| // SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| /* |
| * Copyright (c) 2019 BayLibre, SAS |
| * Author: Neil Armstrong <narmstrong@baylibre.com> |
| * Copyright (c) 2019 Christian Hewitt <christianshewitt@gmail.com> |
| */ |
| |
| /dts-v1/; |
| |
| #include "meson-g12b.dtsi" |
| #include "meson-g12b-s922x.dtsi" |
| #include <dt-bindings/input/input.h> |
| #include <dt-bindings/gpio/meson-g12a-gpio.h> |
| |
| / { |
| aliases { |
| serial0 = &uart_AO; |
| ethernet0 = ðmac; |
| }; |
| |
| chosen { |
| stdout-path = "serial0:115200n8"; |
| }; |
| |
| memory@0 { |
| device_type = "memory"; |
| reg = <0x0 0x0 0x0 0x40000000>; |
| }; |
| |
| emmc_pwrseq: emmc-pwrseq { |
| compatible = "mmc-pwrseq-emmc"; |
| reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>; |
| }; |
| |
| sdio_pwrseq: sdio-pwrseq { |
| compatible = "mmc-pwrseq-simple"; |
| reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>; |
| clocks = <&wifi32k>; |
| clock-names = "ext_clock"; |
| }; |
| |
| flash_1v8: regulator-flash_1v8 { |
| compatible = "regulator-fixed"; |
| regulator-name = "FLASH_1V8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| vin-supply = <&vcc_3v3>; |
| regulator-always-on; |
| }; |
| |
| main_12v: regulator-main_12v { |
| compatible = "regulator-fixed"; |
| regulator-name = "12V"; |
| regulator-min-microvolt = <12000000>; |
| regulator-max-microvolt = <12000000>; |
| regulator-always-on; |
| }; |
| |
| vcc_5v: regulator-vcc_5v { |
| compatible = "regulator-fixed"; |
| regulator-name = "VCC_5V"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| vin-supply = <&main_12v>; |
| |
| gpio = <&gpio GPIOH_8 GPIO_OPEN_DRAIN>; |
| enable-active-high; |
| }; |
| |
| vcc_1v8: regulator-vcc_1v8 { |
| compatible = "regulator-fixed"; |
| regulator-name = "VCC_1V8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| vin-supply = <&vcc_3v3>; |
| regulator-always-on; |
| }; |
| |
| vcc_3v3: regulator-vcc_3v3 { |
| compatible = "regulator-fixed"; |
| regulator-name = "VCC_3V3"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| vin-supply = <&vddao_3v3>; |
| regulator-always-on; |
| /* FIXME: actually controlled by VDDCPU_B_EN */ |
| }; |
| |
| vddcpu_a: regulator-vddcpu-a { |
| /* |
| * MP1653 Regulator. |
| */ |
| compatible = "pwm-regulator"; |
| |
| regulator-name = "VDDCPU_A"; |
| regulator-min-microvolt = <721000>; |
| regulator-max-microvolt = <1022000>; |
| |
| vin-supply = <&main_12v>; |
| |
| pwms = <&pwm_ab 0 1250 0>; |
| pwm-dutycycle-range = <100 0>; |
| |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| vddcpu_b: regulator-vddcpu-b { |
| /* |
| * MP1652 Regulator. |
| */ |
| compatible = "pwm-regulator"; |
| |
| regulator-name = "VDDCPU_B"; |
| regulator-min-microvolt = <721000>; |
| regulator-max-microvolt = <1022000>; |
| |
| vin-supply = <&main_12v>; |
| |
| pwms = <&pwm_AO_cd 1 1250 0>; |
| pwm-dutycycle-range = <100 0>; |
| |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| usb1_pow: regulator-usb1-pow { |
| compatible = "regulator-fixed"; |
| regulator-name = "USB1_POW"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| vin-supply = <&vcc_5v>; |
| |
| /* connected to SY6280A Power Switch */ |
| gpio = <&gpio GPIOA_8 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| |
| usb_pwr_en: regulator-usb-pwr-en { |
| compatible = "regulator-fixed"; |
| regulator-name = "USB_PWR_EN"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| vin-supply = <&vcc_5v>; |
| |
| /* Connected to USB3 Type-A Port power enable */ |
| gpio = <&gpio GPIOAO_7 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| |
| vddao_1v8: regulator-vddao-1v8 { |
| compatible = "regulator-fixed"; |
| regulator-name = "VDDAO_1V8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| vin-supply = <&vddao_3v3>; |
| regulator-always-on; |
| }; |
| |
| vddao_3v3: regulator-vddao-3v3 { |
| compatible = "regulator-fixed"; |
| regulator-name = "VDDAO_3V3"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| vin-supply = <&main_12v>; |
| regulator-always-on; |
| }; |
| |
| cvbs-connector { |
| compatible = "composite-video-connector"; |
| |
| port { |
| cvbs_connector_in: endpoint { |
| remote-endpoint = <&cvbs_vdac_out>; |
| }; |
| }; |
| }; |
| |
| hdmi-connector { |
| compatible = "hdmi-connector"; |
| type = "a"; |
| |
| port { |
| hdmi_connector_in: endpoint { |
| remote-endpoint = <&hdmi_tx_tmds_out>; |
| }; |
| }; |
| }; |
| |
| wifi32k: wifi32k { |
| compatible = "pwm-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <32768>; |
| pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */ |
| }; |
| }; |
| |
| &cec_AO { |
| pinctrl-0 = <&cec_ao_a_h_pins>; |
| pinctrl-names = "default"; |
| status = "disabled"; |
| hdmi-phandle = <&hdmi_tx>; |
| }; |
| |
| &cecb_AO { |
| pinctrl-0 = <&cec_ao_b_h_pins>; |
| pinctrl-names = "default"; |
| status = "okay"; |
| hdmi-phandle = <&hdmi_tx>; |
| }; |
| |
| &cpu0 { |
| cpu-supply = <&vddcpu_b>; |
| operating-points-v2 = <&cpu_opp_table_0>; |
| clocks = <&clkc CLKID_CPU_CLK>; |
| clock-latency = <50000>; |
| }; |
| |
| &cpu1 { |
| cpu-supply = <&vddcpu_b>; |
| operating-points-v2 = <&cpu_opp_table_0>; |
| clocks = <&clkc CLKID_CPU_CLK>; |
| clock-latency = <50000>; |
| }; |
| |
| &cpu100 { |
| cpu-supply = <&vddcpu_a>; |
| operating-points-v2 = <&cpub_opp_table_1>; |
| clocks = <&clkc CLKID_CPUB_CLK>; |
| clock-latency = <50000>; |
| }; |
| |
| &cpu101 { |
| cpu-supply = <&vddcpu_a>; |
| operating-points-v2 = <&cpub_opp_table_1>; |
| clocks = <&clkc CLKID_CPUB_CLK>; |
| clock-latency = <50000>; |
| }; |
| |
| &cpu102 { |
| cpu-supply = <&vddcpu_a>; |
| operating-points-v2 = <&cpub_opp_table_1>; |
| clocks = <&clkc CLKID_CPUB_CLK>; |
| clock-latency = <50000>; |
| }; |
| |
| &cpu103 { |
| cpu-supply = <&vddcpu_a>; |
| operating-points-v2 = <&cpub_opp_table_1>; |
| clocks = <&clkc CLKID_CPUB_CLK>; |
| clock-latency = <50000>; |
| }; |
| |
| &cvbs_vdac_port { |
| cvbs_vdac_out: endpoint { |
| remote-endpoint = <&cvbs_connector_in>; |
| }; |
| }; |
| |
| &ext_mdio { |
| external_phy: ethernet-phy@0 { |
| /* Realtek RTL8211F (0x001cc916) */ |
| reg = <0>; |
| max-speed = <1000>; |
| |
| reset-assert-us = <10000>; |
| reset-deassert-us = <80000>; |
| reset-gpios = <&gpio GPIOZ_15 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>; |
| |
| interrupt-parent = <&gpio_intc>; |
| /* MAC_INTR on GPIOZ_14 */ |
| interrupts = <26 IRQ_TYPE_LEVEL_LOW>; |
| }; |
| }; |
| |
| ðmac { |
| pinctrl-0 = <ð_pins>, <ð_rgmii_pins>; |
| pinctrl-names = "default"; |
| status = "okay"; |
| phy-mode = "rgmii"; |
| phy-handle = <&external_phy>; |
| amlogic,tx-delay-ns = <2>; |
| }; |
| |
| &hdmi_tx { |
| status = "okay"; |
| pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>; |
| pinctrl-names = "default"; |
| hdmi-supply = <&vcc_5v>; |
| }; |
| |
| &hdmi_tx_tmds_port { |
| hdmi_tx_tmds_out: endpoint { |
| remote-endpoint = <&hdmi_connector_in>; |
| }; |
| }; |
| |
| &ir { |
| status = "okay"; |
| pinctrl-0 = <&remote_input_ao_pins>; |
| pinctrl-names = "default"; |
| }; |
| |
| &pwm_ab { |
| pinctrl-0 = <&pwm_a_e_pins>; |
| pinctrl-names = "default"; |
| clocks = <&xtal>; |
| clock-names = "clkin0"; |
| status = "okay"; |
| }; |
| |
| &pwm_AO_cd { |
| pinctrl-0 = <&pwm_ao_d_e_pins>; |
| pinctrl-names = "default"; |
| clocks = <&xtal>; |
| clock-names = "clkin1"; |
| status = "okay"; |
| }; |
| |
| &pwm_ef { |
| pinctrl-0 = <&pwm_e_pins>; |
| pinctrl-names = "default"; |
| clocks = <&xtal>; |
| clock-names = "clkin0"; |
| status = "okay"; |
| }; |
| |
| /* SDIO */ |
| &sd_emmc_a { |
| status = "okay"; |
| pinctrl-0 = <&sdio_pins>; |
| pinctrl-1 = <&sdio_clk_gate_pins>; |
| pinctrl-names = "default", "clk-gate"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| bus-width = <4>; |
| cap-sd-highspeed; |
| max-frequency = <100000000>; |
| |
| /* WiFi firmware requires power to be kept while in suspend */ |
| keep-power-in-suspend; |
| |
| non-removable; |
| disable-wp; |
| |
| mmc-pwrseq = <&sdio_pwrseq>; |
| |
| vmmc-supply = <&vddao_3v3>; |
| vqmmc-supply = <&vddao_1v8>; |
| |
| brcmf: wifi@1 { |
| reg = <1>; |
| compatible = "brcm,bcm4329-fmac"; |
| }; |
| }; |
| |
| /* SD card */ |
| &sd_emmc_b { |
| status = "okay"; |
| pinctrl-0 = <&sdcard_c_pins>; |
| pinctrl-1 = <&sdcard_clk_gate_c_pins>; |
| pinctrl-names = "default", "clk-gate"; |
| |
| bus-width = <4>; |
| cap-sd-highspeed; |
| max-frequency = <50000000>; |
| disable-wp; |
| |
| cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>; |
| vmmc-supply = <&vddao_3v3>; |
| vqmmc-supply = <&vddao_3v3>; |
| }; |
| |
| /* eMMC */ |
| &sd_emmc_c { |
| status = "okay"; |
| pinctrl-0 = <&emmc_ctrl_pins>, <&emmc_data_8b_pins>, <&emmc_ds_pins>; |
| pinctrl-1 = <&emmc_clk_gate_pins>; |
| pinctrl-names = "default", "clk-gate"; |
| |
| bus-width = <8>; |
| cap-mmc-highspeed; |
| max-frequency = <100000000>; |
| disable-wp; |
| |
| mmc-pwrseq = <&emmc_pwrseq>; |
| vmmc-supply = <&vcc_3v3>; |
| vqmmc-supply = <&flash_1v8>; |
| }; |
| |
| &uart_A { |
| status = "okay"; |
| pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>; |
| pinctrl-names = "default"; |
| uart-has-rtscts; |
| |
| bluetooth { |
| compatible = "brcm,bcm43438-bt"; |
| shutdown-gpios = <&gpio GPIOX_17 GPIO_ACTIVE_HIGH>; |
| max-speed = <2000000>; |
| clocks = <&wifi32k>; |
| clock-names = "lpo"; |
| }; |
| }; |
| |
| &uart_AO { |
| status = "okay"; |
| pinctrl-0 = <&uart_ao_a_pins>; |
| pinctrl-names = "default"; |
| }; |
| |
| &usb { |
| status = "okay"; |
| dr_mode = "host"; |
| vbus-supply = <&usb_pwr_en>; |
| }; |
| |
| &usb2_phy0 { |
| phy-supply = <&usb1_pow>; |
| }; |
| |
| &usb2_phy1 { |
| phy-supply = <&usb1_pow>; |
| }; |
