| // SPDX-License-Identifier: GPL-2.0-or-later |
| /* |
| * Sony CXD2820R demodulator driver |
| * |
| * Copyright (C) 2010 Antti Palosaari <crope@iki.fi> |
| */ |
| |
| |
| #include "cxd2820r_priv.h" |
| |
| /* Write register table */ |
| int cxd2820r_wr_reg_val_mask_tab(struct cxd2820r_priv *priv, |
| const struct reg_val_mask *tab, int tab_len) |
| { |
| struct i2c_client *client = priv->client[0]; |
| int ret; |
| unsigned int i, reg, mask, val; |
| struct regmap *regmap; |
| |
| dev_dbg(&client->dev, "tab_len=%d\n", tab_len); |
| |
| for (i = 0; i < tab_len; i++) { |
| if ((tab[i].reg >> 16) & 0x1) |
| regmap = priv->regmap[1]; |
| else |
| regmap = priv->regmap[0]; |
| |
| reg = (tab[i].reg >> 0) & 0xffff; |
| val = tab[i].val; |
| mask = tab[i].mask; |
| |
| if (mask == 0xff) |
| ret = regmap_write(regmap, reg, val); |
| else |
| ret = regmap_write_bits(regmap, reg, mask, val); |
| if (ret) |
| goto error; |
| } |
| |
| return 0; |
| error: |
| dev_dbg(&client->dev, "failed=%d\n", ret); |
| return ret; |
| } |
| |
| int cxd2820r_gpio(struct dvb_frontend *fe, u8 *gpio) |
| { |
| struct cxd2820r_priv *priv = fe->demodulator_priv; |
| struct i2c_client *client = priv->client[0]; |
| struct dtv_frontend_properties *c = &fe->dtv_property_cache; |
| int ret, i; |
| u8 tmp0, tmp1; |
| |
| dev_dbg(&client->dev, "delivery_system=%d\n", c->delivery_system); |
| |
| /* update GPIOs only when needed */ |
| if (!memcmp(gpio, priv->gpio, sizeof(priv->gpio))) |
| return 0; |
| |
| tmp0 = 0x00; |
| tmp1 = 0x00; |
| for (i = 0; i < sizeof(priv->gpio); i++) { |
| /* enable / disable */ |
| if (gpio[i] & CXD2820R_GPIO_E) |
| tmp0 |= (2 << 6) >> (2 * i); |
| else |
| tmp0 |= (1 << 6) >> (2 * i); |
| |
| /* input / output */ |
| if (gpio[i] & CXD2820R_GPIO_I) |
| tmp1 |= (1 << (3 + i)); |
| else |
| tmp1 |= (0 << (3 + i)); |
| |
| /* high / low */ |
| if (gpio[i] & CXD2820R_GPIO_H) |
| tmp1 |= (1 << (0 + i)); |
| else |
| tmp1 |= (0 << (0 + i)); |
| |
| dev_dbg(&client->dev, "gpio i=%d %02x %02x\n", i, tmp0, tmp1); |
| } |
| |
| dev_dbg(&client->dev, "wr gpio=%02x %02x\n", tmp0, tmp1); |
| |
| /* write bits [7:2] */ |
| ret = regmap_update_bits(priv->regmap[0], 0x0089, 0xfc, tmp0); |
| if (ret) |
| goto error; |
| |
| /* write bits [5:0] */ |
| ret = regmap_update_bits(priv->regmap[0], 0x008e, 0x3f, tmp1); |
| if (ret) |
| goto error; |
| |
| memcpy(priv->gpio, gpio, sizeof(priv->gpio)); |
| |
| return ret; |
| error: |
| dev_dbg(&client->dev, "failed=%d\n", ret); |
| return ret; |
| } |
| |
| static int cxd2820r_set_frontend(struct dvb_frontend *fe) |
| { |
| struct cxd2820r_priv *priv = fe->demodulator_priv; |
| struct i2c_client *client = priv->client[0]; |
| struct dtv_frontend_properties *c = &fe->dtv_property_cache; |
| int ret; |
| |
| dev_dbg(&client->dev, "delivery_system=%d\n", c->delivery_system); |
| |
| switch (c->delivery_system) { |
| case SYS_DVBT: |
| ret = cxd2820r_init_t(fe); |
| if (ret < 0) |
| goto err; |
| ret = cxd2820r_set_frontend_t(fe); |
| if (ret < 0) |
| goto err; |
| break; |
| case SYS_DVBT2: |
| ret = cxd2820r_init_t(fe); |
| if (ret < 0) |
| goto err; |
| ret = cxd2820r_set_frontend_t2(fe); |
| if (ret < 0) |
| goto err; |
| break; |
| case SYS_DVBC_ANNEX_A: |
| ret = cxd2820r_init_c(fe); |
| if (ret < 0) |
| goto err; |
| ret = cxd2820r_set_frontend_c(fe); |
| if (ret < 0) |
| goto err; |
| break; |
| default: |
| dev_dbg(&client->dev, "invalid delivery_system\n"); |
| ret = -EINVAL; |
| break; |
| } |
| err: |
| return ret; |
| } |
| |
| static int cxd2820r_read_status(struct dvb_frontend *fe, enum fe_status *status) |
| { |
| struct cxd2820r_priv *priv = fe->demodulator_priv; |
| struct i2c_client *client = priv->client[0]; |
| struct dtv_frontend_properties *c = &fe->dtv_property_cache; |
| int ret; |
| |
| dev_dbg(&client->dev, "delivery_system=%d\n", c->delivery_system); |
| |
| switch (c->delivery_system) { |
| case SYS_DVBT: |
| ret = cxd2820r_read_status_t(fe, status); |
| break; |
| case SYS_DVBT2: |
| ret = cxd2820r_read_status_t2(fe, status); |
| break; |
| case SYS_DVBC_ANNEX_A: |
| ret = cxd2820r_read_status_c(fe, status); |
| break; |
| default: |
| ret = -EINVAL; |
| break; |
| } |
| return ret; |
| } |
| |
| static int cxd2820r_get_frontend(struct dvb_frontend *fe, |
| struct dtv_frontend_properties *p) |
| { |
| struct cxd2820r_priv *priv = fe->demodulator_priv; |
| struct i2c_client *client = priv->client[0]; |
| struct dtv_frontend_properties *c = &fe->dtv_property_cache; |
| int ret; |
| |
| dev_dbg(&client->dev, "delivery_system=%d\n", c->delivery_system); |
| |
| if (priv->delivery_system == SYS_UNDEFINED) |
| return 0; |
| |
| switch (c->delivery_system) { |
| case SYS_DVBT: |
| ret = cxd2820r_get_frontend_t(fe, p); |
| break; |
| case SYS_DVBT2: |
| ret = cxd2820r_get_frontend_t2(fe, p); |
| break; |
| case SYS_DVBC_ANNEX_A: |
| ret = cxd2820r_get_frontend_c(fe, p); |
| break; |
| default: |
| ret = -EINVAL; |
| break; |
| } |
| return ret; |
| } |
| |
| static int cxd2820r_read_ber(struct dvb_frontend *fe, u32 *ber) |
| { |
| struct cxd2820r_priv *priv = fe->demodulator_priv; |
| struct i2c_client *client = priv->client[0]; |
| struct dtv_frontend_properties *c = &fe->dtv_property_cache; |
| |
| dev_dbg(&client->dev, "delivery_system=%d\n", c->delivery_system); |
| |
| *ber = (priv->post_bit_error - priv->post_bit_error_prev_dvbv3); |
| priv->post_bit_error_prev_dvbv3 = priv->post_bit_error; |
| |
| return 0; |
| } |
| |
| static int cxd2820r_read_signal_strength(struct dvb_frontend *fe, u16 *strength) |
| { |
| struct cxd2820r_priv *priv = fe->demodulator_priv; |
| struct i2c_client *client = priv->client[0]; |
| struct dtv_frontend_properties *c = &fe->dtv_property_cache; |
| |
| dev_dbg(&client->dev, "delivery_system=%d\n", c->delivery_system); |
| |
| if (c->strength.stat[0].scale == FE_SCALE_RELATIVE) |
| *strength = c->strength.stat[0].uvalue; |
| else |
| *strength = 0; |
| |
| return 0; |
| } |
| |
| static int cxd2820r_read_snr(struct dvb_frontend *fe, u16 *snr) |
| { |
| struct cxd2820r_priv *priv = fe->demodulator_priv; |
| struct i2c_client *client = priv->client[0]; |
| struct dtv_frontend_properties *c = &fe->dtv_property_cache; |
| |
| dev_dbg(&client->dev, "delivery_system=%d\n", c->delivery_system); |
| |
| if (c->cnr.stat[0].scale == FE_SCALE_DECIBEL) |
| *snr = div_s64(c->cnr.stat[0].svalue, 100); |
| else |
| *snr = 0; |
| |
| return 0; |
| } |
| |
| static int cxd2820r_read_ucblocks(struct dvb_frontend *fe, u32 *ucblocks) |
| { |
| struct cxd2820r_priv *priv = fe->demodulator_priv; |
| struct i2c_client *client = priv->client[0]; |
| struct dtv_frontend_properties *c = &fe->dtv_property_cache; |
| |
| dev_dbg(&client->dev, "delivery_system=%d\n", c->delivery_system); |
| |
| *ucblocks = 0; |
| |
| return 0; |
| } |
| |
| static int cxd2820r_init(struct dvb_frontend *fe) |
| { |
| return 0; |
| } |
| |
| static int cxd2820r_sleep(struct dvb_frontend *fe) |
| { |
| struct cxd2820r_priv *priv = fe->demodulator_priv; |
| struct i2c_client *client = priv->client[0]; |
| struct dtv_frontend_properties *c = &fe->dtv_property_cache; |
| int ret; |
| |
| dev_dbg(&client->dev, "delivery_system=%d\n", c->delivery_system); |
| |
| switch (c->delivery_system) { |
| case SYS_DVBT: |
| ret = cxd2820r_sleep_t(fe); |
| break; |
| case SYS_DVBT2: |
| ret = cxd2820r_sleep_t2(fe); |
| break; |
| case SYS_DVBC_ANNEX_A: |
| ret = cxd2820r_sleep_c(fe); |
| break; |
| default: |
| ret = -EINVAL; |
| break; |
| } |
| return ret; |
| } |
| |
| static int cxd2820r_get_tune_settings(struct dvb_frontend *fe, |
| struct dvb_frontend_tune_settings *s) |
| { |
| struct cxd2820r_priv *priv = fe->demodulator_priv; |
| struct i2c_client *client = priv->client[0]; |
| struct dtv_frontend_properties *c = &fe->dtv_property_cache; |
| int ret; |
| |
| dev_dbg(&client->dev, "delivery_system=%d\n", c->delivery_system); |
| |
| switch (c->delivery_system) { |
| case SYS_DVBT: |
| ret = cxd2820r_get_tune_settings_t(fe, s); |
| break; |
| case SYS_DVBT2: |
| ret = cxd2820r_get_tune_settings_t2(fe, s); |
| break; |
| case SYS_DVBC_ANNEX_A: |
| ret = cxd2820r_get_tune_settings_c(fe, s); |
| break; |
| default: |
| ret = -EINVAL; |
| break; |
| } |
| return ret; |
| } |
| |
| static enum dvbfe_search cxd2820r_search(struct dvb_frontend *fe) |
| { |
| struct cxd2820r_priv *priv = fe->demodulator_priv; |
| struct i2c_client *client = priv->client[0]; |
| struct dtv_frontend_properties *c = &fe->dtv_property_cache; |
| int ret, i; |
| enum fe_status status = 0; |
| |
| dev_dbg(&client->dev, "delivery_system=%d\n", c->delivery_system); |
| |
| /* switch between DVB-T and DVB-T2 when tune fails */ |
| if (priv->last_tune_failed) { |
| if (priv->delivery_system == SYS_DVBT) { |
| ret = cxd2820r_sleep_t(fe); |
| if (ret) |
| goto error; |
| |
| c->delivery_system = SYS_DVBT2; |
| } else if (priv->delivery_system == SYS_DVBT2) { |
| ret = cxd2820r_sleep_t2(fe); |
| if (ret) |
| goto error; |
| |
| c->delivery_system = SYS_DVBT; |
| } |
| } |
| |
| /* set frontend */ |
| ret = cxd2820r_set_frontend(fe); |
| if (ret) |
| goto error; |
| |
| /* frontend lock wait loop count */ |
| switch (priv->delivery_system) { |
| case SYS_DVBT: |
| case SYS_DVBC_ANNEX_A: |
| i = 20; |
| break; |
| case SYS_DVBT2: |
| i = 40; |
| break; |
| case SYS_UNDEFINED: |
| default: |
| i = 0; |
| break; |
| } |
| |
| /* wait frontend lock */ |
| for (; i > 0; i--) { |
| dev_dbg(&client->dev, "loop=%d\n", i); |
| msleep(50); |
| ret = cxd2820r_read_status(fe, &status); |
| if (ret) |
| goto error; |
| |
| if (status & FE_HAS_LOCK) |
| break; |
| } |
| |
| /* check if we have a valid signal */ |
| if (status & FE_HAS_LOCK) { |
| priv->last_tune_failed = false; |
| return DVBFE_ALGO_SEARCH_SUCCESS; |
| } else { |
| priv->last_tune_failed = true; |
| return DVBFE_ALGO_SEARCH_AGAIN; |
| } |
| |
| error: |
| dev_dbg(&client->dev, "failed=%d\n", ret); |
| return DVBFE_ALGO_SEARCH_ERROR; |
| } |
| |
| static enum dvbfe_algo cxd2820r_get_frontend_algo(struct dvb_frontend *fe) |
| { |
| return DVBFE_ALGO_CUSTOM; |
| } |
| |
| static void cxd2820r_release(struct dvb_frontend *fe) |
| { |
| struct cxd2820r_priv *priv = fe->demodulator_priv; |
| struct i2c_client *client = priv->client[0]; |
| |
| dev_dbg(&client->dev, "\n"); |
| |
| i2c_unregister_device(client); |
| |
| return; |
| } |
| |
| static int cxd2820r_i2c_gate_ctrl(struct dvb_frontend *fe, int enable) |
| { |
| struct cxd2820r_priv *priv = fe->demodulator_priv; |
| struct i2c_client *client = priv->client[0]; |
| |
| dev_dbg_ratelimited(&client->dev, "enable=%d\n", enable); |
| |
| return regmap_update_bits(priv->regmap[0], 0x00db, 0x01, enable ? 1 : 0); |
| } |
| |
| #ifdef CONFIG_GPIOLIB |
| static int cxd2820r_gpio_direction_output(struct gpio_chip *chip, unsigned nr, |
| int val) |
| { |
| struct cxd2820r_priv *priv = gpiochip_get_data(chip); |
| struct i2c_client *client = priv->client[0]; |
| u8 gpio[GPIO_COUNT]; |
| |
| dev_dbg(&client->dev, "nr=%u val=%d\n", nr, val); |
| |
| memcpy(gpio, priv->gpio, sizeof(gpio)); |
| gpio[nr] = CXD2820R_GPIO_E | CXD2820R_GPIO_O | (val << 2); |
| |
| return cxd2820r_gpio(&priv->fe, gpio); |
| } |
| |
| static void cxd2820r_gpio_set(struct gpio_chip *chip, unsigned nr, int val) |
| { |
| struct cxd2820r_priv *priv = gpiochip_get_data(chip); |
| struct i2c_client *client = priv->client[0]; |
| u8 gpio[GPIO_COUNT]; |
| |
| dev_dbg(&client->dev, "nr=%u val=%d\n", nr, val); |
| |
| memcpy(gpio, priv->gpio, sizeof(gpio)); |
| gpio[nr] = CXD2820R_GPIO_E | CXD2820R_GPIO_O | (val << 2); |
| |
| (void) cxd2820r_gpio(&priv->fe, gpio); |
| |
| return; |
| } |
| |
| static int cxd2820r_gpio_get(struct gpio_chip *chip, unsigned nr) |
| { |
| struct cxd2820r_priv *priv = gpiochip_get_data(chip); |
| struct i2c_client *client = priv->client[0]; |
| |
| dev_dbg(&client->dev, "nr=%u\n", nr); |
| |
| return (priv->gpio[nr] >> 2) & 0x01; |
| } |
| #endif |
| |
| static const struct dvb_frontend_ops cxd2820r_ops = { |
| .delsys = { SYS_DVBT, SYS_DVBT2, SYS_DVBC_ANNEX_A }, |
| /* default: DVB-T/T2 */ |
| .info = { |
| .name = "Sony CXD2820R", |
| |
| .caps = FE_CAN_FEC_1_2 | |
| FE_CAN_FEC_2_3 | |
| FE_CAN_FEC_3_4 | |
| FE_CAN_FEC_5_6 | |
| FE_CAN_FEC_7_8 | |
| FE_CAN_FEC_AUTO | |
| FE_CAN_QPSK | |
| FE_CAN_QAM_16 | |
| FE_CAN_QAM_32 | |
| FE_CAN_QAM_64 | |
| FE_CAN_QAM_128 | |
| FE_CAN_QAM_256 | |
| FE_CAN_QAM_AUTO | |
| FE_CAN_TRANSMISSION_MODE_AUTO | |
| FE_CAN_GUARD_INTERVAL_AUTO | |
| FE_CAN_HIERARCHY_AUTO | |
| FE_CAN_MUTE_TS | |
| FE_CAN_2G_MODULATION | |
| FE_CAN_MULTISTREAM |
| }, |
| |
| .release = cxd2820r_release, |
| .init = cxd2820r_init, |
| .sleep = cxd2820r_sleep, |
| |
| .get_tune_settings = cxd2820r_get_tune_settings, |
| .i2c_gate_ctrl = cxd2820r_i2c_gate_ctrl, |
| |
| .get_frontend = cxd2820r_get_frontend, |
| |
| .get_frontend_algo = cxd2820r_get_frontend_algo, |
| .search = cxd2820r_search, |
| |
| .read_status = cxd2820r_read_status, |
| .read_snr = cxd2820r_read_snr, |
| .read_ber = cxd2820r_read_ber, |
| .read_ucblocks = cxd2820r_read_ucblocks, |
| .read_signal_strength = cxd2820r_read_signal_strength, |
| }; |
| |
| /* |
| * XXX: That is wrapper to cxd2820r_probe() via driver core in order to provide |
| * proper I2C client for legacy media attach binding. |
| * New users must use I2C client binding directly! |
| */ |
| struct dvb_frontend *cxd2820r_attach(const struct cxd2820r_config *config, |
| struct i2c_adapter *adapter, |
| int *gpio_chip_base) |
| { |
| struct i2c_client *client; |
| struct i2c_board_info board_info; |
| struct cxd2820r_platform_data pdata; |
| |
| pdata.ts_mode = config->ts_mode; |
| pdata.ts_clk_inv = config->ts_clock_inv; |
| pdata.if_agc_polarity = config->if_agc_polarity; |
| pdata.spec_inv = config->spec_inv; |
| pdata.gpio_chip_base = &gpio_chip_base; |
| pdata.attach_in_use = true; |
| |
| memset(&board_info, 0, sizeof(board_info)); |
| strscpy(board_info.type, "cxd2820r", I2C_NAME_SIZE); |
| board_info.addr = config->i2c_address; |
| board_info.platform_data = &pdata; |
| client = i2c_new_client_device(adapter, &board_info); |
| if (!i2c_client_has_driver(client)) |
| return NULL; |
| |
| return pdata.get_dvb_frontend(client); |
| } |
| EXPORT_SYMBOL(cxd2820r_attach); |
| |
| static struct dvb_frontend *cxd2820r_get_dvb_frontend(struct i2c_client *client) |
| { |
| struct cxd2820r_priv *priv = i2c_get_clientdata(client); |
| |
| dev_dbg(&client->dev, "\n"); |
| |
| return &priv->fe; |
| } |
| |
| static int cxd2820r_probe(struct i2c_client *client, |
| const struct i2c_device_id *id) |
| { |
| struct cxd2820r_platform_data *pdata = client->dev.platform_data; |
| struct cxd2820r_priv *priv; |
| int ret, *gpio_chip_base; |
| unsigned int utmp; |
| static const struct regmap_range_cfg regmap_range_cfg0[] = { |
| { |
| .range_min = 0x0000, |
| .range_max = 0x3fff, |
| .selector_reg = 0x00, |
| .selector_mask = 0xff, |
| .selector_shift = 0, |
| .window_start = 0x00, |
| .window_len = 0x100, |
| }, |
| }; |
| static const struct regmap_range_cfg regmap_range_cfg1[] = { |
| { |
| .range_min = 0x0000, |
| .range_max = 0x01ff, |
| .selector_reg = 0x00, |
| .selector_mask = 0xff, |
| .selector_shift = 0, |
| .window_start = 0x00, |
| .window_len = 0x100, |
| }, |
| }; |
| static const struct regmap_config regmap_config0 = { |
| .reg_bits = 8, |
| .val_bits = 8, |
| .max_register = 0x3fff, |
| .ranges = regmap_range_cfg0, |
| .num_ranges = ARRAY_SIZE(regmap_range_cfg0), |
| .cache_type = REGCACHE_NONE, |
| }; |
| static const struct regmap_config regmap_config1 = { |
| .reg_bits = 8, |
| .val_bits = 8, |
| .max_register = 0x01ff, |
| .ranges = regmap_range_cfg1, |
| .num_ranges = ARRAY_SIZE(regmap_range_cfg1), |
| .cache_type = REGCACHE_NONE, |
| }; |
| |
| dev_dbg(&client->dev, "\n"); |
| |
| priv = kzalloc(sizeof(*priv), GFP_KERNEL); |
| if (!priv) { |
| ret = -ENOMEM; |
| goto err; |
| } |
| |
| priv->client[0] = client; |
| priv->fe.demodulator_priv = priv; |
| priv->i2c = client->adapter; |
| priv->ts_mode = pdata->ts_mode; |
| priv->ts_clk_inv = pdata->ts_clk_inv; |
| priv->if_agc_polarity = pdata->if_agc_polarity; |
| priv->spec_inv = pdata->spec_inv; |
| gpio_chip_base = *pdata->gpio_chip_base; |
| priv->regmap[0] = regmap_init_i2c(priv->client[0], ®map_config0); |
| if (IS_ERR(priv->regmap[0])) { |
| ret = PTR_ERR(priv->regmap[0]); |
| goto err_kfree; |
| } |
| |
| /* Check demod answers with correct chip id */ |
| ret = regmap_read(priv->regmap[0], 0x00fd, &utmp); |
| if (ret) |
| goto err_regmap_0_regmap_exit; |
| |
| dev_dbg(&client->dev, "chip_id=%02x\n", utmp); |
| |
| if (utmp != 0xe1) { |
| ret = -ENODEV; |
| goto err_regmap_0_regmap_exit; |
| } |
| |
| /* |
| * Chip has two I2C addresses for different register banks. We register |
| * one dummy I2C client in in order to get own I2C client for each |
| * register bank. |
| */ |
| priv->client[1] = i2c_new_dummy_device(client->adapter, client->addr | (1 << 1)); |
| if (IS_ERR(priv->client[1])) { |
| ret = PTR_ERR(priv->client[1]); |
| dev_err(&client->dev, "I2C registration failed\n"); |
| goto err_regmap_0_regmap_exit; |
| } |
| |
| priv->regmap[1] = regmap_init_i2c(priv->client[1], ®map_config1); |
| if (IS_ERR(priv->regmap[1])) { |
| ret = PTR_ERR(priv->regmap[1]); |
| goto err_client_1_i2c_unregister_device; |
| } |
| |
| if (gpio_chip_base) { |
| #ifdef CONFIG_GPIOLIB |
| /* Add GPIOs */ |
| priv->gpio_chip.label = KBUILD_MODNAME; |
| priv->gpio_chip.parent = &client->dev; |
| priv->gpio_chip.owner = THIS_MODULE; |
| priv->gpio_chip.direction_output = cxd2820r_gpio_direction_output; |
| priv->gpio_chip.set = cxd2820r_gpio_set; |
| priv->gpio_chip.get = cxd2820r_gpio_get; |
| priv->gpio_chip.base = -1; /* Dynamic allocation */ |
| priv->gpio_chip.ngpio = GPIO_COUNT; |
| priv->gpio_chip.can_sleep = 1; |
| ret = gpiochip_add_data(&priv->gpio_chip, priv); |
| if (ret) |
| goto err_regmap_1_regmap_exit; |
| |
| dev_dbg(&client->dev, "gpio_chip.base=%d\n", |
| priv->gpio_chip.base); |
| |
| *gpio_chip_base = priv->gpio_chip.base; |
| #else |
| /* |
| * Use static GPIO configuration if GPIOLIB is undefined. |
| * This is fallback condition. |
| */ |
| u8 gpio[GPIO_COUNT]; |
| gpio[0] = (*gpio_chip_base >> 0) & 0x07; |
| gpio[1] = (*gpio_chip_base >> 3) & 0x07; |
| gpio[2] = 0; |
| ret = cxd2820r_gpio(&priv->fe, gpio); |
| if (ret) |
| goto err_regmap_1_regmap_exit; |
| #endif |
| } |
| |
| /* Create dvb frontend */ |
| memcpy(&priv->fe.ops, &cxd2820r_ops, sizeof(priv->fe.ops)); |
| if (!pdata->attach_in_use) |
| priv->fe.ops.release = NULL; |
| i2c_set_clientdata(client, priv); |
| |
| /* Setup callbacks */ |
| pdata->get_dvb_frontend = cxd2820r_get_dvb_frontend; |
| |
| dev_info(&client->dev, "Sony CXD2820R successfully identified\n"); |
| |
| return 0; |
| err_regmap_1_regmap_exit: |
| regmap_exit(priv->regmap[1]); |
| err_client_1_i2c_unregister_device: |
| i2c_unregister_device(priv->client[1]); |
| err_regmap_0_regmap_exit: |
| regmap_exit(priv->regmap[0]); |
| err_kfree: |
| kfree(priv); |
| err: |
| dev_dbg(&client->dev, "failed=%d\n", ret); |
| return ret; |
| } |
| |
| static int cxd2820r_remove(struct i2c_client *client) |
| { |
| struct cxd2820r_priv *priv = i2c_get_clientdata(client); |
| |
| dev_dbg(&client->dev, "\n"); |
| |
| #ifdef CONFIG_GPIOLIB |
| if (priv->gpio_chip.label) |
| gpiochip_remove(&priv->gpio_chip); |
| #endif |
| regmap_exit(priv->regmap[1]); |
| i2c_unregister_device(priv->client[1]); |
| |
| regmap_exit(priv->regmap[0]); |
| |
| kfree(priv); |
| |
| return 0; |
| } |
| |
| static const struct i2c_device_id cxd2820r_id_table[] = { |
| {"cxd2820r", 0}, |
| {} |
| }; |
| MODULE_DEVICE_TABLE(i2c, cxd2820r_id_table); |
| |
| static struct i2c_driver cxd2820r_driver = { |
| .driver = { |
| .name = "cxd2820r", |
| .suppress_bind_attrs = true, |
| }, |
| .probe = cxd2820r_probe, |
| .remove = cxd2820r_remove, |
| .id_table = cxd2820r_id_table, |
| }; |
| |
| module_i2c_driver(cxd2820r_driver); |
| |
| MODULE_AUTHOR("Antti Palosaari <crope@iki.fi>"); |
| MODULE_DESCRIPTION("Sony CXD2820R demodulator driver"); |
| MODULE_LICENSE("GPL"); |