| // SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| /* |
| * sc7280 CRD 3+ board device tree source |
| * |
| * Copyright 2022 Google LLC. |
| */ |
| |
| /dts-v1/; |
| |
| #include "sc7280-herobrine.dtsi" |
| #include "sc7280-herobrine-audio-wcd9385.dtsi" |
| #include "sc7280-herobrine-lte-sku.dtsi" |
| |
| / { |
| model = "Qualcomm Technologies, Inc. sc7280 CRD platform (rev5+)"; |
| compatible = "google,zoglin", "google,hoglin", "qcom,sc7280"; |
| |
| /* FIXED REGULATORS */ |
| |
| /* |
| * On most herobrine boards PPVAR_SYS directly provides VREG_EDP_BL. |
| * However, on CRD there's an extra regulator in the way. Since this |
| * is expected to be uncommon, we'll leave the "vreg_edp_bl" label |
| * in the baseboard herobrine.dtsi point at "ppvar_sys" and then |
| * make a "_crd" specific version here. |
| */ |
| vreg_edp_bl_crd: vreg-edp-bl-crd-regulator { |
| compatible = "regulator-fixed"; |
| regulator-name = "vreg_edp_bl_crd"; |
| |
| gpio = <&pm8350c_gpios 6 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&edp_bl_reg_en>; |
| |
| vin-supply = <&ppvar_sys>; |
| }; |
| }; |
| |
| /* ADDITIONS TO NODES DEFINED IN PARENT DEVICE TREE FILES */ |
| |
| &apps_rsc { |
| pmg1110-regulators { |
| compatible = "qcom,pmg1110-rpmh-regulators"; |
| qcom,pmic-id = "k"; |
| |
| vreg_s1k_1p0: smps1 { |
| regulator-min-microvolt = <1010000>; |
| regulator-max-microvolt = <1170000>; |
| }; |
| }; |
| }; |
| |
| ap_tp_i2c: &i2c0 { |
| status = "okay"; |
| clock-frequency = <400000>; |
| |
| trackpad: trackpad@15 { |
| compatible = "hid-over-i2c"; |
| reg = <0x15>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&tp_int_odl>; |
| |
| interrupt-parent = <&tlmm>; |
| interrupts = <7 IRQ_TYPE_EDGE_FALLING>; |
| |
| post-power-on-delay-ms = <20>; |
| hid-descr-addr = <0x0001>; |
| vdd-supply = <&pp3300_z1>; |
| |
| wakeup-source; |
| }; |
| }; |
| |
| &ap_sar_sensor_i2c { |
| status = "okay"; |
| }; |
| |
| &ap_sar_sensor0 { |
| status = "okay"; |
| }; |
| |
| &ap_sar_sensor1 { |
| status = "okay"; |
| }; |
| |
| ap_ts_pen_1v8: &i2c13 { |
| status = "okay"; |
| clock-frequency = <400000>; |
| |
| ap_ts: touchscreen@5c { |
| compatible = "hid-over-i2c"; |
| reg = <0x5c>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&ts_int_conn>, <&ts_rst_conn>; |
| |
| interrupt-parent = <&tlmm>; |
| interrupts = <55 IRQ_TYPE_LEVEL_LOW>; |
| |
| post-power-on-delay-ms = <500>; |
| hid-descr-addr = <0x0000>; |
| |
| vdd-supply = <&pp3300_left_in_mlb>; |
| }; |
| }; |
| |
| &mdss_edp { |
| status = "okay"; |
| }; |
| |
| &mdss_edp_phy { |
| status = "okay"; |
| }; |
| |
| /* For nvme */ |
| &pcie1 { |
| status = "okay"; |
| }; |
| |
| /* For nvme */ |
| &pcie1_phy { |
| status = "okay"; |
| }; |
| |
| &pm8350c_pwm_backlight { |
| power-supply = <&vreg_edp_bl_crd>; |
| }; |
| |
| /* For eMMC */ |
| &sdhc_1 { |
| status = "okay"; |
| }; |
| |
| /* For SD Card */ |
| &sdhc_2 { |
| status = "okay"; |
| }; |
| |
| /* PINCTRL - ADDITIONS TO NODES IN PARENT DEVICE TREE FILES */ |
| |
| /* |
| * This pin goes to the display panel but then doesn't actually do anything |
| * on the panel itself (it doesn't connect to the touchscreen controller). |
| * We'll set a pullup here just to park the line. |
| */ |
| &ts_rst_conn { |
| bias-pull-up; |
| }; |
| |
| /* PINCTRL - BOARD-SPECIFIC */ |
| |
| /* |
| * Methodology for gpio-line-names: |
| * - If a pin goes to CRD board and is named it gets that name. |
| * - If a pin goes to CRD board and is not named, it gets no name. |
| * - If a pin is totally internal to Qcard then it gets Qcard name. |
| * - If a pin is not hooked up on Qcard, it gets no name. |
| */ |
| |
| &pm8350c_gpios { |
| gpio-line-names = "FLASH_STROBE_1", /* 1 */ |
| "AP_SUSPEND", |
| "PM8008_1_RST_N", |
| "", |
| "", |
| "EDP_BL_REG_EN", |
| "PMIC_EDP_BL_EN", |
| "PMIC_EDP_BL_PWM", |
| ""; |
| |
| edp_bl_reg_en: edp-bl-reg-en-state { |
| pins = "gpio6"; |
| function = "normal"; |
| bias-disable; |
| qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>; |
| }; |
| }; |
| |
| &tlmm { |
| gpio-line-names = "AP_TP_I2C_SDA", /* 0 */ |
| "AP_TP_I2C_SCL", |
| "PCIE1_RESET_N", |
| "PCIE1_WAKE_N", |
| "APPS_I2C_SDA", |
| "APPS_I2C_SCL", |
| "", |
| "TPAD_INT_N", |
| "", |
| "", |
| |
| "GNSS_L1_EN", /* 10 */ |
| "GNSS_L5_EN", |
| "QSPI_DATA_0", |
| "QSPI_DATA_1", |
| "QSPI_CLK", |
| "QSPI_CS_N_1", |
| /* |
| * AP_FLASH_WP is crossystem ABI. Schematics call it |
| * BIOS_FLASH_WP_L (the '_L' suffix is misleading, the |
| * signal is active high). |
| */ |
| "AP_FLASH_WP", |
| "", |
| "AP_EC_INT_N", |
| "", |
| |
| "CAM0_RST_N", /* 20 */ |
| "CAM1_RST_N", |
| "SM_DBG_UART_TX", |
| "SM_DBG_UART_RX", |
| "", |
| "PM8008_IRQ_1", |
| "HOST2WLAN_SOL", |
| "WLAN2HOST_SOL", |
| "MOS_BT_UART_CTS", |
| "MOS_BT_UART_RFR", |
| |
| "MOS_BT_UART_TX", /* 30 */ |
| "MOS_BT_UART_RX", |
| "", |
| "HUB_RST", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| |
| "EC_SPI_MISO_GPIO40", /* 40 */ |
| "EC_SPI_MOSI_GPIO41", |
| "EC_SPI_CLK_GPIO42", |
| "EC_SPI_CS_GPIO43", |
| "", |
| "EARLY_EUD_EN", |
| "", |
| "DP_HOT_PLUG_DETECT", |
| "AP_BRD_ID_0", |
| "AP_BRD_ID_1", |
| |
| "AP_BRD_ID_2", /* 50 */ |
| "NVME_PWR_REG_EN", |
| "TS_I2C_SDA_CONN", |
| "TS_I2C_CLK_CONN", |
| "TS_RST_CONN", |
| "TS_INT_CONN", |
| "AP_I2C_TPM_SDA", |
| "AP_I2C_TPM_SCL", |
| "", |
| "", |
| |
| "EDP_HOT_PLUG_DET_N", /* 60 */ |
| "", |
| "", |
| "AMP_EN", |
| "CAM0_MCLK_GPIO_64", |
| "CAM1_MCLK_GPIO_65", |
| "", |
| "", |
| "", |
| "CCI_I2C_SDA0", |
| |
| "CCI_I2C_SCL0", /* 70 */ |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "PCIE1_CLK_REQ_N", |
| |
| "EN_PP3300_DX_EDP", /* 80 */ |
| "US_EURO_HS_SEL", |
| "FORCED_USB_BOOT", |
| "WCD_RESET_N", |
| "MOS_WLAN_EN", |
| "MOS_BT_EN", |
| "MOS_SW_CTRL", |
| "MOS_PCIE0_RST", |
| "MOS_PCIE0_CLKREQ_N", |
| "MOS_PCIE0_WAKE_N", |
| |
| "MOS_LAA_AS_EN", /* 90 */ |
| "SD_CARD_DET_CONN", |
| "", |
| "", |
| "MOS_BT_WLAN_SLIMBUS_CLK", |
| "MOS_BT_WLAN_SLIMBUS_DAT0", |
| "", |
| "", |
| "", |
| "", |
| |
| "", /* 100 */ |
| "", |
| "", |
| "", |
| "H1_AP_INT_N", |
| "", |
| "AMP_BCLK", |
| "AMP_DIN", |
| "AMP_LRCLK", |
| "UIM1_DATA_GPIO_109", |
| |
| "UIM1_CLK_GPIO_110", /* 110 */ |
| "UIM1_RESET_GPIO_111", |
| "", |
| "UIM1_DATA", |
| "UIM1_CLK", |
| "UIM1_RESET", |
| "UIM1_PRESENT", |
| "SDM_RFFE0_CLK", |
| "SDM_RFFE0_DATA", |
| "", |
| |
| "SDM_RFFE1_DATA", /* 120 */ |
| "SC_GPIO_121", |
| "FASTBOOT_SEL_1", |
| "SC_GPIO_123", |
| "FASTBOOT_SEL_2", |
| "SM_RFFE4_CLK_GRFC_8", |
| "SM_RFFE4_DATA_GRFC_9", |
| "WLAN_COEX_UART1_RX", |
| "WLAN_COEX_UART1_TX", |
| "", |
| |
| "", /* 130 */ |
| "", |
| "", |
| "SDR_QLINK_REQ", |
| "SDR_QLINK_EN", |
| "QLINK0_WMSS_RESET_N", |
| "SMR526_QLINK1_REQ", |
| "SMR526_QLINK1_EN", |
| "SMR526_QLINK1_WMSS_RESET_N", |
| "", |
| |
| "SAR1_INT_N", /* 140 */ |
| "SAR0_INT_N", |
| "", |
| "", |
| "WCD_SWR_TX_CLK", |
| "WCD_SWR_TX_DATA0", |
| "WCD_SWR_TX_DATA1", |
| "WCD_SWR_RX_CLK", |
| "WCD_SWR_RX_DATA0", |
| "WCD_SWR_RX_DATA1", |
| |
| "DMIC01_CLK", /* 150 */ |
| "DMIC01_DATA", |
| "DMIC23_CLK", |
| "DMIC23_DATA", |
| "", |
| "", |
| "EC_IN_RW_N", |
| "EN_PP3300_HUB", |
| "WCD_SWR_TX_DATA2", |
| "", |
| |
| "", /* 160 */ |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| |
| "", /* 170 */ |
| "MOS_BLE_UART_TX", |
| "MOS_BLE_UART_RX", |
| "", |
| ""; |
| }; |
