| # SPDX-License-Identifier: GPL-2.0-only |
| # |
| # Phy drivers for TI platforms |
| # |
| config PHY_DA8XX_USB |
| tristate "TI DA8xx USB PHY Driver" |
| depends on ARCH_DAVINCI_DA8XX || COMPILE_TEST |
| select GENERIC_PHY |
| select MFD_SYSCON |
| help |
| Enable this to support the USB PHY on DA8xx SoCs. |
| |
| This driver controls both the USB 1.1 PHY and the USB 2.0 PHY. |
| |
| config PHY_DM816X_USB |
| tristate "TI dm816x USB PHY driver" |
| depends on ARCH_OMAP2PLUS || COMPILE_TEST |
| depends on USB_SUPPORT |
| select GENERIC_PHY |
| select USB_PHY |
| help |
| Enable this for dm816x USB to work. |
| |
| config PHY_AM654_SERDES |
| tristate "TI AM654 SERDES support" |
| depends on OF && ARCH_K3 || COMPILE_TEST |
| depends on COMMON_CLK |
| select GENERIC_PHY |
| select MULTIPLEXER |
| select REGMAP_MMIO |
| select MUX_MMIO |
| help |
| This option enables support for TI AM654 SerDes PHY used for |
| PCIe. |
| |
| config PHY_J721E_WIZ |
| tristate "TI J721E WIZ (SERDES Wrapper) support" |
| depends on OF && ARCH_K3 || COMPILE_TEST |
| depends on HAS_IOMEM && OF_ADDRESS |
| depends on COMMON_CLK |
| select GENERIC_PHY |
| select MULTIPLEXER |
| select REGMAP_MMIO |
| select MUX_MMIO |
| help |
| This option enables support for WIZ module present in TI's J721E |
| SoC. WIZ is a serdes wrapper used to configure some of the input |
| signals to the SERDES (Sierra/Torrent). This driver configures |
| three clock selects (pll0, pll1, dig) and resets for each of the |
| lanes. |
| |
| config OMAP_CONTROL_PHY |
| tristate "OMAP CONTROL PHY Driver" |
| depends on ARCH_OMAP2PLUS || COMPILE_TEST |
| help |
| Enable this to add support for the PHY part present in the control |
| module. This driver has API to power on the USB2 PHY and to write to |
| the mailbox. The mailbox is present only in omap4 and the register to |
| power on the USB2 PHY is present in OMAP4 and OMAP5. OMAP5 has an |
| additional register to power on USB3 PHY/SATA PHY/PCIE PHY |
| (PIPE3 PHY). |
| |
| config OMAP_USB2 |
| tristate "OMAP USB2 PHY Driver" |
| depends on ARCH_OMAP2PLUS || ARCH_K3 |
| depends on USB_SUPPORT |
| select GENERIC_PHY |
| select USB_PHY |
| select OMAP_CONTROL_PHY if ARCH_OMAP2PLUS || COMPILE_TEST |
| help |
| Enable this to support the transceiver that is part of SOC. This |
| driver takes care of all the PHY functionality apart from comparator. |
| The USB OTG controller communicates with the comparator using this |
| driver. |
| |
| config TI_PIPE3 |
| tristate "TI PIPE3 PHY Driver" |
| depends on ARCH_OMAP2PLUS || COMPILE_TEST |
| select GENERIC_PHY |
| select OMAP_CONTROL_PHY |
| help |
| Enable this to support the PIPE3 PHY that is part of TI SOCs. This |
| driver takes care of all the PHY functionality apart from comparator. |
| This driver interacts with the "OMAP Control PHY Driver" to power |
| on/off the PHY. |
| |
| config PHY_TUSB1210 |
| tristate "TI TUSB1210 ULPI PHY module" |
| depends on USB_ULPI_BUS |
| select GENERIC_PHY |
| help |
| Support for TI TUSB1210 USB ULPI PHY. |
| |
| config TWL4030_USB |
| tristate "TWL4030 USB Transceiver Driver" |
| depends on TWL4030_CORE && REGULATOR_TWL4030 && USB_MUSB_OMAP2PLUS |
| depends on USB_SUPPORT |
| depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't 'y' |
| select GENERIC_PHY |
| select USB_PHY |
| help |
| Enable this to support the USB OTG transceiver on TWL4030 |
| family chips (including the TWL5030 and TPS659x0 devices). |
| This transceiver supports high and full speed devices plus, |
| in host mode, low speed. |
| |
| config PHY_TI_GMII_SEL |
| tristate |
| select GENERIC_PHY |
| select REGMAP |
| help |
| This driver supports configuring of the TI CPSW Port mode depending on |
| the Ethernet PHY connected to the CPSW Port. |
