| // SPDX-License-Identifier: BSD-3-Clause |
| /* |
| * Copyright (c) 2021, AngeloGioacchino Del Regno |
| * <angelogioacchino.delregno@somainline.org> |
| * Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org> |
| */ |
| |
| #include <dt-bindings/input/input.h> |
| #include <dt-bindings/leds/common.h> |
| #include <dt-bindings/pinctrl/qcom,pmic-gpio.h> |
| #include "msm8998.dtsi" |
| #include "pm8005.dtsi" |
| #include "pm8998.dtsi" |
| #include "pmi8998.dtsi" |
| |
| / { |
| /* required for bootloader to select correct board */ |
| qcom,msm-id = <0x124 0x20000>, <0x124 0x20001>; /* 8998v2, v2.1 */ |
| qcom,board-id = <8 0>; |
| |
| clocks { |
| div1_mclk: divclk1 { |
| compatible = "gpio-gate-clock"; |
| pinctrl-0 = <&audio_mclk_pin>; |
| pinctrl-names = "default"; |
| clocks = <&rpmcc RPM_SMD_DIV_CLK1>; |
| #clock-cells = <0>; |
| enable-gpios = <&pm8998_gpios 13 GPIO_ACTIVE_HIGH>; |
| }; |
| }; |
| |
| board_vbat: vbat-regulator { |
| compatible = "regulator-fixed"; |
| regulator-name = "VBAT"; |
| |
| regulator-min-microvolt = <4000000>; |
| regulator-max-microvolt = <4000000>; |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| cam0_vdig_vreg: cam0-vdig { |
| compatible = "regulator-fixed"; |
| regulator-name = "cam0_vdig"; |
| startup-delay-us = <0>; |
| enable-active-high; |
| gpio = <&tlmm 21 GPIO_ACTIVE_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&cam0_vdig_default>; |
| }; |
| |
| cam1_vdig_vreg: cam1-vdig { |
| compatible = "regulator-fixed"; |
| regulator-name = "cam1_vdig"; |
| startup-delay-us = <0>; |
| enable-active-high; |
| gpio = <&tlmm 25 GPIO_ACTIVE_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&cam1_vdig_default>; |
| vin-supply = <&vreg_s3a_1p35>; |
| }; |
| |
| cam_vio_vreg: cam-vio-vreg { |
| compatible = "regulator-fixed"; |
| regulator-name = "cam_vio_vreg"; |
| startup-delay-us = <0>; |
| enable-active-high; |
| gpio = <&pmi8998_gpios 1 GPIO_ACTIVE_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&cam_vio_default>; |
| vin-supply = <&vreg_lvs1a_1p8>; |
| }; |
| |
| touch_vddio_vreg: touch-vddio-vreg { |
| compatible = "regulator-fixed"; |
| regulator-name = "touch_vddio_vreg"; |
| startup-delay-us = <10000>; |
| gpio = <&tlmm 133 GPIO_ACTIVE_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&ts_vddio_en>; |
| }; |
| |
| vph_pwr: vph-pwr-regulator { |
| compatible = "regulator-fixed"; |
| regulator-name = "vph_pwr"; |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| extcon_usb: extcon-usb { |
| compatible = "linux,extcon-usb-gpio"; |
| id-gpio = <&tlmm 38 GPIO_ACTIVE_HIGH>; |
| vbus-gpio = <&tlmm 128 GPIO_ACTIVE_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&usb_extcon_active &usb_vbus_active>; |
| }; |
| |
| gpio-keys { |
| compatible = "gpio-keys"; |
| label = "Side buttons"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&vol_down_pin_a>, <&cam_focus_pin_a>, |
| <&cam_snapshot_pin_a>; |
| button-vol-down { |
| label = "Volume Down"; |
| gpios = <&pm8998_gpios 5 GPIO_ACTIVE_LOW>; |
| linux,input-type = <EV_KEY>; |
| linux,code = <KEY_VOLUMEDOWN>; |
| gpio-key,wakeup; |
| debounce-interval = <15>; |
| }; |
| |
| button-camera-snapshot { |
| label = "Camera Snapshot"; |
| gpios = <&pm8998_gpios 7 GPIO_ACTIVE_LOW>; |
| linux,input-type = <EV_KEY>; |
| linux,code = <KEY_CAMERA>; |
| debounce-interval = <15>; |
| }; |
| |
| button-camera-focus { |
| label = "Camera Focus"; |
| gpios = <&pm8998_gpios 8 GPIO_ACTIVE_LOW>; |
| linux,input-type = <EV_KEY>; |
| linux,code = <KEY_CAMERA_FOCUS>; |
| debounce-interval = <15>; |
| }; |
| }; |
| |
| gpio-hall-sensor { |
| compatible = "gpio-keys"; |
| label = "Hall sensors"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&hall_sensor0_default>; |
| |
| event-hall-sensor0 { |
| label = "Cover Hall Sensor"; |
| gpios = <&tlmm 124 GPIO_ACTIVE_LOW>; |
| linux,input-type = <EV_SW>; |
| linux,code = <SW_LID>; |
| gpio-key,wakeup; |
| debounce-interval = <30>; |
| }; |
| }; |
| |
| reserved-memory { |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| |
| hyp_mem: memory@85800000 { |
| reg = <0x0 0x85800000 0x0 0x3700000>; |
| no-map; |
| }; |
| |
| cont_splash_mem: memory@9d400000 { |
| reg = <0x0 0x9d400000 0x0 0x2400000>; |
| no-map; |
| }; |
| |
| zap_shader_region: memory@f6400000 { |
| compatible = "shared-dma-pool"; |
| reg = <0x0 0xf6400000 0x0 0x2000>; |
| no-map; |
| }; |
| |
| adsp_region: memory@fe000000 { |
| reg = <0x0 0xfe000000 0x0 0x800000>; |
| no-map; |
| }; |
| |
| qseecom_region: memory@fe800000 { |
| reg = <0x0 0xfe800000 0x0 0x1400000>; |
| no-map; |
| }; |
| |
| ramoops@ffc00000 { |
| compatible = "ramoops"; |
| reg = <0x0 0xffc00000 0x0 0x100000>; |
| record-size = <0x10000>; |
| console-size = <0x60000>; |
| ftrace-size = <0x10000>; |
| pmsg-size = <0x20000>; |
| ecc-size = <16>; |
| }; |
| }; |
| |
| vibrator { |
| compatible = "gpio-vibrator"; |
| enable-gpios = <&pmi8998_gpios 5 GPIO_ACTIVE_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&vib_default>; |
| }; |
| }; |
| |
| &blsp1_i2c5 { |
| status = "okay"; |
| clock-frequency = <355000>; |
| |
| touchscreen@2c { |
| compatible = "syna,rmi4-i2c"; |
| reg = <0x2c>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| interrupts-extended = <&tlmm 125 IRQ_TYPE_EDGE_FALLING>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&ts_int_n>; |
| |
| vdd-supply = <&vreg_l28_3p0>; |
| vio-supply = <&touch_vddio_vreg>; |
| |
| syna,reset-delay-ms = <220>; |
| syna,startup-delay-ms = <1000>; |
| |
| rmi4-f01@1 { |
| reg = <0x01>; |
| syna,nosleep-mode = <1>; |
| }; |
| |
| rmi4-f11@11 { |
| reg = <0x11>; |
| syna,sensor-type = <1>; |
| }; |
| }; |
| }; |
| |
| &blsp1_i2c5_sleep { |
| bias-disable; |
| }; |
| |
| &blsp1_uart3 { |
| status = "okay"; |
| |
| bluetooth { |
| compatible = "qcom,wcn3990-bt"; |
| |
| vddio-supply = <&vreg_s4a_1p8>; |
| vddxo-supply = <&vreg_l7a_1p8>; |
| vddrf-supply = <&vreg_l17a_1p3>; |
| vddch0-supply = <&vreg_l25a_3p3>; |
| max-speed = <3200000>; |
| |
| clocks = <&rpmcc RPM_SMD_RF_CLK2_PIN>; |
| }; |
| }; |
| |
| &blsp2_uart1 { |
| status = "okay"; |
| }; |
| |
| &blsp2_i2c2 { |
| status = "okay"; |
| |
| proximity@29 { |
| compatible = "st,vl53l0x"; |
| reg = <0x29>; |
| |
| interrupt-parent = <&tlmm>; |
| interrupts = <22 IRQ_TYPE_EDGE_FALLING>; |
| |
| reset-gpios = <&tlmm 27 GPIO_ACTIVE_LOW>; |
| vdd-supply = <&cam_vio_vreg>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&tof_int &tof_reset>; |
| }; |
| }; |
| |
| &ibb { |
| regulator-min-microamp = <800000>; |
| regulator-max-microamp = <800000>; |
| regulator-enable-ramp-delay = <200>; |
| regulator-over-current-protection; |
| regulator-pull-down; |
| regulator-ramp-delay = <1>; |
| regulator-settling-time-up-us = <600>; |
| regulator-settling-time-down-us = <1000>; |
| regulator-soft-start; |
| qcom,discharge-resistor-kohms = <300>; |
| }; |
| |
| &lab { |
| regulator-min-microamp = <200000>; |
| regulator-max-microamp = <200000>; |
| regulator-enable-ramp-delay = <500>; |
| regulator-over-current-protection; |
| regulator-pull-down; |
| regulator-ramp-delay = <1>; |
| regulator-settling-time-up-us = <50000>; |
| regulator-settling-time-down-us = <3000>; |
| regulator-soft-start; |
| }; |
| |
| &pm8005_regulators { |
| /* VDD_GFX supply */ |
| pm8005_s1: s1 { |
| regulator-min-microvolt = <524000>; |
| regulator-max-microvolt = <1088000>; |
| regulator-enable-ramp-delay = <500>; |
| /* Hack until we rig up the gpu consumer */ |
| regulator-always-on; |
| }; |
| }; |
| |
| &pm8998_gpios { |
| vol_down_pin_a: vol-down-active-state { |
| pins = "gpio5"; |
| function = PMIC_GPIO_FUNC_NORMAL; |
| bias-pull-up; |
| input-enable; |
| qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>; |
| }; |
| |
| cam_focus_pin_a: cam-focus-btn-active-state { |
| pins = "gpio7"; |
| function = PMIC_GPIO_FUNC_NORMAL; |
| bias-pull-up; |
| input-enable; |
| qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>; |
| }; |
| |
| cam_snapshot_pin_a: cam-snapshot-btn-active-state { |
| pins = "gpio8"; |
| function = PMIC_GPIO_FUNC_NORMAL; |
| bias-pull-up; |
| input-enable; |
| qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>; |
| }; |
| |
| audio_mclk_pin: audio-mclk-pin-active-state { |
| pins = "gpio13"; |
| function = "func2"; |
| power-source = <0>; |
| }; |
| }; |
| |
| &pmi8998_gpios { |
| cam_vio_default: cam-vio-active-state { |
| pins = "gpio1"; |
| function = PMIC_GPIO_FUNC_NORMAL; |
| bias-disable; |
| drive-push-pull; |
| output-low; |
| qcom,drive-strength = <PMIC_GPIO_STRENGTH_HIGH>; |
| power-source = <1>; |
| }; |
| |
| vib_default: vib-en-state { |
| pins = "gpio5"; |
| function = PMIC_GPIO_FUNC_NORMAL; |
| bias-disable; |
| drive-push-pull; |
| output-low; |
| qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>; |
| power-source = <0>; |
| }; |
| }; |
| |
| &pm8998_resin { |
| linux,code = <KEY_VOLUMEUP>; |
| status = "okay"; |
| }; |
| |
| &qusb2phy { |
| status = "okay"; |
| |
| vdda-pll-supply = <&vreg_l12a_1p8>; |
| vdda-phy-dpdm-supply = <&vreg_l24a_3p075>; |
| }; |
| |
| &rpm_requests { |
| regulators-0 { |
| compatible = "qcom,rpm-pm8998-regulators"; |
| |
| vdd_s1-supply = <&vph_pwr>; |
| vdd_s2-supply = <&vph_pwr>; |
| vdd_s3-supply = <&vph_pwr>; |
| vdd_s4-supply = <&vph_pwr>; |
| vdd_s5-supply = <&vph_pwr>; |
| vdd_s6-supply = <&vph_pwr>; |
| vdd_s7-supply = <&vph_pwr>; |
| vdd_s8-supply = <&vph_pwr>; |
| vdd_s9-supply = <&vph_pwr>; |
| vdd_s10-supply = <&vph_pwr>; |
| vdd_s11-supply = <&vph_pwr>; |
| vdd_s12-supply = <&vph_pwr>; |
| vdd_s13-supply = <&vph_pwr>; |
| vdd_l1_l27-supply = <&vreg_s7a_1p025>; |
| vdd_l2_l8_l17-supply = <&vreg_s3a_1p35>; |
| vdd_l3_l11-supply = <&vreg_s7a_1p025>; |
| vdd_l4_l5-supply = <&vreg_s7a_1p025>; |
| vdd_l6-supply = <&vreg_s5a_2p04>; |
| vdd_l7_l12_l14_l15-supply = <&vreg_s5a_2p04>; |
| vdd_l9-supply = <&vreg_bob>; |
| vdd_l10_l23_l25-supply = <&vreg_bob>; |
| vdd_l13_l19_l21-supply = <&vreg_bob>; |
| vdd_l16_l28-supply = <&vreg_bob>; |
| vdd_l18_l22-supply = <&vreg_bob>; |
| vdd_l20_l24-supply = <&vreg_bob>; |
| vdd_l26-supply = <&vreg_s3a_1p35>; |
| vdd_lvs1_lvs2-supply = <&vreg_s4a_1p8>; |
| |
| vreg_s3a_1p35: s3 { |
| regulator-min-microvolt = <1352000>; |
| regulator-max-microvolt = <1352000>; |
| }; |
| |
| vreg_s4a_1p8: s4 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-system-load = <100000>; |
| regulator-allow-set-load; |
| }; |
| |
| vreg_s5a_2p04: s5 { |
| regulator-min-microvolt = <1904000>; |
| regulator-max-microvolt = <2032000>; |
| }; |
| |
| vreg_s7a_1p025: s7 { |
| regulator-min-microvolt = <900000>; |
| regulator-max-microvolt = <1028000>; |
| }; |
| |
| vreg_l1a_0p875: l1 { |
| regulator-min-microvolt = <880000>; |
| regulator-max-microvolt = <880000>; |
| regulator-system-load = <73400>; |
| regulator-allow-set-load; |
| }; |
| |
| vreg_l2a_1p2: l2 { |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| regulator-system-load = <12560>; |
| regulator-allow-set-load; |
| }; |
| |
| vreg_l3a_1p0: l3 { |
| regulator-min-microvolt = <1000000>; |
| regulator-max-microvolt = <1000000>; |
| }; |
| |
| vreg_l5a_0p8: l5 { |
| regulator-min-microvolt = <800000>; |
| regulator-max-microvolt = <800000>; |
| }; |
| |
| vreg_l6a_1p8: l6 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| vreg_l7a_1p8: l7 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| vreg_l8a_1p2: l8 { |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| }; |
| |
| vreg_l9a_1p8: l9 { |
| regulator-min-microvolt = <1808000>; |
| regulator-max-microvolt = <2960000>; |
| }; |
| |
| vreg_l10a_1p8: l10 { |
| regulator-min-microvolt = <1808000>; |
| regulator-max-microvolt = <2960000>; |
| }; |
| |
| vreg_l11a_1p0: l11 { |
| regulator-min-microvolt = <1000000>; |
| regulator-max-microvolt = <1000000>; |
| }; |
| |
| vreg_l12a_1p8: l12 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| vreg_l13a_2p95: l13 { |
| regulator-min-microvolt = <1808000>; |
| regulator-max-microvolt = <2960000>; |
| regulator-allow-set-load; |
| }; |
| |
| vreg_l14a_1p85: l14 { |
| regulator-min-microvolt = <1848000>; |
| regulator-max-microvolt = <1856000>; |
| regulator-system-load = <32000>; |
| regulator-allow-set-load; |
| }; |
| |
| vreg_l15a_1p8: l15 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| vreg_l16a_2p7: l16 { |
| regulator-min-microvolt = <2704000>; |
| regulator-max-microvolt = <2704000>; |
| }; |
| |
| vreg_l17a_1p3: l17 { |
| regulator-min-microvolt = <1304000>; |
| regulator-max-microvolt = <1304000>; |
| }; |
| |
| vreg_l18a_2p85: l18 { }; |
| |
| vreg_l19a_2p7: l19 { |
| regulator-min-microvolt = <2696000>; |
| regulator-max-microvolt = <2704000>; |
| }; |
| |
| vreg_l20a_2p95: l20 { |
| regulator-min-microvolt = <2960000>; |
| regulator-max-microvolt = <2960000>; |
| regulator-system-load = <10000>; |
| regulator-allow-set-load; |
| }; |
| |
| vreg_l21a_2p95: l21 { |
| regulator-min-microvolt = <2960000>; |
| regulator-max-microvolt = <2960000>; |
| regulator-system-load = <800000>; |
| regulator-allow-set-load; |
| }; |
| |
| vreg_l22a_2p85: l22 { }; |
| |
| vreg_l23a_3p3: l23 { |
| regulator-min-microvolt = <3312000>; |
| regulator-max-microvolt = <3312000>; |
| }; |
| |
| vreg_l24a_3p075: l24 { |
| regulator-min-microvolt = <3088000>; |
| regulator-max-microvolt = <3088000>; |
| }; |
| |
| vreg_l25a_3p3: l25 { |
| regulator-min-microvolt = <3104000>; |
| regulator-max-microvolt = <3312000>; |
| }; |
| |
| vreg_l26a_1p2: l26 { |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| regulator-allow-set-load; |
| }; |
| |
| vreg_l28_3p0: l28 { |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3000000>; |
| }; |
| |
| vreg_lvs1a_1p8: lvs1 { }; |
| |
| vreg_lvs2a_1p8: lvs2 { }; |
| }; |
| |
| regulators-1 { |
| compatible = "qcom,rpm-pmi8998-regulators"; |
| |
| vdd_bob-supply = <&vph_pwr>; |
| |
| vreg_bob: bob { |
| regulator-min-microvolt = <3312000>; |
| regulator-max-microvolt = <3600000>; |
| }; |
| }; |
| }; |
| |
| &sdhc2 { |
| status = "okay"; |
| cd-gpios = <&tlmm 95 GPIO_ACTIVE_HIGH>; |
| |
| vmmc-supply = <&vreg_l21a_2p95>; |
| vqmmc-supply = <&vreg_l13a_2p95>; |
| |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&sdc2_on &sdc2_cd>; |
| pinctrl-1 = <&sdc2_off &sdc2_cd>; |
| }; |
| |
| &tlmm { |
| gpio-reserved-ranges = <0 4>, <81 4>; |
| |
| mdp_vsync_n: mdp-vsync-n-state { |
| pins = "gpio10"; |
| function = "mdp_vsync_a"; |
| drive-strength = <2>; |
| bias-pull-down; |
| }; |
| |
| nfc_ven: nfc-ven-state { |
| pins = "gpio12"; |
| function = "gpio"; |
| bias-disable; |
| drive-strength = <2>; |
| output-low; |
| }; |
| |
| msm_mclk0_default: msm-mclk0-active-state { |
| pins = "gpio13"; |
| function = "cam_mclk"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| msm_mclk1_default: msm-mclk1-active-state { |
| pins = "gpio14"; |
| function = "cam_mclk"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| cci0_default: cci0-default-state { |
| pins = "gpio18", "gpio19"; |
| function = "cci_i2c"; |
| bias-disable; |
| drive-strength = <2>; |
| }; |
| |
| cci1_default: cci1-default-state { |
| pins = "gpio19", "gpio20"; |
| function = "cci_i2c"; |
| bias-disable; |
| drive-strength = <2>; |
| }; |
| |
| cam0_vdig_default: cam0-vdig-default-state { |
| pins = "gpio21"; |
| function = "gpio"; |
| bias-disable; |
| drive-strength = <2>; |
| }; |
| |
| tof_int: tof-int-state { |
| pins = "gpio22"; |
| function = "gpio"; |
| bias-pull-up; |
| drive-strength = <2>; |
| input-enable; |
| }; |
| |
| cam1_vdig_default: cam1-vdig-default-state { |
| pins = "gpio25"; |
| function = "gpio"; |
| bias-disable; |
| drive-strength = <2>; |
| }; |
| |
| usb_extcon_active: usb-extcon-active-state { |
| pins = "gpio38"; |
| function = "gpio"; |
| bias-disable; |
| drive-strength = <16>; |
| }; |
| |
| tof_reset: tof-reset-state { |
| pins = "gpio27"; |
| function = "gpio"; |
| bias-disable; |
| drive-strength = <2>; |
| }; |
| |
| hall_sensor0_default: acc-cover-open-state { |
| pins = "gpio124"; |
| function = "gpio"; |
| bias-disable; |
| drive-strength = <2>; |
| input-enable; |
| }; |
| |
| ts_int_n: ts-int-n-state { |
| pins = "gpio125"; |
| function = "gpio"; |
| drive-strength = <8>; |
| bias-pull-up; |
| }; |
| |
| usb_vbus_active: usb-vbus-active-state { |
| pins = "gpio128"; |
| function = "gpio"; |
| bias-disable; |
| drive-strength = <2>; |
| output-low; |
| }; |
| |
| ts_vddio_en: ts-vddio-en-default-state { |
| pins = "gpio133"; |
| function = "gpio"; |
| bias-disable; |
| drive-strength = <2>; |
| output-low; |
| }; |
| }; |
| |
| /* |
| * WARNING: |
| * Disable UFS until card quirks are in to avoid unrecoverable hard-brick |
| * that would happen as soon as the UFS card gets probed as, without the |
| * required quirks, the bootloader will be erased right after card probe. |
| */ |
| &ufshc { |
| status = "disabled"; |
| }; |
| |
| &ufsphy { |
| status = "disabled"; |
| }; |
| |
| &usb3 { |
| status = "okay"; |
| }; |
| |
| &usb3_dwc3 { |
| /* Force to peripheral until we have Type-C hooked up */ |
| dr_mode = "peripheral"; |
| extcon = <&extcon_usb>; |
| }; |
| |
| &usb3phy { |
| status = "okay"; |
| |
| vdda-phy-supply = <&vreg_l1a_0p875>; |
| vdda-pll-supply = <&vreg_l2a_1p2>; |
| }; |
