|  | /* | 
|  | * AD7879/AD7889 based touchscreen and GPIO driver | 
|  | * | 
|  | * Copyright (C) 2008-2010 Michael Hennerich, Analog Devices Inc. | 
|  | * | 
|  | * Licensed under the GPL-2 or later. | 
|  | * | 
|  | * History: | 
|  | * Copyright (c) 2005 David Brownell | 
|  | * Copyright (c) 2006 Nokia Corporation | 
|  | * Various changes: Imre Deak <imre.deak@nokia.com> | 
|  | * | 
|  | * Using code from: | 
|  | *  - corgi_ts.c | 
|  | *	Copyright (C) 2004-2005 Richard Purdie | 
|  | *  - omap_ts.[hc], ads7846.h, ts_osk.c | 
|  | *	Copyright (C) 2002 MontaVista Software | 
|  | *	Copyright (C) 2004 Texas Instruments | 
|  | *	Copyright (C) 2005 Dirk Behme | 
|  | *  - ad7877.c | 
|  | *	Copyright (C) 2006-2008 Analog Devices Inc. | 
|  | */ | 
|  |  | 
|  | #include <linux/device.h> | 
|  | #include <linux/init.h> | 
|  | #include <linux/delay.h> | 
|  | #include <linux/input.h> | 
|  | #include <linux/interrupt.h> | 
|  | #include <linux/irq.h> | 
|  | #include <linux/slab.h> | 
|  | #include <linux/spi/spi.h> | 
|  | #include <linux/i2c.h> | 
|  | #include <linux/gpio.h> | 
|  |  | 
|  | #include <linux/spi/ad7879.h> | 
|  | #include "ad7879.h" | 
|  |  | 
|  | #define AD7879_REG_ZEROS		0 | 
|  | #define AD7879_REG_CTRL1		1 | 
|  | #define AD7879_REG_CTRL2		2 | 
|  | #define AD7879_REG_CTRL3		3 | 
|  | #define AD7879_REG_AUX1HIGH		4 | 
|  | #define AD7879_REG_AUX1LOW		5 | 
|  | #define AD7879_REG_TEMP1HIGH		6 | 
|  | #define AD7879_REG_TEMP1LOW		7 | 
|  | #define AD7879_REG_XPLUS		8 | 
|  | #define AD7879_REG_YPLUS		9 | 
|  | #define AD7879_REG_Z1			10 | 
|  | #define AD7879_REG_Z2			11 | 
|  | #define AD7879_REG_AUXVBAT		12 | 
|  | #define AD7879_REG_TEMP			13 | 
|  | #define AD7879_REG_REVID		14 | 
|  |  | 
|  | /* Control REG 1 */ | 
|  | #define AD7879_TMR(x)			((x & 0xFF) << 0) | 
|  | #define AD7879_ACQ(x)			((x & 0x3) << 8) | 
|  | #define AD7879_MODE_NOC			(0 << 10)	/* Do not convert */ | 
|  | #define AD7879_MODE_SCC			(1 << 10)	/* Single channel conversion */ | 
|  | #define AD7879_MODE_SEQ0		(2 << 10)	/* Sequence 0 in Slave Mode */ | 
|  | #define AD7879_MODE_SEQ1		(3 << 10)	/* Sequence 1 in Master Mode */ | 
|  | #define AD7879_MODE_INT			(1 << 15)	/* PENIRQ disabled INT enabled */ | 
|  |  | 
|  | /* Control REG 2 */ | 
|  | #define AD7879_FCD(x)			((x & 0x3) << 0) | 
|  | #define AD7879_RESET			(1 << 4) | 
|  | #define AD7879_MFS(x)			((x & 0x3) << 5) | 
|  | #define AD7879_AVG(x)			((x & 0x3) << 7) | 
|  | #define	AD7879_SER			(1 << 9)	/* non-differential */ | 
|  | #define	AD7879_DFR			(0 << 9)	/* differential */ | 
|  | #define AD7879_GPIOPOL			(1 << 10) | 
|  | #define AD7879_GPIODIR			(1 << 11) | 
|  | #define AD7879_GPIO_DATA		(1 << 12) | 
|  | #define AD7879_GPIO_EN			(1 << 13) | 
|  | #define AD7879_PM(x)			((x & 0x3) << 14) | 
|  | #define AD7879_PM_SHUTDOWN		(0) | 
|  | #define AD7879_PM_DYN			(1) | 
|  | #define AD7879_PM_FULLON		(2) | 
|  |  | 
|  | /* Control REG 3 */ | 
|  | #define AD7879_TEMPMASK_BIT		(1<<15) | 
|  | #define AD7879_AUXVBATMASK_BIT		(1<<14) | 
|  | #define AD7879_INTMODE_BIT		(1<<13) | 
|  | #define AD7879_GPIOALERTMASK_BIT	(1<<12) | 
|  | #define AD7879_AUXLOW_BIT		(1<<11) | 
|  | #define AD7879_AUXHIGH_BIT		(1<<10) | 
|  | #define AD7879_TEMPLOW_BIT		(1<<9) | 
|  | #define AD7879_TEMPHIGH_BIT		(1<<8) | 
|  | #define AD7879_YPLUS_BIT		(1<<7) | 
|  | #define AD7879_XPLUS_BIT		(1<<6) | 
|  | #define AD7879_Z1_BIT			(1<<5) | 
|  | #define AD7879_Z2_BIT			(1<<4) | 
|  | #define AD7879_AUX_BIT			(1<<3) | 
|  | #define AD7879_VBAT_BIT			(1<<2) | 
|  | #define AD7879_TEMP_BIT			(1<<1) | 
|  |  | 
|  | enum { | 
|  | AD7879_SEQ_XPOS  = 0, | 
|  | AD7879_SEQ_YPOS  = 1, | 
|  | AD7879_SEQ_Z1    = 2, | 
|  | AD7879_SEQ_Z2    = 3, | 
|  | AD7879_NR_SENSE  = 4, | 
|  | }; | 
|  |  | 
|  | #define	MAX_12BIT			((1<<12)-1) | 
|  | #define	TS_PEN_UP_TIMEOUT		msecs_to_jiffies(50) | 
|  |  | 
|  | struct ad7879 { | 
|  | const struct ad7879_bus_ops *bops; | 
|  |  | 
|  | struct device		*dev; | 
|  | struct input_dev	*input; | 
|  | struct timer_list	timer; | 
|  | #ifdef CONFIG_GPIOLIB | 
|  | struct gpio_chip	gc; | 
|  | struct mutex		mutex; | 
|  | #endif | 
|  | unsigned int		irq; | 
|  | bool			disabled;	/* P: input->mutex */ | 
|  | bool			suspended;	/* P: input->mutex */ | 
|  | u16			conversion_data[AD7879_NR_SENSE]; | 
|  | char			phys[32]; | 
|  | u8			first_conversion_delay; | 
|  | u8			acquisition_time; | 
|  | u8			averaging; | 
|  | u8			pen_down_acc_interval; | 
|  | u8			median; | 
|  | u16			x_plate_ohms; | 
|  | u16			pressure_max; | 
|  | u16			cmd_crtl1; | 
|  | u16			cmd_crtl2; | 
|  | u16			cmd_crtl3; | 
|  | }; | 
|  |  | 
|  | static int ad7879_read(struct ad7879 *ts, u8 reg) | 
|  | { | 
|  | return ts->bops->read(ts->dev, reg); | 
|  | } | 
|  |  | 
|  | static int ad7879_multi_read(struct ad7879 *ts, u8 first_reg, u8 count, u16 *buf) | 
|  | { | 
|  | return ts->bops->multi_read(ts->dev, first_reg, count, buf); | 
|  | } | 
|  |  | 
|  | static int ad7879_write(struct ad7879 *ts, u8 reg, u16 val) | 
|  | { | 
|  | return ts->bops->write(ts->dev, reg, val); | 
|  | } | 
|  |  | 
|  | static int ad7879_report(struct ad7879 *ts) | 
|  | { | 
|  | struct input_dev *input_dev = ts->input; | 
|  | unsigned Rt; | 
|  | u16 x, y, z1, z2; | 
|  |  | 
|  | x = ts->conversion_data[AD7879_SEQ_XPOS] & MAX_12BIT; | 
|  | y = ts->conversion_data[AD7879_SEQ_YPOS] & MAX_12BIT; | 
|  | z1 = ts->conversion_data[AD7879_SEQ_Z1] & MAX_12BIT; | 
|  | z2 = ts->conversion_data[AD7879_SEQ_Z2] & MAX_12BIT; | 
|  |  | 
|  | /* | 
|  | * The samples processed here are already preprocessed by the AD7879. | 
|  | * The preprocessing function consists of a median and an averaging | 
|  | * filter.  The combination of these two techniques provides a robust | 
|  | * solution, discarding the spurious noise in the signal and keeping | 
|  | * only the data of interest.  The size of both filters is | 
|  | * programmable. (dev.platform_data, see linux/spi/ad7879.h) Other | 
|  | * user-programmable conversion controls include variable acquisition | 
|  | * time, and first conversion delay. Up to 16 averages can be taken | 
|  | * per conversion. | 
|  | */ | 
|  |  | 
|  | if (likely(x && z1)) { | 
|  | /* compute touch pressure resistance using equation #1 */ | 
|  | Rt = (z2 - z1) * x * ts->x_plate_ohms; | 
|  | Rt /= z1; | 
|  | Rt = (Rt + 2047) >> 12; | 
|  |  | 
|  | if (!timer_pending(&ts->timer)) | 
|  | input_report_key(input_dev, BTN_TOUCH, 1); | 
|  |  | 
|  | input_report_abs(input_dev, ABS_X, x); | 
|  | input_report_abs(input_dev, ABS_Y, y); | 
|  | input_report_abs(input_dev, ABS_PRESSURE, Rt); | 
|  | input_sync(input_dev); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | return -EINVAL; | 
|  | } | 
|  |  | 
|  | static void ad7879_ts_event_release(struct ad7879 *ts) | 
|  | { | 
|  | struct input_dev *input_dev = ts->input; | 
|  |  | 
|  | input_report_abs(input_dev, ABS_PRESSURE, 0); | 
|  | input_report_key(input_dev, BTN_TOUCH, 0); | 
|  | input_sync(input_dev); | 
|  | } | 
|  |  | 
|  | static void ad7879_timer(unsigned long handle) | 
|  | { | 
|  | struct ad7879 *ts = (void *)handle; | 
|  |  | 
|  | ad7879_ts_event_release(ts); | 
|  | } | 
|  |  | 
|  | static irqreturn_t ad7879_irq(int irq, void *handle) | 
|  | { | 
|  | struct ad7879 *ts = handle; | 
|  |  | 
|  | ad7879_multi_read(ts, AD7879_REG_XPLUS, AD7879_NR_SENSE, ts->conversion_data); | 
|  |  | 
|  | if (!ad7879_report(ts)) | 
|  | mod_timer(&ts->timer, jiffies + TS_PEN_UP_TIMEOUT); | 
|  |  | 
|  | return IRQ_HANDLED; | 
|  | } | 
|  |  | 
|  | static void __ad7879_enable(struct ad7879 *ts) | 
|  | { | 
|  | ad7879_write(ts, AD7879_REG_CTRL2, ts->cmd_crtl2); | 
|  | ad7879_write(ts, AD7879_REG_CTRL3, ts->cmd_crtl3); | 
|  | ad7879_write(ts, AD7879_REG_CTRL1, ts->cmd_crtl1); | 
|  |  | 
|  | enable_irq(ts->irq); | 
|  | } | 
|  |  | 
|  | static void __ad7879_disable(struct ad7879 *ts) | 
|  | { | 
|  | disable_irq(ts->irq); | 
|  |  | 
|  | if (del_timer_sync(&ts->timer)) | 
|  | ad7879_ts_event_release(ts); | 
|  |  | 
|  | ad7879_write(ts, AD7879_REG_CTRL2, AD7879_PM(AD7879_PM_SHUTDOWN)); | 
|  | } | 
|  |  | 
|  |  | 
|  | static int ad7879_open(struct input_dev *input) | 
|  | { | 
|  | struct ad7879 *ts = input_get_drvdata(input); | 
|  |  | 
|  | /* protected by input->mutex */ | 
|  | if (!ts->disabled && !ts->suspended) | 
|  | __ad7879_enable(ts); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static void ad7879_close(struct input_dev* input) | 
|  | { | 
|  | struct ad7879 *ts = input_get_drvdata(input); | 
|  |  | 
|  | /* protected by input->mutex */ | 
|  | if (!ts->disabled && !ts->suspended) | 
|  | __ad7879_disable(ts); | 
|  | } | 
|  |  | 
|  | void ad7879_suspend(struct ad7879 *ts) | 
|  | { | 
|  | mutex_lock(&ts->input->mutex); | 
|  |  | 
|  | if (!ts->suspended && !ts->disabled && ts->input->users) | 
|  | __ad7879_disable(ts); | 
|  |  | 
|  | ts->suspended = true; | 
|  |  | 
|  | mutex_unlock(&ts->input->mutex); | 
|  | } | 
|  | EXPORT_SYMBOL(ad7879_suspend); | 
|  |  | 
|  | void ad7879_resume(struct ad7879 *ts) | 
|  | { | 
|  | mutex_lock(&ts->input->mutex); | 
|  |  | 
|  | if (ts->suspended && !ts->disabled && ts->input->users) | 
|  | __ad7879_enable(ts); | 
|  |  | 
|  | ts->suspended = false; | 
|  |  | 
|  | mutex_unlock(&ts->input->mutex); | 
|  | } | 
|  | EXPORT_SYMBOL(ad7879_resume); | 
|  |  | 
|  | static void ad7879_toggle(struct ad7879 *ts, bool disable) | 
|  | { | 
|  | mutex_lock(&ts->input->mutex); | 
|  |  | 
|  | if (!ts->suspended && ts->input->users != 0) { | 
|  |  | 
|  | if (disable) { | 
|  | if (ts->disabled) | 
|  | __ad7879_enable(ts); | 
|  | } else { | 
|  | if (!ts->disabled) | 
|  | __ad7879_disable(ts); | 
|  | } | 
|  | } | 
|  |  | 
|  | ts->disabled = disable; | 
|  |  | 
|  | mutex_unlock(&ts->input->mutex); | 
|  | } | 
|  |  | 
|  | static ssize_t ad7879_disable_show(struct device *dev, | 
|  | struct device_attribute *attr, char *buf) | 
|  | { | 
|  | struct ad7879 *ts = dev_get_drvdata(dev); | 
|  |  | 
|  | return sprintf(buf, "%u\n", ts->disabled); | 
|  | } | 
|  |  | 
|  | static ssize_t ad7879_disable_store(struct device *dev, | 
|  | struct device_attribute *attr, | 
|  | const char *buf, size_t count) | 
|  | { | 
|  | struct ad7879 *ts = dev_get_drvdata(dev); | 
|  | unsigned long val; | 
|  | int error; | 
|  |  | 
|  | error = strict_strtoul(buf, 10, &val); | 
|  | if (error) | 
|  | return error; | 
|  |  | 
|  | ad7879_toggle(ts, val); | 
|  |  | 
|  | return count; | 
|  | } | 
|  |  | 
|  | static DEVICE_ATTR(disable, 0664, ad7879_disable_show, ad7879_disable_store); | 
|  |  | 
|  | static struct attribute *ad7879_attributes[] = { | 
|  | &dev_attr_disable.attr, | 
|  | NULL | 
|  | }; | 
|  |  | 
|  | static const struct attribute_group ad7879_attr_group = { | 
|  | .attrs = ad7879_attributes, | 
|  | }; | 
|  |  | 
|  | #ifdef CONFIG_GPIOLIB | 
|  | static int ad7879_gpio_direction_input(struct gpio_chip *chip, | 
|  | unsigned gpio) | 
|  | { | 
|  | struct ad7879 *ts = container_of(chip, struct ad7879, gc); | 
|  | int err; | 
|  |  | 
|  | mutex_lock(&ts->mutex); | 
|  | ts->cmd_crtl2 |= AD7879_GPIO_EN | AD7879_GPIODIR | AD7879_GPIOPOL; | 
|  | err = ad7879_write(ts, AD7879_REG_CTRL2, ts->cmd_crtl2); | 
|  | mutex_unlock(&ts->mutex); | 
|  |  | 
|  | return err; | 
|  | } | 
|  |  | 
|  | static int ad7879_gpio_direction_output(struct gpio_chip *chip, | 
|  | unsigned gpio, int level) | 
|  | { | 
|  | struct ad7879 *ts = container_of(chip, struct ad7879, gc); | 
|  | int err; | 
|  |  | 
|  | mutex_lock(&ts->mutex); | 
|  | ts->cmd_crtl2 &= ~AD7879_GPIODIR; | 
|  | ts->cmd_crtl2 |= AD7879_GPIO_EN | AD7879_GPIOPOL; | 
|  | if (level) | 
|  | ts->cmd_crtl2 |= AD7879_GPIO_DATA; | 
|  | else | 
|  | ts->cmd_crtl2 &= ~AD7879_GPIO_DATA; | 
|  |  | 
|  | err = ad7879_write(ts, AD7879_REG_CTRL2, ts->cmd_crtl2); | 
|  | mutex_unlock(&ts->mutex); | 
|  |  | 
|  | return err; | 
|  | } | 
|  |  | 
|  | static int ad7879_gpio_get_value(struct gpio_chip *chip, unsigned gpio) | 
|  | { | 
|  | struct ad7879 *ts = container_of(chip, struct ad7879, gc); | 
|  | u16 val; | 
|  |  | 
|  | mutex_lock(&ts->mutex); | 
|  | val = ad7879_read(ts, AD7879_REG_CTRL2); | 
|  | mutex_unlock(&ts->mutex); | 
|  |  | 
|  | return !!(val & AD7879_GPIO_DATA); | 
|  | } | 
|  |  | 
|  | static void ad7879_gpio_set_value(struct gpio_chip *chip, | 
|  | unsigned gpio, int value) | 
|  | { | 
|  | struct ad7879 *ts = container_of(chip, struct ad7879, gc); | 
|  |  | 
|  | mutex_lock(&ts->mutex); | 
|  | if (value) | 
|  | ts->cmd_crtl2 |= AD7879_GPIO_DATA; | 
|  | else | 
|  | ts->cmd_crtl2 &= ~AD7879_GPIO_DATA; | 
|  |  | 
|  | ad7879_write(ts, AD7879_REG_CTRL2, ts->cmd_crtl2); | 
|  | mutex_unlock(&ts->mutex); | 
|  | } | 
|  |  | 
|  | static int ad7879_gpio_add(struct ad7879 *ts, | 
|  | const struct ad7879_platform_data *pdata) | 
|  | { | 
|  | int ret = 0; | 
|  |  | 
|  | mutex_init(&ts->mutex); | 
|  |  | 
|  | if (pdata->gpio_export) { | 
|  | ts->gc.direction_input = ad7879_gpio_direction_input; | 
|  | ts->gc.direction_output = ad7879_gpio_direction_output; | 
|  | ts->gc.get = ad7879_gpio_get_value; | 
|  | ts->gc.set = ad7879_gpio_set_value; | 
|  | ts->gc.can_sleep = 1; | 
|  | ts->gc.base = pdata->gpio_base; | 
|  | ts->gc.ngpio = 1; | 
|  | ts->gc.label = "AD7879-GPIO"; | 
|  | ts->gc.owner = THIS_MODULE; | 
|  | ts->gc.dev = ts->dev; | 
|  |  | 
|  | ret = gpiochip_add(&ts->gc); | 
|  | if (ret) | 
|  | dev_err(ts->dev, "failed to register gpio %d\n", | 
|  | ts->gc.base); | 
|  | } | 
|  |  | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | static void ad7879_gpio_remove(struct ad7879 *ts) | 
|  | { | 
|  | const struct ad7879_platform_data *pdata = ts->dev->platform_data; | 
|  | int ret; | 
|  |  | 
|  | if (pdata->gpio_export) { | 
|  | ret = gpiochip_remove(&ts->gc); | 
|  | if (ret) | 
|  | dev_err(ts->dev, "failed to remove gpio %d\n", | 
|  | ts->gc.base); | 
|  | } | 
|  | } | 
|  | #else | 
|  | static inline int ad7879_gpio_add(struct ad7879 *ts, | 
|  | const struct ad7879_platform_data *pdata) | 
|  | { | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static inline void ad7879_gpio_remove(struct ad7879 *ts) | 
|  | { | 
|  | } | 
|  | #endif | 
|  |  | 
|  | struct ad7879 *ad7879_probe(struct device *dev, u8 devid, unsigned int irq, | 
|  | const struct ad7879_bus_ops *bops) | 
|  | { | 
|  | struct ad7879_platform_data *pdata = dev->platform_data; | 
|  | struct ad7879 *ts; | 
|  | struct input_dev *input_dev; | 
|  | int err; | 
|  | u16 revid; | 
|  |  | 
|  | if (!irq) { | 
|  | dev_err(dev, "no IRQ?\n"); | 
|  | err = -EINVAL; | 
|  | goto err_out; | 
|  | } | 
|  |  | 
|  | if (!pdata) { | 
|  | dev_err(dev, "no platform data?\n"); | 
|  | err = -EINVAL; | 
|  | goto err_out; | 
|  | } | 
|  |  | 
|  | ts = kzalloc(sizeof(*ts), GFP_KERNEL); | 
|  | input_dev = input_allocate_device(); | 
|  | if (!ts || !input_dev) { | 
|  | err = -ENOMEM; | 
|  | goto err_free_mem; | 
|  | } | 
|  |  | 
|  | ts->bops = bops; | 
|  | ts->dev = dev; | 
|  | ts->input = input_dev; | 
|  | ts->irq = irq; | 
|  |  | 
|  | setup_timer(&ts->timer, ad7879_timer, (unsigned long) ts); | 
|  |  | 
|  | ts->x_plate_ohms = pdata->x_plate_ohms ? : 400; | 
|  | ts->pressure_max = pdata->pressure_max ? : ~0; | 
|  |  | 
|  | ts->first_conversion_delay = pdata->first_conversion_delay; | 
|  | ts->acquisition_time = pdata->acquisition_time; | 
|  | ts->averaging = pdata->averaging; | 
|  | ts->pen_down_acc_interval = pdata->pen_down_acc_interval; | 
|  | ts->median = pdata->median; | 
|  |  | 
|  | snprintf(ts->phys, sizeof(ts->phys), "%s/input0", dev_name(dev)); | 
|  |  | 
|  | input_dev->name = "AD7879 Touchscreen"; | 
|  | input_dev->phys = ts->phys; | 
|  | input_dev->dev.parent = dev; | 
|  | input_dev->id.bustype = bops->bustype; | 
|  |  | 
|  | input_dev->open = ad7879_open; | 
|  | input_dev->close = ad7879_close; | 
|  |  | 
|  | input_set_drvdata(input_dev, ts); | 
|  |  | 
|  | __set_bit(EV_ABS, input_dev->evbit); | 
|  | __set_bit(ABS_X, input_dev->absbit); | 
|  | __set_bit(ABS_Y, input_dev->absbit); | 
|  | __set_bit(ABS_PRESSURE, input_dev->absbit); | 
|  |  | 
|  | __set_bit(EV_KEY, input_dev->evbit); | 
|  | __set_bit(BTN_TOUCH, input_dev->keybit); | 
|  |  | 
|  | input_set_abs_params(input_dev, ABS_X, | 
|  | pdata->x_min ? : 0, | 
|  | pdata->x_max ? : MAX_12BIT, | 
|  | 0, 0); | 
|  | input_set_abs_params(input_dev, ABS_Y, | 
|  | pdata->y_min ? : 0, | 
|  | pdata->y_max ? : MAX_12BIT, | 
|  | 0, 0); | 
|  | input_set_abs_params(input_dev, ABS_PRESSURE, | 
|  | pdata->pressure_min, pdata->pressure_max, 0, 0); | 
|  |  | 
|  | err = ad7879_write(ts, AD7879_REG_CTRL2, AD7879_RESET); | 
|  | if (err < 0) { | 
|  | dev_err(dev, "Failed to write %s\n", input_dev->name); | 
|  | goto err_free_mem; | 
|  | } | 
|  |  | 
|  | revid = ad7879_read(ts, AD7879_REG_REVID); | 
|  | input_dev->id.product = (revid & 0xff); | 
|  | input_dev->id.version = revid >> 8; | 
|  | if (input_dev->id.product != devid) { | 
|  | dev_err(dev, "Failed to probe %s (%x vs %x)\n", | 
|  | input_dev->name, devid, revid); | 
|  | err = -ENODEV; | 
|  | goto err_free_mem; | 
|  | } | 
|  |  | 
|  | ts->cmd_crtl3 = AD7879_YPLUS_BIT | | 
|  | AD7879_XPLUS_BIT | | 
|  | AD7879_Z2_BIT | | 
|  | AD7879_Z1_BIT | | 
|  | AD7879_TEMPMASK_BIT | | 
|  | AD7879_AUXVBATMASK_BIT | | 
|  | AD7879_GPIOALERTMASK_BIT; | 
|  |  | 
|  | ts->cmd_crtl2 = AD7879_PM(AD7879_PM_DYN) | AD7879_DFR | | 
|  | AD7879_AVG(ts->averaging) | | 
|  | AD7879_MFS(ts->median) | | 
|  | AD7879_FCD(ts->first_conversion_delay); | 
|  |  | 
|  | ts->cmd_crtl1 = AD7879_MODE_INT | AD7879_MODE_SEQ1 | | 
|  | AD7879_ACQ(ts->acquisition_time) | | 
|  | AD7879_TMR(ts->pen_down_acc_interval); | 
|  |  | 
|  | err = request_threaded_irq(ts->irq, NULL, ad7879_irq, | 
|  | IRQF_TRIGGER_FALLING, | 
|  | dev_name(dev), ts); | 
|  | if (err) { | 
|  | dev_err(dev, "irq %d busy?\n", ts->irq); | 
|  | goto err_free_mem; | 
|  | } | 
|  |  | 
|  | __ad7879_disable(ts); | 
|  |  | 
|  | err = sysfs_create_group(&dev->kobj, &ad7879_attr_group); | 
|  | if (err) | 
|  | goto err_free_irq; | 
|  |  | 
|  | err = ad7879_gpio_add(ts, pdata); | 
|  | if (err) | 
|  | goto err_remove_attr; | 
|  |  | 
|  | err = input_register_device(input_dev); | 
|  | if (err) | 
|  | goto err_remove_gpio; | 
|  |  | 
|  | return ts; | 
|  |  | 
|  | err_remove_gpio: | 
|  | ad7879_gpio_remove(ts); | 
|  | err_remove_attr: | 
|  | sysfs_remove_group(&dev->kobj, &ad7879_attr_group); | 
|  | err_free_irq: | 
|  | free_irq(ts->irq, ts); | 
|  | err_free_mem: | 
|  | input_free_device(input_dev); | 
|  | kfree(ts); | 
|  | err_out: | 
|  | return ERR_PTR(err); | 
|  | } | 
|  | EXPORT_SYMBOL(ad7879_probe); | 
|  |  | 
|  | void ad7879_remove(struct ad7879 *ts) | 
|  | { | 
|  | ad7879_gpio_remove(ts); | 
|  | sysfs_remove_group(&ts->dev->kobj, &ad7879_attr_group); | 
|  | free_irq(ts->irq, ts); | 
|  | input_unregister_device(ts->input); | 
|  | kfree(ts); | 
|  | } | 
|  | EXPORT_SYMBOL(ad7879_remove); | 
|  |  | 
|  | MODULE_AUTHOR("Michael Hennerich <hennerich@blackfin.uclinux.org>"); | 
|  | MODULE_DESCRIPTION("AD7879(-1) touchscreen Driver"); | 
|  | MODULE_LICENSE("GPL"); |