| // SPDX-License-Identifier: GPL-2.0-only |
| /* |
| * Xilinx gpio driver for xps/axi_gpio IP. |
| * |
| * Copyright 2008 - 2013 Xilinx, Inc. |
| */ |
| |
| #include <linux/bitops.h> |
| #include <linux/init.h> |
| #include <linux/errno.h> |
| #include <linux/module.h> |
| #include <linux/of_device.h> |
| #include <linux/of_platform.h> |
| #include <linux/io.h> |
| #include <linux/gpio/driver.h> |
| #include <linux/slab.h> |
| |
| /* Register Offset Definitions */ |
| #define XGPIO_DATA_OFFSET (0x0) /* Data register */ |
| #define XGPIO_TRI_OFFSET (0x4) /* I/O direction register */ |
| |
| #define XGPIO_CHANNEL_OFFSET 0x8 |
| |
| /* Read/Write access to the GPIO registers */ |
| #if defined(CONFIG_ARCH_ZYNQ) || defined(CONFIG_X86) |
| # define xgpio_readreg(offset) readl(offset) |
| # define xgpio_writereg(offset, val) writel(val, offset) |
| #else |
| # define xgpio_readreg(offset) __raw_readl(offset) |
| # define xgpio_writereg(offset, val) __raw_writel(val, offset) |
| #endif |
| |
| /** |
| * struct xgpio_instance - Stores information about GPIO device |
| * @gc: GPIO chip |
| * @regs: register block |
| * @gpio_width: GPIO width for every channel |
| * @gpio_state: GPIO state shadow register |
| * @gpio_dir: GPIO direction shadow register |
| * @gpio_lock: Lock used for synchronization |
| */ |
| struct xgpio_instance { |
| struct gpio_chip gc; |
| void __iomem *regs; |
| unsigned int gpio_width[2]; |
| u32 gpio_state[2]; |
| u32 gpio_dir[2]; |
| spinlock_t gpio_lock[2]; |
| }; |
| |
| static inline int xgpio_index(struct xgpio_instance *chip, int gpio) |
| { |
| if (gpio >= chip->gpio_width[0]) |
| return 1; |
| |
| return 0; |
| } |
| |
| static inline int xgpio_regoffset(struct xgpio_instance *chip, int gpio) |
| { |
| if (xgpio_index(chip, gpio)) |
| return XGPIO_CHANNEL_OFFSET; |
| |
| return 0; |
| } |
| |
| static inline int xgpio_offset(struct xgpio_instance *chip, int gpio) |
| { |
| if (xgpio_index(chip, gpio)) |
| return gpio - chip->gpio_width[0]; |
| |
| return gpio; |
| } |
| |
| /** |
| * xgpio_get - Read the specified signal of the GPIO device. |
| * @gc: Pointer to gpio_chip device structure. |
| * @gpio: GPIO signal number. |
| * |
| * This function reads the specified signal of the GPIO device. |
| * |
| * Return: |
| * 0 if direction of GPIO signals is set as input otherwise it |
| * returns negative error value. |
| */ |
| static int xgpio_get(struct gpio_chip *gc, unsigned int gpio) |
| { |
| struct xgpio_instance *chip = gpiochip_get_data(gc); |
| u32 val; |
| |
| val = xgpio_readreg(chip->regs + XGPIO_DATA_OFFSET + |
| xgpio_regoffset(chip, gpio)); |
| |
| return !!(val & BIT(xgpio_offset(chip, gpio))); |
| } |
| |
| /** |
| * xgpio_set - Write the specified signal of the GPIO device. |
| * @gc: Pointer to gpio_chip device structure. |
| * @gpio: GPIO signal number. |
| * @val: Value to be written to specified signal. |
| * |
| * This function writes the specified value in to the specified signal of the |
| * GPIO device. |
| */ |
| static void xgpio_set(struct gpio_chip *gc, unsigned int gpio, int val) |
| { |
| unsigned long flags; |
| struct xgpio_instance *chip = gpiochip_get_data(gc); |
| int index = xgpio_index(chip, gpio); |
| int offset = xgpio_offset(chip, gpio); |
| |
| spin_lock_irqsave(&chip->gpio_lock[index], flags); |
| |
| /* Write to GPIO signal and set its direction to output */ |
| if (val) |
| chip->gpio_state[index] |= BIT(offset); |
| else |
| chip->gpio_state[index] &= ~BIT(offset); |
| |
| xgpio_writereg(chip->regs + XGPIO_DATA_OFFSET + |
| xgpio_regoffset(chip, gpio), chip->gpio_state[index]); |
| |
| spin_unlock_irqrestore(&chip->gpio_lock[index], flags); |
| } |
| |
| /** |
| * xgpio_set_multiple - Write the specified signals of the GPIO device. |
| * @gc: Pointer to gpio_chip device structure. |
| * @mask: Mask of the GPIOS to modify. |
| * @bits: Value to be wrote on each GPIO |
| * |
| * This function writes the specified values into the specified signals of the |
| * GPIO devices. |
| */ |
| static void xgpio_set_multiple(struct gpio_chip *gc, unsigned long *mask, |
| unsigned long *bits) |
| { |
| unsigned long flags; |
| struct xgpio_instance *chip = gpiochip_get_data(gc); |
| int index = xgpio_index(chip, 0); |
| int offset, i; |
| |
| spin_lock_irqsave(&chip->gpio_lock[index], flags); |
| |
| /* Write to GPIO signals */ |
| for (i = 0; i < gc->ngpio; i++) { |
| if (*mask == 0) |
| break; |
| /* Once finished with an index write it out to the register */ |
| if (index != xgpio_index(chip, i)) { |
| xgpio_writereg(chip->regs + XGPIO_DATA_OFFSET + |
| index * XGPIO_CHANNEL_OFFSET, |
| chip->gpio_state[index]); |
| spin_unlock_irqrestore(&chip->gpio_lock[index], flags); |
| index = xgpio_index(chip, i); |
| spin_lock_irqsave(&chip->gpio_lock[index], flags); |
| } |
| if (__test_and_clear_bit(i, mask)) { |
| offset = xgpio_offset(chip, i); |
| if (test_bit(i, bits)) |
| chip->gpio_state[index] |= BIT(offset); |
| else |
| chip->gpio_state[index] &= ~BIT(offset); |
| } |
| } |
| |
| xgpio_writereg(chip->regs + XGPIO_DATA_OFFSET + |
| index * XGPIO_CHANNEL_OFFSET, chip->gpio_state[index]); |
| |
| spin_unlock_irqrestore(&chip->gpio_lock[index], flags); |
| } |
| |
| /** |
| * xgpio_dir_in - Set the direction of the specified GPIO signal as input. |
| * @gc: Pointer to gpio_chip device structure. |
| * @gpio: GPIO signal number. |
| * |
| * Return: |
| * 0 - if direction of GPIO signals is set as input |
| * otherwise it returns negative error value. |
| */ |
| static int xgpio_dir_in(struct gpio_chip *gc, unsigned int gpio) |
| { |
| unsigned long flags; |
| struct xgpio_instance *chip = gpiochip_get_data(gc); |
| int index = xgpio_index(chip, gpio); |
| int offset = xgpio_offset(chip, gpio); |
| |
| spin_lock_irqsave(&chip->gpio_lock[index], flags); |
| |
| /* Set the GPIO bit in shadow register and set direction as input */ |
| chip->gpio_dir[index] |= BIT(offset); |
| xgpio_writereg(chip->regs + XGPIO_TRI_OFFSET + |
| xgpio_regoffset(chip, gpio), chip->gpio_dir[index]); |
| |
| spin_unlock_irqrestore(&chip->gpio_lock[index], flags); |
| |
| return 0; |
| } |
| |
| /** |
| * xgpio_dir_out - Set the direction of the specified GPIO signal as output. |
| * @gc: Pointer to gpio_chip device structure. |
| * @gpio: GPIO signal number. |
| * @val: Value to be written to specified signal. |
| * |
| * This function sets the direction of specified GPIO signal as output. |
| * |
| * Return: |
| * If all GPIO signals of GPIO chip is configured as input then it returns |
| * error otherwise it returns 0. |
| */ |
| static int xgpio_dir_out(struct gpio_chip *gc, unsigned int gpio, int val) |
| { |
| unsigned long flags; |
| struct xgpio_instance *chip = gpiochip_get_data(gc); |
| int index = xgpio_index(chip, gpio); |
| int offset = xgpio_offset(chip, gpio); |
| |
| spin_lock_irqsave(&chip->gpio_lock[index], flags); |
| |
| /* Write state of GPIO signal */ |
| if (val) |
| chip->gpio_state[index] |= BIT(offset); |
| else |
| chip->gpio_state[index] &= ~BIT(offset); |
| xgpio_writereg(chip->regs + XGPIO_DATA_OFFSET + |
| xgpio_regoffset(chip, gpio), chip->gpio_state[index]); |
| |
| /* Clear the GPIO bit in shadow register and set direction as output */ |
| chip->gpio_dir[index] &= ~BIT(offset); |
| xgpio_writereg(chip->regs + XGPIO_TRI_OFFSET + |
| xgpio_regoffset(chip, gpio), chip->gpio_dir[index]); |
| |
| spin_unlock_irqrestore(&chip->gpio_lock[index], flags); |
| |
| return 0; |
| } |
| |
| /** |
| * xgpio_save_regs - Set initial values of GPIO pins |
| * @chip: Pointer to GPIO instance |
| */ |
| static void xgpio_save_regs(struct xgpio_instance *chip) |
| { |
| xgpio_writereg(chip->regs + XGPIO_DATA_OFFSET, chip->gpio_state[0]); |
| xgpio_writereg(chip->regs + XGPIO_TRI_OFFSET, chip->gpio_dir[0]); |
| |
| if (!chip->gpio_width[1]) |
| return; |
| |
| xgpio_writereg(chip->regs + XGPIO_DATA_OFFSET + XGPIO_CHANNEL_OFFSET, |
| chip->gpio_state[1]); |
| xgpio_writereg(chip->regs + XGPIO_TRI_OFFSET + XGPIO_CHANNEL_OFFSET, |
| chip->gpio_dir[1]); |
| } |
| |
| /** |
| * xgpio_of_probe - Probe method for the GPIO device. |
| * @pdev: pointer to the platform device |
| * |
| * Return: |
| * It returns 0, if the driver is bound to the GPIO device, or |
| * a negative value if there is an error. |
| */ |
| static int xgpio_probe(struct platform_device *pdev) |
| { |
| struct xgpio_instance *chip; |
| int status = 0; |
| struct device_node *np = pdev->dev.of_node; |
| u32 is_dual; |
| |
| chip = devm_kzalloc(&pdev->dev, sizeof(*chip), GFP_KERNEL); |
| if (!chip) |
| return -ENOMEM; |
| |
| platform_set_drvdata(pdev, chip); |
| |
| /* Update GPIO state shadow register with default value */ |
| of_property_read_u32(np, "xlnx,dout-default", &chip->gpio_state[0]); |
| |
| /* Update GPIO direction shadow register with default value */ |
| if (of_property_read_u32(np, "xlnx,tri-default", &chip->gpio_dir[0])) |
| chip->gpio_dir[0] = 0xFFFFFFFF; |
| |
| /* |
| * Check device node and parent device node for device width |
| * and assume default width of 32 |
| */ |
| if (of_property_read_u32(np, "xlnx,gpio-width", &chip->gpio_width[0])) |
| chip->gpio_width[0] = 32; |
| |
| spin_lock_init(&chip->gpio_lock[0]); |
| |
| if (of_property_read_u32(np, "xlnx,is-dual", &is_dual)) |
| is_dual = 0; |
| |
| if (is_dual) { |
| /* Update GPIO state shadow register with default value */ |
| of_property_read_u32(np, "xlnx,dout-default-2", |
| &chip->gpio_state[1]); |
| |
| /* Update GPIO direction shadow register with default value */ |
| if (of_property_read_u32(np, "xlnx,tri-default-2", |
| &chip->gpio_dir[1])) |
| chip->gpio_dir[1] = 0xFFFFFFFF; |
| |
| /* |
| * Check device node and parent device node for device width |
| * and assume default width of 32 |
| */ |
| if (of_property_read_u32(np, "xlnx,gpio2-width", |
| &chip->gpio_width[1])) |
| chip->gpio_width[1] = 32; |
| |
| spin_lock_init(&chip->gpio_lock[1]); |
| } |
| |
| chip->gc.base = -1; |
| chip->gc.ngpio = chip->gpio_width[0] + chip->gpio_width[1]; |
| chip->gc.parent = &pdev->dev; |
| chip->gc.direction_input = xgpio_dir_in; |
| chip->gc.direction_output = xgpio_dir_out; |
| chip->gc.get = xgpio_get; |
| chip->gc.set = xgpio_set; |
| chip->gc.set_multiple = xgpio_set_multiple; |
| |
| chip->gc.label = dev_name(&pdev->dev); |
| |
| chip->regs = devm_platform_ioremap_resource(pdev, 0); |
| if (IS_ERR(chip->regs)) { |
| dev_err(&pdev->dev, "failed to ioremap memory resource\n"); |
| return PTR_ERR(chip->regs); |
| } |
| |
| xgpio_save_regs(chip); |
| |
| status = devm_gpiochip_add_data(&pdev->dev, &chip->gc, chip); |
| if (status) { |
| dev_err(&pdev->dev, "failed to add GPIO chip\n"); |
| return status; |
| } |
| |
| return 0; |
| } |
| |
| static const struct of_device_id xgpio_of_match[] = { |
| { .compatible = "xlnx,xps-gpio-1.00.a", }, |
| { /* end of list */ }, |
| }; |
| |
| MODULE_DEVICE_TABLE(of, xgpio_of_match); |
| |
| static struct platform_driver xgpio_plat_driver = { |
| .probe = xgpio_probe, |
| .driver = { |
| .name = "gpio-xilinx", |
| .of_match_table = xgpio_of_match, |
| }, |
| }; |
| |
| static int __init xgpio_init(void) |
| { |
| return platform_driver_register(&xgpio_plat_driver); |
| } |
| |
| subsys_initcall(xgpio_init); |
| |
| static void __exit xgpio_exit(void) |
| { |
| platform_driver_unregister(&xgpio_plat_driver); |
| } |
| module_exit(xgpio_exit); |
| |
| MODULE_AUTHOR("Xilinx, Inc."); |
| MODULE_DESCRIPTION("Xilinx GPIO driver"); |
| MODULE_LICENSE("GPL"); |