| // SPDX-License-Identifier: BSD-3-Clause |
| /* |
| * Copyright (c) 2021, Linaro Limited |
| */ |
| |
| #include <dt-bindings/input/input.h> |
| #include <dt-bindings/interrupt-controller/irq.h> |
| #include <dt-bindings/spmi/spmi.h> |
| |
| / { |
| thermal-zones { |
| pmm8155au-2-thermal { |
| polling-delay-passive = <100>; |
| polling-delay = <0>; |
| |
| thermal-sensors = <&pmm8155au_2_temp>; |
| |
| trips { |
| trip0 { |
| temperature = <95000>; |
| hysteresis = <0>; |
| type = "passive"; |
| }; |
| |
| trip1 { |
| temperature = <115000>; |
| hysteresis = <0>; |
| type = "hot"; |
| }; |
| |
| trip2 { |
| temperature = <145000>; |
| hysteresis = <0>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| &spmi_bus { |
| pmic@4 { |
| compatible = "qcom,pmm8155au", "qcom,spmi-pmic"; |
| reg = <0x4 SPMI_USID>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pon@800 { |
| compatible = "qcom,pm8916-pon"; |
| reg = <0x0800>; |
| |
| status = "disabled"; |
| }; |
| |
| pmm8155au_2_temp: temp-alarm@2400 { |
| compatible = "qcom,spmi-temp-alarm"; |
| reg = <0x2400>; |
| interrupts = <0x4 0x24 0x0 IRQ_TYPE_EDGE_BOTH>; |
| io-channels = <&pmm8155au_2_adc ADC5_DIE_TEMP>; |
| io-channel-names = "thermal"; |
| #thermal-sensor-cells = <0>; |
| }; |
| |
| pmm8155au_2_adc: adc@3100 { |
| compatible = "qcom,spmi-adc5"; |
| reg = <0x3100>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #io-channel-cells = <1>; |
| interrupts = <0x4 0x31 0x0 IRQ_TYPE_EDGE_RISING>; |
| |
| ref-gnd@0 { |
| reg = <ADC5_REF_GND>; |
| qcom,pre-scaling = <1 1>; |
| label = "ref_gnd"; |
| }; |
| |
| vref-1p25@1 { |
| reg = <ADC5_1P25VREF>; |
| qcom,pre-scaling = <1 1>; |
| label = "vref_1p25"; |
| }; |
| |
| die-temp@6 { |
| reg = <ADC5_DIE_TEMP>; |
| qcom,pre-scaling = <1 1>; |
| label = "die_temp"; |
| }; |
| }; |
| |
| pmm8155au_2_gpios: gpio@c000 { |
| compatible = "qcom,pmm8155au-gpio", "qcom,spmi-gpio"; |
| reg = <0xc000>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| gpio-ranges = <&pmm8155au_2_gpios 0 0 10>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| |
| pmic@5 { |
| compatible = "qcom,pmm8155au", "qcom,spmi-pmic"; |
| reg = <0x5 SPMI_USID>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| }; |