| // SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| /* |
| * Copyright 2023 Gateworks Corporation |
| */ |
| |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/input/linux-event-codes.h> |
| #include <dt-bindings/net/ti-dp83867.h> |
| |
| / { |
| aliases { |
| ethernet0 = &eqos; |
| }; |
| |
| memory@40000000 { |
| device_type = "memory"; |
| reg = <0x0 0x40000000 0 0x80000000>; |
| }; |
| |
| gpio-keys { |
| compatible = "gpio-keys"; |
| |
| key-user-pb { |
| label = "user_pb"; |
| gpios = <&gpio 2 GPIO_ACTIVE_LOW>; |
| linux,code = <BTN_0>; |
| }; |
| |
| key-user-pb1x { |
| label = "user_pb1x"; |
| linux,code = <BTN_1>; |
| interrupt-parent = <&gsc>; |
| interrupts = <0>; |
| }; |
| |
| key-erased { |
| label = "key_erased"; |
| linux,code = <BTN_2>; |
| interrupt-parent = <&gsc>; |
| interrupts = <1>; |
| }; |
| |
| key-eeprom-wp { |
| label = "eeprom_wp"; |
| linux,code = <BTN_3>; |
| interrupt-parent = <&gsc>; |
| interrupts = <2>; |
| }; |
| |
| key-tamper { |
| label = "tamper"; |
| linux,code = <BTN_4>; |
| interrupt-parent = <&gsc>; |
| interrupts = <5>; |
| }; |
| |
| switch-hold { |
| label = "switch_hold"; |
| linux,code = <BTN_5>; |
| interrupt-parent = <&gsc>; |
| interrupts = <7>; |
| }; |
| }; |
| }; |
| |
| &A53_0 { |
| cpu-supply = <&buck3_reg>; |
| }; |
| |
| &A53_1 { |
| cpu-supply = <&buck3_reg>; |
| }; |
| |
| &A53_2 { |
| cpu-supply = <&buck3_reg>; |
| }; |
| |
| &A53_3 { |
| cpu-supply = <&buck3_reg>; |
| }; |
| |
| &eqos { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_eqos>; |
| phy-mode = "rgmii-id"; |
| phy-handle = <ðphy0>; |
| status = "okay"; |
| |
| mdio { |
| compatible = "snps,dwmac-mdio"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| ethphy0: ethernet-phy@0 { |
| compatible = "ethernet-phy-ieee802.3-c22"; |
| pinctrl-0 = <&pinctrl_ethphy0>; |
| pinctrl-names = "default"; |
| reg = <0x0>; |
| interrupt-parent = <&gpio3>; |
| interrupts = <16 IRQ_TYPE_EDGE_FALLING>; |
| ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>; |
| ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>; |
| tx-fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; |
| rx-fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; |
| }; |
| }; |
| }; |
| |
| &i2c1 { |
| clock-frequency = <100000>; |
| pinctrl-names = "default", "gpio"; |
| pinctrl-0 = <&pinctrl_i2c1>; |
| pinctrl-1 = <&pinctrl_i2c1_gpio>; |
| scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| status = "okay"; |
| |
| gsc: gsc@20 { |
| compatible = "gw,gsc"; |
| reg = <0x20>; |
| pinctrl-0 = <&pinctrl_gsc>; |
| interrupt-parent = <&gpio2>; |
| interrupts = <6 IRQ_TYPE_EDGE_FALLING>; |
| interrupt-controller; |
| #interrupt-cells = <1>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| adc { |
| compatible = "gw,gsc-adc"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| channel@6 { |
| gw,mode = <0>; |
| reg = <0x06>; |
| label = "temp"; |
| }; |
| |
| channel@8 { |
| gw,mode = <3>; |
| reg = <0x08>; |
| label = "vdd_bat"; |
| }; |
| |
| channel@16 { |
| gw,mode = <4>; |
| reg = <0x16>; |
| label = "fan_tach"; |
| }; |
| |
| channel@82 { |
| gw,mode = <2>; |
| reg = <0x82>; |
| label = "vdd_vin"; |
| gw,voltage-divider-ohms = <22100 1000>; |
| }; |
| |
| channel@84 { |
| gw,mode = <2>; |
| reg = <0x84>; |
| label = "vdd_adc1"; |
| gw,voltage-divider-ohms = <10000 10000>; |
| }; |
| |
| channel@86 { |
| gw,mode = <2>; |
| reg = <0x86>; |
| label = "vdd_adc2"; |
| gw,voltage-divider-ohms = <10000 10000>; |
| }; |
| |
| channel@88 { |
| gw,mode = <2>; |
| reg = <0x88>; |
| label = "vdd_1p0"; |
| }; |
| |
| channel@8c { |
| gw,mode = <2>; |
| reg = <0x8c>; |
| label = "vdd_1p8"; |
| }; |
| |
| channel@8e { |
| gw,mode = <2>; |
| reg = <0x8e>; |
| label = "vdd_2p5"; |
| }; |
| |
| channel@90 { |
| gw,mode = <2>; |
| reg = <0x90>; |
| label = "vdd_3p3"; |
| gw,voltage-divider-ohms = <10000 10000>; |
| }; |
| |
| channel@92 { |
| gw,mode = <2>; |
| reg = <0x92>; |
| label = "vdd_dram"; |
| }; |
| |
| channel@98 { |
| gw,mode = <2>; |
| reg = <0x98>; |
| label = "vdd_soc"; |
| }; |
| |
| channel@9a { |
| gw,mode = <2>; |
| reg = <0x9a>; |
| label = "vdd_arm"; |
| }; |
| |
| channel@a2 { |
| gw,mode = <2>; |
| reg = <0xa2>; |
| label = "vdd_gsc"; |
| gw,voltage-divider-ohms = <10000 10000>; |
| }; |
| }; |
| |
| fan-controller@0 { |
| compatible = "gw,gsc-fan"; |
| reg = <0x0a>; |
| }; |
| }; |
| |
| gpio: gpio@23 { |
| compatible = "nxp,pca9555"; |
| reg = <0x23>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-parent = <&gsc>; |
| interrupts = <4>; |
| }; |
| |
| eeprom@50 { |
| compatible = "atmel,24c02"; |
| reg = <0x50>; |
| pagesize = <16>; |
| }; |
| |
| eeprom@51 { |
| compatible = "atmel,24c02"; |
| reg = <0x51>; |
| pagesize = <16>; |
| }; |
| |
| eeprom@52 { |
| compatible = "atmel,24c02"; |
| reg = <0x52>; |
| pagesize = <16>; |
| }; |
| |
| eeprom@53 { |
| compatible = "atmel,24c02"; |
| reg = <0x53>; |
| pagesize = <16>; |
| }; |
| |
| rtc@68 { |
| compatible = "dallas,ds1672"; |
| reg = <0x68>; |
| }; |
| |
| pmic@69 { |
| compatible = "mps,mp5416"; |
| reg = <0x69>; |
| |
| regulators { |
| /* vdd_soc */ |
| buck1 { |
| regulator-name = "buck1"; |
| regulator-min-microvolt = <850000>; |
| regulator-max-microvolt = <1000000>; |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| /* vdd_dram */ |
| buck2 { |
| regulator-name = "buck2"; |
| regulator-min-microvolt = <1100000>; |
| regulator-max-microvolt = <1100000>; |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| /* vdd_arm */ |
| buck3_reg: buck3 { |
| regulator-name = "buck3"; |
| regulator-min-microvolt = <850000>; |
| regulator-max-microvolt = <1000000>; |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| /* vdd_1p8 */ |
| buck4 { |
| regulator-name = "buck4"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| /* OUT2: nvcc_snvs_1p8 */ |
| ldo1 { |
| regulator-name = "ldo1"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| /* OUT3: vdd_1p0 */ |
| ldo2 { |
| regulator-name = "ldo2"; |
| regulator-min-microvolt = <1000000>; |
| regulator-max-microvolt = <1000000>; |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| /* OUT4: vdd_2p5 */ |
| ldo3 { |
| regulator-name = "ldo3"; |
| regulator-min-microvolt = <2500000>; |
| regulator-max-microvolt = <2500000>; |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| /* OUT5: vdd_3p3 */ |
| ldo4 { |
| regulator-name = "ldo4"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| }; |
| }; |
| }; |
| |
| /* off-board header */ |
| &i2c2 { |
| clock-frequency = <400000>; |
| pinctrl-names = "default", "gpio"; |
| pinctrl-0 = <&pinctrl_i2c2>; |
| pinctrl-1 = <&pinctrl_i2c2_gpio>; |
| scl-gpios = <&gpio5 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| sda-gpios = <&gpio5 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| status = "okay"; |
| |
| eeprom@52 { |
| compatible = "atmel,24c32"; |
| reg = <0x52>; |
| pagesize = <32>; |
| }; |
| }; |
| |
| /* off-board header */ |
| &i2c3 { |
| clock-frequency = <400000>; |
| pinctrl-names = "default", "gpio"; |
| pinctrl-0 = <&pinctrl_i2c3>; |
| pinctrl-1 = <&pinctrl_i2c3_gpio>; |
| scl-gpios = <&gpio5 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| sda-gpios = <&gpio5 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| status = "okay"; |
| }; |
| |
| /* off-board header */ |
| &uart1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart1>; |
| status = "okay"; |
| }; |
| |
| /* console */ |
| &uart2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart2>; |
| status = "okay"; |
| }; |
| |
| /* off-board header */ |
| &uart3 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart3>; |
| status = "okay"; |
| }; |
| |
| /* off-board */ |
| &usdhc1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usdhc1>; |
| bus-width = <4>; |
| non-removable; |
| status = "okay"; |
| bus-width = <4>; |
| non-removable; |
| status = "okay"; |
| }; |
| |
| /* eMMC */ |
| &usdhc3 { |
| pinctrl-names = "default", "state_100mhz", "state_200mhz"; |
| pinctrl-0 = <&pinctrl_usdhc3>; |
| pinctrl-1 = <&pinctrl_usdhc3_100mhz>; |
| pinctrl-2 = <&pinctrl_usdhc3_200mhz>; |
| bus-width = <8>; |
| non-removable; |
| status = "okay"; |
| }; |
| |
| &wdog1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_wdog>; |
| fsl,ext-reset-output; |
| status = "okay"; |
| }; |
| |
| &iomuxc { |
| pinctrl_eqos: eqosgrp { |
| fsl,pins = < |
| MX8MP_IOMUXC_ENET_MDC__ENET_QOS_MDC 0x2 |
| MX8MP_IOMUXC_ENET_MDIO__ENET_QOS_MDIO 0x2 |
| MX8MP_IOMUXC_ENET_RD0__ENET_QOS_RGMII_RD0 0x90 |
| MX8MP_IOMUXC_ENET_RD1__ENET_QOS_RGMII_RD1 0x90 |
| MX8MP_IOMUXC_ENET_RD2__ENET_QOS_RGMII_RD2 0x90 |
| MX8MP_IOMUXC_ENET_RD3__ENET_QOS_RGMII_RD3 0x90 |
| MX8MP_IOMUXC_ENET_RXC__CCM_ENET_QOS_CLOCK_GENERATE_RX_CLK 0x90 |
| MX8MP_IOMUXC_ENET_RX_CTL__ENET_QOS_RGMII_RX_CTL 0x90 |
| MX8MP_IOMUXC_ENET_TD0__ENET_QOS_RGMII_TD0 0x16 |
| MX8MP_IOMUXC_ENET_TD1__ENET_QOS_RGMII_TD1 0x16 |
| MX8MP_IOMUXC_ENET_TD2__ENET_QOS_RGMII_TD2 0x16 |
| MX8MP_IOMUXC_ENET_TD3__ENET_QOS_RGMII_TD3 0x16 |
| MX8MP_IOMUXC_ENET_TX_CTL__ENET_QOS_RGMII_TX_CTL 0x16 |
| MX8MP_IOMUXC_ENET_TXC__CCM_ENET_QOS_CLOCK_GENERATE_TX_CLK 0x16 |
| >; |
| }; |
| |
| pinctrl_ethphy0: ethphy0grp { |
| fsl,pins = < |
| MX8MP_IOMUXC_NAND_DQS__GPIO3_IO14 0x140 /* RST# */ |
| MX8MP_IOMUXC_NAND_READY_B__GPIO3_IO16 0x150 /* IRQ# */ |
| >; |
| }; |
| |
| pinctrl_gsc: gscgrp { |
| fsl,pins = < |
| MX8MP_IOMUXC_SD1_DATA4__GPIO2_IO06 0x150 /* IRQ# */ |
| >; |
| }; |
| |
| pinctrl_i2c1: i2c1grp { |
| fsl,pins = < |
| MX8MP_IOMUXC_I2C1_SCL__I2C1_SCL 0x400001c2 |
| MX8MP_IOMUXC_I2C1_SDA__I2C1_SDA 0x400001c2 |
| >; |
| }; |
| |
| pinctrl_i2c1_gpio: i2c1gpiogrp { |
| fsl,pins = < |
| MX8MP_IOMUXC_I2C1_SCL__GPIO5_IO14 0x400001c2 |
| MX8MP_IOMUXC_I2C1_SDA__GPIO5_IO15 0x400001c2 |
| >; |
| }; |
| |
| pinctrl_i2c2: i2c2grp { |
| fsl,pins = < |
| MX8MP_IOMUXC_I2C2_SCL__I2C2_SCL 0x400001c2 |
| MX8MP_IOMUXC_I2C2_SDA__I2C2_SDA 0x400001c2 |
| >; |
| }; |
| |
| pinctrl_i2c2_gpio: i2c2gpiogrp { |
| fsl,pins = < |
| MX8MP_IOMUXC_I2C2_SCL__GPIO5_IO16 0x400001c2 |
| MX8MP_IOMUXC_I2C2_SDA__GPIO5_IO17 0x400001c2 |
| >; |
| }; |
| |
| pinctrl_i2c3: i2c3grp { |
| fsl,pins = < |
| MX8MP_IOMUXC_I2C3_SCL__I2C3_SCL 0x400001c2 |
| MX8MP_IOMUXC_I2C3_SDA__I2C3_SDA 0x400001c2 |
| >; |
| }; |
| |
| pinctrl_i2c3_gpio: i2c3gpiogrp { |
| fsl,pins = < |
| MX8MP_IOMUXC_I2C3_SCL__GPIO5_IO18 0x400001c2 |
| MX8MP_IOMUXC_I2C3_SDA__GPIO5_IO19 0x400001c2 |
| >; |
| }; |
| |
| pinctrl_uart1: uart1grp { |
| fsl,pins = < |
| MX8MP_IOMUXC_UART1_RXD__UART1_DCE_RX 0x140 |
| MX8MP_IOMUXC_UART1_TXD__UART1_DCE_TX 0x140 |
| >; |
| }; |
| |
| pinctrl_uart2: uart2grp { |
| fsl,pins = < |
| MX8MP_IOMUXC_UART2_RXD__UART2_DCE_RX 0x140 |
| MX8MP_IOMUXC_UART2_TXD__UART2_DCE_TX 0x140 |
| >; |
| }; |
| |
| pinctrl_uart3: uart3grp { |
| fsl,pins = < |
| MX8MP_IOMUXC_UART3_RXD__UART3_DCE_RX 0x140 |
| MX8MP_IOMUXC_UART3_TXD__UART3_DCE_TX 0x140 |
| >; |
| }; |
| |
| pinctrl_usdhc1: usdhc1grp { |
| fsl,pins = < |
| MX8MP_IOMUXC_SD1_CLK__USDHC1_CLK 0x190 |
| MX8MP_IOMUXC_SD1_CMD__USDHC1_CMD 0x1d0 |
| MX8MP_IOMUXC_SD1_DATA0__USDHC1_DATA0 0x1d0 |
| MX8MP_IOMUXC_SD1_DATA1__USDHC1_DATA1 0x1d0 |
| MX8MP_IOMUXC_SD1_DATA2__USDHC1_DATA2 0x1d0 |
| MX8MP_IOMUXC_SD1_DATA3__USDHC1_DATA3 0x1d0 |
| >; |
| }; |
| |
| pinctrl_usdhc3: usdhc3grp { |
| fsl,pins = < |
| MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x190 |
| MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d0 |
| MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d0 |
| MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d0 |
| MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d0 |
| MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d0 |
| MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d0 |
| MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d0 |
| MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d0 |
| MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d0 |
| MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x190 |
| >; |
| }; |
| |
| pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp { |
| fsl,pins = < |
| MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x194 |
| MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d4 |
| MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d4 |
| MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d4 |
| MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d4 |
| MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d4 |
| MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d4 |
| MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d4 |
| MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d4 |
| MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d4 |
| MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x194 |
| >; |
| }; |
| |
| pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp { |
| fsl,pins = < |
| MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x196 |
| MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d6 |
| MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d6 |
| MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d6 |
| MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d6 |
| MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d6 |
| MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d6 |
| MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d6 |
| MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d6 |
| MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d6 |
| MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x196 |
| >; |
| }; |
| |
| pinctrl_wdog: wdoggrp { |
| fsl,pins = < |
| MX8MP_IOMUXC_GPIO1_IO02__WDOG1_WDOG_B 0x166 |
| >; |
| }; |
| }; |
