blob: b7e664f7395b33405bff1cb181e79fe38aeb378a [file] [log] [blame]
# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/usb/ci-hdrc-usb2.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: USB2 ChipIdea USB controller
maintainers:
- Xu Yang <xu.yang_2@nxp.com>
- Peng Fan <peng.fan@nxp.com>
properties:
compatible:
oneOf:
- enum:
- chipidea,usb2
- fsl,imx27-usb
- lsi,zevio-usb
- nuvoton,npcm750-udc
- nvidia,tegra20-ehci
- nvidia,tegra20-udc
- nvidia,tegra30-ehci
- nvidia,tegra30-udc
- nvidia,tegra114-udc
- nvidia,tegra124-udc
- qcom,ci-hdrc
- items:
- enum:
- nvidia,tegra114-ehci
- nvidia,tegra124-ehci
- nvidia,tegra210-ehci
- const: nvidia,tegra30-ehci
- items:
- enum:
- fsl,imx23-usb
- fsl,imx25-usb
- fsl,imx28-usb
- fsl,imx35-usb
- fsl,imx50-usb
- fsl,imx51-usb
- fsl,imx53-usb
- fsl,imx6q-usb
- fsl,imx6sl-usb
- fsl,imx6sx-usb
- fsl,imx6ul-usb
- fsl,imx7d-usb
- fsl,vf610-usb
- const: fsl,imx27-usb
- items:
- enum:
- fsl,imx8dxl-usb
- fsl,imx8ulp-usb
- const: fsl,imx7ulp-usb
- const: fsl,imx6ul-usb
- items:
- enum:
- fsl,imx8mm-usb
- fsl,imx8mn-usb
- const: fsl,imx7d-usb
- const: fsl,imx27-usb
- items:
- enum:
- fsl,imx6sll-usb
- fsl,imx7ulp-usb
- const: fsl,imx6ul-usb
- const: fsl,imx27-usb
- items:
- const: xlnx,zynq-usb-2.20a
- const: chipidea,usb2
- items:
- enum:
- nuvoton,npcm845-udc
- const: nuvoton,npcm750-udc
reg:
minItems: 1
maxItems: 2
interrupts:
minItems: 1
maxItems: 2
clocks:
minItems: 1
maxItems: 3
clock-names:
minItems: 1
maxItems: 3
dr_mode: true
power-domains:
maxItems: 1
resets:
maxItems: 1
reset-names:
maxItems: 1
"#reset-cells":
const: 1
phy_type: true
itc-setting:
description:
interrupt threshold control register control, the setting should be
aligned with ITC bits at register USBCMD.
$ref: /schemas/types.yaml#/definitions/uint32
ahb-burst-config:
description:
it is vendor dependent, the required value should be aligned with
AHBBRST at SBUSCFG, the range is from 0x0 to 0x7. This property is
used to change AHB burst configuration, check the chipidea spec for
meaning of each value. If this property is not existed, it will use
the reset value.
$ref: /schemas/types.yaml#/definitions/uint32
minimum: 0x0
maximum: 0x7
tx-burst-size-dword:
description:
it is vendor dependent, the tx burst size in dword (4 bytes), This
register represents the maximum length of a the burst in 32-bit
words while moving data from system memory to the USB bus, the value
of this property will only take effect if property "ahb-burst-config"
is set to 0, if this property is missing the reset default of the
hardware implementation will be used.
$ref: /schemas/types.yaml#/definitions/uint32
minimum: 0x0
maximum: 0x20
rx-burst-size-dword:
description:
it is vendor dependent, the rx burst size in dword (4 bytes), This
register represents the maximum length of a the burst in 32-bit words
while moving data from the USB bus to system memory, the value of
this property will only take effect if property "ahb-burst-config"
is set to 0, if this property is missing the reset default of the
hardware implementation will be used.
$ref: /schemas/types.yaml#/definitions/uint32
minimum: 0x0
maximum: 0x20
extcon:
description:
Phandles to external connector devices. First phandle should point
to external connector, which provide "USB" cable events, the second
should point to external connector device, which provide "USB-HOST"
cable events. If one of the external connector devices is not
required, empty <0> phandle should be specified.
$ref: /schemas/types.yaml#/definitions/phandle-array
minItems: 1
items:
- description: vbus extcon
- description: id extcon
phy-clkgate-delay-us:
description:
The delay time (us) between putting the PHY into low power mode and
gating the PHY clock.
non-zero-ttctrl-ttha:
description:
After setting this property, the value of register ttctrl.ttha
will be 0x7f; if not, the value will be 0x0, this is the default
value. It needs to be very carefully for setting this property, it
is recommended that consult with your IC engineer before setting
this value. On the most of chipidea platforms, the "usage_tt" flag
at RTL is 0, so this property only affects siTD.
If this property is not set, the max packet size is 1023 bytes, and
if the total of packet size for previous transactions are more than
256 bytes, it can't accept any transactions within this frame. The
use case is single transaction, but higher frame rate.
If this property is set, the max packet size is 188 bytes, it can
handle more transactions than above case, it can accept transactions
until it considers the left room size within frame is less than 188
bytes, software needs to make sure it does not send more than 90%
maximum_periodic_data_per_frame. The use case is multiple
transactions, but less frame rate.
type: boolean
mux-controls:
description:
The mux control for toggling host/device output of this controller.
It's expected that a mux state of 0 indicates device mode and a mux
state of 1 indicates host mode.
maxItems: 1
mux-control-names:
const: usb_switch
operating-points-v2:
description: A phandle to the OPP table containing the performance states.
$ref: /schemas/types.yaml#/definitions/phandle
pinctrl-names:
description:
Names for optional pin modes in "default", "host", "device".
In case of HSIC-mode, "idle" and "active" pin modes are mandatory.
In this case, the "idle" state needs to pull down the data and
strobe pin and the "active" state needs to pull up the strobe pin.
oneOf:
- items:
- const: idle
- const: active
- items:
- const: default
- enum:
- host
- device
- items:
- const: default
pinctrl-0:
maxItems: 1
pinctrl-1:
maxItems: 1
phys:
maxItems: 1
phy-names:
const: usb-phy
phy-select:
description:
Phandler of TCSR node with two argument that indicate register
offset, and phy index
$ref: /schemas/types.yaml#/definitions/phandle-array
items:
- description: phandle to TCSR node
- description: register offset
- description: phy index
vbus-supply:
description: reference to the VBUS regulator.
fsl,usbmisc:
description:
Phandler of non-core register device, with one argument that
indicate usb controller index
$ref: /schemas/types.yaml#/definitions/phandle-array
items:
- items:
- description: phandle to usbmisc node
- description: index of usb controller
fsl,anatop:
description: phandle for the anatop node.
$ref: /schemas/types.yaml#/definitions/phandle
disable-over-current:
type: boolean
description: disable over current detect
over-current-active-low:
type: boolean
description: over current signal polarity is active low
over-current-active-high:
type: boolean
description:
Over current signal polarity is active high. It's recommended to
specify the over current polarity.
power-active-high:
type: boolean
description: power signal polarity is active high
external-vbus-divider:
type: boolean
description: enables off-chip resistor divider for Vbus
samsung,picophy-pre-emp-curr-control:
description:
HS Transmitter Pre-Emphasis Current Control. This signal controls
the amount of current sourced to the USB_OTG*_DP and USB_OTG*_DN
pins after a J-to-K or K-to-J transition. The range is from 0x0 to
0x3, the default value is 0x1. Details can refer to TXPREEMPAMPTUNE0
bits of USBNC_n_PHY_CFG1.
$ref: /schemas/types.yaml#/definitions/uint32
minimum: 0x0
maximum: 0x3
samsung,picophy-dc-vol-level-adjust:
description:
HS DC Voltage Level Adjustment. Adjust the high-speed transmitter DC
level voltage. The range is from 0x0 to 0xf, the default value is
0x3. Details can refer to TXVREFTUNE0 bits of USBNC_n_PHY_CFG1.
$ref: /schemas/types.yaml#/definitions/uint32
minimum: 0x0
maximum: 0xf
fsl,picophy-rise-fall-time-adjust:
description:
HS Transmitter Rise/Fall Time Adjustment. Adjust the rise/fall times
of the high-speed transmitter waveform. It has no unit. The rise/fall
time will be increased or decreased by a certain percentage relative
to design default time. (0:-10%; 1:design default; 2:+15%; 3:+20%)
Details can refer to TXRISETUNE0 bit of USBNC_n_PHY_CFG1.
$ref: /schemas/types.yaml#/definitions/uint32
minimum: 0
maximum: 3
default: 1
usb-phy:
description: phandle for the PHY device. Use "phys" instead.
$ref: /schemas/types.yaml#/definitions/phandle
deprecated: true
fsl,usbphy:
description: phandle of usb phy that connects to the port. Use "phys" instead.
$ref: /schemas/types.yaml#/definitions/phandle
deprecated: true
nvidia,phy:
description: phandle of usb phy that connects to the port. Use "phys" instead.
$ref: /schemas/types.yaml#/definitions/phandle
deprecated: true
nvidia,needs-double-reset:
description: Indicates double reset or not.
type: boolean
deprecated: true
port:
description:
Any connector to the data bus of this controller should be modelled
using the OF graph bindings specified, if the "usb-role-switch"
property is used.
$ref: /schemas/graph.yaml#/properties/port
reset-gpios:
maxItems: 1
ulpi:
type: object
additionalProperties: false
patternProperties:
"^phy(-[0-9])?$":
description: The phy child node for Qcom chips.
type: object
$ref: /schemas/phy/qcom,usb-hs-phy.yaml
dependencies:
port: [ usb-role-switch ]
mux-controls: [ mux-control-names ]
required:
- compatible
- reg
- interrupts
allOf:
- $ref: usb-hcd.yaml#
- $ref: usb-drd.yaml#
- if:
properties:
phy_type:
const: hsic
required:
- phy_type
then:
properties:
pinctrl-names:
items:
- const: idle
- const: active
else:
properties:
pinctrl-names:
minItems: 1
maxItems: 2
oneOf:
- items:
- const: default
- enum:
- host
- device
- items:
- const: default
- if:
properties:
compatible:
contains:
enum:
- chipidea,usb2
- lsi,zevio-usb
- nuvoton,npcm750-udc
- nvidia,tegra20-udc
- nvidia,tegra30-udc
- nvidia,tegra114-udc
- nvidia,tegra124-udc
- qcom,ci-hdrc
- xlnx,zynq-usb-2.20a
then:
properties:
fsl,usbmisc: false
disable-over-current: false
over-current-active-low: false
over-current-active-high: false
power-active-high: false
external-vbus-divider: false
samsung,picophy-pre-emp-curr-control: false
samsung,picophy-dc-vol-level-adjust: false
unevaluatedProperties: false
examples:
- |
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/berlin2.h>
usb@f7ed0000 {
compatible = "chipidea,usb2";
reg = <0xf7ed0000 0x10000>;
interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&chip CLKID_USB0>;
phys = <&usb_phy0>;
phy-names = "usb-phy";
vbus-supply = <&reg_usb0_vbus>;
itc-setting = <0x4>; /* 4 micro-frames */
/* Incremental burst of unspecified length */
ahb-burst-config = <0x0>;
tx-burst-size-dword = <0x10>; /* 64 bytes */
rx-burst-size-dword = <0x10>;
extcon = <0>, <&usb_id>;
phy-clkgate-delay-us = <400>;
mux-controls = <&usb_switch>;
mux-control-names = "usb_switch";
};
# Example for HSIC:
- |
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/imx6qdl-clock.h>
usb@2184400 {
compatible = "fsl,imx6q-usb", "fsl,imx27-usb";
reg = <0x02184400 0x200>;
interrupts = <0 41 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clks IMX6QDL_CLK_USBOH3>;
fsl,usbphy = <&usbphynop1>;
fsl,usbmisc = <&usbmisc 2>;
phy_type = "hsic";
dr_mode = "host";
ahb-burst-config = <0x0>;
tx-burst-size-dword = <0x10>;
rx-burst-size-dword = <0x10>;
pinctrl-names = "idle", "active";
pinctrl-0 = <&pinctrl_usbh2_idle>;
pinctrl-1 = <&pinctrl_usbh2_active>;
#address-cells = <1>;
#size-cells = <0>;
ethernet@1 {
compatible = "usb424,9730";
reg = <1>;
};
};
...