| // SPDX-License-Identifier: GPL-2.0-only OR BSD-3-Clause |
| |
| #include <dt-bindings/spmi/spmi.h> |
| #include <dt-bindings/iio/qcom,spmi-vadc.h> |
| |
| &spmi_bus { |
| pmic@0 { |
| compatible = "qcom,pmp8074", "qcom,spmi-pmic"; |
| reg = <0x0 SPMI_USID>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pmp8074_adc: adc@3100 { |
| compatible = "qcom,spmi-adc-rev2"; |
| reg = <0x3100>; |
| interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #io-channel-cells = <1>; |
| |
| ref-gnd@0 { |
| reg = <ADC5_REF_GND>; |
| qcom,pre-scaling = <1 1>; |
| }; |
| |
| vref-1p25@1 { |
| reg = <ADC5_1P25VREF>; |
| qcom,pre-scaling = <1 1>; |
| }; |
| |
| vref-vadc@2 { |
| reg = <ADC5_VREF_VADC>; |
| qcom,pre-scaling = <1 1>; |
| }; |
| |
| pmic_die: die-temp@6 { |
| reg = <ADC5_DIE_TEMP>; |
| qcom,pre-scaling = <1 1>; |
| }; |
| |
| xo_therm: xo-temp@76 { |
| reg = <ADC5_XO_THERM_100K_PU>; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| qcom,pre-scaling = <1 1>; |
| }; |
| |
| pa_therm1: thermistor1@77 { |
| reg = <ADC5_AMUX_THM1_100K_PU>; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| qcom,pre-scaling = <1 1>; |
| }; |
| |
| pa_therm2: thermistor2@78 { |
| reg = <ADC5_AMUX_THM2_100K_PU>; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| qcom,pre-scaling = <1 1>; |
| }; |
| |
| pa_therm3: thermistor3@79 { |
| reg = <ADC5_AMUX_THM3_100K_PU>; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| qcom,pre-scaling = <1 1>; |
| }; |
| |
| vph-pwr@131 { |
| reg = <ADC5_VPH_PWR>; |
| qcom,pre-scaling = <1 3>; |
| }; |
| }; |
| |
| pmp8074_rtc: rtc@6000 { |
| compatible = "qcom,pm8941-rtc"; |
| reg = <0x6000>, <0x6100>; |
| reg-names = "rtc", "alarm"; |
| interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>; |
| allow-set-time; |
| status = "disabled"; |
| }; |
| |
| pmp8074_gpios: gpio@c000 { |
| compatible = "qcom,pmp8074-gpio", "qcom,spmi-gpio"; |
| reg = <0xc000>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| gpio-ranges = <&pmp8074_gpios 0 0 12>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| |
| pmic@1 { |
| compatible = "qcom,pmp8074", "qcom,spmi-pmic"; |
| reg = <0x1 SPMI_USID>; |
| |
| regulators { |
| compatible = "qcom,pmp8074-regulators"; |
| |
| s3: s3 { |
| regulator-name = "vdd_s3"; |
| regulator-min-microvolt = <592000>; |
| regulator-max-microvolt = <1064000>; |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| s4: s4 { |
| regulator-name = "vdd_s4"; |
| regulator-min-microvolt = <712000>; |
| regulator-max-microvolt = <992000>; |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| l11: l11 { |
| regulator-name = "l11"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| }; |
| }; |
| }; |
