| // SPDX-License-Identifier: (GPL-2.0 OR MIT) |
| /* |
| * Device Tree file for the Turris Omnia |
| * |
| * Copyright (C) 2016 Uwe Kleine-König <uwe@kleine-koenig.org> |
| * Copyright (C) 2016 Tomas Hlavacek <tmshlvkc@gmail.com> |
| * |
| * Schematic available at https://www.turris.cz/doc/_media/rtrom01-schema.pdf |
| */ |
| |
| /dts-v1/; |
| |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/input/input.h> |
| #include <dt-bindings/leds/common.h> |
| #include "armada-385.dtsi" |
| |
| / { |
| model = "Turris Omnia"; |
| compatible = "cznic,turris-omnia", "marvell,armada385", "marvell,armada380"; |
| |
| chosen { |
| stdout-path = &uart0; |
| }; |
| |
| aliases { |
| ethernet0 = ð0; |
| ethernet1 = ð1; |
| ethernet2 = ð2; |
| }; |
| |
| memory { |
| device_type = "memory"; |
| reg = <0x00000000 0x40000000>; /* 1024 MB */ |
| }; |
| |
| soc { |
| ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000 |
| MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000 |
| MBUS_ID(0x09, 0x19) 0 0xf1100000 0x10000 |
| MBUS_ID(0x09, 0x15) 0 0xf1110000 0x10000 |
| MBUS_ID(0x0c, 0x04) 0 0xf1200000 0x100000>; |
| |
| internal-regs { |
| |
| /* USB part of the PCIe2/USB 2.0 port */ |
| usb@58000 { |
| status = "okay"; |
| }; |
| |
| sata@a8000 { |
| status = "okay"; |
| }; |
| |
| sdhci@d8000 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&sdhci_pins>; |
| status = "okay"; |
| |
| bus-width = <8>; |
| no-1-8-v; |
| non-removable; |
| }; |
| |
| usb3@f0000 { |
| status = "okay"; |
| }; |
| |
| usb3@f8000 { |
| status = "okay"; |
| }; |
| }; |
| |
| pcie { |
| status = "okay"; |
| |
| pcie@1,0 { |
| /* Port 0, Lane 0 */ |
| status = "okay"; |
| slot-power-limit-milliwatt = <10000>; |
| }; |
| |
| pcie@2,0 { |
| /* Port 1, Lane 0 */ |
| status = "okay"; |
| slot-power-limit-milliwatt = <10000>; |
| }; |
| |
| pcie@3,0 { |
| /* Port 2, Lane 0 */ |
| status = "okay"; |
| slot-power-limit-milliwatt = <10000>; |
| }; |
| }; |
| }; |
| |
| sfp: sfp { |
| compatible = "sff,sfp"; |
| i2c-bus = <&sfp_i2c>; |
| tx-fault-gpios = <&pcawan 0 GPIO_ACTIVE_HIGH>; |
| tx-disable-gpios = <&pcawan 1 GPIO_ACTIVE_HIGH>; |
| rate-select0-gpios = <&pcawan 2 GPIO_ACTIVE_HIGH>; |
| los-gpios = <&pcawan 3 GPIO_ACTIVE_HIGH>; |
| mod-def0-gpios = <&pcawan 4 GPIO_ACTIVE_LOW>; |
| maximum-power-milliwatt = <3000>; |
| |
| /* |
| * For now this has to be enabled at boot time by U-Boot when |
| * a SFP module is present. Read more in the comment in the |
| * eth2 node below. |
| */ |
| status = "disabled"; |
| }; |
| |
| sound { |
| compatible = "simple-audio-card"; |
| simple-audio-card,name = "SPDIF"; |
| simple-audio-card,format = "i2s"; |
| |
| simple-audio-card,cpu { |
| sound-dai = <&audio_controller 1>; |
| }; |
| |
| simple-audio-card,codec { |
| sound-dai = <&spdif_out>; |
| }; |
| }; |
| |
| spdif_out: spdif-out { |
| #sound-dai-cells = <0>; |
| compatible = "linux,spdif-dit"; |
| }; |
| }; |
| |
| &audio_controller { |
| /* Pin header U16, GPIO51 in SPDIFO mode */ |
| pinctrl-0 = <&spdif_pins>; |
| pinctrl-names = "default"; |
| spdif-mode; |
| status = "okay"; |
| }; |
| |
| &bm { |
| status = "okay"; |
| }; |
| |
| &bm_bppi { |
| status = "okay"; |
| }; |
| |
| /* Connected to 88E6176 switch, port 6 */ |
| ð0 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&ge0_rgmii_pins>; |
| status = "okay"; |
| phy-mode = "rgmii"; |
| buffer-manager = <&bm>; |
| bm,pool-long = <0>; |
| bm,pool-short = <3>; |
| |
| fixed-link { |
| speed = <1000>; |
| full-duplex; |
| }; |
| }; |
| |
| /* Connected to 88E6176 switch, port 5 */ |
| ð1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&ge1_rgmii_pins>; |
| status = "okay"; |
| phy-mode = "rgmii"; |
| buffer-manager = <&bm>; |
| bm,pool-long = <1>; |
| bm,pool-short = <3>; |
| |
| fixed-link { |
| speed = <1000>; |
| full-duplex; |
| }; |
| }; |
| |
| /* WAN port */ |
| ð2 { |
| /* |
| * eth2 is connected via a multiplexor to both the SFP cage and to |
| * ethernet-phy@1. The multiplexor switches the signal to SFP cage when |
| * a SFP module is present, as determined by the mode-def0 GPIO. |
| * |
| * Until kernel supports this configuration properly, in case SFP module |
| * is present, U-Boot has to enable the sfp node above, remove phy |
| * handle and add managed = "in-band-status" property. |
| */ |
| status = "okay"; |
| phy-mode = "sgmii"; |
| phy-handle = <&phy1>; |
| phys = <&comphy5 2>; |
| sfp = <&sfp>; |
| buffer-manager = <&bm>; |
| bm,pool-long = <2>; |
| bm,pool-short = <3>; |
| label = "wan"; |
| }; |
| |
| &i2c0 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c0_pins>; |
| status = "okay"; |
| |
| i2cmux@70 { |
| compatible = "nxp,pca9547"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x70>; |
| |
| i2c@0 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0>; |
| |
| /* STM32F0 command interface at address 0x2a */ |
| |
| led-controller@2b { |
| compatible = "cznic,turris-omnia-leds"; |
| reg = <0x2b>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "okay"; |
| |
| /* |
| * LEDs are controlled by MCU (STM32F0) at |
| * address 0x2b. |
| * |
| * LED functions are not stable yet: |
| * - there are 3 LEDs connected via MCU to PCIe |
| * ports. One of these ports supports mSATA. |
| * There is no mSATA nor PCIe function. |
| * For now we use LED_FUNCTION_WLAN, since |
| * in most cases users have wifi cards in |
| * these slots |
| * - there are 2 LEDs dedicated for user: A and |
| * B. Again there is no such function defined. |
| * For now we use LED_FUNCTION_INDICATOR |
| */ |
| |
| multi-led@0 { |
| reg = <0x0>; |
| color = <LED_COLOR_ID_RGB>; |
| function = LED_FUNCTION_INDICATOR; |
| function-enumerator = <2>; |
| }; |
| |
| multi-led@1 { |
| reg = <0x1>; |
| color = <LED_COLOR_ID_RGB>; |
| function = LED_FUNCTION_INDICATOR; |
| function-enumerator = <1>; |
| }; |
| |
| multi-led@2 { |
| reg = <0x2>; |
| color = <LED_COLOR_ID_RGB>; |
| function = LED_FUNCTION_WLAN; |
| function-enumerator = <3>; |
| }; |
| |
| multi-led@3 { |
| reg = <0x3>; |
| color = <LED_COLOR_ID_RGB>; |
| function = LED_FUNCTION_WLAN; |
| function-enumerator = <2>; |
| }; |
| |
| multi-led@4 { |
| reg = <0x4>; |
| color = <LED_COLOR_ID_RGB>; |
| function = LED_FUNCTION_WLAN; |
| function-enumerator = <1>; |
| }; |
| |
| multi-led@5 { |
| reg = <0x5>; |
| color = <LED_COLOR_ID_RGB>; |
| function = LED_FUNCTION_WAN; |
| }; |
| |
| multi-led@6 { |
| reg = <0x6>; |
| color = <LED_COLOR_ID_RGB>; |
| function = LED_FUNCTION_LAN; |
| function-enumerator = <4>; |
| }; |
| |
| multi-led@7 { |
| reg = <0x7>; |
| color = <LED_COLOR_ID_RGB>; |
| function = LED_FUNCTION_LAN; |
| function-enumerator = <3>; |
| }; |
| |
| multi-led@8 { |
| reg = <0x8>; |
| color = <LED_COLOR_ID_RGB>; |
| function = LED_FUNCTION_LAN; |
| function-enumerator = <2>; |
| }; |
| |
| multi-led@9 { |
| reg = <0x9>; |
| color = <LED_COLOR_ID_RGB>; |
| function = LED_FUNCTION_LAN; |
| function-enumerator = <1>; |
| }; |
| |
| multi-led@a { |
| reg = <0xa>; |
| color = <LED_COLOR_ID_RGB>; |
| function = LED_FUNCTION_LAN; |
| function-enumerator = <0>; |
| }; |
| |
| multi-led@b { |
| reg = <0xb>; |
| color = <LED_COLOR_ID_RGB>; |
| function = LED_FUNCTION_POWER; |
| }; |
| }; |
| |
| eeprom@54 { |
| compatible = "atmel,24c64"; |
| reg = <0x54>; |
| |
| /* The EEPROM contains data for bootloader. |
| * Contents: |
| * struct omnia_eeprom { |
| * u32 magic; (=0x0341a034 in LE) |
| * u32 ramsize; (in GiB) |
| * char regdomain[4]; |
| * u32 crc32; |
| * }; |
| */ |
| }; |
| }; |
| |
| i2c@1 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <1>; |
| |
| /* routed to PCIe0/mSATA connector (CN7A) */ |
| }; |
| |
| i2c@2 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <2>; |
| |
| /* routed to PCIe1/USB2 connector (CN61A) */ |
| }; |
| |
| i2c@3 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <3>; |
| |
| /* routed to PCIe2 connector (CN62A) */ |
| }; |
| |
| sfp_i2c: i2c@4 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <4>; |
| |
| /* routed to SFP+ */ |
| }; |
| |
| i2c@5 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <5>; |
| |
| /* ATSHA204A-MAHDA-T crypto module */ |
| crypto@64 { |
| compatible = "atmel,atsha204a"; |
| reg = <0x64>; |
| }; |
| }; |
| |
| i2c@6 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <6>; |
| |
| /* exposed on pin header */ |
| }; |
| |
| i2c@7 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <7>; |
| |
| pcawan: gpio@71 { |
| /* |
| * GPIO expander for SFP+ signals and |
| * and phy irq |
| */ |
| compatible = "nxp,pca9538"; |
| reg = <0x71>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pcawan_pins>; |
| |
| interrupt-parent = <&gpio1>; |
| interrupts = <14 IRQ_TYPE_LEVEL_LOW>; |
| |
| gpio-controller; |
| #gpio-cells = <2>; |
| }; |
| }; |
| }; |
| }; |
| |
| &mdio { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&mdio_pins>; |
| status = "okay"; |
| |
| phy1: ethernet-phy@1 { |
| compatible = "ethernet-phy-ieee802.3-c22"; |
| reg = <1>; |
| marvell,reg-init = <3 18 0 0x4985>, |
| <3 16 0xfff0 0x0001>; |
| |
| /* irq is connected to &pcawan pin 7 */ |
| }; |
| |
| /* Switch MV88E6176 at address 0x10 */ |
| ethernet-switch@10 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&swint_pins>; |
| compatible = "marvell,mv88e6085"; |
| |
| dsa,member = <0 0>; |
| reg = <0x10>; |
| |
| interrupt-parent = <&gpio1>; |
| interrupts = <13 IRQ_TYPE_LEVEL_LOW>; |
| |
| ethernet-ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| ethernet-port@0 { |
| reg = <0>; |
| label = "lan0"; |
| }; |
| |
| ethernet-port@1 { |
| reg = <1>; |
| label = "lan1"; |
| }; |
| |
| ethernet-port@2 { |
| reg = <2>; |
| label = "lan2"; |
| }; |
| |
| ethernet-port@3 { |
| reg = <3>; |
| label = "lan3"; |
| }; |
| |
| ethernet-port@4 { |
| reg = <4>; |
| label = "lan4"; |
| }; |
| |
| ethernet-port@5 { |
| reg = <5>; |
| ethernet = <ð1>; |
| phy-mode = "rgmii-id"; |
| |
| fixed-link { |
| speed = <1000>; |
| full-duplex; |
| }; |
| }; |
| |
| ethernet-port@6 { |
| reg = <6>; |
| ethernet = <ð0>; |
| phy-mode = "rgmii-id"; |
| |
| fixed-link { |
| speed = <1000>; |
| full-duplex; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| &pinctrl { |
| pcawan_pins: pcawan-pins { |
| marvell,pins = "mpp46"; |
| marvell,function = "gpio"; |
| }; |
| |
| swint_pins: swint-pins { |
| marvell,pins = "mpp45"; |
| marvell,function = "gpio"; |
| }; |
| |
| spi0cs0_pins: spi0cs0-pins { |
| marvell,pins = "mpp25"; |
| marvell,function = "spi0"; |
| }; |
| |
| spi0cs2_pins: spi0cs2-pins { |
| marvell,pins = "mpp26"; |
| marvell,function = "spi0"; |
| }; |
| }; |
| |
| &spi0 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&spi0_pins &spi0cs0_pins>; |
| status = "okay"; |
| |
| flash@0 { |
| compatible = "spansion,s25fl164k", "jedec,spi-nor"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| reg = <0>; |
| spi-max-frequency = <40000000>; |
| |
| partitions { |
| compatible = "fixed-partitions"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| partition@0 { |
| reg = <0x0 0x00100000>; |
| label = "U-Boot"; |
| }; |
| |
| partition@100000 { |
| reg = <0x00100000 0x00700000>; |
| label = "Rescue system"; |
| }; |
| }; |
| }; |
| |
| /* MISO, MOSI, SCLK and CS2 are routed to pin header CN11 */ |
| }; |
| |
| &uart0 { |
| /* Pin header CN10 */ |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart0_pins>; |
| status = "okay"; |
| }; |
| |
| &uart1 { |
| /* Pin header CN11 */ |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart1_pins>; |
| status = "okay"; |
| }; |
