| /* |
| * Copyright (C) ST-Ericsson SA 2010 |
| * |
| * License terms: GNU General Public License (GPL) version 2 |
| */ |
| |
| #ifndef __BOARD_MOP500_H |
| #define __BOARD_MOP500_H |
| |
| /* For NOMADIK_NR_GPIO */ |
| #include "irqs.h" |
| #include <linux/platform_data/asoc-ux500-msp.h> |
| #include <linux/amba/mmci.h> |
| |
| /* Snowball specific GPIO assignments, this board has no GPIO expander */ |
| #define SNOWBALL_ACCEL_INT1_GPIO 163 |
| #define SNOWBALL_ACCEL_INT2_GPIO 164 |
| #define SNOWBALL_MAGNET_DRDY_GPIO 165 |
| #define SNOWBALL_SDMMC_EN_GPIO 217 |
| #define SNOWBALL_SDMMC_1V8_3V_GPIO 228 |
| #define SNOWBALL_SDMMC_CD_GPIO 218 |
| |
| /* HREFv60-specific GPIO assignments, this board has no GPIO expander */ |
| #define HREFV60_SDMMC_1V8_3V_GPIO 5 |
| #define HREFV60_CAMERA_FLASH_ENABLE 21 |
| #define HREFV60_MAGNET_DRDY_GPIO 32 |
| #define HREFV60_DISP1_RST_GPIO 65 |
| #define HREFV60_DISP2_RST_GPIO 66 |
| #define HREFV60_ACCEL_INT1_GPIO 82 |
| #define HREFV60_ACCEL_INT2_GPIO 83 |
| #define HREFV60_SDMMC_CD_GPIO 95 |
| #define HREFV60_XSHUTDOWN_SECONDARY_SENSOR 140 |
| #define HREFV60_TOUCH_RST_GPIO 143 |
| #define HREFV60_HAL_SW_GPIO 145 |
| #define HREFV60_SDMMC_EN_GPIO 169 |
| #define HREFV60_MMIO_XENON_CHARGE 170 |
| #define HREFV60_PROX_SENSE_GPIO 217 |
| |
| /* MOP500 generic GPIOs */ |
| #define CAMERA_FLASH_INT_PIN 7 |
| #define CYPRESS_TOUCH_INT_PIN 84 |
| #define XSHUTDOWN_PRIMARY_SENSOR 141 |
| #define XSHUTDOWN_SECONDARY_SENSOR 142 |
| #define CYPRESS_TOUCH_RST_GPIO 143 |
| #define MOP500_HDMI_RST_GPIO 196 |
| #define CYPRESS_SLAVE_SELECT_GPIO 216 |
| |
| /* GPIOs on the TC35892 expander */ |
| #define MOP500_EGPIO(x) (NOMADIK_NR_GPIO + (x)) |
| #define GPIO_MAGNET_DRDY MOP500_EGPIO(1) |
| #define GPIO_SDMMC_CD MOP500_EGPIO(3) |
| #define GPIO_CAMERA_FLASH_ENABLE MOP500_EGPIO(4) |
| #define GPIO_MMIO_XENON_CHARGE MOP500_EGPIO(5) |
| #define GPIO_PROX_SENSOR MOP500_EGPIO(7) |
| #define GPIO_HAL_SENSOR MOP500_EGPIO(8) |
| #define GPIO_ACCEL_INT1 MOP500_EGPIO(10) |
| #define GPIO_ACCEL_INT2 MOP500_EGPIO(11) |
| #define GPIO_BU21013_CS MOP500_EGPIO(13) |
| #define MOP500_DISP2_RST_GPIO MOP500_EGPIO(14) |
| #define MOP500_DISP1_RST_GPIO MOP500_EGPIO(15) |
| #define GPIO_SDMMC_EN MOP500_EGPIO(17) |
| #define GPIO_SDMMC_1V8_3V_SEL MOP500_EGPIO(18) |
| #define MOP500_EGPIO_END MOP500_EGPIO(24) |
| |
| /* |
| * GPIOs on the AB8500 mixed-signals circuit |
| * Notice that we subtract 1 from the number passed into the macro, this is |
| * because the AB8500 GPIO pins are enumbered starting from 1, so the value in |
| * parens matches the GPIO pin number in the data sheet. |
| */ |
| #define MOP500_AB8500_PIN_GPIO(x) (MOP500_EGPIO_END + (x) - 1) |
| /*Snowball AB8500 GPIO */ |
| #define SNOWBALL_VSMPS2_1V8_GPIO MOP500_AB8500_PIN_GPIO(1) /* SYSCLKREQ2/GPIO1 */ |
| #define SNOWBALL_PM_GPIO1_GPIO MOP500_AB8500_PIN_GPIO(2) /* SYSCLKREQ3/GPIO2 */ |
| #define SNOWBALL_WLAN_CLK_REQ_GPIO MOP500_AB8500_PIN_GPIO(3) /* SYSCLKREQ4/GPIO3 */ |
| #define SNOWBALL_PM_GPIO4_GPIO MOP500_AB8500_PIN_GPIO(4) /* SYSCLKREQ6/GPIO4 */ |
| #define SNOWBALL_EN_3V6_GPIO MOP500_AB8500_PIN_GPIO(16) /* PWMOUT3/GPIO16 */ |
| #define SNOWBALL_PME_ETH_GPIO MOP500_AB8500_PIN_GPIO(24) /* SYSCLKREQ7/GPIO24 */ |
| #define SNOWBALL_EN_3V3_ETH_GPIO MOP500_AB8500_PIN_GPIO(26) /* GPIO26 */ |
| |
| struct device; |
| extern struct mmci_platform_data mop500_sdi0_data; |
| extern struct mmci_platform_data mop500_sdi1_data; |
| extern struct mmci_platform_data mop500_sdi2_data; |
| extern struct mmci_platform_data mop500_sdi4_data; |
| extern struct msp_i2s_platform_data msp0_platform_data; |
| extern struct msp_i2s_platform_data msp1_platform_data; |
| extern struct msp_i2s_platform_data msp2_platform_data; |
| extern struct msp_i2s_platform_data msp3_platform_data; |
| extern struct pl022_ssp_controller ssp0_plat; |
| |
| void __init mop500_pinmaps_init(void); |
| void __init snowball_pinmaps_init(void); |
| void __init hrefv60_pinmaps_init(void); |
| |
| #endif |
