| // SPDX-License-Identifier: GPL-2.0+ |
| /** |
| * Driver for Analog Devices Industrial Ethernet PHYs |
| * |
| * Copyright 2019 Analog Devices Inc. |
| */ |
| #include <linux/kernel.h> |
| #include <linux/bitfield.h> |
| #include <linux/delay.h> |
| #include <linux/errno.h> |
| #include <linux/init.h> |
| #include <linux/module.h> |
| #include <linux/mii.h> |
| #include <linux/phy.h> |
| #include <linux/property.h> |
| |
| #define PHY_ID_ADIN1200 0x0283bc20 |
| #define PHY_ID_ADIN1300 0x0283bc30 |
| |
| #define ADIN1300_MII_EXT_REG_PTR 0x0010 |
| #define ADIN1300_MII_EXT_REG_DATA 0x0011 |
| |
| #define ADIN1300_PHY_CTRL1 0x0012 |
| #define ADIN1300_AUTO_MDI_EN BIT(10) |
| #define ADIN1300_MAN_MDIX_EN BIT(9) |
| |
| #define ADIN1300_RX_ERR_CNT 0x0014 |
| |
| #define ADIN1300_PHY_CTRL_STATUS2 0x0015 |
| #define ADIN1300_NRG_PD_EN BIT(3) |
| #define ADIN1300_NRG_PD_TX_EN BIT(2) |
| #define ADIN1300_NRG_PD_STATUS BIT(1) |
| |
| #define ADIN1300_PHY_CTRL2 0x0016 |
| #define ADIN1300_DOWNSPEED_AN_100_EN BIT(11) |
| #define ADIN1300_DOWNSPEED_AN_10_EN BIT(10) |
| #define ADIN1300_GROUP_MDIO_EN BIT(6) |
| #define ADIN1300_DOWNSPEEDS_EN \ |
| (ADIN1300_DOWNSPEED_AN_100_EN | ADIN1300_DOWNSPEED_AN_10_EN) |
| |
| #define ADIN1300_PHY_CTRL3 0x0017 |
| #define ADIN1300_LINKING_EN BIT(13) |
| #define ADIN1300_DOWNSPEED_RETRIES_MSK GENMASK(12, 10) |
| |
| #define ADIN1300_INT_MASK_REG 0x0018 |
| #define ADIN1300_INT_MDIO_SYNC_EN BIT(9) |
| #define ADIN1300_INT_ANEG_STAT_CHNG_EN BIT(8) |
| #define ADIN1300_INT_ANEG_PAGE_RX_EN BIT(6) |
| #define ADIN1300_INT_IDLE_ERR_CNT_EN BIT(5) |
| #define ADIN1300_INT_MAC_FIFO_OU_EN BIT(4) |
| #define ADIN1300_INT_RX_STAT_CHNG_EN BIT(3) |
| #define ADIN1300_INT_LINK_STAT_CHNG_EN BIT(2) |
| #define ADIN1300_INT_SPEED_CHNG_EN BIT(1) |
| #define ADIN1300_INT_HW_IRQ_EN BIT(0) |
| #define ADIN1300_INT_MASK_EN \ |
| (ADIN1300_INT_LINK_STAT_CHNG_EN | ADIN1300_INT_HW_IRQ_EN) |
| #define ADIN1300_INT_STATUS_REG 0x0019 |
| |
| #define ADIN1300_PHY_STATUS1 0x001a |
| #define ADIN1300_PAIR_01_SWAP BIT(11) |
| |
| /* EEE register addresses, accessible via Clause 22 access using |
| * ADIN1300_MII_EXT_REG_PTR & ADIN1300_MII_EXT_REG_DATA. |
| * The bit-fields are the same as specified by IEEE for EEE. |
| */ |
| #define ADIN1300_EEE_CAP_REG 0x8000 |
| #define ADIN1300_EEE_ADV_REG 0x8001 |
| #define ADIN1300_EEE_LPABLE_REG 0x8002 |
| #define ADIN1300_CLOCK_STOP_REG 0x9400 |
| #define ADIN1300_LPI_WAKE_ERR_CNT_REG 0xa000 |
| |
| #define ADIN1300_GE_SOFT_RESET_REG 0xff0c |
| #define ADIN1300_GE_SOFT_RESET BIT(0) |
| |
| #define ADIN1300_GE_RGMII_CFG_REG 0xff23 |
| #define ADIN1300_GE_RGMII_RX_MSK GENMASK(8, 6) |
| #define ADIN1300_GE_RGMII_RX_SEL(x) \ |
| FIELD_PREP(ADIN1300_GE_RGMII_RX_MSK, x) |
| #define ADIN1300_GE_RGMII_GTX_MSK GENMASK(5, 3) |
| #define ADIN1300_GE_RGMII_GTX_SEL(x) \ |
| FIELD_PREP(ADIN1300_GE_RGMII_GTX_MSK, x) |
| #define ADIN1300_GE_RGMII_RXID_EN BIT(2) |
| #define ADIN1300_GE_RGMII_TXID_EN BIT(1) |
| #define ADIN1300_GE_RGMII_EN BIT(0) |
| |
| /* RGMII internal delay settings for rx and tx for ADIN1300 */ |
| #define ADIN1300_RGMII_1_60_NS 0x0001 |
| #define ADIN1300_RGMII_1_80_NS 0x0002 |
| #define ADIN1300_RGMII_2_00_NS 0x0000 |
| #define ADIN1300_RGMII_2_20_NS 0x0006 |
| #define ADIN1300_RGMII_2_40_NS 0x0007 |
| |
| #define ADIN1300_GE_RMII_CFG_REG 0xff24 |
| #define ADIN1300_GE_RMII_FIFO_DEPTH_MSK GENMASK(6, 4) |
| #define ADIN1300_GE_RMII_FIFO_DEPTH_SEL(x) \ |
| FIELD_PREP(ADIN1300_GE_RMII_FIFO_DEPTH_MSK, x) |
| #define ADIN1300_GE_RMII_EN BIT(0) |
| |
| /* RMII fifo depth values */ |
| #define ADIN1300_RMII_4_BITS 0x0000 |
| #define ADIN1300_RMII_8_BITS 0x0001 |
| #define ADIN1300_RMII_12_BITS 0x0002 |
| #define ADIN1300_RMII_16_BITS 0x0003 |
| #define ADIN1300_RMII_20_BITS 0x0004 |
| #define ADIN1300_RMII_24_BITS 0x0005 |
| |
| /** |
| * struct adin_cfg_reg_map - map a config value to aregister value |
| * @cfg value in device configuration |
| * @reg value in the register |
| */ |
| struct adin_cfg_reg_map { |
| int cfg; |
| int reg; |
| }; |
| |
| static const struct adin_cfg_reg_map adin_rgmii_delays[] = { |
| { 1600, ADIN1300_RGMII_1_60_NS }, |
| { 1800, ADIN1300_RGMII_1_80_NS }, |
| { 2000, ADIN1300_RGMII_2_00_NS }, |
| { 2200, ADIN1300_RGMII_2_20_NS }, |
| { 2400, ADIN1300_RGMII_2_40_NS }, |
| { }, |
| }; |
| |
| static const struct adin_cfg_reg_map adin_rmii_fifo_depths[] = { |
| { 4, ADIN1300_RMII_4_BITS }, |
| { 8, ADIN1300_RMII_8_BITS }, |
| { 12, ADIN1300_RMII_12_BITS }, |
| { 16, ADIN1300_RMII_16_BITS }, |
| { 20, ADIN1300_RMII_20_BITS }, |
| { 24, ADIN1300_RMII_24_BITS }, |
| { }, |
| }; |
| |
| /** |
| * struct adin_clause45_mmd_map - map to convert Clause 45 regs to Clause 22 |
| * @devad device address used in Clause 45 access |
| * @cl45_regnum register address defined by Clause 45 |
| * @adin_regnum equivalent register address accessible via Clause 22 |
| */ |
| struct adin_clause45_mmd_map { |
| int devad; |
| u16 cl45_regnum; |
| u16 adin_regnum; |
| }; |
| |
| static const struct adin_clause45_mmd_map adin_clause45_mmd_map[] = { |
| { MDIO_MMD_PCS, MDIO_PCS_EEE_ABLE, ADIN1300_EEE_CAP_REG }, |
| { MDIO_MMD_AN, MDIO_AN_EEE_LPABLE, ADIN1300_EEE_LPABLE_REG }, |
| { MDIO_MMD_AN, MDIO_AN_EEE_ADV, ADIN1300_EEE_ADV_REG }, |
| { MDIO_MMD_PCS, MDIO_CTRL1, ADIN1300_CLOCK_STOP_REG }, |
| { MDIO_MMD_PCS, MDIO_PCS_EEE_WK_ERR, ADIN1300_LPI_WAKE_ERR_CNT_REG }, |
| }; |
| |
| struct adin_hw_stat { |
| const char *string; |
| u16 reg1; |
| u16 reg2; |
| }; |
| |
| static const struct adin_hw_stat adin_hw_stats[] = { |
| { "total_frames_checked_count", 0x940A, 0x940B }, /* hi + lo */ |
| { "length_error_frames_count", 0x940C }, |
| { "alignment_error_frames_count", 0x940D }, |
| { "symbol_error_count", 0x940E }, |
| { "oversized_frames_count", 0x940F }, |
| { "undersized_frames_count", 0x9410 }, |
| { "odd_nibble_frames_count", 0x9411 }, |
| { "odd_preamble_packet_count", 0x9412 }, |
| { "dribble_bits_frames_count", 0x9413 }, |
| { "false_carrier_events_count", 0x9414 }, |
| }; |
| |
| /** |
| * struct adin_priv - ADIN PHY driver private data |
| * stats statistic counters for the PHY |
| */ |
| struct adin_priv { |
| u64 stats[ARRAY_SIZE(adin_hw_stats)]; |
| }; |
| |
| static int adin_lookup_reg_value(const struct adin_cfg_reg_map *tbl, int cfg) |
| { |
| size_t i; |
| |
| for (i = 0; tbl[i].cfg; i++) { |
| if (tbl[i].cfg == cfg) |
| return tbl[i].reg; |
| } |
| |
| return -EINVAL; |
| } |
| |
| static u32 adin_get_reg_value(struct phy_device *phydev, |
| const char *prop_name, |
| const struct adin_cfg_reg_map *tbl, |
| u32 dflt) |
| { |
| struct device *dev = &phydev->mdio.dev; |
| u32 val; |
| int rc; |
| |
| if (device_property_read_u32(dev, prop_name, &val)) |
| return dflt; |
| |
| rc = adin_lookup_reg_value(tbl, val); |
| if (rc < 0) { |
| phydev_warn(phydev, |
| "Unsupported value %u for %s using default (%u)\n", |
| val, prop_name, dflt); |
| return dflt; |
| } |
| |
| return rc; |
| } |
| |
| static int adin_config_rgmii_mode(struct phy_device *phydev) |
| { |
| u32 val; |
| int reg; |
| |
| if (!phy_interface_is_rgmii(phydev)) |
| return phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, |
| ADIN1300_GE_RGMII_CFG_REG, |
| ADIN1300_GE_RGMII_EN); |
| |
| reg = phy_read_mmd(phydev, MDIO_MMD_VEND1, ADIN1300_GE_RGMII_CFG_REG); |
| if (reg < 0) |
| return reg; |
| |
| reg |= ADIN1300_GE_RGMII_EN; |
| |
| if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID || |
| phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID) { |
| reg |= ADIN1300_GE_RGMII_RXID_EN; |
| |
| val = adin_get_reg_value(phydev, "adi,rx-internal-delay-ps", |
| adin_rgmii_delays, |
| ADIN1300_RGMII_2_00_NS); |
| reg &= ~ADIN1300_GE_RGMII_RX_MSK; |
| reg |= ADIN1300_GE_RGMII_RX_SEL(val); |
| } else { |
| reg &= ~ADIN1300_GE_RGMII_RXID_EN; |
| } |
| |
| if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID || |
| phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID) { |
| reg |= ADIN1300_GE_RGMII_TXID_EN; |
| |
| val = adin_get_reg_value(phydev, "adi,tx-internal-delay-ps", |
| adin_rgmii_delays, |
| ADIN1300_RGMII_2_00_NS); |
| reg &= ~ADIN1300_GE_RGMII_GTX_MSK; |
| reg |= ADIN1300_GE_RGMII_GTX_SEL(val); |
| } else { |
| reg &= ~ADIN1300_GE_RGMII_TXID_EN; |
| } |
| |
| return phy_write_mmd(phydev, MDIO_MMD_VEND1, |
| ADIN1300_GE_RGMII_CFG_REG, reg); |
| } |
| |
| static int adin_config_rmii_mode(struct phy_device *phydev) |
| { |
| u32 val; |
| int reg; |
| |
| if (phydev->interface != PHY_INTERFACE_MODE_RMII) |
| return phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, |
| ADIN1300_GE_RMII_CFG_REG, |
| ADIN1300_GE_RMII_EN); |
| |
| reg = phy_read_mmd(phydev, MDIO_MMD_VEND1, ADIN1300_GE_RMII_CFG_REG); |
| if (reg < 0) |
| return reg; |
| |
| reg |= ADIN1300_GE_RMII_EN; |
| |
| val = adin_get_reg_value(phydev, "adi,fifo-depth-bits", |
| adin_rmii_fifo_depths, |
| ADIN1300_RMII_8_BITS); |
| |
| reg &= ~ADIN1300_GE_RMII_FIFO_DEPTH_MSK; |
| reg |= ADIN1300_GE_RMII_FIFO_DEPTH_SEL(val); |
| |
| return phy_write_mmd(phydev, MDIO_MMD_VEND1, |
| ADIN1300_GE_RMII_CFG_REG, reg); |
| } |
| |
| static int adin_get_downshift(struct phy_device *phydev, u8 *data) |
| { |
| int val, cnt, enable; |
| |
| val = phy_read(phydev, ADIN1300_PHY_CTRL2); |
| if (val < 0) |
| return val; |
| |
| cnt = phy_read(phydev, ADIN1300_PHY_CTRL3); |
| if (cnt < 0) |
| return cnt; |
| |
| enable = FIELD_GET(ADIN1300_DOWNSPEEDS_EN, val); |
| cnt = FIELD_GET(ADIN1300_DOWNSPEED_RETRIES_MSK, cnt); |
| |
| *data = (enable && cnt) ? cnt : DOWNSHIFT_DEV_DISABLE; |
| |
| return 0; |
| } |
| |
| static int adin_set_downshift(struct phy_device *phydev, u8 cnt) |
| { |
| u16 val; |
| int rc; |
| |
| if (cnt == DOWNSHIFT_DEV_DISABLE) |
| return phy_clear_bits(phydev, ADIN1300_PHY_CTRL2, |
| ADIN1300_DOWNSPEEDS_EN); |
| |
| if (cnt > 7) |
| return -E2BIG; |
| |
| val = FIELD_PREP(ADIN1300_DOWNSPEED_RETRIES_MSK, cnt); |
| val |= ADIN1300_LINKING_EN; |
| |
| rc = phy_modify(phydev, ADIN1300_PHY_CTRL3, |
| ADIN1300_LINKING_EN | ADIN1300_DOWNSPEED_RETRIES_MSK, |
| val); |
| if (rc < 0) |
| return rc; |
| |
| return phy_set_bits(phydev, ADIN1300_PHY_CTRL2, |
| ADIN1300_DOWNSPEEDS_EN); |
| } |
| |
| static int adin_get_edpd(struct phy_device *phydev, u16 *tx_interval) |
| { |
| int val; |
| |
| val = phy_read(phydev, ADIN1300_PHY_CTRL_STATUS2); |
| if (val < 0) |
| return val; |
| |
| if (ADIN1300_NRG_PD_EN & val) { |
| if (val & ADIN1300_NRG_PD_TX_EN) |
| /* default is 1 second */ |
| *tx_interval = ETHTOOL_PHY_EDPD_DFLT_TX_MSECS; |
| else |
| *tx_interval = ETHTOOL_PHY_EDPD_NO_TX; |
| } else { |
| *tx_interval = ETHTOOL_PHY_EDPD_DISABLE; |
| } |
| |
| return 0; |
| } |
| |
| static int adin_set_edpd(struct phy_device *phydev, u16 tx_interval) |
| { |
| u16 val; |
| |
| if (tx_interval == ETHTOOL_PHY_EDPD_DISABLE) |
| return phy_clear_bits(phydev, ADIN1300_PHY_CTRL_STATUS2, |
| (ADIN1300_NRG_PD_EN | ADIN1300_NRG_PD_TX_EN)); |
| |
| val = ADIN1300_NRG_PD_EN; |
| |
| switch (tx_interval) { |
| case 1000: /* 1 second */ |
| /* fallthrough */ |
| case ETHTOOL_PHY_EDPD_DFLT_TX_MSECS: |
| val |= ADIN1300_NRG_PD_TX_EN; |
| /* fallthrough */ |
| case ETHTOOL_PHY_EDPD_NO_TX: |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| return phy_modify(phydev, ADIN1300_PHY_CTRL_STATUS2, |
| (ADIN1300_NRG_PD_EN | ADIN1300_NRG_PD_TX_EN), |
| val); |
| } |
| |
| static int adin_get_tunable(struct phy_device *phydev, |
| struct ethtool_tunable *tuna, void *data) |
| { |
| switch (tuna->id) { |
| case ETHTOOL_PHY_DOWNSHIFT: |
| return adin_get_downshift(phydev, data); |
| case ETHTOOL_PHY_EDPD: |
| return adin_get_edpd(phydev, data); |
| default: |
| return -EOPNOTSUPP; |
| } |
| } |
| |
| static int adin_set_tunable(struct phy_device *phydev, |
| struct ethtool_tunable *tuna, const void *data) |
| { |
| switch (tuna->id) { |
| case ETHTOOL_PHY_DOWNSHIFT: |
| return adin_set_downshift(phydev, *(const u8 *)data); |
| case ETHTOOL_PHY_EDPD: |
| return adin_set_edpd(phydev, *(const u16 *)data); |
| default: |
| return -EOPNOTSUPP; |
| } |
| } |
| |
| static int adin_config_init(struct phy_device *phydev) |
| { |
| int rc; |
| |
| phydev->mdix_ctrl = ETH_TP_MDI_AUTO; |
| |
| rc = adin_config_rgmii_mode(phydev); |
| if (rc < 0) |
| return rc; |
| |
| rc = adin_config_rmii_mode(phydev); |
| if (rc < 0) |
| return rc; |
| |
| rc = adin_set_downshift(phydev, 4); |
| if (rc < 0) |
| return rc; |
| |
| rc = adin_set_edpd(phydev, ETHTOOL_PHY_EDPD_DFLT_TX_MSECS); |
| if (rc < 0) |
| return rc; |
| |
| phydev_dbg(phydev, "PHY is using mode '%s'\n", |
| phy_modes(phydev->interface)); |
| |
| return 0; |
| } |
| |
| static int adin_phy_ack_intr(struct phy_device *phydev) |
| { |
| /* Clear pending interrupts */ |
| int rc = phy_read(phydev, ADIN1300_INT_STATUS_REG); |
| |
| return rc < 0 ? rc : 0; |
| } |
| |
| static int adin_phy_config_intr(struct phy_device *phydev) |
| { |
| if (phydev->interrupts == PHY_INTERRUPT_ENABLED) |
| return phy_set_bits(phydev, ADIN1300_INT_MASK_REG, |
| ADIN1300_INT_MASK_EN); |
| |
| return phy_clear_bits(phydev, ADIN1300_INT_MASK_REG, |
| ADIN1300_INT_MASK_EN); |
| } |
| |
| static int adin_cl45_to_adin_reg(struct phy_device *phydev, int devad, |
| u16 cl45_regnum) |
| { |
| const struct adin_clause45_mmd_map *m; |
| int i; |
| |
| if (devad == MDIO_MMD_VEND1) |
| return cl45_regnum; |
| |
| for (i = 0; i < ARRAY_SIZE(adin_clause45_mmd_map); i++) { |
| m = &adin_clause45_mmd_map[i]; |
| if (m->devad == devad && m->cl45_regnum == cl45_regnum) |
| return m->adin_regnum; |
| } |
| |
| phydev_err(phydev, |
| "No translation available for devad: %d reg: %04x\n", |
| devad, cl45_regnum); |
| |
| return -EINVAL; |
| } |
| |
| static int adin_read_mmd(struct phy_device *phydev, int devad, u16 regnum) |
| { |
| struct mii_bus *bus = phydev->mdio.bus; |
| int phy_addr = phydev->mdio.addr; |
| int adin_regnum; |
| int err; |
| |
| adin_regnum = adin_cl45_to_adin_reg(phydev, devad, regnum); |
| if (adin_regnum < 0) |
| return adin_regnum; |
| |
| err = __mdiobus_write(bus, phy_addr, ADIN1300_MII_EXT_REG_PTR, |
| adin_regnum); |
| if (err) |
| return err; |
| |
| return __mdiobus_read(bus, phy_addr, ADIN1300_MII_EXT_REG_DATA); |
| } |
| |
| static int adin_write_mmd(struct phy_device *phydev, int devad, u16 regnum, |
| u16 val) |
| { |
| struct mii_bus *bus = phydev->mdio.bus; |
| int phy_addr = phydev->mdio.addr; |
| int adin_regnum; |
| int err; |
| |
| adin_regnum = adin_cl45_to_adin_reg(phydev, devad, regnum); |
| if (adin_regnum < 0) |
| return adin_regnum; |
| |
| err = __mdiobus_write(bus, phy_addr, ADIN1300_MII_EXT_REG_PTR, |
| adin_regnum); |
| if (err) |
| return err; |
| |
| return __mdiobus_write(bus, phy_addr, ADIN1300_MII_EXT_REG_DATA, val); |
| } |
| |
| static int adin_config_mdix(struct phy_device *phydev) |
| { |
| bool auto_en, mdix_en; |
| int reg; |
| |
| mdix_en = false; |
| auto_en = false; |
| switch (phydev->mdix_ctrl) { |
| case ETH_TP_MDI: |
| break; |
| case ETH_TP_MDI_X: |
| mdix_en = true; |
| break; |
| case ETH_TP_MDI_AUTO: |
| auto_en = true; |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| reg = phy_read(phydev, ADIN1300_PHY_CTRL1); |
| if (reg < 0) |
| return reg; |
| |
| if (mdix_en) |
| reg |= ADIN1300_MAN_MDIX_EN; |
| else |
| reg &= ~ADIN1300_MAN_MDIX_EN; |
| |
| if (auto_en) |
| reg |= ADIN1300_AUTO_MDI_EN; |
| else |
| reg &= ~ADIN1300_AUTO_MDI_EN; |
| |
| return phy_write(phydev, ADIN1300_PHY_CTRL1, reg); |
| } |
| |
| static int adin_config_aneg(struct phy_device *phydev) |
| { |
| int ret; |
| |
| ret = adin_config_mdix(phydev); |
| if (ret) |
| return ret; |
| |
| return genphy_config_aneg(phydev); |
| } |
| |
| static int adin_mdix_update(struct phy_device *phydev) |
| { |
| bool auto_en, mdix_en; |
| bool swapped; |
| int reg; |
| |
| reg = phy_read(phydev, ADIN1300_PHY_CTRL1); |
| if (reg < 0) |
| return reg; |
| |
| auto_en = !!(reg & ADIN1300_AUTO_MDI_EN); |
| mdix_en = !!(reg & ADIN1300_MAN_MDIX_EN); |
| |
| /* If MDI/MDIX is forced, just read it from the control reg */ |
| if (!auto_en) { |
| if (mdix_en) |
| phydev->mdix = ETH_TP_MDI_X; |
| else |
| phydev->mdix = ETH_TP_MDI; |
| return 0; |
| } |
| |
| /** |
| * Otherwise, we need to deduce it from the PHY status2 reg. |
| * When Auto-MDI is enabled, the ADIN1300_MAN_MDIX_EN bit implies |
| * a preference for MDIX when it is set. |
| */ |
| reg = phy_read(phydev, ADIN1300_PHY_STATUS1); |
| if (reg < 0) |
| return reg; |
| |
| swapped = !!(reg & ADIN1300_PAIR_01_SWAP); |
| |
| if (mdix_en != swapped) |
| phydev->mdix = ETH_TP_MDI_X; |
| else |
| phydev->mdix = ETH_TP_MDI; |
| |
| return 0; |
| } |
| |
| static int adin_read_status(struct phy_device *phydev) |
| { |
| int ret; |
| |
| ret = adin_mdix_update(phydev); |
| if (ret < 0) |
| return ret; |
| |
| return genphy_read_status(phydev); |
| } |
| |
| static int adin_soft_reset(struct phy_device *phydev) |
| { |
| int rc; |
| |
| /* The reset bit is self-clearing, set it and wait */ |
| rc = phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, |
| ADIN1300_GE_SOFT_RESET_REG, |
| ADIN1300_GE_SOFT_RESET); |
| if (rc < 0) |
| return rc; |
| |
| msleep(20); |
| |
| /* If we get a read error something may be wrong */ |
| rc = phy_read_mmd(phydev, MDIO_MMD_VEND1, |
| ADIN1300_GE_SOFT_RESET_REG); |
| |
| return rc < 0 ? rc : 0; |
| } |
| |
| static int adin_get_sset_count(struct phy_device *phydev) |
| { |
| return ARRAY_SIZE(adin_hw_stats); |
| } |
| |
| static void adin_get_strings(struct phy_device *phydev, u8 *data) |
| { |
| int i; |
| |
| for (i = 0; i < ARRAY_SIZE(adin_hw_stats); i++) { |
| strlcpy(&data[i * ETH_GSTRING_LEN], |
| adin_hw_stats[i].string, ETH_GSTRING_LEN); |
| } |
| } |
| |
| static int adin_read_mmd_stat_regs(struct phy_device *phydev, |
| const struct adin_hw_stat *stat, |
| u32 *val) |
| { |
| int ret; |
| |
| ret = phy_read_mmd(phydev, MDIO_MMD_VEND1, stat->reg1); |
| if (ret < 0) |
| return ret; |
| |
| *val = (ret & 0xffff); |
| |
| if (stat->reg2 == 0) |
| return 0; |
| |
| ret = phy_read_mmd(phydev, MDIO_MMD_VEND1, stat->reg2); |
| if (ret < 0) |
| return ret; |
| |
| *val <<= 16; |
| *val |= (ret & 0xffff); |
| |
| return 0; |
| } |
| |
| static u64 adin_get_stat(struct phy_device *phydev, int i) |
| { |
| const struct adin_hw_stat *stat = &adin_hw_stats[i]; |
| struct adin_priv *priv = phydev->priv; |
| u32 val; |
| int ret; |
| |
| if (stat->reg1 > 0x1f) { |
| ret = adin_read_mmd_stat_regs(phydev, stat, &val); |
| if (ret < 0) |
| return (u64)(~0); |
| } else { |
| ret = phy_read(phydev, stat->reg1); |
| if (ret < 0) |
| return (u64)(~0); |
| val = (ret & 0xffff); |
| } |
| |
| priv->stats[i] += val; |
| |
| return priv->stats[i]; |
| } |
| |
| static void adin_get_stats(struct phy_device *phydev, |
| struct ethtool_stats *stats, u64 *data) |
| { |
| int i, rc; |
| |
| /* latch copies of all the frame-checker counters */ |
| rc = phy_read(phydev, ADIN1300_RX_ERR_CNT); |
| if (rc < 0) |
| return; |
| |
| for (i = 0; i < ARRAY_SIZE(adin_hw_stats); i++) |
| data[i] = adin_get_stat(phydev, i); |
| } |
| |
| static int adin_probe(struct phy_device *phydev) |
| { |
| struct device *dev = &phydev->mdio.dev; |
| struct adin_priv *priv; |
| |
| priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); |
| if (!priv) |
| return -ENOMEM; |
| |
| phydev->priv = priv; |
| |
| return 0; |
| } |
| |
| static struct phy_driver adin_driver[] = { |
| { |
| PHY_ID_MATCH_MODEL(PHY_ID_ADIN1200), |
| .name = "ADIN1200", |
| .probe = adin_probe, |
| .config_init = adin_config_init, |
| .soft_reset = adin_soft_reset, |
| .config_aneg = adin_config_aneg, |
| .read_status = adin_read_status, |
| .get_tunable = adin_get_tunable, |
| .set_tunable = adin_set_tunable, |
| .ack_interrupt = adin_phy_ack_intr, |
| .config_intr = adin_phy_config_intr, |
| .get_sset_count = adin_get_sset_count, |
| .get_strings = adin_get_strings, |
| .get_stats = adin_get_stats, |
| .resume = genphy_resume, |
| .suspend = genphy_suspend, |
| .read_mmd = adin_read_mmd, |
| .write_mmd = adin_write_mmd, |
| }, |
| { |
| PHY_ID_MATCH_MODEL(PHY_ID_ADIN1300), |
| .name = "ADIN1300", |
| .probe = adin_probe, |
| .config_init = adin_config_init, |
| .soft_reset = adin_soft_reset, |
| .config_aneg = adin_config_aneg, |
| .read_status = adin_read_status, |
| .get_tunable = adin_get_tunable, |
| .set_tunable = adin_set_tunable, |
| .ack_interrupt = adin_phy_ack_intr, |
| .config_intr = adin_phy_config_intr, |
| .get_sset_count = adin_get_sset_count, |
| .get_strings = adin_get_strings, |
| .get_stats = adin_get_stats, |
| .resume = genphy_resume, |
| .suspend = genphy_suspend, |
| .read_mmd = adin_read_mmd, |
| .write_mmd = adin_write_mmd, |
| }, |
| }; |
| |
| module_phy_driver(adin_driver); |
| |
| static struct mdio_device_id __maybe_unused adin_tbl[] = { |
| { PHY_ID_MATCH_MODEL(PHY_ID_ADIN1200) }, |
| { PHY_ID_MATCH_MODEL(PHY_ID_ADIN1300) }, |
| { } |
| }; |
| |
| MODULE_DEVICE_TABLE(mdio, adin_tbl); |
| MODULE_DESCRIPTION("Analog Devices Industrial Ethernet PHY driver"); |
| MODULE_LICENSE("GPL"); |