |
| required: |
| - compatible |
| - reg |
| - interrupts |
| - interrupt-names |
| - phy-mode |
| |
| dependencies: |
| snps,reset-active-low: ["snps,reset-gpio"] |
| snps,reset-delay-us: ["snps,reset-gpio"] |
| |
| allOf: |
| - $ref: "ethernet-controller.yaml#" |
| - if: |
| properties: |
| compatible: |
| contains: |
| enum: |
| - allwinner,sun7i-a20-gmac |
| - allwinner,sun8i-a83t-emac |
| - allwinner,sun8i-h3-emac |
| - allwinner,sun8i-r40-emac |
| - allwinner,sun8i-v3s-emac |
| - allwinner,sun50i-a64-emac |
| - snps,dwxgmac |
| - snps,dwxgmac-2.10 |
| - st,spear600-gmac |
| |
| then: |
| properties: |
| snps,pbl: |
| description: |
| Programmable Burst Length (tx and rx) |
| $ref: /schemas/types.yaml#definitions/uint32 |
| enum: [2, 4, 8] |
| |
| snps,txpbl: |
| description: |
| Tx Programmable Burst Length. If set, DMA tx will use this |
| value rather than snps,pbl. |
| $ref: /schemas/types.yaml#definitions/uint32 |
| enum: [2, 4, 8] |
| |
| snps,rxpbl: |
| description: |
| Rx Programmable Burst Length. If set, DMA rx will use this |
| value rather than snps,pbl. |
| $ref: /schemas/types.yaml#definitions/uint32 |
| enum: [2, 4, 8] |
| |
| snps,no-pbl-x8: |
| $ref: /schemas/types.yaml#definitions/flag |
| description: |
| Don\'t multiply the pbl/txpbl/rxpbl values by 8. For core |
| rev < 3.50, don\'t multiply the values by 4. |
| |
| - if: |
| properties: |
| compatible: |
| contains: |
| enum: |
| - allwinner,sun7i-a20-gmac |
| - allwinner,sun8i-a83t-emac |
| - allwinner,sun8i-h3-emac |
| - allwinner,sun8i-r40-emac |
| - allwinner,sun8i-v3s-emac |
| - allwinner,sun50i-a64-emac |
| - snps,dwmac-4.00 |
| - snps,dwmac-4.10a |
| - snps,dwmac-4.20a |
| - snps,dwxgmac |
| - snps,dwxgmac-2.10 |
| - st,spear600-gmac |
| |
| then: |
| properties: |
| snps,tso: |
| $ref: /schemas/types.yaml#definitions/flag |
| description: |
| Enables the TSO feature otherwise it will be managed by |
| MAC HW capability register. |
| |
| additionalProperties: true |
| |
| examples: |
| - | |
| stmmac_axi_setup: stmmac-axi-config { |
| snps,wr_osr_lmt = <0xf>; |
| snps,rd_osr_lmt = <0xf>; |
| snps,blen = <256 128 64 32 0 0 0>; |
| }; |
| |
| mtl_rx_setup: rx-queues-config { |
| snps,rx-queues-to-use = <1>; |
| snps,rx-sched-sp; |
| queue0 { |
| snps,dcb-algorithm; |
| snps,map-to-dma-channel = <0x0>; |
| snps,priority = <0x0>; |
| }; |
| }; |
| |
| mtl_tx_setup: tx-queues-config { |
| snps,tx-queues-to-use = <2>; |
| snps,tx-sched-wrr; |
| queue0 { |
| snps,weight = <0x10>; |
| snps,dcb-algorithm; |
| snps,priority = <0x0>; |
| }; |
| |
| queue1 { |
| snps,avb-algorithm; |
| snps,send_slope = <0x1000>; |
| snps,idle_slope = <0x1000>; |
| snps,high_credit = <0x3E800>; |
| snps,low_credit = <0xFFC18000>; |
| snps,priority = <0x1>; |
| }; |
| }; |
| |
| gmac0: ethernet@e0800000 { |
| compatible = "snps,dwxgmac-2.10", "snps,dwxgmac"; |
| reg = <0xe0800000 0x8000>; |
| interrupt-parent = <&vic1>; |
| interrupts = <24 23 22>; |
| interrupt-names = "macirq", "eth_wake_irq", "eth_lpi"; |
| mac-address = [000000000000]; /* Filled in by U-Boot */ |
| max-frame-size = <3800>; |
| phy-mode = "gmii"; |
| snps,multicast-filter-bins = <256>; |
| snps,perfect-filter-entries = <128>; |
| rx-fifo-depth = <16384>; |
| tx-fifo-depth = <16384>; |
| clocks = <&clock>; |
| clock-names = "stmmaceth"; |
| snps,axi-config = <&stmmac_axi_setup>; |
| snps,mtl-rx-config = <&mtl_rx_setup>; |
| snps,mtl-tx-config = <&mtl_tx_setup>; |
| mdio0 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "snps,dwmac-mdio"; |
| phy1: ethernet-phy@0 { |
| reg = <0>; |
| }; |
| }; |
| }; |
| |
| # FIXME: We should set it, but it would report all the generic |
| # properties as additional properties. |
| # additionalProperties: false |
| |
| ... |
