| Broadcom iProc Family Clocks |
| |
| This binding uses the common clock binding: |
| Documentation/devicetree/bindings/clock/clock-bindings.txt |
| |
| The iProc clock controller manages clocks that are common to the iProc family. |
| An SoC from the iProc family may have several PPLs, e.g., ARMPLL, GENPLL, |
| LCPLL0, MIPIPLL, and etc., all derived from an onboard crystal. Each PLL |
| comprises of several leaf clocks |
| |
| Required properties for a PLL and its leaf clocks: |
| |
| - compatible: |
| Should have a value of the form "brcm,<soc>-<pll>". For example, GENPLL on |
| Cygnus has a compatible string of "brcm,cygnus-genpll" |
| |
| - #clock-cells: |
| Have a value of <1> since there are more than 1 leaf clock of a given PLL |
| |
| - reg: |
| Define the base and range of the I/O address space that contain the iProc |
| clock control registers required for the PLL |
| |
| - clocks: |
| The input parent clock phandle for the PLL. For most iProc PLLs, this is an |
| onboard crystal with a fixed rate |
| |
| - clock-output-names: |
| An ordered list of strings defining the names of the clocks |
| |
| Example: |
| |
| osc: oscillator { |
| #clock-cells = <0>; |
| compatible = "fixed-clock"; |
| clock-frequency = <25000000>; |
| }; |
| |
| genpll: genpll { |
| #clock-cells = <1>; |
| compatible = "brcm,cygnus-genpll"; |
| reg = <0x0301d000 0x2c>, <0x0301c020 0x4>; |
| clocks = <&osc>; |
| clock-output-names = "genpll", "axi21", "250mhz", "ihost_sys", |
| "enet_sw", "audio_125", "can"; |
| }; |
| |
| Required properties for ASIU clocks: |
| |
| ASIU clocks are a special case. These clocks are derived directly from the |
| reference clock of the onboard crystal |
| |
| - compatible: |
| Should have a value of the form "brcm,<soc>-asiu-clk". For example, ASIU |
| clocks for Cygnus have a compatible string of "brcm,cygnus-asiu-clk" |
| |
| - #clock-cells: |
| Have a value of <1> since there are more than 1 ASIU clocks |
| |
| - reg: |
| Define the base and range of the I/O address space that contain the iProc |
| clock control registers required for ASIU clocks |
| |
| - clocks: |
| The input parent clock phandle for the ASIU clock, i.e., the onboard |
| crystal |
| |
| - clock-output-names: |
| An ordered list of strings defining the names of the ASIU clocks |
| |
| Example: |
| |
| osc: oscillator { |
| #clock-cells = <0>; |
| compatible = "fixed-clock"; |
| clock-frequency = <25000000>; |
| }; |
| |
| asiu_clks: asiu_clks { |
| #clock-cells = <1>; |
| compatible = "brcm,cygnus-asiu-clk"; |
| reg = <0x0301d048 0xc>, <0x180aa024 0x4>; |
| clocks = <&osc>; |
| clock-output-names = "keypad", "adc/touch", "pwm"; |
| }; |
| |
| Cygnus |
| ------ |
| PLL and leaf clock compatible strings for Cygnus are: |
| "brcm,cygnus-armpll" |
| "brcm,cygnus-genpll" |
| "brcm,cygnus-lcpll0" |
| "brcm,cygnus-mipipll" |
| "brcm,cygnus-asiu-clk" |
| "brcm,cygnus-audiopll" |
| |
| The following table defines the set of PLL/clock index and ID for Cygnus. |
| These clock IDs are defined in: |
| "include/dt-bindings/clock/bcm-cygnus.h" |
| |
| Clock Source (Parent) Index ID |
| --- ----- ----- --------- |
| crystal N/A N/A N/A |
| |
| armpll crystal N/A N/A |
| |
| keypad crystal (ASIU) 0 BCM_CYGNUS_ASIU_KEYPAD_CLK |
| adc/tsc crystal (ASIU) 1 BCM_CYGNUS_ASIU_ADC_CLK |
| pwm crystal (ASIU) 2 BCM_CYGNUS_ASIU_PWM_CLK |
| |
| genpll crystal 0 BCM_CYGNUS_GENPLL |
| axi21 genpll 1 BCM_CYGNUS_GENPLL_AXI21_CLK |
| 250mhz genpll 2 BCM_CYGNUS_GENPLL_250MHZ_CLK |
| ihost_sys genpll 3 BCM_CYGNUS_GENPLL_IHOST_SYS_CLK |
| enet_sw genpll 4 BCM_CYGNUS_GENPLL_ENET_SW_CLK |
| audio_125 genpll 5 BCM_CYGNUS_GENPLL_AUDIO_125_CLK |
| can genpll 6 BCM_CYGNUS_GENPLL_CAN_CLK |
| |
| lcpll0 crystal 0 BCM_CYGNUS_LCPLL0 |
| pcie_phy lcpll0 1 BCM_CYGNUS_LCPLL0_PCIE_PHY_REF_CLK |
| ddr_phy lcpll0 2 BCM_CYGNUS_LCPLL0_DDR_PHY_CLK |
| sdio lcpll0 3 BCM_CYGNUS_LCPLL0_SDIO_CLK |
| usb_phy lcpll0 4 BCM_CYGNUS_LCPLL0_USB_PHY_REF_CLK |
| smart_card lcpll0 5 BCM_CYGNUS_LCPLL0_SMART_CARD_CLK |
| ch5_unused lcpll0 6 BCM_CYGNUS_LCPLL0_CH5_UNUSED |
| |
| mipipll crystal 0 BCM_CYGNUS_MIPIPLL |
| ch0_unused mipipll 1 BCM_CYGNUS_MIPIPLL_CH0_UNUSED |
| ch1_lcd mipipll 2 BCM_CYGNUS_MIPIPLL_CH1_LCD |
| ch2_v3d mipipll 3 BCM_CYGNUS_MIPIPLL_CH2_V3D |
| ch3_unused mipipll 4 BCM_CYGNUS_MIPIPLL_CH3_UNUSED |
| ch4_unused mipipll 5 BCM_CYGNUS_MIPIPLL_CH4_UNUSED |
| ch5_unused mipipll 6 BCM_CYGNUS_MIPIPLL_CH5_UNUSED |
| |
| audiopll crystal 0 BCM_CYGNUS_AUDIOPLL |
| ch0_audio audiopll 1 BCM_CYGNUS_AUDIOPLL_CH0 |
| ch1_audio audiopll 2 BCM_CYGNUS_AUDIOPLL_CH1 |
| ch2_audio audiopll 3 BCM_CYGNUS_AUDIOPLL_CH2 |
| |
| Hurricane 2 |
| ------ |
| PLL and leaf clock compatible strings for Hurricane 2 are: |
| "brcm,hr2-armpll" |
| |
| The following table defines the set of PLL/clock for Hurricane 2: |
| |
| Clock Source Index ID |
| --- ----- ----- --------- |
| crystal N/A N/A N/A |
| |
| armpll crystal N/A N/A |
| |
| |
| Northstar and Northstar Plus |
| ------ |
| PLL and leaf clock compatible strings for Northstar and Northstar Plus are: |
| "brcm,nsp-armpll" |
| "brcm,nsp-genpll" |
| "brcm,nsp-lcpll0" |
| |
| The following table defines the set of PLL/clock index and ID for Northstar and |
| Northstar Plus. These clock IDs are defined in: |
| "include/dt-bindings/clock/bcm-nsp.h" |
| |
| Clock Source Index ID |
| --- ----- ----- --------- |
| crystal N/A N/A N/A |
| |
| armpll crystal N/A N/A |
| |
| genpll crystal 0 BCM_NSP_GENPLL |
| phy genpll 1 BCM_NSP_GENPLL_PHY_CLK |
| ethernetclk genpll 2 BCM_NSP_GENPLL_ENET_SW_CLK |
| usbclk genpll 3 BCM_NSP_GENPLL_USB_PHY_REF_CLK |
| iprocfast genpll 4 BCM_NSP_GENPLL_IPROCFAST_CLK |
| sata1 genpll 5 BCM_NSP_GENPLL_SATA1_CLK |
| sata2 genpll 6 BCM_NSP_GENPLL_SATA2_CLK |
| |
| lcpll0 crystal 0 BCM_NSP_LCPLL0 |
| pcie_phy lcpll0 1 BCM_NSP_LCPLL0_PCIE_PHY_REF_CLK |
| sdio lcpll0 2 BCM_NSP_LCPLL0_SDIO_CLK |
| ddr_phy lcpll0 3 BCM_NSP_LCPLL0_DDR_PHY_CLK |
| |
| Northstar 2 |
| ----------- |
| PLL and leaf clock compatible strings for Northstar 2 are: |
| "brcm,ns2-genpll-scr" |
| "brcm,ns2-genpll-sw" |
| "brcm,ns2-lcpll-ddr" |
| "brcm,ns2-lcpll-ports" |
| |
| The following table defines the set of PLL/clock index and ID for Northstar 2. |
| These clock IDs are defined in: |
| "include/dt-bindings/clock/bcm-ns2.h" |
| |
| Clock Source Index ID |
| --- ----- ----- --------- |
| crystal N/A N/A N/A |
| |
| genpll_scr crystal 0 BCM_NS2_GENPLL_SCR |
| scr genpll_scr 1 BCM_NS2_GENPLL_SCR_SCR_CLK |
| fs genpll_scr 2 BCM_NS2_GENPLL_SCR_FS_CLK |
| audio_ref genpll_scr 3 BCM_NS2_GENPLL_SCR_AUDIO_CLK |
| ch3_unused genpll_scr 4 BCM_NS2_GENPLL_SCR_CH3_UNUSED |
| ch4_unused genpll_scr 5 BCM_NS2_GENPLL_SCR_CH4_UNUSED |
| ch5_unused genpll_scr 6 BCM_NS2_GENPLL_SCR_CH5_UNUSED |
| |
| genpll_sw crystal 0 BCM_NS2_GENPLL_SW |
| rpe genpll_sw 1 BCM_NS2_GENPLL_SW_RPE_CLK |
| 250 genpll_sw 2 BCM_NS2_GENPLL_SW_250_CLK |
| nic genpll_sw 3 BCM_NS2_GENPLL_SW_NIC_CLK |
| chimp genpll_sw 4 BCM_NS2_GENPLL_SW_CHIMP_CLK |
| port genpll_sw 5 BCM_NS2_GENPLL_SW_PORT_CLK |
| sdio genpll_sw 6 BCM_NS2_GENPLL_SW_SDIO_CLK |
| |
| lcpll_ddr crystal 0 BCM_NS2_LCPLL_DDR |
| pcie_sata_usb lcpll_ddr 1 BCM_NS2_LCPLL_DDR_PCIE_SATA_USB_CLK |
| ddr lcpll_ddr 2 BCM_NS2_LCPLL_DDR_DDR_CLK |
| ch2_unused lcpll_ddr 3 BCM_NS2_LCPLL_DDR_CH2_UNUSED |
| ch3_unused lcpll_ddr 4 BCM_NS2_LCPLL_DDR_CH3_UNUSED |
| ch4_unused lcpll_ddr 5 BCM_NS2_LCPLL_DDR_CH4_UNUSED |
| ch5_unused lcpll_ddr 6 BCM_NS2_LCPLL_DDR_CH5_UNUSED |
| |
| lcpll_ports crystal 0 BCM_NS2_LCPLL_PORTS |
| wan lcpll_ports 1 BCM_NS2_LCPLL_PORTS_WAN_CLK |
| rgmii lcpll_ports 2 BCM_NS2_LCPLL_PORTS_RGMII_CLK |
| ch2_unused lcpll_ports 3 BCM_NS2_LCPLL_PORTS_CH2_UNUSED |
| ch3_unused lcpll_ports 4 BCM_NS2_LCPLL_PORTS_CH3_UNUSED |
| ch4_unused lcpll_ports 5 BCM_NS2_LCPLL_PORTS_CH4_UNUSED |
| ch5_unused lcpll_ports 6 BCM_NS2_LCPLL_PORTS_CH5_UNUSED |
| |
| BCM63138 |
| -------- |
| PLL and leaf clock compatible strings for BCM63138 are: |
| "brcm,bcm63138-armpll" |
| |
| Stingray |
| ----------- |
| PLL and leaf clock compatible strings for Stingray are: |
| "brcm,sr-genpll0" |
| "brcm,sr-genpll1" |
| "brcm,sr-genpll2" |
| "brcm,sr-genpll3" |
| "brcm,sr-genpll4" |
| "brcm,sr-genpll5" |
| "brcm,sr-genpll6" |
| |
| "brcm,sr-lcpll0" |
| "brcm,sr-lcpll1" |
| "brcm,sr-lcpll-pcie" |
| |
| |
| The following table defines the set of PLL/clock index and ID for Stingray. |
| These clock IDs are defined in: |
| "include/dt-bindings/clock/bcm-sr.h" |
| |
| Clock Source Index ID |
| --- ----- ----- --------- |
| crystal N/A N/A N/A |
| crmu_ref25m crystal N/A N/A |
| |
| genpll0 crystal 0 BCM_SR_GENPLL0 |
| clk_125m genpll0 1 BCM_SR_GENPLL0_125M_CLK |
| clk_scr genpll0 2 BCM_SR_GENPLL0_SCR_CLK |
| clk_250 genpll0 3 BCM_SR_GENPLL0_250M_CLK |
| clk_pcie_axi genpll0 4 BCM_SR_GENPLL0_PCIE_AXI_CLK |
| clk_paxc_axi_x2 genpll0 5 BCM_SR_GENPLL0_PAXC_AXI_X2_CLK |
| clk_paxc_axi genpll0 6 BCM_SR_GENPLL0_PAXC_AXI_CLK |
| |
| genpll1 crystal 0 BCM_SR_GENPLL1 |
| clk_pcie_tl genpll1 1 BCM_SR_GENPLL1_PCIE_TL_CLK |
| clk_mhb_apb genpll1 2 BCM_SR_GENPLL1_MHB_APB_CLK |
| |
| genpll2 crystal 0 BCM_SR_GENPLL2 |
| clk_nic genpll2 1 BCM_SR_GENPLL2_NIC_CLK |
| clk_ts_500_ref genpll2 2 BCM_SR_GENPLL2_TS_500_REF_CLK |
| clk_125_nitro genpll2 3 BCM_SR_GENPLL2_125_NITRO_CLK |
| clk_chimp genpll2 4 BCM_SR_GENPLL2_CHIMP_CLK |
| clk_nic_flash genpll2 5 BCM_SR_GENPLL2_NIC_FLASH |
| |
| genpll3 crystal 0 BCM_SR_GENPLL3 |
| clk_hsls genpll3 1 BCM_SR_GENPLL3_HSLS_CLK |
| clk_sdio genpll3 2 BCM_SR_GENPLL3_SDIO_CLK |
| |
| genpll4 crystal 0 BCM_SR_GENPLL4 |
| ccn genpll4 1 BCM_SR_GENPLL4_CCN_CLK |
| clk_tpiu_pll genpll4 2 BCM_SR_GENPLL4_TPIU_PLL_CLK |
| noc_clk genpll4 3 BCM_SR_GENPLL4_NOC_CLK |
| clk_chclk_fs4 genpll4 4 BCM_SR_GENPLL4_CHCLK_FS4_CLK |
| clk_bridge_fscpu genpll4 5 BCM_SR_GENPLL4_BRIDGE_FSCPU_CLK |
| |
| |
| genpll5 crystal 0 BCM_SR_GENPLL5 |
| fs4_hf_clk genpll5 1 BCM_SR_GENPLL5_FS4_HF_CLK |
| crypto_ae_clk genpll5 2 BCM_SR_GENPLL5_CRYPTO_AE_CLK |
| raid_ae_clk genpll5 3 BCM_SR_GENPLL5_RAID_AE_CLK |
| |
| genpll6 crystal 0 BCM_SR_GENPLL6 |
| 48_usb genpll6 1 BCM_SR_GENPLL6_48_USB_CLK |
| |
| lcpll0 crystal 0 BCM_SR_LCPLL0 |
| clk_sata_refp lcpll0 1 BCM_SR_LCPLL0_SATA_REFP_CLK |
| clk_sata_refn lcpll0 2 BCM_SR_LCPLL0_SATA_REFN_CLK |
| clk_usb_ref lcpll0 3 BCM_SR_LCPLL0_USB_REF_CLK |
| sata_refpn lcpll0 3 BCM_SR_LCPLL0_SATA_REFPN_CLK |
| |
| lcpll1 crystal 0 BCM_SR_LCPLL1 |
| wan lcpll1 1 BCM_SR_LCPLL0_WAN_CLK |
| |
| lcpll_pcie crystal 0 BCM_SR_LCPLL_PCIE |
| pcie_phy_ref lcpll1 1 BCM_SR_LCPLL_PCIE_PHY_REF_CLK |
