| Qualcomm SPMI Regulators |
| |
| - compatible: |
| Usage: required |
| Value type: <string> |
| Definition: must be one of: |
| "qcom,pm8004-regulators" |
| "qcom,pm8005-regulators" |
| "qcom,pm8841-regulators" |
| "qcom,pm8916-regulators" |
| "qcom,pm8941-regulators" |
| "qcom,pm8950-regulators" |
| "qcom,pm8994-regulators" |
| "qcom,pmi8994-regulators" |
| "qcom,pm660-regulators" |
| "qcom,pm660l-regulators" |
| "qcom,pms405-regulators" |
| |
| - interrupts: |
| Usage: optional |
| Value type: <prop-encoded-array> |
| Definition: List of OCP interrupts. |
| |
| - interrupt-names: |
| Usage: required if 'interrupts' property present |
| Value type: <string-array> |
| Definition: List of strings defining the names of the |
| interrupts in the 'interrupts' property 1-to-1. |
| Supported values are "ocp-<regulator_name>", where |
| <regulator_name> corresponds to a voltage switch |
| type regulator. |
| |
| - vdd_s1-supply: |
| - vdd_s2-supply: |
| - vdd_s3-supply: |
| - vdd_s4-supply: |
| - vdd_s5-supply: |
| - vdd_s6-supply: |
| - vdd_s7-supply: |
| - vdd_s8-supply: |
| Usage: optional (pm8841 only) |
| Value type: <phandle> |
| Definition: Reference to regulator supplying the input pin, as |
| described in the data sheet. |
| |
| - vdd_s1-supply: |
| - vdd_s2-supply: |
| - vdd_s3-supply: |
| - vdd_s4-supply: |
| - vdd_l1_l3-supply: |
| - vdd_l2-supply: |
| - vdd_l4_l5_l6-supply: |
| - vdd_l7-supply: |
| - vdd_l8_l11_l14_l15_l16-supply: |
| - vdd_l9_l10_l12_l13_l17_l18-supply: |
| Usage: optional (pm8916 only) |
| Value type: <phandle> |
| Definition: Reference to regulator supplying the input pin, as |
| described in the data sheet. |
| |
| - vdd_s1-supply: |
| - vdd_s2-supply: |
| - vdd_s3-supply: |
| - vdd_l1_l3-supply: |
| - vdd_l2_lvs_1_2_3-supply: |
| - vdd_l4_l11-supply: |
| - vdd_l5_l7-supply: |
| - vdd_l6_l12_l14_l15-supply: |
| - vdd_l8_l16_l18_19-supply: |
| - vdd_l9_l10_l17_l22-supply: |
| - vdd_l13_l20_l23_l24-supply: |
| - vdd_l21-supply: |
| - vin_5vs-supply: |
| Usage: optional (pm8941 only) |
| Value type: <phandle> |
| Definition: Reference to regulator supplying the input pin, as |
| described in the data sheet. |
| |
| - vdd_s1-supply: |
| - vdd_s2-supply: |
| - vdd_s3-supply: |
| - vdd_s4-supply: |
| - vdd_s4-supply: |
| - vdd_s5-supply: |
| - vdd_s6-supply: |
| - vdd_l1_l19-supply: |
| - vdd_l2_l23-supply: |
| - vdd_l3-supply: |
| - vdd_l4_l5_l6_l7_l16-supply: |
| - vdd_l8_l11_l12_l17_l22-supply: |
| - vdd_l9_l10_l13_l14_l15_l18-supply: |
| - vdd_l20-supply: |
| - vdd_l21-supply: |
| Usage: optional (pm8950 only) |
| Value type: <phandle> |
| Definition: reference to regulator supplying the input pin, as |
| described in the data sheet |
| |
| - vdd_s1-supply: |
| - vdd_s2-supply: |
| - vdd_s3-supply: |
| - vdd_s4-supply: |
| - vdd_s5-supply: |
| - vdd_s6-supply: |
| - vdd_s7-supply: |
| - vdd_s8-supply: |
| - vdd_s9-supply: |
| - vdd_s10-supply: |
| - vdd_s11-supply: |
| - vdd_s12-supply: |
| - vdd_l1-supply: |
| - vdd_l2_l26_l28-supply: |
| - vdd_l3_l11-supply: |
| - vdd_l4_l27_l31-supply: |
| - vdd_l5_l7-supply: |
| - vdd_l6_l12_l32-supply: |
| - vdd_l8_l16_l30-supply: |
| - vdd_l9_l10_l18_l22-supply: |
| - vdd_l13_l19_l23_l24-supply: |
| - vdd_l14_l15-supply: |
| - vdd_l17_l29-supply: |
| - vdd_l20_l21-supply: |
| - vdd_l25-supply: |
| - vdd_lvs_1_2-supply: |
| Usage: optional (pm8994 only) |
| Value type: <phandle> |
| Definition: Reference to regulator supplying the input pin, as |
| described in the data sheet. |
| |
| - vdd_s1-supply: |
| - vdd_s2-supply: |
| - vdd_s3-supply: |
| - vdd_l1-supply: |
| Usage: optional (pmi8994 only) |
| Value type: <phandle> |
| Definition: Reference to regulator supplying the input pin, as |
| described in the data sheet. |
| |
| - vdd_l1_l6_l7-supply: |
| - vdd_l2_l3-supply: |
| - vdd_l5-supply: |
| - vdd_l8_l9_l10_l11_l12_l13_l14-supply: |
| - vdd_l15_l16_l17_l18_l19-supply: |
| - vdd_s1-supply: |
| - vdd_s2-supply: |
| - vdd_s3-supply: |
| - vdd_s5-supply: |
| - vdd_s6-supply: |
| Usage: optional (pm660 only) |
| Value type: <phandle> |
| Definition: Reference to regulator supplying the input pin, as |
| described in the data sheet. |
| |
| - vdd_l1_l9_l10-supply: |
| - vdd_l2-supply: |
| - vdd_l3_l5_l7_l8-supply: |
| - vdd_l4_l6-supply: |
| - vdd_s1-supply: |
| - vdd_s2-supply: |
| - vdd_s3-supply: |
| - vdd_s4-supply: |
| - vdd_s5-supply: |
| Usage: optional (pm660l only) |
| Value type: <phandle> |
| Definition: Reference to regulator supplying the input pin, as |
| described in the data sheet. |
| |
| - vdd_l1_l2-supply: |
| - vdd_l3_l8-supply: |
| - vdd_l4-supply: |
| - vdd_l5_l6-supply: |
| - vdd_l10_l11_l12_l13-supply: |
| - vdd_l7-supply: |
| - vdd_l9-supply: |
| - vdd_s1-supply: |
| - vdd_s2-supply: |
| - vdd_s3-supply: |
| - vdd_s4-supply: |
| - vdd_s5-supply |
| Usage: optional (pms405 only) |
| Value type: <phandle> |
| Definition: Reference to regulator supplying the input pin, as |
| described in the data sheet. |
| |
| - qcom,saw-reg: |
| Usage: optional |
| Value type: <phandle> |
| Description: Reference to syscon node defining the SAW registers. |
| |
| |
| The regulator node houses sub-nodes for each regulator within the device. Each |
| sub-node is identified using the node's name, with valid values listed for each |
| of the PMICs below. |
| |
| pm8004: |
| s2, s5 |
| |
| pm8005: |
| s1, s2, s3, s4 |
| |
| pm8841: |
| s1, s2, s3, s4, s5, s6, s7, s8 |
| |
| pm8916: |
| s1, s2, s3, s4, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13, |
| l14, l15, l16, l17, l18 |
| |
| pm8941: |
| s1, s2, s3, s4, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13, |
| l14, l15, l16, l17, l18, l19, l20, l21, l22, l23, l24, lvs1, lvs2, lvs3, |
| 5vs1, 5vs2 |
| |
| pm8994: |
| s1, s2, s3, s4, s5, s6, s7, s8, s9, s10, s11, s12, l1, l2, l3, l4, l5, |
| l6, l7, l8, l9, l10, l11, l12, l13, l14, l15, l16, l17, l18, l19, l20, |
| l21, l22, l23, l24, l25, l26, l27, l28, l29, l30, l31, l32, lvs1, lvs2 |
| |
| pmi8994: |
| s1, s2, s3, l1 |
| |
| The content of each sub-node is defined by the standard binding for regulators - |
| see regulator.txt - with additional custom properties described below: |
| |
| - regulator-initial-mode: |
| Usage: optional |
| Value type: <u32> |
| Description: 2 = Set initial mode to auto mode (automatically select |
| between HPM and LPM); not available on boost type |
| regulators. |
| |
| 1 = Set initial mode to high power mode (HPM), also referred |
| to as NPM. HPM consumes more ground current than LPM, but |
| it can source significantly higher load current. HPM is not |
| available on boost type regulators. For voltage switch type |
| regulators, HPM implies that over current protection and |
| soft start are active all the time. |
| |
| 0 = Set initial mode to low power mode (LPM). |
| |
| - qcom,ocp-max-retries: |
| Usage: optional |
| Value type: <u32> |
| Description: Maximum number of times to try toggling a voltage switch |
| off and back on as a result of consecutive over current |
| events. |
| |
| - qcom,ocp-retry-delay: |
| Usage: optional |
| Value type: <u32> |
| Description: Time to delay in milliseconds between each voltage switch |
| toggle after an over current event takes place. |
| |
| - qcom,pin-ctrl-enable: |
| Usage: optional |
| Value type: <u32> |
| Description: Bit mask specifying which hardware pins should be used to |
| enable the regulator, if any; supported bits are: |
| 0 = ignore all hardware enable signals |
| BIT(0) = follow HW0_EN signal |
| BIT(1) = follow HW1_EN signal |
| BIT(2) = follow HW2_EN signal |
| BIT(3) = follow HW3_EN signal |
| |
| - qcom,pin-ctrl-hpm: |
| Usage: optional |
| Value type: <u32> |
| Description: Bit mask specifying which hardware pins should be used to |
| force the regulator into high power mode, if any; |
| supported bits are: |
| 0 = ignore all hardware enable signals |
| BIT(0) = follow HW0_EN signal |
| BIT(1) = follow HW1_EN signal |
| BIT(2) = follow HW2_EN signal |
| BIT(3) = follow HW3_EN signal |
| BIT(4) = follow PMIC awake state |
| |
| - qcom,vs-soft-start-strength: |
| Usage: optional |
| Value type: <u32> |
| Description: This property sets the soft start strength for voltage |
| switch type regulators; supported values are: |
| 0 = 0.05 uA |
| 1 = 0.25 uA |
| 2 = 0.55 uA |
| 3 = 0.75 uA |
| |
| - qcom,saw-slave: |
| Usage: optional |
| Value type: <boo> |
| Description: SAW controlled gang slave. Will not be configured. |
| |
| - qcom,saw-leader: |
| Usage: optional |
| Value type: <boo> |
| Description: SAW controlled gang leader. Will be configured as |
| SAW regulator. |
| |
| Example: |
| |
| regulators { |
| compatible = "qcom,pm8941-regulators"; |
| vdd_l1_l3-supply = <&s1>; |
| |
| s1: s1 { |
| regulator-min-microvolt = <1300000>; |
| regulator-max-microvolt = <1400000>; |
| }; |
| |
| ... |
| |
| l1: l1 { |
| regulator-min-microvolt = <1225000>; |
| regulator-max-microvolt = <1300000>; |
| }; |
| |
| .... |
| }; |
| |
| Example 2: |
| |
| saw3: syscon@9A10000 { |
| compatible = "syscon"; |
| reg = <0x9A10000 0x1000>; |
| }; |
| |
| ... |
| |
| spm-regulators { |
| compatible = "qcom,pm8994-regulators"; |
| qcom,saw-reg = <&saw3>; |
| s8 { |
| qcom,saw-slave; |
| }; |
| s9 { |
| qcom,saw-slave; |
| }; |
| s10 { |
| qcom,saw-slave; |
| }; |
| pm8994_s11_saw: s11 { |
| qcom,saw-leader; |
| regulator-always-on; |
| regulator-min-microvolt = <900000>; |
| regulator-max-microvolt = <1140000>; |
| }; |
| }; |
