| /* |
| * Device Tree Source for the Lager board |
| * |
| * Copyright (C) 2013-2014 Renesas Solutions Corp. |
| * Copyright (C) 2014 Cogent Embedded, Inc. |
| * Copyright (C) 2015-2016 Renesas Electronics Corporation |
| * |
| * This file is licensed under the terms of the GNU General Public License |
| * version 2. This program is licensed "as is" without any warranty of any |
| * kind, whether express or implied. |
| */ |
| |
| /* |
| * SSI-AK4643 |
| * |
| * SW1: 1: AK4643 |
| * 2: CN22 |
| * 3: ADV7511 |
| * |
| * This command is required when Playback/Capture |
| * |
| * amixer set "LINEOUT Mixer DACL" on |
| * amixer set "DVC Out" 100% |
| * amixer set "DVC In" 100% |
| * |
| * You can use Mute |
| * |
| * amixer set "DVC Out Mute" on |
| * amixer set "DVC In Mute" on |
| * |
| * You can use Volume Ramp |
| * |
| * amixer set "DVC Out Ramp Up Rate" "0.125 dB/64 steps" |
| * amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps" |
| * amixer set "DVC Out Ramp" on |
| * aplay xxx.wav & |
| * amixer set "DVC Out" 80% // Volume Down |
| * amixer set "DVC Out" 100% // Volume Up |
| */ |
| |
| /dts-v1/; |
| #include "r8a7790.dtsi" |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/input/input.h> |
| |
| / { |
| model = "Lager"; |
| compatible = "renesas,lager", "renesas,r8a7790"; |
| |
| aliases { |
| serial0 = &scif0; |
| serial1 = &scifa1; |
| i2c8 = &gpioi2c1; |
| i2c10 = &i2cexio0; |
| i2c11 = &i2cexio1; |
| }; |
| |
| chosen { |
| bootargs = "ignore_loglevel rw root=/dev/nfs ip=dhcp"; |
| stdout-path = "serial0:115200n8"; |
| }; |
| |
| memory@40000000 { |
| device_type = "memory"; |
| reg = <0 0x40000000 0 0x40000000>; |
| }; |
| |
| memory@140000000 { |
| device_type = "memory"; |
| reg = <1 0x40000000 0 0xc0000000>; |
| }; |
| |
| lbsc { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| }; |
| |
| keyboard { |
| compatible = "gpio-keys"; |
| |
| one { |
| linux,code = <KEY_1>; |
| label = "SW2-1"; |
| wakeup-source; |
| debounce-interval = <20>; |
| gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; |
| }; |
| two { |
| linux,code = <KEY_2>; |
| label = "SW2-2"; |
| wakeup-source; |
| debounce-interval = <20>; |
| gpios = <&gpio1 24 GPIO_ACTIVE_LOW>; |
| }; |
| three { |
| linux,code = <KEY_3>; |
| label = "SW2-3"; |
| wakeup-source; |
| debounce-interval = <20>; |
| gpios = <&gpio1 26 GPIO_ACTIVE_LOW>; |
| }; |
| four { |
| linux,code = <KEY_4>; |
| label = "SW2-4"; |
| wakeup-source; |
| debounce-interval = <20>; |
| gpios = <&gpio1 28 GPIO_ACTIVE_LOW>; |
| }; |
| }; |
| |
| leds { |
| compatible = "gpio-leds"; |
| led6 { |
| gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>; |
| }; |
| led7 { |
| gpios = <&gpio4 23 GPIO_ACTIVE_HIGH>; |
| }; |
| led8 { |
| gpios = <&gpio5 17 GPIO_ACTIVE_HIGH>; |
| }; |
| }; |
| |
| fixedregulator3v3: regulator-3v3 { |
| compatible = "regulator-fixed"; |
| regulator-name = "fixed-3.3V"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| vcc_sdhi0: regulator-vcc-sdhi0 { |
| compatible = "regulator-fixed"; |
| |
| regulator-name = "SDHI0 Vcc"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| |
| gpio = <&gpio5 24 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| |
| vccq_sdhi0: regulator-vccq-sdhi0 { |
| compatible = "regulator-gpio"; |
| |
| regulator-name = "SDHI0 VccQ"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3300000>; |
| |
| gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>; |
| gpios-states = <1>; |
| states = <3300000 1 |
| 1800000 0>; |
| }; |
| |
| vcc_sdhi2: regulator-vcc-sdhi2 { |
| compatible = "regulator-fixed"; |
| |
| regulator-name = "SDHI2 Vcc"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| |
| gpio = <&gpio5 25 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| |
| vccq_sdhi2: regulator-vccq-sdhi2 { |
| compatible = "regulator-gpio"; |
| |
| regulator-name = "SDHI2 VccQ"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3300000>; |
| |
| gpios = <&gpio5 30 GPIO_ACTIVE_HIGH>; |
| gpios-states = <1>; |
| states = <3300000 1 |
| 1800000 0>; |
| }; |
| |
| audio_clock: audio_clock { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <11289600>; |
| }; |
| |
| rsnd_ak4643: sound { |
| compatible = "simple-audio-card"; |
| |
| simple-audio-card,format = "left_j"; |
| simple-audio-card,bitclock-master = <&sndcodec>; |
| simple-audio-card,frame-master = <&sndcodec>; |
| |
| sndcpu: simple-audio-card,cpu { |
| sound-dai = <&rcar_sound>; |
| }; |
| |
| sndcodec: simple-audio-card,codec { |
| sound-dai = <&ak4643>; |
| clocks = <&audio_clock>; |
| }; |
| }; |
| |
| vga-encoder { |
| compatible = "adi,adv7123"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| adv7123_in: endpoint { |
| remote-endpoint = <&du_out_rgb>; |
| }; |
| }; |
| port@1 { |
| reg = <1>; |
| adv7123_out: endpoint { |
| remote-endpoint = <&vga_in>; |
| }; |
| }; |
| }; |
| }; |
| |
| vga { |
| compatible = "vga-connector"; |
| |
| port { |
| vga_in: endpoint { |
| remote-endpoint = <&adv7123_out>; |
| }; |
| }; |
| }; |
| |
| hdmi-in { |
| compatible = "hdmi-connector"; |
| type = "a"; |
| |
| port { |
| hdmi_con_in: endpoint { |
| remote-endpoint = <&adv7612_in>; |
| }; |
| }; |
| }; |
| |
| hdmi-out { |
| compatible = "hdmi-connector"; |
| type = "a"; |
| |
| port { |
| hdmi_con_out: endpoint { |
| remote-endpoint = <&adv7511_out>; |
| }; |
| }; |
| }; |
| |
| x2_clk: x2-clock { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <148500000>; |
| }; |
| |
| x13_clk: x13-clock { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <148500000>; |
| }; |
| |
| gpioi2c1: i2c-8 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "i2c-gpio"; |
| status = "disabled"; |
| gpios = <&gpio1 17 GPIO_ACTIVE_HIGH /* sda */ |
| &gpio1 16 GPIO_ACTIVE_HIGH /* scl */ |
| >; |
| i2c-gpio,delay-us = <5>; |
| }; |
| |
| /* |
| * IIC0/I2C0 is routed to EXIO connector A, pins 114 (SCL) + 116 (SDA) only. |
| * We use the I2C demuxer, so the desired IP core can be selected at runtime |
| * depending on the use case (e.g. DMA with IIC0 or slave support with I2C0). |
| * Note: For testing the I2C slave feature, it is convenient to connect this |
| * bus with IIC3 on pins 110 (SCL) + 112 (SDA), select I2C0 at runtime, and |
| * instantiate the slave device at runtime according to the documentation. |
| * You can then communicate with the slave via IIC3. |
| * |
| * IIC0/I2C0 does not appear to support fallback to GPIO. |
| */ |
| i2cexio0: i2c-10 { |
| compatible = "i2c-demux-pinctrl"; |
| i2c-parent = <&iic0>, <&i2c0>; |
| i2c-bus-name = "i2c-exio0"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| |
| /* |
| * IIC1/I2C1 is routed to EXIO connector A, pins 78 (SCL) + 80 (SDA). |
| * This is similar to the arangement described for i2cexio0 (above) |
| * with a fallback to GPIO also provided. |
| */ |
| i2cexio1: i2c-11 { |
| compatible = "i2c-demux-pinctrl"; |
| i2c-parent = <&iic1>, <&i2c1>, <&gpioi2c1>; |
| i2c-bus-name = "i2c-exio1"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| }; |
| |
| &du { |
| pinctrl-0 = <&du_pins>; |
| pinctrl-names = "default"; |
| status = "okay"; |
| |
| clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>, <&cpg CPG_MOD 722>, |
| <&cpg CPG_MOD 726>, <&cpg CPG_MOD 725>, |
| <&x13_clk>, <&x2_clk>; |
| clock-names = "du.0", "du.1", "du.2", "lvds.0", "lvds.1", |
| "dclkin.0", "dclkin.1"; |
| |
| ports { |
| port@0 { |
| endpoint { |
| remote-endpoint = <&adv7123_in>; |
| }; |
| }; |
| port@1 { |
| endpoint { |
| remote-endpoint = <&adv7511_in>; |
| }; |
| }; |
| port@2 { |
| lvds_connector: endpoint { |
| }; |
| }; |
| }; |
| }; |
| |
| &extal_clk { |
| clock-frequency = <20000000>; |
| }; |
| |
| &pfc { |
| pinctrl-0 = <&scif_clk_pins>; |
| pinctrl-names = "default"; |
| |
| du_pins: du { |
| groups = "du_rgb666", "du_sync_1", "du_clk_out_0"; |
| function = "du"; |
| }; |
| |
| scif0_pins: scif0 { |
| groups = "scif0_data"; |
| function = "scif0"; |
| }; |
| |
| scif_clk_pins: scif_clk { |
| groups = "scif_clk"; |
| function = "scif_clk"; |
| }; |
| |
| ether_pins: ether { |
| groups = "eth_link", "eth_mdio", "eth_rmii"; |
| function = "eth"; |
| }; |
| |
| phy1_pins: phy1 { |
| groups = "intc_irq0"; |
| function = "intc"; |
| }; |
| |
| scifa1_pins: scifa1 { |
| groups = "scifa1_data"; |
| function = "scifa1"; |
| }; |
| |
| sdhi0_pins: sd0 { |
| groups = "sdhi0_data4", "sdhi0_ctrl"; |
| function = "sdhi0"; |
| power-source = <3300>; |
| }; |
| |
| sdhi0_pins_uhs: sd0_uhs { |
| groups = "sdhi0_data4", "sdhi0_ctrl"; |
| function = "sdhi0"; |
| power-source = <1800>; |
| }; |
| |
| sdhi2_pins: sd2 { |
| groups = "sdhi2_data4", "sdhi2_ctrl"; |
| function = "sdhi2"; |
| power-source = <3300>; |
| }; |
| |
| sdhi2_pins_uhs: sd2_uhs { |
| groups = "sdhi2_data4", "sdhi2_ctrl"; |
| function = "sdhi2"; |
| power-source = <1800>; |
| }; |
| |
| mmc1_pins: mmc1 { |
| groups = "mmc1_data8", "mmc1_ctrl"; |
| function = "mmc1"; |
| }; |
| |
| qspi_pins: qspi { |
| groups = "qspi_ctrl", "qspi_data4"; |
| function = "qspi"; |
| }; |
| |
| msiof1_pins: msiof1 { |
| groups = "msiof1_clk", "msiof1_sync", "msiof1_rx", |
| "msiof1_tx"; |
| function = "msiof1"; |
| }; |
| |
| i2c0_pins: i2c0 { |
| groups = "i2c0"; |
| function = "i2c0"; |
| }; |
| |
| iic0_pins: iic0 { |
| groups = "iic0"; |
| function = "iic0"; |
| }; |
| |
| i2c1_pins: i2c1 { |
| groups = "i2c1"; |
| function = "i2c1"; |
| }; |
| |
| iic1_pins: iic1 { |
| groups = "iic1"; |
| function = "iic1"; |
| }; |
| |
| iic2_pins: iic2 { |
| groups = "iic2"; |
| function = "iic2"; |
| }; |
| |
| iic3_pins: iic3 { |
| groups = "iic3"; |
| function = "iic3"; |
| }; |
| |
| hsusb_pins: hsusb { |
| groups = "usb0_ovc_vbus"; |
| function = "usb0"; |
| }; |
| |
| usb0_pins: usb0 { |
| groups = "usb0"; |
| function = "usb0"; |
| }; |
| |
| usb1_pins: usb1 { |
| groups = "usb1"; |
| function = "usb1"; |
| }; |
| |
| usb2_pins: usb2 { |
| groups = "usb2"; |
| function = "usb2"; |
| }; |
| |
| vin0_pins: vin0 { |
| groups = "vin0_data24", "vin0_sync", "vin0_clkenb", "vin0_clk"; |
| function = "vin0"; |
| }; |
| |
| vin1_pins: vin1 { |
| groups = "vin1_data8", "vin1_clk"; |
| function = "vin1"; |
| }; |
| |
| sound_pins: sound { |
| groups = "ssi0129_ctrl", "ssi0_data", "ssi1_data"; |
| function = "ssi"; |
| }; |
| |
| sound_clk_pins: sound_clk { |
| groups = "audio_clk_a"; |
| function = "audio_clk"; |
| }; |
| }; |
| |
| ðer { |
| pinctrl-0 = <ðer_pins &phy1_pins>; |
| pinctrl-names = "default"; |
| |
| phy-handle = <&phy1>; |
| renesas,ether-link-active-low; |
| status = "okay"; |
| |
| phy1: ethernet-phy@1 { |
| reg = <1>; |
| interrupt-parent = <&irqc0>; |
| interrupts = <0 IRQ_TYPE_LEVEL_LOW>; |
| micrel,led-mode = <1>; |
| }; |
| }; |
| |
| &cmt0 { |
| status = "okay"; |
| }; |
| |
| &mmcif1 { |
| pinctrl-0 = <&mmc1_pins>; |
| pinctrl-names = "default"; |
| |
| vmmc-supply = <&fixedregulator3v3>; |
| bus-width = <8>; |
| non-removable; |
| status = "okay"; |
| }; |
| |
| &sata1 { |
| status = "okay"; |
| }; |
| |
| &qspi { |
| pinctrl-0 = <&qspi_pins>; |
| pinctrl-names = "default"; |
| |
| status = "okay"; |
| |
| flash: flash@0 { |
| compatible = "spansion,s25fl512s", "jedec,spi-nor"; |
| reg = <0>; |
| spi-max-frequency = <30000000>; |
| spi-tx-bus-width = <4>; |
| spi-rx-bus-width = <4>; |
| spi-cpha; |
| spi-cpol; |
| m25p,fast-read; |
| |
| partitions { |
| compatible = "fixed-partitions"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| partition@0 { |
| label = "loader"; |
| reg = <0x00000000 0x00040000>; |
| read-only; |
| }; |
| partition@40000 { |
| label = "user"; |
| reg = <0x00040000 0x00400000>; |
| read-only; |
| }; |
| partition@440000 { |
| label = "flash"; |
| reg = <0x00440000 0x03bc0000>; |
| }; |
| }; |
| }; |
| }; |
| |
| &scif0 { |
| pinctrl-0 = <&scif0_pins>; |
| pinctrl-names = "default"; |
| |
| status = "okay"; |
| }; |
| |
| &scifa1 { |
| pinctrl-0 = <&scifa1_pins>; |
| pinctrl-names = "default"; |
| |
| status = "okay"; |
| }; |
| |
| &scif_clk { |
| clock-frequency = <14745600>; |
| }; |
| |
| &msiof1 { |
| pinctrl-0 = <&msiof1_pins>; |
| pinctrl-names = "default"; |
| |
| status = "okay"; |
| |
| pmic: pmic@0 { |
| compatible = "renesas,r2a11302ft"; |
| reg = <0>; |
| spi-max-frequency = <6000000>; |
| spi-cpol; |
| spi-cpha; |
| }; |
| }; |
| |
| &sdhi0 { |
| pinctrl-0 = <&sdhi0_pins>; |
| pinctrl-1 = <&sdhi0_pins_uhs>; |
| pinctrl-names = "default", "state_uhs"; |
| |
| vmmc-supply = <&vcc_sdhi0>; |
| vqmmc-supply = <&vccq_sdhi0>; |
| cd-gpios = <&gpio3 6 GPIO_ACTIVE_LOW>; |
| sd-uhs-sdr50; |
| sd-uhs-sdr104; |
| status = "okay"; |
| }; |
| |
| &sdhi2 { |
| pinctrl-0 = <&sdhi2_pins>; |
| pinctrl-1 = <&sdhi2_pins_uhs>; |
| pinctrl-names = "default", "state_uhs"; |
| |
| vmmc-supply = <&vcc_sdhi2>; |
| vqmmc-supply = <&vccq_sdhi2>; |
| cd-gpios = <&gpio3 22 GPIO_ACTIVE_LOW>; |
| sd-uhs-sdr50; |
| status = "okay"; |
| }; |
| |
| &cpu0 { |
| cpu0-supply = <&vdd_dvfs>; |
| }; |
| |
| &i2c0 { |
| pinctrl-0 = <&i2c0_pins>; |
| pinctrl-names = "i2c-exio0"; |
| }; |
| |
| &iic0 { |
| pinctrl-0 = <&iic0_pins>; |
| pinctrl-names = "i2c-exio0"; |
| }; |
| |
| &i2c1 { |
| pinctrl-0 = <&i2c1_pins>; |
| pinctrl-names = "i2c-exio1"; |
| }; |
| |
| &iic1 { |
| pinctrl-0 = <&iic1_pins>; |
| pinctrl-names = "i2c-exio1"; |
| }; |
| |
| &iic2 { |
| status = "okay"; |
| pinctrl-0 = <&iic2_pins>; |
| pinctrl-names = "default"; |
| |
| clock-frequency = <100000>; |
| |
| ak4643: codec@12 { |
| compatible = "asahi-kasei,ak4643"; |
| #sound-dai-cells = <0>; |
| reg = <0x12>; |
| }; |
| |
| composite-in@20 { |
| compatible = "adi,adv7180"; |
| reg = <0x20>; |
| remote = <&vin1>; |
| |
| port { |
| adv7180: endpoint { |
| bus-width = <8>; |
| remote-endpoint = <&vin1ep0>; |
| }; |
| }; |
| }; |
| |
| hdmi@39 { |
| compatible = "adi,adv7511w"; |
| reg = <0x39>; |
| interrupt-parent = <&gpio1>; |
| interrupts = <15 IRQ_TYPE_LEVEL_LOW>; |
| |
| adi,input-depth = <8>; |
| adi,input-colorspace = "rgb"; |
| adi,input-clock = "1x"; |
| adi,input-style = <1>; |
| adi,input-justification = "evenly"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| adv7511_in: endpoint { |
| remote-endpoint = <&du_out_lvds0>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| adv7511_out: endpoint { |
| remote-endpoint = <&hdmi_con_out>; |
| }; |
| }; |
| }; |
| }; |
| |
| hdmi-in@4c { |
| compatible = "adi,adv7612"; |
| reg = <0x4c>; |
| interrupt-parent = <&gpio1>; |
| interrupts = <20 IRQ_TYPE_LEVEL_LOW>; |
| default-input = <0>; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| adv7612_in: endpoint { |
| remote-endpoint = <&hdmi_con_in>; |
| }; |
| }; |
| |
| port@2 { |
| reg = <2>; |
| adv7612_out: endpoint { |
| remote-endpoint = <&vin0ep2>; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| &iic3 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&iic3_pins>; |
| status = "okay"; |
| |
| pmic@58 { |
| compatible = "dlg,da9063"; |
| reg = <0x58>; |
| interrupt-parent = <&irqc0>; |
| interrupts = <2 IRQ_TYPE_LEVEL_LOW>; |
| interrupt-controller; |
| |
| rtc { |
| compatible = "dlg,da9063-rtc"; |
| }; |
| |
| wdt { |
| compatible = "dlg,da9063-watchdog"; |
| }; |
| }; |
| |
| vdd_dvfs: regulator@68 { |
| compatible = "dlg,da9210"; |
| reg = <0x68>; |
| interrupt-parent = <&irqc0>; |
| interrupts = <2 IRQ_TYPE_LEVEL_LOW>; |
| |
| regulator-min-microvolt = <1000000>; |
| regulator-max-microvolt = <1000000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| }; |
| |
| &pci0 { |
| status = "okay"; |
| pinctrl-0 = <&usb0_pins>; |
| pinctrl-names = "default"; |
| }; |
| |
| &pci1 { |
| status = "okay"; |
| pinctrl-0 = <&usb1_pins>; |
| pinctrl-names = "default"; |
| }; |
| |
| &xhci { |
| status = "okay"; |
| pinctrl-0 = <&usb2_pins>; |
| pinctrl-names = "default"; |
| }; |
| |
| &pci2 { |
| status = "okay"; |
| pinctrl-0 = <&usb2_pins>; |
| pinctrl-names = "default"; |
| }; |
| |
| &hsusb { |
| status = "okay"; |
| pinctrl-0 = <&hsusb_pins>; |
| pinctrl-names = "default"; |
| renesas,enable-gpio = <&gpio5 18 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| &usbphy { |
| status = "okay"; |
| }; |
| |
| /* HDMI video input */ |
| &vin0 { |
| pinctrl-0 = <&vin0_pins>; |
| pinctrl-names = "default"; |
| |
| status = "okay"; |
| |
| port { |
| vin0ep2: endpoint { |
| remote-endpoint = <&adv7612_out>; |
| bus-width = <24>; |
| hsync-active = <0>; |
| vsync-active = <0>; |
| pclk-sample = <1>; |
| data-active = <1>; |
| }; |
| }; |
| }; |
| |
| /* composite video input */ |
| &vin1 { |
| pinctrl-0 = <&vin1_pins>; |
| pinctrl-names = "default"; |
| |
| status = "okay"; |
| |
| port { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| vin1ep0: endpoint { |
| remote-endpoint = <&adv7180>; |
| bus-width = <8>; |
| }; |
| }; |
| }; |
| |
| &rcar_sound { |
| pinctrl-0 = <&sound_pins &sound_clk_pins>; |
| pinctrl-names = "default"; |
| |
| /* Single DAI */ |
| #sound-dai-cells = <0>; |
| |
| status = "okay"; |
| |
| rcar_sound,dai { |
| dai0 { |
| playback = <&ssi0 &src2 &dvc0>; |
| capture = <&ssi1 &src3 &dvc1>; |
| }; |
| }; |
| }; |
| |
| &ssi1 { |
| shared-pin; |
| }; |
