| // SPDX-License-Identifier: GPL-2.0 |
| // |
| // Copyright (C) 2015 Freescale Semiconductor, Inc. |
| |
| / { |
| chosen { |
| stdout-path = &uart1; |
| }; |
| |
| memory@80000000 { |
| device_type = "memory"; |
| reg = <0x80000000 0x20000000>; |
| }; |
| |
| backlight_display: backlight-display { |
| compatible = "pwm-backlight"; |
| pwms = <&pwm1 0 5000000>; |
| brightness-levels = <0 4 8 16 32 64 128 255>; |
| default-brightness-level = <6>; |
| status = "okay"; |
| }; |
| |
| |
| reg_sd1_vmmc: regulator-sd1-vmmc { |
| compatible = "regulator-fixed"; |
| regulator-name = "VSD_3V3"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| gpio = <&gpio1 9 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| |
| reg_can_3v3: regulator-can-3v3 { |
| compatible = "regulator-fixed"; |
| regulator-name = "can-3v3"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| gpios = <&gpio_spi 3 GPIO_ACTIVE_LOW>; |
| }; |
| |
| sound { |
| compatible = "simple-audio-card"; |
| simple-audio-card,name = "mx6ul-wm8960"; |
| simple-audio-card,format = "i2s"; |
| simple-audio-card,bitclock-master = <&dailink_master>; |
| simple-audio-card,frame-master = <&dailink_master>; |
| simple-audio-card,widgets = |
| "Microphone", "Mic Jack", |
| "Line", "Line In", |
| "Line", "Line Out", |
| "Speaker", "Speaker", |
| "Headphone", "Headphone Jack"; |
| simple-audio-card,routing = |
| "Headphone Jack", "HP_L", |
| "Headphone Jack", "HP_R", |
| "Speaker", "SPK_LP", |
| "Speaker", "SPK_LN", |
| "Speaker", "SPK_RP", |
| "Speaker", "SPK_RN", |
| "LINPUT1", "Mic Jack", |
| "LINPUT3", "Mic Jack", |
| "RINPUT1", "Mic Jack", |
| "RINPUT2", "Mic Jack"; |
| |
| simple-audio-card,cpu { |
| sound-dai = <&sai2>; |
| }; |
| |
| dailink_master: simple-audio-card,codec { |
| sound-dai = <&codec>; |
| clocks = <&clks IMX6UL_CLK_SAI2>; |
| }; |
| }; |
| |
| spi4 { |
| compatible = "spi-gpio"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_spi4>; |
| status = "okay"; |
| gpio-sck = <&gpio5 11 0>; |
| gpio-mosi = <&gpio5 10 0>; |
| cs-gpios = <&gpio5 7 0>; |
| num-chipselects = <1>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| gpio_spi: gpio@0 { |
| compatible = "fairchild,74hc595"; |
| gpio-controller; |
| #gpio-cells = <2>; |
| reg = <0>; |
| registers-number = <1>; |
| spi-max-frequency = <100000>; |
| }; |
| }; |
| |
| panel { |
| compatible = "innolux,at043tn24"; |
| backlight = <&backlight_display>; |
| |
| port { |
| panel_in: endpoint { |
| remote-endpoint = <&display_out>; |
| }; |
| }; |
| }; |
| }; |
| |
| &clks { |
| assigned-clocks = <&clks IMX6UL_CLK_PLL4_AUDIO_DIV>; |
| assigned-clock-rates = <786432000>; |
| }; |
| |
| &i2c2 { |
| clock_frequency = <100000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c2>; |
| status = "okay"; |
| |
| codec: wm8960@1a { |
| #sound-dai-cells = <0>; |
| compatible = "wlf,wm8960"; |
| reg = <0x1a>; |
| wlf,shared-lrclk; |
| }; |
| }; |
| |
| &fec1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_enet1>; |
| phy-mode = "rmii"; |
| phy-handle = <ðphy0>; |
| status = "okay"; |
| }; |
| |
| &fec2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_enet2>; |
| phy-mode = "rmii"; |
| phy-handle = <ðphy1>; |
| status = "okay"; |
| |
| mdio { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| ethphy0: ethernet-phy@2 { |
| reg = <2>; |
| micrel,led-mode = <1>; |
| clocks = <&clks IMX6UL_CLK_ENET_REF>; |
| clock-names = "rmii-ref"; |
| }; |
| |
| ethphy1: ethernet-phy@1 { |
| reg = <1>; |
| micrel,led-mode = <1>; |
| clocks = <&clks IMX6UL_CLK_ENET2_REF>; |
| clock-names = "rmii-ref"; |
| }; |
| }; |
| }; |
| |
| &can1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_flexcan1>; |
| xceiver-supply = <®_can_3v3>; |
| status = "okay"; |
| }; |
| |
| &can2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_flexcan2>; |
| xceiver-supply = <®_can_3v3>; |
| status = "okay"; |
| }; |
| |
| &i2c1 { |
| clock-frequency = <100000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c1>; |
| status = "okay"; |
| |
| mag3110@e { |
| compatible = "fsl,mag3110"; |
| reg = <0x0e>; |
| }; |
| }; |
| |
| &lcdif { |
| assigned-clocks = <&clks IMX6UL_CLK_LCDIF_PRE_SEL>; |
| assigned-clock-parents = <&clks IMX6UL_CLK_PLL5_VIDEO_DIV>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_lcdif_dat |
| &pinctrl_lcdif_ctrl>; |
| status = "okay"; |
| |
| port { |
| display_out: endpoint { |
| remote-endpoint = <&panel_in>; |
| }; |
| }; |
| }; |
| |
| &pwm1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_pwm1>; |
| status = "okay"; |
| }; |
| |
| &qspi { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_qspi>; |
| status = "okay"; |
| |
| flash0: n25q256a@0 { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| compatible = "micron,n25q256a"; |
| spi-max-frequency = <29000000>; |
| spi-rx-bus-width = <4>; |
| spi-tx-bus-width = <4>; |
| reg = <0>; |
| }; |
| }; |
| |
| &sai2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_sai2>; |
| assigned-clocks = <&clks IMX6UL_CLK_SAI2_SEL>, |
| <&clks IMX6UL_CLK_SAI2>; |
| assigned-clock-parents = <&clks IMX6UL_CLK_PLL4_AUDIO_DIV>; |
| assigned-clock-rates = <0>, <12288000>; |
| fsl,sai-mclk-direction-output; |
| status = "okay"; |
| }; |
| |
| &snvs_poweroff { |
| status = "okay"; |
| }; |
| |
| &tsc { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_tsc>; |
| xnur-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>; |
| measure-delay-time = <0xffff>; |
| pre-charge-time = <0xfff>; |
| status = "okay"; |
| }; |
| |
| &uart1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart1>; |
| status = "okay"; |
| }; |
| |
| &uart2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart2>; |
| uart-has-rtscts; |
| status = "okay"; |
| }; |
| |
| &usbotg1 { |
| dr_mode = "otg"; |
| status = "okay"; |
| }; |
| |
| &usbotg2 { |
| dr_mode = "host"; |
| disable-over-current; |
| status = "okay"; |
| }; |
| |
| &usbphy1 { |
| fsl,tx-d-cal = <106>; |
| }; |
| |
| &usbphy2 { |
| fsl,tx-d-cal = <106>; |
| }; |
| |
| &usdhc1 { |
| pinctrl-names = "default", "state_100mhz", "state_200mhz"; |
| pinctrl-0 = <&pinctrl_usdhc1>; |
| pinctrl-1 = <&pinctrl_usdhc1_100mhz>; |
| pinctrl-2 = <&pinctrl_usdhc1_200mhz>; |
| cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>; |
| keep-power-in-suspend; |
| wakeup-source; |
| vmmc-supply = <®_sd1_vmmc>; |
| status = "okay"; |
| }; |
| |
| &usdhc2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usdhc2>; |
| no-1-8-v; |
| keep-power-in-suspend; |
| wakeup-source; |
| status = "okay"; |
| }; |
| |
| &wdog1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_wdog>; |
| fsl,ext-reset-output; |
| }; |
| |
| &iomuxc { |
| pinctrl-names = "default"; |
| |
| pinctrl_csi1: csi1grp { |
| fsl,pins = < |
| MX6UL_PAD_CSI_MCLK__CSI_MCLK 0x1b088 |
| MX6UL_PAD_CSI_PIXCLK__CSI_PIXCLK 0x1b088 |
| MX6UL_PAD_CSI_VSYNC__CSI_VSYNC 0x1b088 |
| MX6UL_PAD_CSI_HSYNC__CSI_HSYNC 0x1b088 |
| MX6UL_PAD_CSI_DATA00__CSI_DATA02 0x1b088 |
| MX6UL_PAD_CSI_DATA01__CSI_DATA03 0x1b088 |
| MX6UL_PAD_CSI_DATA02__CSI_DATA04 0x1b088 |
| MX6UL_PAD_CSI_DATA03__CSI_DATA05 0x1b088 |
| MX6UL_PAD_CSI_DATA04__CSI_DATA06 0x1b088 |
| MX6UL_PAD_CSI_DATA05__CSI_DATA07 0x1b088 |
| MX6UL_PAD_CSI_DATA06__CSI_DATA08 0x1b088 |
| MX6UL_PAD_CSI_DATA07__CSI_DATA09 0x1b088 |
| >; |
| }; |
| |
| pinctrl_enet1: enet1grp { |
| fsl,pins = < |
| MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN 0x1b0b0 |
| MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER 0x1b0b0 |
| MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x1b0b0 |
| MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x1b0b0 |
| MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN 0x1b0b0 |
| MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x1b0b0 |
| MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x1b0b0 |
| MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x4001b031 |
| >; |
| }; |
| |
| pinctrl_enet2: enet2grp { |
| fsl,pins = < |
| MX6UL_PAD_GPIO1_IO07__ENET2_MDC 0x1b0b0 |
| MX6UL_PAD_GPIO1_IO06__ENET2_MDIO 0x1b0b0 |
| MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN 0x1b0b0 |
| MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER 0x1b0b0 |
| MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00 0x1b0b0 |
| MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01 0x1b0b0 |
| MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN 0x1b0b0 |
| MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00 0x1b0b0 |
| MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01 0x1b0b0 |
| MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 0x4001b031 |
| >; |
| }; |
| |
| pinctrl_flexcan1: flexcan1grp{ |
| fsl,pins = < |
| MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX 0x1b020 |
| MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX 0x1b020 |
| >; |
| }; |
| |
| pinctrl_flexcan2: flexcan2grp{ |
| fsl,pins = < |
| MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX 0x1b020 |
| MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX 0x1b020 |
| >; |
| }; |
| |
| pinctrl_i2c1: i2c1grp { |
| fsl,pins = < |
| MX6UL_PAD_UART4_TX_DATA__I2C1_SCL 0x4001b8b0 |
| MX6UL_PAD_UART4_RX_DATA__I2C1_SDA 0x4001b8b0 |
| >; |
| }; |
| |
| pinctrl_i2c2: i2c2grp { |
| fsl,pins = < |
| MX6UL_PAD_UART5_TX_DATA__I2C2_SCL 0x4001b8b0 |
| MX6UL_PAD_UART5_RX_DATA__I2C2_SDA 0x4001b8b0 |
| >; |
| }; |
| |
| pinctrl_lcdif_dat: lcdifdatgrp { |
| fsl,pins = < |
| MX6UL_PAD_LCD_DATA00__LCDIF_DATA00 0x79 |
| MX6UL_PAD_LCD_DATA01__LCDIF_DATA01 0x79 |
| MX6UL_PAD_LCD_DATA02__LCDIF_DATA02 0x79 |
| MX6UL_PAD_LCD_DATA03__LCDIF_DATA03 0x79 |
| MX6UL_PAD_LCD_DATA04__LCDIF_DATA04 0x79 |
| MX6UL_PAD_LCD_DATA05__LCDIF_DATA05 0x79 |
| MX6UL_PAD_LCD_DATA06__LCDIF_DATA06 0x79 |
| MX6UL_PAD_LCD_DATA07__LCDIF_DATA07 0x79 |
| MX6UL_PAD_LCD_DATA08__LCDIF_DATA08 0x79 |
| MX6UL_PAD_LCD_DATA09__LCDIF_DATA09 0x79 |
| MX6UL_PAD_LCD_DATA10__LCDIF_DATA10 0x79 |
| MX6UL_PAD_LCD_DATA11__LCDIF_DATA11 0x79 |
| MX6UL_PAD_LCD_DATA12__LCDIF_DATA12 0x79 |
| MX6UL_PAD_LCD_DATA13__LCDIF_DATA13 0x79 |
| MX6UL_PAD_LCD_DATA14__LCDIF_DATA14 0x79 |
| MX6UL_PAD_LCD_DATA15__LCDIF_DATA15 0x79 |
| MX6UL_PAD_LCD_DATA16__LCDIF_DATA16 0x79 |
| MX6UL_PAD_LCD_DATA17__LCDIF_DATA17 0x79 |
| MX6UL_PAD_LCD_DATA18__LCDIF_DATA18 0x79 |
| MX6UL_PAD_LCD_DATA19__LCDIF_DATA19 0x79 |
| MX6UL_PAD_LCD_DATA20__LCDIF_DATA20 0x79 |
| MX6UL_PAD_LCD_DATA21__LCDIF_DATA21 0x79 |
| MX6UL_PAD_LCD_DATA22__LCDIF_DATA22 0x79 |
| MX6UL_PAD_LCD_DATA23__LCDIF_DATA23 0x79 |
| >; |
| }; |
| |
| pinctrl_lcdif_ctrl: lcdifctrlgrp { |
| fsl,pins = < |
| MX6UL_PAD_LCD_CLK__LCDIF_CLK 0x79 |
| MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE 0x79 |
| MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC 0x79 |
| MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC 0x79 |
| /* used for lcd reset */ |
| MX6UL_PAD_SNVS_TAMPER9__GPIO5_IO09 0x79 |
| >; |
| }; |
| |
| pinctrl_qspi: qspigrp { |
| fsl,pins = < |
| MX6UL_PAD_NAND_WP_B__QSPI_A_SCLK 0x70a1 |
| MX6UL_PAD_NAND_READY_B__QSPI_A_DATA00 0x70a1 |
| MX6UL_PAD_NAND_CE0_B__QSPI_A_DATA01 0x70a1 |
| MX6UL_PAD_NAND_CE1_B__QSPI_A_DATA02 0x70a1 |
| MX6UL_PAD_NAND_CLE__QSPI_A_DATA03 0x70a1 |
| MX6UL_PAD_NAND_DQS__QSPI_A_SS0_B 0x70a1 |
| >; |
| }; |
| |
| pinctrl_sai2: sai2grp { |
| fsl,pins = < |
| MX6UL_PAD_JTAG_TDI__SAI2_TX_BCLK 0x17088 |
| MX6UL_PAD_JTAG_TDO__SAI2_TX_SYNC 0x17088 |
| MX6UL_PAD_JTAG_TRST_B__SAI2_TX_DATA 0x11088 |
| MX6UL_PAD_JTAG_TCK__SAI2_RX_DATA 0x11088 |
| MX6UL_PAD_JTAG_TMS__SAI2_MCLK 0x17088 |
| MX6UL_PAD_SNVS_TAMPER4__GPIO5_IO04 0x17059 |
| >; |
| }; |
| |
| pinctrl_pwm1: pwm1grp { |
| fsl,pins = < |
| MX6UL_PAD_GPIO1_IO08__PWM1_OUT 0x110b0 |
| >; |
| }; |
| |
| pinctrl_sim2: sim2grp { |
| fsl,pins = < |
| MX6UL_PAD_CSI_DATA03__SIM2_PORT1_PD 0xb808 |
| MX6UL_PAD_CSI_DATA04__SIM2_PORT1_CLK 0x31 |
| MX6UL_PAD_CSI_DATA05__SIM2_PORT1_RST_B 0xb808 |
| MX6UL_PAD_CSI_DATA06__SIM2_PORT1_SVEN 0xb808 |
| MX6UL_PAD_CSI_DATA07__SIM2_PORT1_TRXD 0xb809 |
| MX6UL_PAD_CSI_DATA02__GPIO4_IO23 0x3008 |
| >; |
| }; |
| |
| pinctrl_spi4: spi4grp { |
| fsl,pins = < |
| MX6UL_PAD_BOOT_MODE0__GPIO5_IO10 0x70a1 |
| MX6UL_PAD_BOOT_MODE1__GPIO5_IO11 0x70a1 |
| MX6UL_PAD_SNVS_TAMPER7__GPIO5_IO07 0x70a1 |
| MX6UL_PAD_SNVS_TAMPER8__GPIO5_IO08 0x80000000 |
| >; |
| }; |
| |
| pinctrl_tsc: tscgrp { |
| fsl,pins = < |
| MX6UL_PAD_GPIO1_IO01__GPIO1_IO01 0xb0 |
| MX6UL_PAD_GPIO1_IO02__GPIO1_IO02 0xb0 |
| MX6UL_PAD_GPIO1_IO03__GPIO1_IO03 0xb0 |
| MX6UL_PAD_GPIO1_IO04__GPIO1_IO04 0xb0 |
| >; |
| }; |
| |
| pinctrl_uart1: uart1grp { |
| fsl,pins = < |
| MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b1 |
| MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x1b0b1 |
| >; |
| }; |
| |
| pinctrl_uart2: uart2grp { |
| fsl,pins = < |
| MX6UL_PAD_UART2_TX_DATA__UART2_DCE_TX 0x1b0b1 |
| MX6UL_PAD_UART2_RX_DATA__UART2_DCE_RX 0x1b0b1 |
| MX6UL_PAD_UART3_RX_DATA__UART2_DCE_RTS 0x1b0b1 |
| MX6UL_PAD_UART3_TX_DATA__UART2_DCE_CTS 0x1b0b1 |
| >; |
| }; |
| |
| pinctrl_usdhc1: usdhc1grp { |
| fsl,pins = < |
| MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x17059 |
| MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x10059 |
| MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x17059 |
| MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x17059 |
| MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x17059 |
| MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x17059 |
| MX6UL_PAD_UART1_RTS_B__GPIO1_IO19 0x17059 /* SD1 CD */ |
| MX6UL_PAD_GPIO1_IO05__USDHC1_VSELECT 0x17059 /* SD1 VSELECT */ |
| MX6UL_PAD_GPIO1_IO09__GPIO1_IO09 0x17059 /* SD1 RESET */ |
| >; |
| }; |
| |
| pinctrl_usdhc1_100mhz: usdhc1grp100mhz { |
| fsl,pins = < |
| MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x170b9 |
| MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x100b9 |
| MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x170b9 |
| MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x170b9 |
| MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x170b9 |
| MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x170b9 |
| |
| >; |
| }; |
| |
| pinctrl_usdhc1_200mhz: usdhc1grp200mhz { |
| fsl,pins = < |
| MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x170f9 |
| MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x100f9 |
| MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x170f9 |
| MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x170f9 |
| MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x170f9 |
| MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x170f9 |
| >; |
| }; |
| |
| pinctrl_usdhc2: usdhc2grp { |
| fsl,pins = < |
| MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x17059 |
| MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x17059 |
| MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x17059 |
| MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x17059 |
| MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x17059 |
| MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x17059 |
| >; |
| }; |
| |
| pinctrl_wdog: wdoggrp { |
| fsl,pins = < |
| MX6UL_PAD_LCD_RESET__WDOG1_WDOG_ANY 0x30b0 |
| >; |
| }; |
| }; |
