| // SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| /* |
| * Copyright 2017 NXP |
| * Copyright (C) 2017-2018 Pengutronix, Lucas Stach <kernel@pengutronix.de> |
| */ |
| |
| #include <dt-bindings/clock/imx8mq-clock.h> |
| #include <dt-bindings/power/imx8mq-power.h> |
| #include <dt-bindings/reset/imx8mq-reset.h> |
| #include <dt-bindings/gpio/gpio.h> |
| #include "dt-bindings/input/input.h" |
| #include <dt-bindings/interrupt-controller/arm-gic.h> |
| #include <dt-bindings/thermal/thermal.h> |
| #include <dt-bindings/interconnect/imx8mq.h> |
| #include "imx8mq-pinfunc.h" |
| |
| / { |
| interrupt-parent = <&gpc>; |
| |
| #address-cells = <2>; |
| #size-cells = <2>; |
| |
| aliases { |
| ethernet0 = &fec1; |
| gpio0 = &gpio1; |
| gpio1 = &gpio2; |
| gpio2 = &gpio3; |
| gpio3 = &gpio4; |
| gpio4 = &gpio5; |
| i2c0 = &i2c1; |
| i2c1 = &i2c2; |
| i2c2 = &i2c3; |
| i2c3 = &i2c4; |
| mmc0 = &usdhc1; |
| mmc1 = &usdhc2; |
| serial0 = &uart1; |
| serial1 = &uart2; |
| serial2 = &uart3; |
| serial3 = &uart4; |
| spi0 = &ecspi1; |
| spi1 = &ecspi2; |
| spi2 = &ecspi3; |
| }; |
| |
| ckil: clock-ckil { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <32768>; |
| clock-output-names = "ckil"; |
| }; |
| |
| osc_25m: clock-osc-25m { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <25000000>; |
| clock-output-names = "osc_25m"; |
| }; |
| |
| osc_27m: clock-osc-27m { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <27000000>; |
| clock-output-names = "osc_27m"; |
| }; |
| |
| hdmi_phy_27m: clock-hdmi-phy-27m { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <27000000>; |
| clock-output-names = "hdmi_phy_27m"; |
| }; |
| |
| clk_ext1: clock-ext1 { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <133000000>; |
| clock-output-names = "clk_ext1"; |
| }; |
| |
| clk_ext2: clock-ext2 { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <133000000>; |
| clock-output-names = "clk_ext2"; |
| }; |
| |
| clk_ext3: clock-ext3 { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <133000000>; |
| clock-output-names = "clk_ext3"; |
| }; |
| |
| clk_ext4: clock-ext4 { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <133000000>; |
| clock-output-names = "clk_ext4"; |
| }; |
| |
| cpus { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| A53_0: cpu@0 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a53"; |
| reg = <0x0>; |
| clock-latency = <61036>; /* two CLK32 periods */ |
| clocks = <&clk IMX8MQ_CLK_ARM>; |
| enable-method = "psci"; |
| i-cache-size = <0x8000>; |
| i-cache-line-size = <64>; |
| i-cache-sets = <256>; |
| d-cache-size = <0x8000>; |
| d-cache-line-size = <64>; |
| d-cache-sets = <128>; |
| next-level-cache = <&A53_L2>; |
| operating-points-v2 = <&a53_opp_table>; |
| #cooling-cells = <2>; |
| nvmem-cells = <&cpu_speed_grade>; |
| nvmem-cell-names = "speed_grade"; |
| }; |
| |
| A53_1: cpu@1 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a53"; |
| reg = <0x1>; |
| clock-latency = <61036>; /* two CLK32 periods */ |
| clocks = <&clk IMX8MQ_CLK_ARM>; |
| enable-method = "psci"; |
| i-cache-size = <0x8000>; |
| i-cache-line-size = <64>; |
| i-cache-sets = <256>; |
| d-cache-size = <0x8000>; |
| d-cache-line-size = <64>; |
| d-cache-sets = <128>; |
| next-level-cache = <&A53_L2>; |
| operating-points-v2 = <&a53_opp_table>; |
| #cooling-cells = <2>; |
| }; |
| |
| A53_2: cpu@2 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a53"; |
| reg = <0x2>; |
| clock-latency = <61036>; /* two CLK32 periods */ |
| clocks = <&clk IMX8MQ_CLK_ARM>; |
| enable-method = "psci"; |
| i-cache-size = <0x8000>; |
| i-cache-line-size = <64>; |
| i-cache-sets = <256>; |
| d-cache-size = <0x8000>; |
| d-cache-line-size = <64>; |
| d-cache-sets = <128>; |
| next-level-cache = <&A53_L2>; |
| operating-points-v2 = <&a53_opp_table>; |
| #cooling-cells = <2>; |
| }; |
| |
| A53_3: cpu@3 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a53"; |
| reg = <0x3>; |
| clock-latency = <61036>; /* two CLK32 periods */ |
| clocks = <&clk IMX8MQ_CLK_ARM>; |
| enable-method = "psci"; |
| i-cache-size = <0x8000>; |
| i-cache-line-size = <64>; |
| i-cache-sets = <256>; |
| d-cache-size = <0x8000>; |
| d-cache-line-size = <64>; |
| d-cache-sets = <128>; |
| next-level-cache = <&A53_L2>; |
| operating-points-v2 = <&a53_opp_table>; |
| #cooling-cells = <2>; |
| }; |
| |
| A53_L2: l2-cache0 { |
| compatible = "cache"; |
| cache-level = <2>; |
| cache-unified; |
| cache-size = <0x100000>; |
| cache-line-size = <64>; |
| cache-sets = <1024>; |
| }; |
| }; |
| |
| a53_opp_table: opp-table { |
| compatible = "operating-points-v2"; |
| opp-shared; |
| |
| opp-800000000 { |
| opp-hz = /bits/ 64 <800000000>; |
| opp-microvolt = <900000>; |
| /* Industrial only */ |
| opp-supported-hw = <0xf>, <0x4>; |
| clock-latency-ns = <150000>; |
| opp-suspend; |
| }; |
| |
| opp-1000000000 { |
| opp-hz = /bits/ 64 <1000000000>; |
| opp-microvolt = <900000>; |
| /* Consumer only */ |
| opp-supported-hw = <0xe>, <0x3>; |
| clock-latency-ns = <150000>; |
| opp-suspend; |
| }; |
| |
| opp-1300000000 { |
| opp-hz = /bits/ 64 <1300000000>; |
| opp-microvolt = <1000000>; |
| opp-supported-hw = <0xc>, <0x4>; |
| clock-latency-ns = <150000>; |
| opp-suspend; |
| }; |
| |
| opp-1500000000 { |
| opp-hz = /bits/ 64 <1500000000>; |
| opp-microvolt = <1000000>; |
| opp-supported-hw = <0x8>, <0x3>; |
| clock-latency-ns = <150000>; |
| opp-suspend; |
| }; |
| }; |
| |
| funnel { |
| /* |
| * non-configurable funnel don't show up on the AMBA |
| * bus. As such no need to add "arm,primecell". |
| */ |
| compatible = "arm,coresight-static-funnel"; |
| |
| in-ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| |
| ca_funnel_in_port0: endpoint { |
| remote-endpoint = <&etm0_out_port>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| |
| ca_funnel_in_port1: endpoint { |
| remote-endpoint = <&etm1_out_port>; |
| }; |
| }; |
| |
| port@2 { |
| reg = <2>; |
| |
| ca_funnel_in_port2: endpoint { |
| remote-endpoint = <&etm2_out_port>; |
| }; |
| }; |
| |
| port@3 { |
| reg = <3>; |
| |
| ca_funnel_in_port3: endpoint { |
| remote-endpoint = <&etm3_out_port>; |
| }; |
| }; |
| }; |
| |
| out-ports { |
| port { |
| ca_funnel_out_port0: endpoint { |
| remote-endpoint = <&hugo_funnel_in_port0>; |
| }; |
| }; |
| }; |
| }; |
| |
| pmu { |
| compatible = "arm,cortex-a53-pmu"; |
| interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-parent = <&gic>; |
| }; |
| |
| psci { |
| compatible = "arm,psci-1.0"; |
| method = "smc"; |
| }; |
| |
| thermal-zones { |
| cpu_thermal: cpu-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <2000>; |
| thermal-sensors = <&tmu 0>; |
| |
| trips { |
| cpu_alert: cpu-alert { |
| temperature = <80000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu-crit { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| }; |
| |
| cooling-maps { |
| map0 { |
| trip = <&cpu_alert>; |
| cooling-device = |
| <&A53_0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&A53_1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&A53_2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&A53_3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| }; |
| }; |
| |
| gpu-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <2000>; |
| thermal-sensors = <&tmu 1>; |
| |
| trips { |
| gpu_alert: gpu-alert { |
| temperature = <80000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| gpu-crit { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| }; |
| |
| cooling-maps { |
| map0 { |
| trip = <&gpu_alert>; |
| cooling-device = |
| <&gpu THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| }; |
| }; |
| |
| vpu-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <2000>; |
| thermal-sensors = <&tmu 2>; |
| |
| trips { |
| vpu-crit { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| }; |
| |
| timer { |
| compatible = "arm,armv8-timer"; |
| interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>, /* Physical Secure */ |
| <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>, /* Physical Non-Secure */ |
| <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>, /* Virtual */ |
| <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>; /* Hypervisor */ |
| interrupt-parent = <&gic>; |
| arm,no-tick-in-suspend; |
| }; |
| |
| soc: soc@0 { |
| compatible = "fsl,imx8mq-soc", "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0x0 0x0 0x0 0x3e000000>; |
| dma-ranges = <0x40000000 0x0 0x40000000 0xc0000000>; |
| nvmem-cells = <&imx8mq_uid>; |
| nvmem-cell-names = "soc_unique_id"; |
| |
| etm0: etm@28440000 { |
| compatible = "arm,coresight-etm4x", "arm,primecell"; |
| reg = <0x28440000 0x1000>; |
| cpu = <&A53_0>; |
| clocks = <&clk IMX8MQ_CLK_MAIN_AXI>; |
| clock-names = "apb_pclk"; |
| |
| out-ports { |
| port { |
| etm0_out_port: endpoint { |
| remote-endpoint = <&ca_funnel_in_port0>; |
| }; |
| }; |
| }; |
| }; |
| |
| etm1: etm@28540000 { |
| compatible = "arm,coresight-etm4x", "arm,primecell"; |
| reg = <0x28540000 0x1000>; |
| cpu = <&A53_1>; |
| clocks = <&clk IMX8MQ_CLK_MAIN_AXI>; |
| clock-names = "apb_pclk"; |
| |
| out-ports { |
| port { |
| etm1_out_port: endpoint { |
| remote-endpoint = <&ca_funnel_in_port1>; |
| }; |
| }; |
| }; |
| }; |
| |
| etm2: etm@28640000 { |
| compatible = "arm,coresight-etm4x", "arm,primecell"; |
| reg = <0x28640000 0x1000>; |
| cpu = <&A53_2>; |
| clocks = <&clk IMX8MQ_CLK_MAIN_AXI>; |
| clock-names = "apb_pclk"; |
| |
| out-ports { |
| port { |
| etm2_out_port: endpoint { |
| remote-endpoint = <&ca_funnel_in_port2>; |
| }; |
| }; |
| }; |
| }; |
| |
| etm3: etm@28740000 { |
| compatible = "arm,coresight-etm4x", "arm,primecell"; |
| reg = <0x28740000 0x1000>; |
| cpu = <&A53_3>; |
| clocks = <&clk IMX8MQ_CLK_MAIN_AXI>; |
| clock-names = "apb_pclk"; |
| |
| out-ports { |
| port { |
| etm3_out_port: endpoint { |
| remote-endpoint = <&ca_funnel_in_port3>; |
| }; |
| }; |
| }; |
| }; |
| |
| funnel@28c03000 { |
| compatible = "arm,coresight-dynamic-funnel", "arm,primecell"; |
| reg = <0x28c03000 0x1000>; |
| clocks = <&clk IMX8MQ_CLK_MAIN_AXI>; |
| clock-names = "apb_pclk"; |
| |
| in-ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| |
| hugo_funnel_in_port0: endpoint { |
| remote-endpoint = <&ca_funnel_out_port0>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| |
| hugo_funnel_in_port1: endpoint { |
| /* M4 input */ |
| }; |
| }; |
| /* the other input ports are not connect to anything */ |
| }; |
| |
| out-ports { |
| port { |
| hugo_funnel_out_port0: endpoint { |
| remote-endpoint = <&etf_in_port>; |
| }; |
| }; |
| }; |
| }; |
| |
| etf@28c04000 { |
| compatible = "arm,coresight-tmc", "arm,primecell"; |
| reg = <0x28c04000 0x1000>; |
| clocks = <&clk IMX8MQ_CLK_MAIN_AXI>; |
| clock-names = "apb_pclk"; |
| |
| in-ports { |
| port { |
| etf_in_port: endpoint { |
| remote-endpoint = <&hugo_funnel_out_port0>; |
| }; |
| }; |
| }; |
| |
| out-ports { |
| port { |
| etf_out_port: endpoint { |
| remote-endpoint = <&etr_in_port>; |
| }; |
| }; |
| }; |
| }; |
| |
| etr@28c06000 { |
| compatible = "arm,coresight-tmc", "arm,primecell"; |
| reg = <0x28c06000 0x1000>; |
| clocks = <&clk IMX8MQ_CLK_MAIN_AXI>; |
| clock-names = "apb_pclk"; |
| |
| in-ports { |
| port { |
| etr_in_port: endpoint { |
| remote-endpoint = <&etf_out_port>; |
| }; |
| }; |
| }; |
| }; |
| |
| aips1: bus@30000000 { /* AIPS1 */ |
| compatible = "fsl,aips-bus", "simple-bus"; |
| reg = <0x30000000 0x400000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0x30000000 0x30000000 0x400000>; |
| |
| sai1: sai@30010000 { |
| #sound-dai-cells = <0>; |
| compatible = "fsl,imx8mq-sai"; |
| reg = <0x30010000 0x10000>; |
| interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MQ_CLK_SAI1_IPG>, |
| <&clk IMX8MQ_CLK_SAI1_ROOT>, |
| <&clk IMX8MQ_CLK_DUMMY>, <&clk IMX8MQ_CLK_DUMMY>; |
| clock-names = "bus", "mclk1", "mclk2", "mclk3"; |
| dmas = <&sdma2 8 24 0>, <&sdma1 9 24 0>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| sai6: sai@30030000 { |
| #sound-dai-cells = <0>; |
| compatible = "fsl,imx8mq-sai"; |
| reg = <0x30030000 0x10000>; |
| interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MQ_CLK_SAI6_IPG>, |
| <&clk IMX8MQ_CLK_SAI6_ROOT>, |
| <&clk IMX8MQ_CLK_DUMMY>, <&clk IMX8MQ_CLK_DUMMY>; |
| clock-names = "bus", "mclk1", "mclk2", "mclk3"; |
| dmas = <&sdma2 4 24 0>, <&sdma2 5 24 0>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| sai5: sai@30040000 { |
| #sound-dai-cells = <0>; |
| compatible = "fsl,imx8mq-sai"; |
| reg = <0x30040000 0x10000>; |
| interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MQ_CLK_SAI5_IPG>, |
| <&clk IMX8MQ_CLK_SAI5_ROOT>, |
| <&clk IMX8MQ_CLK_DUMMY>, <&clk IMX8MQ_CLK_DUMMY>; |
| clock-names = "bus", "mclk1", "mclk2", "mclk3"; |
| dmas = <&sdma2 2 24 0>, <&sdma2 3 24 0>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| sai4: sai@30050000 { |
| #sound-dai-cells = <0>; |
| compatible = "fsl,imx8mq-sai"; |
| reg = <0x30050000 0x10000>; |
| interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MQ_CLK_SAI4_IPG>, |
| <&clk IMX8MQ_CLK_SAI4_ROOT>, |
| <&clk IMX8MQ_CLK_DUMMY>, <&clk IMX8MQ_CLK_DUMMY>; |
| clock-names = "bus", "mclk1", "mclk2", "mclk3"; |
| dmas = <&sdma2 0 24 0>, <&sdma2 1 24 0>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| gpio1: gpio@30200000 { |
| compatible = "fsl,imx8mq-gpio", "fsl,imx35-gpio"; |
| reg = <0x30200000 0x10000>; |
| interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MQ_CLK_GPIO1_ROOT>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| gpio-ranges = <&iomuxc 0 10 30>; |
| }; |
| |
| gpio2: gpio@30210000 { |
| compatible = "fsl,imx8mq-gpio", "fsl,imx35-gpio"; |
| reg = <0x30210000 0x10000>; |
| interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MQ_CLK_GPIO2_ROOT>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| gpio-ranges = <&iomuxc 0 40 21>; |
| }; |
| |
| gpio3: gpio@30220000 { |
| compatible = "fsl,imx8mq-gpio", "fsl,imx35-gpio"; |
| reg = <0x30220000 0x10000>; |
| interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MQ_CLK_GPIO3_ROOT>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| gpio-ranges = <&iomuxc 0 61 26>; |
| }; |
| |
| gpio4: gpio@30230000 { |
| compatible = "fsl,imx8mq-gpio", "fsl,imx35-gpio"; |
| reg = <0x30230000 0x10000>; |
| interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MQ_CLK_GPIO4_ROOT>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| gpio-ranges = <&iomuxc 0 87 32>; |
| }; |
| |
| gpio5: gpio@30240000 { |
| compatible = "fsl,imx8mq-gpio", "fsl,imx35-gpio"; |
| reg = <0x30240000 0x10000>; |
| interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MQ_CLK_GPIO5_ROOT>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| gpio-ranges = <&iomuxc 0 119 30>; |
| }; |
| |
| tmu: tmu@30260000 { |
| compatible = "fsl,imx8mq-tmu"; |
| reg = <0x30260000 0x10000>; |
| interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MQ_CLK_TMU_ROOT>; |
| little-endian; |
| fsl,tmu-range = <0xb0000 0xa0026 0x80048 0x70061>; |
| fsl,tmu-calibration = <0x00000000 0x00000023>, |
| <0x00000001 0x00000029>, |
| <0x00000002 0x0000002f>, |
| <0x00000003 0x00000035>, |
| <0x00000004 0x0000003d>, |
| <0x00000005 0x00000043>, |
| <0x00000006 0x0000004b>, |
| <0x00000007 0x00000051>, |
| <0x00000008 0x00000057>, |
| <0x00000009 0x0000005f>, |
| <0x0000000a 0x00000067>, |
| <0x0000000b 0x0000006f>, |
| |
| <0x00010000 0x0000001b>, |
| <0x00010001 0x00000023>, |
| <0x00010002 0x0000002b>, |
| <0x00010003 0x00000033>, |
| <0x00010004 0x0000003b>, |
| <0x00010005 0x00000043>, |
| <0x00010006 0x0000004b>, |
| <0x00010007 0x00000055>, |
| <0x00010008 0x0000005d>, |
| <0x00010009 0x00000067>, |
| <0x0001000a 0x00000070>, |
| |
| <0x00020000 0x00000017>, |
| <0x00020001 0x00000023>, |
| <0x00020002 0x0000002d>, |
| <0x00020003 0x00000037>, |
| <0x00020004 0x00000041>, |
| <0x00020005 0x0000004b>, |
| <0x00020006 0x00000057>, |
| <0x00020007 0x00000063>, |
| <0x00020008 0x0000006f>, |
| |
| <0x00030000 0x00000015>, |
| <0x00030001 0x00000021>, |
| <0x00030002 0x0000002d>, |
| <0x00030003 0x00000039>, |
| <0x00030004 0x00000045>, |
| <0x00030005 0x00000053>, |
| <0x00030006 0x0000005f>, |
| <0x00030007 0x00000071>; |
| #thermal-sensor-cells = <1>; |
| }; |
| |
| wdog1: watchdog@30280000 { |
| compatible = "fsl,imx8mq-wdt", "fsl,imx21-wdt"; |
| reg = <0x30280000 0x10000>; |
| interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MQ_CLK_WDOG1_ROOT>; |
| status = "disabled"; |
| }; |
| |
| wdog2: watchdog@30290000 { |
| compatible = "fsl,imx8mq-wdt", "fsl,imx21-wdt"; |
| reg = <0x30290000 0x10000>; |
| interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MQ_CLK_WDOG2_ROOT>; |
| status = "disabled"; |
| }; |
| |
| wdog3: watchdog@302a0000 { |
| compatible = "fsl,imx8mq-wdt", "fsl,imx21-wdt"; |
| reg = <0x302a0000 0x10000>; |
| interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MQ_CLK_WDOG3_ROOT>; |
| status = "disabled"; |
| }; |
| |
| sdma2: dma-controller@302c0000 { |
| compatible = "fsl,imx8mq-sdma","fsl,imx7d-sdma"; |
| reg = <0x302c0000 0x10000>; |
| interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MQ_CLK_SDMA2_ROOT>, |
| <&clk IMX8MQ_CLK_SDMA2_ROOT>; |
| clock-names = "ipg", "ahb"; |
| #dma-cells = <3>; |
| fsl,sdma-ram-script-name = "imx/sdma/sdma-imx7d.bin"; |
| }; |
| |
| lcdif: lcd-controller@30320000 { |
| compatible = "fsl,imx8mq-lcdif", "fsl,imx6sx-lcdif"; |
| reg = <0x30320000 0x10000>; |
| interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MQ_CLK_LCDIF_PIXEL>, |
| <&clk IMX8MQ_CLK_DISP_APB_ROOT>, |
| <&clk IMX8MQ_CLK_DISP_AXI_ROOT>; |
| clock-names = "pix", "axi", "disp_axi"; |
| assigned-clocks = <&clk IMX8MQ_VIDEO_PLL1_REF_SEL>, |
| <&clk IMX8MQ_VIDEO_PLL1_BYPASS>, |
| <&clk IMX8MQ_CLK_LCDIF_PIXEL>, |
| <&clk IMX8MQ_VIDEO_PLL1>; |
| assigned-clock-parents = <&clk IMX8MQ_CLK_25M>, |
| <&clk IMX8MQ_VIDEO_PLL1>, |
| <&clk IMX8MQ_VIDEO_PLL1_OUT>; |
| assigned-clock-rates = <0>, <0>, <0>, <594000000>; |
| status = "disabled"; |
| |
| port { |
| lcdif_mipi_dsi: endpoint { |
| remote-endpoint = <&mipi_dsi_lcdif_in>; |
| }; |
| }; |
| }; |
| |
| iomuxc: pinctrl@30330000 { |
| compatible = "fsl,imx8mq-iomuxc"; |
| reg = <0x30330000 0x10000>; |
| }; |
| |
| iomuxc_gpr: syscon@30340000 { |
| compatible = "fsl,imx8mq-iomuxc-gpr", "syscon", "simple-mfd"; |
| reg = <0x30340000 0x10000>; |
| |
| mux: mux-controller { |
| compatible = "mmio-mux"; |
| #mux-control-cells = <1>; |
| mux-reg-masks = <0x34 0x00000004>; /* MIPI_MUX_SEL */ |
| }; |
| }; |
| |
| ocotp: efuse@30350000 { |
| compatible = "fsl,imx8mq-ocotp", "syscon"; |
| reg = <0x30350000 0x10000>; |
| clocks = <&clk IMX8MQ_CLK_OCOTP_ROOT>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| /* |
| * The register address below maps to the MX8M |
| * Fusemap Description Table entries this way. |
| * Assuming |
| * reg = <ADDR SIZE>; |
| * then |
| * Fuse Address = (ADDR * 4) + 0x400 |
| * Note that if SIZE is greater than 4, then |
| * each subsequent fuse is located at offset |
| * +0x10 in Fusemap Description Table (e.g. |
| * reg = <0x4 0x8> describes fuses 0x410 and |
| * 0x420). |
| */ |
| imx8mq_uid: soc-uid@4 { /* 0x410-0x420 */ |
| reg = <0x4 0x8>; |
| }; |
| |
| cpu_speed_grade: speed-grade@10 { /* 0x440 */ |
| reg = <0x10 4>; |
| }; |
| |
| fec_mac_address: mac-address@90 { /* 0x640 */ |
| reg = <0x90 6>; |
| }; |
| }; |
| |
| anatop: clock-controller@30360000 { |
| compatible = "fsl,imx8mq-anatop"; |
| reg = <0x30360000 0x10000>; |
| interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>; |
| #clock-cells = <1>; |
| }; |
| |
| snvs: snvs@30370000 { |
| compatible = "fsl,sec-v4.0-mon", "syscon", "simple-mfd"; |
| reg = <0x30370000 0x10000>; |
| |
| snvs_rtc: snvs-rtc-lp { |
| compatible = "fsl,sec-v4.0-mon-rtc-lp"; |
| regmap = <&snvs>; |
| offset = <0x34>; |
| interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MQ_CLK_SNVS_ROOT>; |
| clock-names = "snvs-rtc"; |
| }; |
| |
| snvs_pwrkey: snvs-powerkey { |
| compatible = "fsl,sec-v4.0-pwrkey"; |
| regmap = <&snvs>; |
| interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MQ_CLK_SNVS_ROOT>; |
| clock-names = "snvs-pwrkey"; |
| linux,keycode = <KEY_POWER>; |
| wakeup-source; |
| status = "disabled"; |
| }; |
| }; |
| |
| clk: clock-controller@30380000 { |
| compatible = "fsl,imx8mq-ccm"; |
| reg = <0x30380000 0x10000>; |
| interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>; |
| #clock-cells = <1>; |
| clocks = <&ckil>, <&osc_25m>, <&osc_27m>, |
| <&clk_ext1>, <&clk_ext2>, |
| <&clk_ext3>, <&clk_ext4>; |
| clock-names = "ckil", "osc_25m", "osc_27m", |
| "clk_ext1", "clk_ext2", |
| "clk_ext3", "clk_ext4"; |
| assigned-clocks = <&clk IMX8MQ_CLK_A53_SRC>, |
| <&clk IMX8MQ_CLK_A53_CORE>, |
| <&clk IMX8MQ_CLK_NOC>, |
| <&clk IMX8MQ_CLK_AUDIO_AHB>, |
| <&clk IMX8MQ_AUDIO_PLL1_BYPASS>, |
| <&clk IMX8MQ_AUDIO_PLL2_BYPASS>, |
| <&clk IMX8MQ_AUDIO_PLL1>, |
| <&clk IMX8MQ_AUDIO_PLL2>; |
| assigned-clock-rates = <0>, <0>, |
| <800000000>, |
| <0>, |
| <0>, |
| <0>, |
| <786432000>, |
| <722534400>; |
| assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_800M>, |
| <&clk IMX8MQ_ARM_PLL_OUT>, |
| <0>, |
| <&clk IMX8MQ_SYS2_PLL_500M>, |
| <&clk IMX8MQ_AUDIO_PLL1>, |
| <&clk IMX8MQ_AUDIO_PLL2>; |
| }; |
| |
| src: reset-controller@30390000 { |
| compatible = "fsl,imx8mq-src", "syscon"; |
| reg = <0x30390000 0x10000>; |
| interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>; |
| #reset-cells = <1>; |
| }; |
| |
| gpc: gpc@303a0000 { |
| compatible = "fsl,imx8mq-gpc"; |
| reg = <0x303a0000 0x10000>; |
| interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-parent = <&gic>; |
| interrupt-controller; |
| #interrupt-cells = <3>; |
| |
| pgc { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pgc_mipi: power-domain@0 { |
| #power-domain-cells = <0>; |
| reg = <IMX8M_POWER_DOMAIN_MIPI>; |
| }; |
| |
| /* |
| * As per comment in ATF source code: |
| * |
| * PCIE1 and PCIE2 share the |
| * same reset signal, if we |
| * power down PCIE2, PCIE1 |
| * will be held in reset too. |
| * |
| * So instead of creating two |
| * separate power domains for |
| * PCIE1 and PCIE2 we create a |
| * link between both and use |
| * it as a shared PCIE power |
| * domain. |
| */ |
| pgc_pcie: power-domain@1 { |
| #power-domain-cells = <0>; |
| reg = <IMX8M_POWER_DOMAIN_PCIE1>; |
| power-domains = <&pgc_pcie2>; |
| }; |
| |
| pgc_otg1: power-domain@2 { |
| #power-domain-cells = <0>; |
| reg = <IMX8M_POWER_DOMAIN_USB_OTG1>; |
| }; |
| |
| pgc_otg2: power-domain@3 { |
| #power-domain-cells = <0>; |
| reg = <IMX8M_POWER_DOMAIN_USB_OTG2>; |
| }; |
| |
| pgc_ddr1: power-domain@4 { |
| #power-domain-cells = <0>; |
| reg = <IMX8M_POWER_DOMAIN_DDR1>; |
| }; |
| |
| pgc_gpu: power-domain@5 { |
| #power-domain-cells = <0>; |
| reg = <IMX8M_POWER_DOMAIN_GPU>; |
| clocks = <&clk IMX8MQ_CLK_GPU_ROOT>, |
| <&clk IMX8MQ_CLK_GPU_SHADER_DIV>, |
| <&clk IMX8MQ_CLK_GPU_AXI>, |
| <&clk IMX8MQ_CLK_GPU_AHB>; |
| }; |
| |
| pgc_vpu: power-domain@6 { |
| #power-domain-cells = <0>; |
| reg = <IMX8M_POWER_DOMAIN_VPU>; |
| clocks = <&clk IMX8MQ_CLK_VPU_DEC_ROOT>, |
| <&clk IMX8MQ_CLK_VPU_G1_ROOT>, |
| <&clk IMX8MQ_CLK_VPU_G2_ROOT>; |
| assigned-clocks = <&clk IMX8MQ_CLK_VPU_G1>, |
| <&clk IMX8MQ_CLK_VPU_G2>, |
| <&clk IMX8MQ_CLK_VPU_BUS>, |
| <&clk IMX8MQ_VPU_PLL_BYPASS>; |
| assigned-clock-parents = <&clk IMX8MQ_VPU_PLL_OUT>, |
| <&clk IMX8MQ_VPU_PLL_OUT>, |
| <&clk IMX8MQ_SYS1_PLL_800M>, |
| <&clk IMX8MQ_VPU_PLL>; |
| assigned-clock-rates = <600000000>, |
| <300000000>, |
| <800000000>, |
| <0>; |
| }; |
| |
| pgc_disp: power-domain@7 { |
| #power-domain-cells = <0>; |
| reg = <IMX8M_POWER_DOMAIN_DISP>; |
| }; |
| |
| pgc_mipi_csi1: power-domain@8 { |
| #power-domain-cells = <0>; |
| reg = <IMX8M_POWER_DOMAIN_MIPI_CSI1>; |
| }; |
| |
| pgc_mipi_csi2: power-domain@9 { |
| #power-domain-cells = <0>; |
| reg = <IMX8M_POWER_DOMAIN_MIPI_CSI2>; |
| }; |
| |
| pgc_pcie2: power-domain@a { |
| #power-domain-cells = <0>; |
| reg = <IMX8M_POWER_DOMAIN_PCIE2>; |
| }; |
| }; |
| }; |
| }; |
| |
| aips2: bus@30400000 { /* AIPS2 */ |
| compatible = "fsl,aips-bus", "simple-bus"; |
| reg = <0x30400000 0x400000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0x30400000 0x30400000 0x400000>; |
| |
| pwm1: pwm@30660000 { |
| compatible = "fsl,imx8mq-pwm", "fsl,imx27-pwm"; |
| reg = <0x30660000 0x10000>; |
| interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MQ_CLK_PWM1_ROOT>, |
| <&clk IMX8MQ_CLK_PWM1_ROOT>; |
| clock-names = "ipg", "per"; |
| #pwm-cells = <3>; |
| status = "disabled"; |
| }; |
| |
| pwm2: pwm@30670000 { |
| compatible = "fsl,imx8mq-pwm", "fsl,imx27-pwm"; |
| reg = <0x30670000 0x10000>; |
| interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MQ_CLK_PWM2_ROOT>, |
| <&clk IMX8MQ_CLK_PWM2_ROOT>; |
| clock-names = "ipg", "per"; |
| #pwm-cells = <3>; |
| status = "disabled"; |
| }; |
| |
| pwm3: pwm@30680000 { |
| compatible = "fsl,imx8mq-pwm", "fsl,imx27-pwm"; |
| reg = <0x30680000 0x10000>; |
| interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MQ_CLK_PWM3_ROOT>, |
| <&clk IMX8MQ_CLK_PWM3_ROOT>; |
| clock-names = "ipg", "per"; |
| #pwm-cells = <3>; |
| status = "disabled"; |
| }; |
| |
| pwm4: pwm@30690000 { |
| compatible = "fsl,imx8mq-pwm", "fsl,imx27-pwm"; |
| reg = <0x30690000 0x10000>; |
| interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MQ_CLK_PWM4_ROOT>, |
| <&clk IMX8MQ_CLK_PWM4_ROOT>; |
| clock-names = "ipg", "per"; |
| #pwm-cells = <3>; |
| status = "disabled"; |
| }; |
| |
| system_counter: timer@306a0000 { |
| compatible = "nxp,sysctr-timer"; |
| reg = <0x306a0000 0x20000>; |
| interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&osc_25m>; |
| clock-names = "per"; |
| }; |
| }; |
| |
| aips3: bus@30800000 { /* AIPS3 */ |
| compatible = "fsl,aips-bus", "simple-bus"; |
| reg = <0x30800000 0x400000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0x30800000 0x30800000 0x400000>, |
| <0x08000000 0x08000000 0x10000000>; |
| |
| spdif1: spdif@30810000 { |
| compatible = "fsl,imx35-spdif"; |
| reg = <0x30810000 0x10000>; |
| interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MQ_CLK_IPG_ROOT>, /* core */ |
| <&clk IMX8MQ_CLK_25M>, /* rxtx0 */ |
| <&clk IMX8MQ_CLK_SPDIF1>, /* rxtx1 */ |
| <&clk IMX8MQ_CLK_DUMMY>, /* rxtx2 */ |
| <&clk IMX8MQ_CLK_DUMMY>, /* rxtx3 */ |
| <&clk IMX8MQ_CLK_DUMMY>, /* rxtx4 */ |
| <&clk IMX8MQ_CLK_IPG_ROOT>, /* rxtx5 */ |
| <&clk IMX8MQ_CLK_DUMMY>, /* rxtx6 */ |
| <&clk IMX8MQ_CLK_DUMMY>, /* rxtx7 */ |
| <&clk IMX8MQ_CLK_DUMMY>; /* spba */ |
| clock-names = "core", "rxtx0", |
| "rxtx1", "rxtx2", |
| "rxtx3", "rxtx4", |
| "rxtx5", "rxtx6", |
| "rxtx7", "spba"; |
| dmas = <&sdma1 8 18 0>, <&sdma1 9 18 0>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| ecspi1: spi@30820000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,imx8mq-ecspi", "fsl,imx51-ecspi"; |
| reg = <0x30820000 0x10000>; |
| interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MQ_CLK_ECSPI1_ROOT>, |
| <&clk IMX8MQ_CLK_ECSPI1_ROOT>; |
| clock-names = "ipg", "per"; |
| dmas = <&sdma1 0 7 1>, <&sdma1 1 7 2>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| ecspi2: spi@30830000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,imx8mq-ecspi", "fsl,imx51-ecspi"; |
| reg = <0x30830000 0x10000>; |
| interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MQ_CLK_ECSPI2_ROOT>, |
| <&clk IMX8MQ_CLK_ECSPI2_ROOT>; |
| clock-names = "ipg", "per"; |
| dmas = <&sdma1 2 7 1>, <&sdma1 3 7 2>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| ecspi3: spi@30840000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,imx8mq-ecspi", "fsl,imx51-ecspi"; |
| reg = <0x30840000 0x10000>; |
| interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MQ_CLK_ECSPI3_ROOT>, |
| <&clk IMX8MQ_CLK_ECSPI3_ROOT>; |
| clock-names = "ipg", "per"; |
| dmas = <&sdma1 4 7 1>, <&sdma1 5 7 2>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| uart1: serial@30860000 { |
| compatible = "fsl,imx8mq-uart", |
| "fsl,imx6q-uart"; |
| reg = <0x30860000 0x10000>; |
| interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MQ_CLK_UART1_ROOT>, |
| <&clk IMX8MQ_CLK_UART1_ROOT>; |
| clock-names = "ipg", "per"; |
| dmas = <&sdma1 22 4 0>, <&sdma1 23 4 0>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| uart3: serial@30880000 { |
| compatible = "fsl,imx8mq-uart", |
| "fsl,imx6q-uart"; |
| reg = <0x30880000 0x10000>; |
| interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MQ_CLK_UART3_ROOT>, |
| <&clk IMX8MQ_CLK_UART3_ROOT>; |
| clock-names = "ipg", "per"; |
| dmas = <&sdma1 26 4 0>, <&sdma1 27 4 0>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| uart2: serial@30890000 { |
| compatible = "fsl,imx8mq-uart", |
| "fsl,imx6q-uart"; |
| reg = <0x30890000 0x10000>; |
| interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MQ_CLK_UART2_ROOT>, |
| <&clk IMX8MQ_CLK_UART2_ROOT>; |
| clock-names = "ipg", "per"; |
| dmas = <&sdma1 24 4 0>, <&sdma1 25 4 0>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| spdif2: spdif@308a0000 { |
| compatible = "fsl,imx35-spdif"; |
| reg = <0x308a0000 0x10000>; |
| interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MQ_CLK_IPG_ROOT>, /* core */ |
| <&clk IMX8MQ_CLK_25M>, /* rxtx0 */ |
| <&clk IMX8MQ_CLK_SPDIF2>, /* rxtx1 */ |
| <&clk IMX8MQ_CLK_DUMMY>, /* rxtx2 */ |
| <&clk IMX8MQ_CLK_DUMMY>, /* rxtx3 */ |
| <&clk IMX8MQ_CLK_DUMMY>, /* rxtx4 */ |
| <&clk IMX8MQ_CLK_IPG_ROOT>, /* rxtx5 */ |
| <&clk IMX8MQ_CLK_DUMMY>, /* rxtx6 */ |
| <&clk IMX8MQ_CLK_DUMMY>, /* rxtx7 */ |
| <&clk IMX8MQ_CLK_DUMMY>; /* spba */ |
| clock-names = "core", "rxtx0", |
| "rxtx1", "rxtx2", |
| "rxtx3", "rxtx4", |
| "rxtx5", "rxtx6", |
| "rxtx7", "spba"; |
| dmas = <&sdma1 16 18 0>, <&sdma1 17 18 0>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| sai2: sai@308b0000 { |
| #sound-dai-cells = <0>; |
| compatible = "fsl,imx8mq-sai"; |
| reg = <0x308b0000 0x10000>; |
| interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MQ_CLK_SAI2_IPG>, |
| <&clk IMX8MQ_CLK_SAI2_ROOT>, |
| <&clk IMX8MQ_CLK_DUMMY>, <&clk IMX8MQ_CLK_DUMMY>; |
| clock-names = "bus", "mclk1", "mclk2", "mclk3"; |
| dmas = <&sdma1 10 24 0>, <&sdma1 11 24 0>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| sai3: sai@308c0000 { |
| #sound-dai-cells = <0>; |
| compatible = "fsl,imx8mq-sai"; |
| reg = <0x308c0000 0x10000>; |
| interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MQ_CLK_SAI3_IPG>, |
| <&clk IMX8MQ_CLK_SAI3_ROOT>, |
| <&clk IMX8MQ_CLK_DUMMY>, <&clk IMX8MQ_CLK_DUMMY>; |
| clock-names = "bus", "mclk1", "mclk2", "mclk3"; |
| dmas = <&sdma1 12 24 0>, <&sdma1 13 24 0>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| crypto: crypto@30900000 { |
| compatible = "fsl,sec-v4.0"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| reg = <0x30900000 0x40000>; |
| ranges = <0 0x30900000 0x40000>; |
| interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MQ_CLK_AHB>, |
| <&clk IMX8MQ_CLK_IPG_ROOT>; |
| clock-names = "aclk", "ipg"; |
| |
| sec_jr0: jr@1000 { |
| compatible = "fsl,sec-v4.0-job-ring"; |
| reg = <0x1000 0x1000>; |
| interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>; |
| status = "disabled"; |
| }; |
| |
| sec_jr1: jr@2000 { |
| compatible = "fsl,sec-v4.0-job-ring"; |
| reg = <0x2000 0x1000>; |
| interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| sec_jr2: jr@3000 { |
| compatible = "fsl,sec-v4.0-job-ring"; |
| reg = <0x3000 0x1000>; |
| interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| }; |
| |
| mipi_dsi: dsi@30a00000 { |
| compatible = "fsl,imx8mq-nwl-dsi"; |
| reg = <0x30a00000 0x300>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| clocks = <&clk IMX8MQ_CLK_DSI_CORE>, |
| <&clk IMX8MQ_CLK_DSI_AHB>, |
| <&clk IMX8MQ_CLK_DSI_IPG_DIV>, |
| <&clk IMX8MQ_CLK_DSI_PHY_REF>, |
| <&clk IMX8MQ_CLK_LCDIF_PIXEL>; |
| clock-names = "core", "rx_esc", "tx_esc", "phy_ref", "lcdif"; |
| assigned-clocks = <&clk IMX8MQ_CLK_DSI_AHB>, |
| <&clk IMX8MQ_CLK_DSI_CORE>, |
| <&clk IMX8MQ_CLK_DSI_IPG_DIV>; |
| assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_80M>, |
| <&clk IMX8MQ_SYS1_PLL_266M>; |
| assigned-clock-rates = <80000000>, <266000000>, <20000000>; |
| interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; |
| mux-controls = <&mux 0>; |
| power-domains = <&pgc_mipi>; |
| phys = <&dphy>; |
| phy-names = "dphy"; |
| resets = <&src IMX8MQ_RESET_MIPI_DSI_RESET_BYTE_N>, |
| <&src IMX8MQ_RESET_MIPI_DSI_DPI_RESET_N>, |
| <&src IMX8MQ_RESET_MIPI_DSI_ESC_RESET_N>, |
| <&src IMX8MQ_RESET_MIPI_DSI_PCLK_RESET_N>; |
| reset-names = "byte", "dpi", "esc", "pclk"; |
| status = "disabled"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| mipi_dsi_lcdif_in: endpoint@0 { |
| reg = <0>; |
| remote-endpoint = <&lcdif_mipi_dsi>; |
| }; |
| }; |
| }; |
| }; |
| |
| dphy: dphy@30a00300 { |
| compatible = "fsl,imx8mq-mipi-dphy"; |
| reg = <0x30a00300 0x100>; |
| clocks = <&clk IMX8MQ_CLK_DSI_PHY_REF>; |
| clock-names = "phy_ref"; |
| assigned-clocks = <&clk IMX8MQ_VIDEO_PLL1_REF_SEL>, |
| <&clk IMX8MQ_VIDEO_PLL1_BYPASS>, |
| <&clk IMX8MQ_CLK_DSI_PHY_REF>, |
| <&clk IMX8MQ_VIDEO_PLL1>; |
| assigned-clock-parents = <&clk IMX8MQ_CLK_25M>, |
| <&clk IMX8MQ_VIDEO_PLL1>, |
| <&clk IMX8MQ_VIDEO_PLL1_OUT>; |
| assigned-clock-rates = <0>, <0>, <24000000>, <594000000>; |
| #phy-cells = <0>; |
| power-domains = <&pgc_mipi>; |
| status = "disabled"; |
| }; |
| |
| i2c1: i2c@30a20000 { |
| compatible = "fsl,imx8mq-i2c", "fsl,imx21-i2c"; |
| reg = <0x30a20000 0x10000>; |
| interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MQ_CLK_I2C1_ROOT>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| i2c2: i2c@30a30000 { |
| compatible = "fsl,imx8mq-i2c", "fsl,imx21-i2c"; |
| reg = <0x30a30000 0x10000>; |
| interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MQ_CLK_I2C2_ROOT>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| i2c3: i2c@30a40000 { |
| compatible = "fsl,imx8mq-i2c", "fsl,imx21-i2c"; |
| reg = <0x30a40000 0x10000>; |
| interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MQ_CLK_I2C3_ROOT>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| i2c4: i2c@30a50000 { |
| compatible = "fsl,imx8mq-i2c", "fsl,imx21-i2c"; |
| reg = <0x30a50000 0x10000>; |
| interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MQ_CLK_I2C4_ROOT>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| uart4: serial@30a60000 { |
| compatible = "fsl,imx8mq-uart", |
| "fsl,imx6q-uart"; |
| reg = <0x30a60000 0x10000>; |
| interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MQ_CLK_UART4_ROOT>, |
| <&clk IMX8MQ_CLK_UART4_ROOT>; |
| clock-names = "ipg", "per"; |
| dmas = <&sdma1 28 4 0>, <&sdma1 29 4 0>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| mipi_csi1: csi@30a70000 { |
| compatible = "fsl,imx8mq-mipi-csi2"; |
| reg = <0x30a70000 0x1000>; |
| clocks = <&clk IMX8MQ_CLK_CSI1_CORE>, |
| <&clk IMX8MQ_CLK_CSI1_ESC>, |
| <&clk IMX8MQ_CLK_CSI1_PHY_REF>; |
| clock-names = "core", "esc", "ui"; |
| assigned-clocks = <&clk IMX8MQ_CLK_CSI1_CORE>, |
| <&clk IMX8MQ_CLK_CSI1_PHY_REF>, |
| <&clk IMX8MQ_CLK_CSI1_ESC>; |
| assigned-clock-rates = <266000000>, <333000000>, <66000000>; |
| assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_266M>, |
| <&clk IMX8MQ_SYS2_PLL_1000M>, |
| <&clk IMX8MQ_SYS1_PLL_800M>; |
| power-domains = <&pgc_mipi_csi1>; |
| resets = <&src IMX8MQ_RESET_MIPI_CSI1_CORE_RESET>, |
| <&src IMX8MQ_RESET_MIPI_CSI1_PHY_REF_RESET>, |
| <&src IMX8MQ_RESET_MIPI_CSI1_ESC_RESET>; |
| fsl,mipi-phy-gpr = <&iomuxc_gpr 0x88>; |
| interconnects = <&noc IMX8MQ_ICM_CSI1 &noc IMX8MQ_ICS_DRAM>; |
| interconnect-names = "dram"; |
| status = "disabled"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@1 { |
| reg = <1>; |
| |
| csi1_mipi_ep: endpoint { |
| remote-endpoint = <&csi1_ep>; |
| }; |
| }; |
| }; |
| }; |
| |
| csi1: csi@30a90000 { |
| compatible = "fsl,imx8mq-csi"; |
| reg = <0x30a90000 0x10000>; |
| interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MQ_CLK_CSI1_ROOT>; |
| clock-names = "mclk"; |
| status = "disabled"; |
| |
| port { |
| csi1_ep: endpoint { |
| remote-endpoint = <&csi1_mipi_ep>; |
| }; |
| }; |
| }; |
| |
| mipi_csi2: csi@30b60000 { |
| compatible = "fsl,imx8mq-mipi-csi2"; |
| reg = <0x30b60000 0x1000>; |
| clocks = <&clk IMX8MQ_CLK_CSI2_CORE>, |
| <&clk IMX8MQ_CLK_CSI2_ESC>, |
| <&clk IMX8MQ_CLK_CSI2_PHY_REF>; |
| clock-names = "core", "esc", "ui"; |
| assigned-clocks = <&clk IMX8MQ_CLK_CSI2_CORE>, |
| <&clk IMX8MQ_CLK_CSI2_PHY_REF>, |
| <&clk IMX8MQ_CLK_CSI2_ESC>; |
| assigned-clock-rates = <266000000>, <333000000>, <66000000>; |
| assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_266M>, |
| <&clk IMX8MQ_SYS2_PLL_1000M>, |
| <&clk IMX8MQ_SYS1_PLL_800M>; |
| power-domains = <&pgc_mipi_csi2>; |
| resets = <&src IMX8MQ_RESET_MIPI_CSI2_CORE_RESET>, |
| <&src IMX8MQ_RESET_MIPI_CSI2_PHY_REF_RESET>, |
| <&src IMX8MQ_RESET_MIPI_CSI2_ESC_RESET>; |
| fsl,mipi-phy-gpr = <&iomuxc_gpr 0xa4>; |
| interconnects = <&noc IMX8MQ_ICM_CSI2 &noc IMX8MQ_ICS_DRAM>; |
| interconnect-names = "dram"; |
| status = "disabled"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@1 { |
| reg = <1>; |
| |
| csi2_mipi_ep: endpoint { |
| remote-endpoint = <&csi2_ep>; |
| }; |
| }; |
| }; |
| }; |
| |
| csi2: csi@30b80000 { |
| compatible = "fsl,imx8mq-csi"; |
| reg = <0x30b80000 0x10000>; |
| interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MQ_CLK_CSI2_ROOT>; |
| clock-names = "mclk"; |
| status = "disabled"; |
| |
| port { |
| csi2_ep: endpoint { |
| remote-endpoint = <&csi2_mipi_ep>; |
| }; |
| }; |
| }; |
| |
| mu: mailbox@30aa0000 { |
| compatible = "fsl,imx8mq-mu", "fsl,imx6sx-mu"; |
| reg = <0x30aa0000 0x10000>; |
| interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MQ_CLK_MU_ROOT>; |
| #mbox-cells = <2>; |
| }; |
| |
| usdhc1: mmc@30b40000 { |
| compatible = "fsl,imx8mq-usdhc", |
| "fsl,imx7d-usdhc"; |
| reg = <0x30b40000 0x10000>; |
| interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MQ_CLK_IPG_ROOT>, |
| <&clk IMX8MQ_CLK_NAND_USDHC_BUS>, |
| <&clk IMX8MQ_CLK_USDHC1_ROOT>; |
| clock-names = "ipg", "ahb", "per"; |
| fsl,tuning-start-tap = <20>; |
| fsl,tuning-step = <2>; |
| bus-width = <4>; |
| status = "disabled"; |
| }; |
| |
| usdhc2: mmc@30b50000 { |
| compatible = "fsl,imx8mq-usdhc", |
| "fsl,imx7d-usdhc"; |
| reg = <0x30b50000 0x10000>; |
| interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MQ_CLK_IPG_ROOT>, |
| <&clk IMX8MQ_CLK_NAND_USDHC_BUS>, |
| <&clk IMX8MQ_CLK_USDHC2_ROOT>; |
| clock-names = "ipg", "ahb", "per"; |
| fsl,tuning-start-tap = <20>; |
| fsl,tuning-step = <2>; |
| bus-width = <4>; |
| status = "disabled"; |
| }; |
| |
| qspi0: spi@30bb0000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,imx8mq-qspi", "fsl,imx7d-qspi"; |
| reg = <0x30bb0000 0x10000>, |
| <0x08000000 0x10000000>; |
| reg-names = "QuadSPI", "QuadSPI-memory"; |
| interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MQ_CLK_QSPI_ROOT>, |
| <&clk IMX8MQ_CLK_QSPI_ROOT>; |
| clock-names = "qspi_en", "qspi"; |
| status = "disabled"; |
| }; |
| |
| sdma1: dma-controller@30bd0000 { |
| compatible = "fsl,imx8mq-sdma","fsl,imx7d-sdma"; |
| reg = <0x30bd0000 0x10000>; |
| interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MQ_CLK_SDMA1_ROOT>, |
| <&clk IMX8MQ_CLK_AHB>; |
| clock-names = "ipg", "ahb"; |
| #dma-cells = <3>; |
| fsl,sdma-ram-script-name = "imx/sdma/sdma-imx7d.bin"; |
| }; |
| |
| fec1: ethernet@30be0000 { |
| compatible = "fsl,imx8mq-fec", "fsl,imx6sx-fec"; |
| reg = <0x30be0000 0x10000>; |
| interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MQ_CLK_ENET1_ROOT>, |
| <&clk IMX8MQ_CLK_ENET1_ROOT>, |
| <&clk IMX8MQ_CLK_ENET_TIMER>, |
| <&clk IMX8MQ_CLK_ENET_REF>, |
| <&clk IMX8MQ_CLK_ENET_PHY_REF>; |
| clock-names = "ipg", "ahb", "ptp", |
| "enet_clk_ref", "enet_out"; |
| assigned-clocks = <&clk IMX8MQ_CLK_ENET_AXI>, |
| <&clk IMX8MQ_CLK_ENET_TIMER>, |
| <&clk IMX8MQ_CLK_ENET_REF>, |
| <&clk IMX8MQ_CLK_ENET_PHY_REF>; |
| assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_266M>, |
| <&clk IMX8MQ_SYS2_PLL_100M>, |
| <&clk IMX8MQ_SYS2_PLL_125M>, |
| <&clk IMX8MQ_SYS2_PLL_50M>; |
| assigned-clock-rates = <0>, <100000000>, <125000000>, <0>; |
| fsl,num-tx-queues = <3>; |
| fsl,num-rx-queues = <3>; |
| nvmem-cells = <&fec_mac_address>; |
| nvmem-cell-names = "mac-address"; |
| fsl,stop-mode = <&iomuxc_gpr 0x10 3>; |
| status = "disabled"; |
| }; |
| }; |
| |
| noc: interconnect@32700000 { |
| compatible = "fsl,imx8mq-noc", "fsl,imx8m-noc"; |
| reg = <0x32700000 0x100000>; |
| clocks = <&clk IMX8MQ_CLK_NOC>; |
| fsl,ddrc = <&ddrc>; |
| #interconnect-cells = <1>; |
| operating-points-v2 = <&noc_opp_table>; |
| |
| noc_opp_table: opp-table { |
| compatible = "operating-points-v2"; |
| |
| opp-133000000 { |
| opp-hz = /bits/ 64 <133333333>; |
| }; |
| |
| opp-400000000 { |
| opp-hz = /bits/ 64 <400000000>; |
| }; |
| |
| opp-800000000 { |
| opp-hz = /bits/ 64 <800000000>; |
| }; |
| }; |
| }; |
| |
| aips4: bus@32c00000 { /* AIPS4 */ |
| compatible = "fsl,aips-bus", "simple-bus"; |
| reg = <0x32c00000 0x400000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0x32c00000 0x32c00000 0x400000>; |
| |
| irqsteer: interrupt-controller@32e2d000 { |
| compatible = "fsl,imx8m-irqsteer", "fsl,imx-irqsteer"; |
| reg = <0x32e2d000 0x1000>; |
| interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MQ_CLK_DISP_APB_ROOT>; |
| clock-names = "ipg"; |
| fsl,channel = <0>; |
| fsl,num-irqs = <64>; |
| interrupt-controller; |
| #interrupt-cells = <1>; |
| }; |
| }; |
| |
| gpu: gpu@38000000 { |
| compatible = "vivante,gc"; |
| reg = <0x38000000 0x40000>; |
| interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MQ_CLK_GPU_ROOT>, |
| <&clk IMX8MQ_CLK_GPU_SHADER_DIV>, |
| <&clk IMX8MQ_CLK_GPU_AXI>, |
| <&clk IMX8MQ_CLK_GPU_AHB>; |
| clock-names = "core", "shader", "bus", "reg"; |
| #cooling-cells = <2>; |
| assigned-clocks = <&clk IMX8MQ_CLK_GPU_CORE_SRC>, |
| <&clk IMX8MQ_CLK_GPU_SHADER_SRC>, |
| <&clk IMX8MQ_CLK_GPU_AXI>, |
| <&clk IMX8MQ_CLK_GPU_AHB>, |
| <&clk IMX8MQ_GPU_PLL_BYPASS>; |
| assigned-clock-parents = <&clk IMX8MQ_GPU_PLL_OUT>, |
| <&clk IMX8MQ_GPU_PLL_OUT>, |
| <&clk IMX8MQ_GPU_PLL_OUT>, |
| <&clk IMX8MQ_GPU_PLL_OUT>, |
| <&clk IMX8MQ_GPU_PLL>; |
| assigned-clock-rates = <800000000>, <800000000>, |
| <800000000>, <800000000>, <0>; |
| power-domains = <&pgc_gpu>; |
| }; |
| |
| usb_dwc3_0: usb@38100000 { |
| compatible = "fsl,imx8mq-dwc3", "snps,dwc3"; |
| reg = <0x38100000 0x10000>; |
| clocks = <&clk IMX8MQ_CLK_USB1_CTRL_ROOT>, |
| <&clk IMX8MQ_CLK_USB_CORE_REF>, |
| <&clk IMX8MQ_CLK_32K>; |
| clock-names = "bus_early", "ref", "suspend"; |
| assigned-clocks = <&clk IMX8MQ_CLK_USB_BUS>, |
| <&clk IMX8MQ_CLK_USB_CORE_REF>; |
| assigned-clock-parents = <&clk IMX8MQ_SYS2_PLL_500M>, |
| <&clk IMX8MQ_SYS1_PLL_100M>; |
| assigned-clock-rates = <500000000>, <100000000>; |
| interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; |
| phys = <&usb3_phy0>, <&usb3_phy0>; |
| phy-names = "usb2-phy", "usb3-phy"; |
| power-domains = <&pgc_otg1>; |
| snps,parkmode-disable-ss-quirk; |
| status = "disabled"; |
| }; |
| |
| usb3_phy0: usb-phy@381f0040 { |
| compatible = "fsl,imx8mq-usb-phy"; |
| reg = <0x381f0040 0x40>; |
| clocks = <&clk IMX8MQ_CLK_USB1_PHY_ROOT>; |
| clock-names = "phy"; |
| assigned-clocks = <&clk IMX8MQ_CLK_USB_PHY_REF>; |
| assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_100M>; |
| assigned-clock-rates = <100000000>; |
| #phy-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| usb_dwc3_1: usb@38200000 { |
| compatible = "fsl,imx8mq-dwc3", "snps,dwc3"; |
| reg = <0x38200000 0x10000>; |
| clocks = <&clk IMX8MQ_CLK_USB2_CTRL_ROOT>, |
| <&clk IMX8MQ_CLK_USB_CORE_REF>, |
| <&clk IMX8MQ_CLK_32K>; |
| clock-names = "bus_early", "ref", "suspend"; |
| assigned-clocks = <&clk IMX8MQ_CLK_USB_BUS>, |
| <&clk IMX8MQ_CLK_USB_CORE_REF>; |
| assigned-clock-parents = <&clk IMX8MQ_SYS2_PLL_500M>, |
| <&clk IMX8MQ_SYS1_PLL_100M>; |
| assigned-clock-rates = <500000000>, <100000000>; |
| interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; |
| phys = <&usb3_phy1>, <&usb3_phy1>; |
| phy-names = "usb2-phy", "usb3-phy"; |
| power-domains = <&pgc_otg2>; |
| snps,parkmode-disable-ss-quirk; |
| status = "disabled"; |
| }; |
| |
| usb3_phy1: usb-phy@382f0040 { |
| compatible = "fsl,imx8mq-usb-phy"; |
| reg = <0x382f0040 0x40>; |
| clocks = <&clk IMX8MQ_CLK_USB2_PHY_ROOT>; |
| clock-names = "phy"; |
| assigned-clocks = <&clk IMX8MQ_CLK_USB_PHY_REF>; |
| assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_100M>; |
| assigned-clock-rates = <100000000>; |
| #phy-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| vpu_g1: video-codec@38300000 { |
| compatible = "nxp,imx8mq-vpu-g1"; |
| reg = <0x38300000 0x10000>; |
| interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MQ_CLK_VPU_G1_ROOT>; |
| power-domains = <&vpu_blk_ctrl IMX8MQ_VPUBLK_PD_G1>; |
| }; |
| |
| vpu_g2: video-codec@38310000 { |
| compatible = "nxp,imx8mq-vpu-g2"; |
| reg = <0x38310000 0x10000>; |
| interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MQ_CLK_VPU_G2_ROOT>; |
| power-domains = <&vpu_blk_ctrl IMX8MQ_VPUBLK_PD_G2>; |
| }; |
| |
| vpu_blk_ctrl: blk-ctrl@38320000 { |
| compatible = "fsl,imx8mq-vpu-blk-ctrl"; |
| reg = <0x38320000 0x100>; |
| power-domains = <&pgc_vpu>, <&pgc_vpu>, <&pgc_vpu>; |
| power-domain-names = "bus", "g1", "g2"; |
| clocks = <&clk IMX8MQ_CLK_VPU_G1_ROOT>, |
| <&clk IMX8MQ_CLK_VPU_G2_ROOT>; |
| clock-names = "g1", "g2"; |
| #power-domain-cells = <1>; |
| }; |
| |
| pcie0: pcie@33800000 { |
| compatible = "fsl,imx8mq-pcie"; |
| reg = <0x33800000 0x400000>, |
| <0x1ff00000 0x80000>; |
| reg-names = "dbi", "config"; |
| #address-cells = <3>; |
| #size-cells = <2>; |
| device_type = "pci"; |
| bus-range = <0x00 0xff>; |
| ranges = <0x81000000 0 0x00000000 0x1ff80000 0 0x00010000>, /* downstream I/O 64KB */ |
| <0x82000000 0 0x18000000 0x18000000 0 0x07f00000>; /* non-prefetchable memory */ |
| num-lanes = <1>; |
| interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "msi"; |
| #interrupt-cells = <1>; |
| interrupt-map-mask = <0 0 0 0x7>; |
| interrupt-map = <0 0 0 1 &gic GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>, |
| <0 0 0 2 &gic GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>, |
| <0 0 0 3 &gic GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, |
| <0 0 0 4 &gic GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>; |
| fsl,max-link-speed = <2>; |
| linux,pci-domain = <0>; |
| clocks = <&clk IMX8MQ_CLK_PCIE1_ROOT>, |
| <&clk IMX8MQ_CLK_PCIE1_PHY>, |
| <&clk IMX8MQ_CLK_PCIE1_PHY>, |
| <&clk IMX8MQ_CLK_PCIE1_AUX>; |
| clock-names = "pcie", "pcie_bus", "pcie_phy", "pcie_aux"; |
| power-domains = <&pgc_pcie>; |
| resets = <&src IMX8MQ_RESET_PCIEPHY>, |
| <&src IMX8MQ_RESET_PCIE_CTRL_APPS_EN>, |
| <&src IMX8MQ_RESET_PCIE_CTRL_APPS_TURNOFF>; |
| reset-names = "pciephy", "apps", "turnoff"; |
| assigned-clocks = <&clk IMX8MQ_CLK_PCIE1_CTRL>, |
| <&clk IMX8MQ_CLK_PCIE1_PHY>, |
| <&clk IMX8MQ_CLK_PCIE1_AUX>; |
| assigned-clock-parents = <&clk IMX8MQ_SYS2_PLL_250M>, |
| <&clk IMX8MQ_SYS2_PLL_100M>, |
| <&clk IMX8MQ_SYS1_PLL_80M>; |
| assigned-clock-rates = <250000000>, <100000000>, |
| <10000000>; |
| status = "disabled"; |
| }; |
| |
| pcie1: pcie@33c00000 { |
| compatible = "fsl,imx8mq-pcie"; |
| reg = <0x33c00000 0x400000>, |
| <0x27f00000 0x80000>; |
| reg-names = "dbi", "config"; |
| #address-cells = <3>; |
| #size-cells = <2>; |
| device_type = "pci"; |
| bus-range = <0x00 0xff>; |
| ranges = <0x81000000 0 0x00000000 0x27f80000 0 0x00010000>, /* downstream I/O 64KB */ |
| <0x82000000 0 0x20000000 0x20000000 0 0x07f00000>; /* non-prefetchable memory */ |
| num-lanes = <1>; |
| interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "msi"; |
| #interrupt-cells = <1>; |
| interrupt-map-mask = <0 0 0 0x7>; |
| interrupt-map = <0 0 0 1 &gic GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>, |
| <0 0 0 2 &gic GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>, |
| <0 0 0 3 &gic GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>, |
| <0 0 0 4 &gic GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; |
| fsl,max-link-speed = <2>; |
| linux,pci-domain = <1>; |
| clocks = <&clk IMX8MQ_CLK_PCIE2_ROOT>, |
| <&clk IMX8MQ_CLK_PCIE2_PHY>, |
| <&clk IMX8MQ_CLK_PCIE2_PHY>, |
| <&clk IMX8MQ_CLK_PCIE2_AUX>; |
| clock-names = "pcie", "pcie_bus", "pcie_phy", "pcie_aux"; |
| power-domains = <&pgc_pcie>; |
| resets = <&src IMX8MQ_RESET_PCIEPHY2>, |
| <&src IMX8MQ_RESET_PCIE2_CTRL_APPS_EN>, |
| <&src IMX8MQ_RESET_PCIE2_CTRL_APPS_TURNOFF>; |
| reset-names = "pciephy", "apps", "turnoff"; |
| assigned-clocks = <&clk IMX8MQ_CLK_PCIE2_CTRL>, |
| <&clk IMX8MQ_CLK_PCIE2_PHY>, |
| <&clk IMX8MQ_CLK_PCIE2_AUX>; |
| assigned-clock-parents = <&clk IMX8MQ_SYS2_PLL_250M>, |
| <&clk IMX8MQ_SYS2_PLL_100M>, |
| <&clk IMX8MQ_SYS1_PLL_80M>; |
| assigned-clock-rates = <250000000>, <100000000>, |
| <10000000>; |
| status = "disabled"; |
| }; |
| |
| pcie1_ep: pcie-ep@33c00000 { |
| compatible = "fsl,imx8mq-pcie-ep"; |
| reg = <0x33c00000 0x000400000>, |
| <0x20000000 0x08000000>; |
| reg-names = "dbi", "addr_space"; |
| num-lanes = <1>; |
| interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "dma"; |
| fsl,max-link-speed = <2>; |
| clocks = <&clk IMX8MQ_CLK_PCIE2_ROOT>, |
| <&clk IMX8MQ_CLK_PCIE2_PHY>, |
| <&clk IMX8MQ_CLK_PCIE2_PHY>, |
| <&clk IMX8MQ_CLK_PCIE2_AUX>; |
| clock-names = "pcie", "pcie_bus", "pcie_phy", "pcie_aux"; |
| power-domains = <&pgc_pcie>; |
| resets = <&src IMX8MQ_RESET_PCIEPHY2>, |
| <&src IMX8MQ_RESET_PCIE2_CTRL_APPS_EN>, |
| <&src IMX8MQ_RESET_PCIE2_CTRL_APPS_TURNOFF>; |
| reset-names = "pciephy", "apps", "turnoff"; |
| assigned-clocks = <&clk IMX8MQ_CLK_PCIE2_CTRL>, |
| <&clk IMX8MQ_CLK_PCIE2_PHY>, |
| <&clk IMX8MQ_CLK_PCIE2_AUX>; |
| assigned-clock-parents = <&clk IMX8MQ_SYS2_PLL_250M>, |
| <&clk IMX8MQ_SYS2_PLL_100M>, |
| <&clk IMX8MQ_SYS1_PLL_80M>; |
| assigned-clock-rates = <250000000>, <100000000>, |
| <10000000>; |
| num-ib-windows = <4>; |
| num-ob-windows = <4>; |
| status = "disabled"; |
| }; |
| |
| gic: interrupt-controller@38800000 { |
| compatible = "arm,gic-v3"; |
| reg = <0x38800000 0x10000>, /* GIC Dist */ |
| <0x38880000 0xc0000>, /* GICR */ |
| <0x31000000 0x2000>, /* GICC */ |
| <0x31010000 0x2000>, /* GICV */ |
| <0x31020000 0x2000>; /* GICH */ |
| #interrupt-cells = <3>; |
| interrupt-controller; |
| interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-parent = <&gic>; |
| }; |
| |
| ddrc: memory-controller@3d400000 { |
| compatible = "fsl,imx8mq-ddrc", "fsl,imx8m-ddrc"; |
| reg = <0x3d400000 0x400000>; |
| clock-names = "core", "pll", "alt", "apb"; |
| clocks = <&clk IMX8MQ_CLK_DRAM_CORE>, |
| <&clk IMX8MQ_DRAM_PLL_OUT>, |
| <&clk IMX8MQ_CLK_DRAM_ALT>, |
| <&clk IMX8MQ_CLK_DRAM_APB>; |
| status = "disabled"; |
| }; |
| |
| ddr-pmu@3d800000 { |
| compatible = "fsl,imx8mq-ddr-pmu", "fsl,imx8m-ddr-pmu"; |
| reg = <0x3d800000 0x400000>; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| }; |
| }; |
