arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts - linux - Git at Google

 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
 /*
  * Copyright (C) 2019 Icenowy Zheng <icenowy@aosc.xyz>
  *
  */

 /dts-v1/;

 #include "sun50i-a64.dtsi"
 #include "sun50i-a64-cpu-opp.dtsi"

 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/pwm/pwm.h>

 / {
 	model = "PineTab, Development Sample";
 	compatible = "pine64,pinetab", "allwinner,sun50i-a64";

 	aliases {
 		serial0 = &uart0;
 		ethernet0 = &rtl8723cs;
 	};

 	backlight: backlight {
 		compatible = "pwm-backlight";
 		pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
 		brightness-levels = <0 16 18 20 22 24 26 29 32 35 38 42 46 51 56 62 68 75 83 91 100>;
 		default-brightness-level = <15>;
 		enable-gpios = <&pio 3 23 GPIO_ACTIVE_HIGH>; /* PD23 */
 		power-supply = <&vdd_bl>;
 	};

 	chosen {
 		stdout-path = "serial0:115200n8";
 	};

 	hdmi-connector {
 		compatible = "hdmi-connector";
 		type = "c";

 		port {
 			hdmi_con_in: endpoint {
 				remote-endpoint = <&hdmi_out_con>;
 			};
 		};
 	};

 	i2c-csi {
 		compatible = "i2c-gpio";
 		sda-gpios = <&pio 4 13 GPIO_ACTIVE_HIGH>; /* PE13 */
 		scl-gpios = <&pio 4 12 GPIO_ACTIVE_HIGH>; /* PE12 */
 		i2c-gpio,delay-us = <5>;
 		#address-cells = <1>;
 		#size-cells = <0>;

 		/* Rear camera */
 		ov5640: camera@3c {
 			compatible = "ovti,ov5640";
 			reg = <0x3c>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&csi_mclk_pin>;
 			clocks = <&ccu CLK_CSI_MCLK>;
 			clock-names = "xclk";

 			AVDD-supply = <&reg_dldo3>;
 			DOVDD-supply = <&reg_aldo1>;
 			DVDD-supply = <&reg_eldo3>;
 			reset-gpios = <&pio 4 14 GPIO_ACTIVE_LOW>; /* PE14 */
 			powerdown-gpios = <&pio 4 15 GPIO_ACTIVE_HIGH>; /* PE15 */

 			port {
 				ov5640_ep: endpoint {
 					remote-endpoint = <&csi_ep>;
 					bus-width = <8>;
 					hsync-active = <1>; /* Active high */
 					vsync-active = <0>; /* Active low */
 					data-active = <1>;  /* Active high */
 					pclk-sample = <1>;  /* Rising */
 				};
 			};
 		};
 	};

 	speaker_amp: audio-amplifier {
 		compatible = "simple-audio-amplifier";
 		enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */
 		sound-name-prefix = "Speaker Amp";
 	};

 	vdd_bl: regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "bl-3v3";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 		gpio = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */
 		enable-active-high;
 	};

 	wifi_pwrseq: wifi_pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
 		post-power-on-delay-ms = <200>;
 	};
 };

 &codec {
 	status = "okay";
 };

 &codec_analog {
 	cpvdd-supply = <&reg_eldo1>;
 	status = "okay";
 };

 &cpu0 {
 	cpu-supply = <&reg_dcdc2>;
 };

 &cpu1 {
 	cpu-supply = <&reg_dcdc2>;
 };

 &cpu2 {
 	cpu-supply = <&reg_dcdc2>;
 };

 &cpu3 {
 	cpu-supply = <&reg_dcdc2>;
 };

 &csi {
 	status = "okay";

 	port {
 		csi_ep: endpoint {
 			remote-endpoint = <&ov5640_ep>;
 			bus-width = <8>;
 			hsync-active = <1>; /* Active high */
 			vsync-active = <0>; /* Active low */
 			data-active = <1>;  /* Active high */
 			pclk-sample = <1>;  /* Rising */
 		};
 	};
 };

 &dai {
 	status = "okay";
 };

 &de {
 	status = "okay";
 };

 &dphy {
 	status = "okay";
 };

 &dsi {
 	vcc-dsi-supply = <&reg_dldo1>;
 	status = "okay";

 	panel@0 {
 		compatible = "feixin,k101-im2ba02";
 		reg = <0>;
 		avdd-supply = <&reg_dc1sw>;
 		dvdd-supply = <&reg_dc1sw>;
 		cvdd-supply = <&reg_ldo_io1>;
 		reset-gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* PD24 */
 		backlight = <&backlight>;
 	};
 };

 &ehci0 {
 	status = "okay";
 };

 &ehci1 {
 	status = "okay";
 };

 &i2c0 {
 	status = "okay";

 	touchscreen@5d {
 		compatible = "goodix,gt9271";
 		reg = <0x5d>;
 		interrupt-parent = <&pio>;
 		interrupts = <7 4 IRQ_TYPE_LEVEL_HIGH>; /* PH4 */
 		irq-gpios = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
 		reset-gpios = <&pio 7 8 GPIO_ACTIVE_HIGH>; /* PH8 */
 		AVDD28-supply = <&reg_ldo_io1>;
 	};
 };

 &i2c0_pins {
 	bias-pull-up;
 };

 &i2c1 {
 	status = "okay";

 	/* TODO: add Bochs BMA223 accelerometer here */
 };

 &lradc {
 	vref-supply = <&reg_aldo3>;
 	status = "okay";

 	button-200 {
 		label = "Volume Up";
 		linux,code = <KEY_VOLUMEUP>;
 		channel = <0>;
 		voltage = <200000>;
 	};

 	button-400 {
 		label = "Volume Down";
 		linux,code = <KEY_VOLUMEDOWN>;
 		channel = <0>;
 		voltage = <400000>;
 	};
 };

 &mixer1 {
 	status = "okay";
 };

 &mmc0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc0_pins>;
 	vmmc-supply = <&reg_dcdc1>;
 	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
 	disable-wp;
 	bus-width = <4>;
 	status = "okay";
 };

 &mmc1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc1_pins>;
 	vmmc-supply = <&reg_dldo4>;
 	vqmmc-supply = <&reg_eldo1>;
 	mmc-pwrseq = <&wifi_pwrseq>;
 	bus-width = <4>;
 	non-removable;
 	status = "okay";

 	rtl8723cs: wifi@1 {
 		reg = <1>;
 	};
 };

 &mmc2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc2_pins>;
 	vmmc-supply = <&reg_dcdc1>;
 	vqmmc-supply = <&reg_dcdc1>;
 	bus-width = <8>;
 	non-removable;
 	cap-mmc-hw-reset;
 	status = "okay";
 };

 &ohci0 {
 	status = "okay";
 };

 &pwm {
 	status = "okay";
 };

 &r_rsb {
 	status = "okay";

 	axp803: pmic@3a3 {
 		compatible = "x-powers,axp803";
 		reg = <0x3a3>;
 		interrupt-parent = <&r_intc>;
 		interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>;
 		x-powers,drive-vbus-en;
 	};
 };

 #include "axp803.dtsi"

 &ac_power_supply {
 	status = "okay";
 };

 &battery_power_supply {
 	status = "okay";
 };

 &reg_aldo1 {
 	regulator-min-microvolt = <2800000>;
 	regulator-max-microvolt = <2800000>;
 	regulator-name = "dovdd-csi";
 };

 &reg_aldo2 {
 	regulator-always-on;
 	regulator-min-microvolt = <1800000>;
 	regulator-max-microvolt = <3300000>;
 	regulator-name = "vcc-pl";
 };

 &reg_aldo3 {
 	regulator-always-on;
 	regulator-min-microvolt = <2700000>;
 	regulator-max-microvolt = <3300000>;
 	regulator-name = "vcc-pll-avcc";
 };

 &reg_dc1sw {
 	regulator-name = "vcc-lcd";
 };

 &reg_dcdc1 {
 	regulator-always-on;
 	regulator-min-microvolt = <3300000>;
 	regulator-max-microvolt = <3300000>;
 	regulator-name = "vcc-3v3";
 };

 &reg_dcdc2 {
 	regulator-always-on;
 	regulator-min-microvolt = <1000000>;
 	regulator-max-microvolt = <1300000>;
 	regulator-name = "vdd-cpux";
 };

 /* DCDC3 is polyphased with DCDC2 */

 &reg_dcdc5 {
 	regulator-always-on;
 	regulator-min-microvolt = <1200000>;
 	regulator-max-microvolt = <1200000>;
 	regulator-name = "vcc-dram";
 };

 &reg_dcdc6 {
 	regulator-always-on;
 	regulator-min-microvolt = <1100000>;
 	regulator-max-microvolt = <1100000>;
 	regulator-name = "vdd-sys";
 };

 &reg_dldo1 {
 	regulator-always-on;
 	regulator-min-microvolt = <3300000>;
 	regulator-max-microvolt = <3300000>;
 	regulator-name = "vcc-hdmi-dsi-sensor";
 };

 &reg_dldo3 {
 	regulator-min-microvolt = <2800000>;
 	regulator-max-microvolt = <2800000>;
 	regulator-name = "avdd-csi";
 };

 &reg_dldo4 {
 	regulator-min-microvolt = <3300000>;
 	regulator-max-microvolt = <3300000>;
 	regulator-name = "vcc-wifi";
 };

 &reg_drivevbus {
 	regulator-name = "usb0-vbus";
 	status = "okay";
 };

 &reg_eldo1 {
 	regulator-always-on;
 	regulator-min-microvolt = <1800000>;
 	regulator-max-microvolt = <1800000>;
 	regulator-name = "cpvdd";
 };

 &reg_eldo2 {
 	regulator-min-microvolt = <1800000>;
 	regulator-max-microvolt = <1800000>;
 	regulator-name = "vcca-1v8";
 };

 &reg_eldo3 {
 	regulator-min-microvolt = <1800000>;
 	regulator-max-microvolt = <1800000>;
 	regulator-name = "dvdd-1v8-csi";
 };

 &reg_fldo1 {
 	regulator-min-microvolt = <1200000>;
 	regulator-max-microvolt = <1200000>;
 	regulator-name = "vcc-1v2-hsic";
 };

 &reg_fldo2 {
 	regulator-always-on;
 	regulator-min-microvolt = <1100000>;
 	regulator-max-microvolt = <1100000>;
 	regulator-name = "vdd-cpus";
 };

 &reg_ldo_io0 {
 	regulator-min-microvolt = <3300000>;
 	regulator-max-microvolt = <3300000>;
 	regulator-name = "vcc-usb";
 	status = "okay";
 };

 &reg_ldo_io1 {
 	regulator-min-microvolt = <3300000>;
 	regulator-max-microvolt = <3300000>;
 	regulator-enable-ramp-delay = <3500000>;
 	regulator-name = "vcc-touchscreen";
 	status = "okay";
 };

 &reg_rtc_ldo {
 	regulator-name = "vcc-rtc";
 };

 &simplefb_hdmi {
 	vcc-hdmi-supply = <&reg_dldo1>;
 };

 &hdmi {
 	hvcc-supply = <&reg_dldo1>;
 	status = "okay";
 };

 &hdmi_out {
 	hdmi_out_con: endpoint {
 		remote-endpoint = <&hdmi_con_in>;
 	};
 };

 &sound {
 	status = "okay";
 	simple-audio-card,aux-devs = <&codec_analog>, <&speaker_amp>;
 	simple-audio-card,widgets = "Microphone", "Internal Microphone Left",
 				    "Microphone", "Internal Microphone Right",
 				    "Headphone", "Headphone Jack",
 				    "Speaker", "Internal Speaker";
 	simple-audio-card,routing =
 			"Left DAC", "DACL",
 			"Right DAC", "DACR",
 			"Speaker Amp INL", "LINEOUT",
 			"Speaker Amp INR", "LINEOUT",
 			"Internal Speaker", "Speaker Amp OUTL",
 			"Internal Speaker", "Speaker Amp OUTR",
 			"Headphone Jack", "HP",
 			"ADCL", "Left ADC",
 			"ADCR", "Right ADC",
 			"Internal Microphone Left", "MBIAS",
 			"MIC1", "Internal Microphone Left",
 			"Internal Microphone Right", "HBIAS",
 			"MIC2", "Internal Microphone Right";
 };

 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pb_pins>;
 	status = "okay";
 };

 &usb_otg {
 	dr_mode = "otg";
 	status = "okay";
 };

 &usb_power_supply {
 	status = "okay";
 };

 &usbphy {
 	usb0_id_det-gpios = <&pio 7 9 GPIO_ACTIVE_HIGH>; /* PH9 */
 	usb0_vbus_power-supply = <&usb_power_supply>;
 	usb0_vbus-supply = <&reg_drivevbus>;
 	usb1_vbus-supply = <&reg_ldo_io0>;
 	status = "okay";
 };
	// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
	/*
	* Copyright (C) 2019 Icenowy Zheng <icenowy@aosc.xyz>
	*
	*/

	/dts-v1/;

	#include "sun50i-a64.dtsi"
	#include "sun50i-a64-cpu-opp.dtsi"

	#include <dt-bindings/gpio/gpio.h>
	#include <dt-bindings/input/input.h>
	#include <dt-bindings/pwm/pwm.h>

	/ {
	model = "PineTab, Development Sample";
	compatible = "pine64,pinetab", "allwinner,sun50i-a64";

	aliases {
	serial0 = &uart0;
	ethernet0 = &rtl8723cs;
	};

	backlight: backlight {
	compatible = "pwm-backlight";
	pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
	brightness-levels = <0 16 18 20 22 24 26 29 32 35 38 42 46 51 56 62 68 75 83 91 100>;
	default-brightness-level = <15>;
	enable-gpios = <&pio 3 23 GPIO_ACTIVE_HIGH>; /* PD23 */
	power-supply = <&vdd_bl>;
	};

	chosen {
	stdout-path = "serial0:115200n8";
	};

	hdmi-connector {
	compatible = "hdmi-connector";
	type = "c";

	port {
	hdmi_con_in: endpoint {
	remote-endpoint = <&hdmi_out_con>;
	};
	};
	};

	i2c-csi {
	compatible = "i2c-gpio";
	sda-gpios = <&pio 4 13 GPIO_ACTIVE_HIGH>; /* PE13 */
	scl-gpios = <&pio 4 12 GPIO_ACTIVE_HIGH>; /* PE12 */
	i2c-gpio,delay-us = <5>;
	#address-cells = <1>;
	#size-cells = <0>;

	/* Rear camera */
	ov5640: camera@3c {
	compatible = "ovti,ov5640";
	reg = <0x3c>;
	pinctrl-names = "default";
	pinctrl-0 = <&csi_mclk_pin>;
	clocks = <&ccu CLK_CSI_MCLK>;
	clock-names = "xclk";

	AVDD-supply = <&reg_dldo3>;
	DOVDD-supply = <&reg_aldo1>;
	DVDD-supply = <&reg_eldo3>;
	reset-gpios = <&pio 4 14 GPIO_ACTIVE_LOW>; /* PE14 */
	powerdown-gpios = <&pio 4 15 GPIO_ACTIVE_HIGH>; /* PE15 */

	port {
	ov5640_ep: endpoint {
	remote-endpoint = <&csi_ep>;
	bus-width = <8>;
	hsync-active = <1>; /* Active high */
	vsync-active = <0>; /* Active low */
	data-active = <1>; /* Active high */
	pclk-sample = <1>; /* Rising */
	};
	};
	};
	};

	speaker_amp: audio-amplifier {
	compatible = "simple-audio-amplifier";
	enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */
	sound-name-prefix = "Speaker Amp";
	};

	vdd_bl: regulator {
	compatible = "regulator-fixed";
	regulator-name = "bl-3v3";
	regulator-min-microvolt = <3300000>;
	regulator-max-microvolt = <3300000>;
	gpio = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */
	enable-active-high;
	};

	wifi_pwrseq: wifi_pwrseq {
	compatible = "mmc-pwrseq-simple";
	reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
	post-power-on-delay-ms = <200>;
	};
	};

	&codec {
	status = "okay";
	};

	&codec_analog {
	cpvdd-supply = <&reg_eldo1>;
	status = "okay";
	};

	&cpu0 {
	cpu-supply = <&reg_dcdc2>;
	};

	&cpu1 {
	cpu-supply = <&reg_dcdc2>;
	};

	&cpu2 {
	cpu-supply = <&reg_dcdc2>;
	};

	&cpu3 {
	cpu-supply = <&reg_dcdc2>;
	};

	&csi {
	status = "okay";

	port {
	csi_ep: endpoint {
	remote-endpoint = <&ov5640_ep>;
	bus-width = <8>;
	hsync-active = <1>; /* Active high */
	vsync-active = <0>; /* Active low */
	data-active = <1>; /* Active high */
	pclk-sample = <1>; /* Rising */
	};
	};
	};

	&dai {
	status = "okay";
	};

	&de {
	status = "okay";
	};

	&dphy {
	status = "okay";
	};

	&dsi {
	vcc-dsi-supply = <&reg_dldo1>;
	status = "okay";

	panel@0 {
	compatible = "feixin,k101-im2ba02";
	reg = <0>;
	avdd-supply = <&reg_dc1sw>;
	dvdd-supply = <&reg_dc1sw>;
	cvdd-supply = <&reg_ldo_io1>;
	reset-gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* PD24 */
	backlight = <&backlight>;
	};
	};

	&ehci0 {
	status = "okay";
	};

	&ehci1 {
	status = "okay";
	};

	&i2c0 {
	status = "okay";

	touchscreen@5d {
	compatible = "goodix,gt9271";
	reg = <0x5d>;
	interrupt-parent = <&pio>;
	interrupts = <7 4 IRQ_TYPE_LEVEL_HIGH>; /* PH4 */
	irq-gpios = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
	reset-gpios = <&pio 7 8 GPIO_ACTIVE_HIGH>; /* PH8 */
	AVDD28-supply = <&reg_ldo_io1>;
	};
	};

	&i2c0_pins {
	bias-pull-up;
	};

	&i2c1 {
	status = "okay";

	/* TODO: add Bochs BMA223 accelerometer here */
	};

	&lradc {
	vref-supply = <&reg_aldo3>;
	status = "okay";

	button-200 {
	label = "Volume Up";
	linux,code = <KEY_VOLUMEUP>;
	channel = <0>;
	voltage = <200000>;
	};

	button-400 {
	label = "Volume Down";
	linux,code = <KEY_VOLUMEDOWN>;
	channel = <0>;
	voltage = <400000>;
	};
	};

	&mixer1 {
	status = "okay";
	};

	&mmc0 {
	pinctrl-names = "default";
	pinctrl-0 = <&mmc0_pins>;
	vmmc-supply = <&reg_dcdc1>;
	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
	disable-wp;
	bus-width = <4>;
	status = "okay";
	};

	&mmc1 {
	pinctrl-names = "default";
	pinctrl-0 = <&mmc1_pins>;
	vmmc-supply = <&reg_dldo4>;
	vqmmc-supply = <&reg_eldo1>;
	mmc-pwrseq = <&wifi_pwrseq>;
	bus-width = <4>;
	non-removable;
	status = "okay";

	rtl8723cs: wifi@1 {
	reg = <1>;
	};
	};

	&mmc2 {
	pinctrl-names = "default";
	pinctrl-0 = <&mmc2_pins>;
	vmmc-supply = <&reg_dcdc1>;
	vqmmc-supply = <&reg_dcdc1>;
	bus-width = <8>;
	non-removable;
	cap-mmc-hw-reset;
	status = "okay";
	};

	&ohci0 {
	status = "okay";
	};

	&pwm {
	status = "okay";
	};

	&r_rsb {
	status = "okay";

	axp803: pmic@3a3 {
	compatible = "x-powers,axp803";
	reg = <0x3a3>;
	interrupt-parent = <&r_intc>;
	interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>;
	x-powers,drive-vbus-en;
	};
	};

	#include "axp803.dtsi"

	&ac_power_supply {
	status = "okay";
	};

	&battery_power_supply {
	status = "okay";
	};

	&reg_aldo1 {
	regulator-min-microvolt = <2800000>;
	regulator-max-microvolt = <2800000>;
	regulator-name = "dovdd-csi";
	};

	&reg_aldo2 {
	regulator-always-on;
	regulator-min-microvolt = <1800000>;
	regulator-max-microvolt = <3300000>;
	regulator-name = "vcc-pl";
	};

	&reg_aldo3 {
	regulator-always-on;
	regulator-min-microvolt = <2700000>;
	regulator-max-microvolt = <3300000>;
	regulator-name = "vcc-pll-avcc";
	};

	&reg_dc1sw {
	regulator-name = "vcc-lcd";
	};

	&reg_dcdc1 {
	regulator-always-on;
	regulator-min-microvolt = <3300000>;
	regulator-max-microvolt = <3300000>;
	regulator-name = "vcc-3v3";
	};

	&reg_dcdc2 {
	regulator-always-on;
	regulator-min-microvolt = <1000000>;
	regulator-max-microvolt = <1300000>;
	regulator-name = "vdd-cpux";
	};

	/* DCDC3 is polyphased with DCDC2 */

	&reg_dcdc5 {
	regulator-always-on;
	regulator-min-microvolt = <1200000>;
	regulator-max-microvolt = <1200000>;
	regulator-name = "vcc-dram";
	};

	&reg_dcdc6 {
	regulator-always-on;
	regulator-min-microvolt = <1100000>;
	regulator-max-microvolt = <1100000>;
	regulator-name = "vdd-sys";
	};

	&reg_dldo1 {
	regulator-always-on;
	regulator-min-microvolt = <3300000>;
	regulator-max-microvolt = <3300000>;
	regulator-name = "vcc-hdmi-dsi-sensor";
	};

	&reg_dldo3 {
	regulator-min-microvolt = <2800000>;
	regulator-max-microvolt = <2800000>;
	regulator-name = "avdd-csi";
	};

	&reg_dldo4 {
	regulator-min-microvolt = <3300000>;
	regulator-max-microvolt = <3300000>;
	regulator-name = "vcc-wifi";
	};

	&reg_drivevbus {
	regulator-name = "usb0-vbus";
	status = "okay";
	};

	&reg_eldo1 {
	regulator-always-on;
	regulator-min-microvolt = <1800000>;
	regulator-max-microvolt = <1800000>;
	regulator-name = "cpvdd";
	};

	&reg_eldo2 {
	regulator-min-microvolt = <1800000>;
	regulator-max-microvolt = <1800000>;
	regulator-name = "vcca-1v8";
	};

	&reg_eldo3 {
	regulator-min-microvolt = <1800000>;
	regulator-max-microvolt = <1800000>;
	regulator-name = "dvdd-1v8-csi";
	};

	&reg_fldo1 {
	regulator-min-microvolt = <1200000>;
	regulator-max-microvolt = <1200000>;
	regulator-name = "vcc-1v2-hsic";
	};

	&reg_fldo2 {
	regulator-always-on;
	regulator-min-microvolt = <1100000>;
	regulator-max-microvolt = <1100000>;
	regulator-name = "vdd-cpus";
	};

	&reg_ldo_io0 {
	regulator-min-microvolt = <3300000>;
	regulator-max-microvolt = <3300000>;
	regulator-name = "vcc-usb";
	status = "okay";
	};

	&reg_ldo_io1 {
	regulator-min-microvolt = <3300000>;
	regulator-max-microvolt = <3300000>;
	regulator-enable-ramp-delay = <3500000>;
	regulator-name = "vcc-touchscreen";
	status = "okay";
	};

	&reg_rtc_ldo {
	regulator-name = "vcc-rtc";
	};

	&simplefb_hdmi {
	vcc-hdmi-supply = <&reg_dldo1>;
	};

	&hdmi {
	hvcc-supply = <&reg_dldo1>;
	status = "okay";
	};

	&hdmi_out {
	hdmi_out_con: endpoint {
	remote-endpoint = <&hdmi_con_in>;
	};
	};

	&sound {
	status = "okay";
	simple-audio-card,aux-devs = <&codec_analog>, <&speaker_amp>;
	simple-audio-card,widgets = "Microphone", "Internal Microphone Left",
	"Microphone", "Internal Microphone Right",
	"Headphone", "Headphone Jack",
	"Speaker", "Internal Speaker";
	simple-audio-card,routing =
	"Left DAC", "DACL",
	"Right DAC", "DACR",
	"Speaker Amp INL", "LINEOUT",
	"Speaker Amp INR", "LINEOUT",
	"Internal Speaker", "Speaker Amp OUTL",
	"Internal Speaker", "Speaker Amp OUTR",
	"Headphone Jack", "HP",
	"ADCL", "Left ADC",
	"ADCR", "Right ADC",
	"Internal Microphone Left", "MBIAS",
	"MIC1", "Internal Microphone Left",
	"Internal Microphone Right", "HBIAS",
	"MIC2", "Internal Microphone Right";
	};

	&uart0 {
	pinctrl-names = "default";
	pinctrl-0 = <&uart0_pb_pins>;
	status = "okay";
	};

	&usb_otg {
	dr_mode = "otg";
	status = "okay";
	};

	&usb_power_supply {
	status = "okay";
	};

	&usbphy {
	usb0_id_det-gpios = <&pio 7 9 GPIO_ACTIVE_HIGH>; /* PH9 */
	usb0_vbus_power-supply = <&usb_power_supply>;
	usb0_vbus-supply = <&reg_drivevbus>;
	usb1_vbus-supply = <&reg_ldo_io0>;
	status = "okay";
	};