| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * Microchip Polarfire FPGA programming over slave SPI interface. |
| */ |
| |
| #include <asm/unaligned.h> |
| #include <linux/delay.h> |
| #include <linux/fpga/fpga-mgr.h> |
| #include <linux/iopoll.h> |
| #include <linux/module.h> |
| #include <linux/of.h> |
| #include <linux/spi/spi.h> |
| |
| #define MPF_SPI_ISC_ENABLE 0x0B |
| #define MPF_SPI_ISC_DISABLE 0x0C |
| #define MPF_SPI_READ_STATUS 0x00 |
| #define MPF_SPI_READ_DATA 0x01 |
| #define MPF_SPI_FRAME_INIT 0xAE |
| #define MPF_SPI_FRAME 0xEE |
| #define MPF_SPI_PRG_MODE 0x01 |
| #define MPF_SPI_RELEASE 0x23 |
| |
| #define MPF_SPI_FRAME_SIZE 16 |
| |
| #define MPF_HEADER_SIZE_OFFSET 24 |
| #define MPF_DATA_SIZE_OFFSET 55 |
| |
| #define MPF_LOOKUP_TABLE_RECORD_SIZE 9 |
| #define MPF_LOOKUP_TABLE_BLOCK_ID_OFFSET 0 |
| #define MPF_LOOKUP_TABLE_BLOCK_START_OFFSET 1 |
| |
| #define MPF_COMPONENTS_SIZE_ID 5 |
| #define MPF_BITSTREAM_ID 8 |
| |
| #define MPF_BITS_PER_COMPONENT_SIZE 22 |
| |
| #define MPF_STATUS_POLL_TIMEOUT (2 * USEC_PER_SEC) |
| #define MPF_STATUS_BUSY BIT(0) |
| #define MPF_STATUS_READY BIT(1) |
| #define MPF_STATUS_SPI_VIOLATION BIT(2) |
| #define MPF_STATUS_SPI_ERROR BIT(3) |
| |
| struct mpf_priv { |
| struct spi_device *spi; |
| bool program_mode; |
| u8 tx __aligned(ARCH_KMALLOC_MINALIGN); |
| u8 rx; |
| }; |
| |
| static int mpf_read_status(struct mpf_priv *priv) |
| { |
| /* |
| * HW status is returned on MISO in the first byte after CS went |
| * active. However, first reading can be inadequate, so we submit |
| * two identical SPI transfers and use result of the later one. |
| */ |
| struct spi_transfer xfers[2] = { |
| { |
| .tx_buf = &priv->tx, |
| .rx_buf = &priv->rx, |
| .len = 1, |
| .cs_change = 1, |
| }, { |
| .tx_buf = &priv->tx, |
| .rx_buf = &priv->rx, |
| .len = 1, |
| }, |
| }; |
| u8 status; |
| int ret; |
| |
| priv->tx = MPF_SPI_READ_STATUS; |
| |
| ret = spi_sync_transfer(priv->spi, xfers, 2); |
| if (ret) |
| return ret; |
| |
| status = priv->rx; |
| |
| if ((status & MPF_STATUS_SPI_VIOLATION) || |
| (status & MPF_STATUS_SPI_ERROR)) |
| return -EIO; |
| |
| return status; |
| } |
| |
| static enum fpga_mgr_states mpf_ops_state(struct fpga_manager *mgr) |
| { |
| struct mpf_priv *priv = mgr->priv; |
| bool program_mode; |
| int status; |
| |
| program_mode = priv->program_mode; |
| status = mpf_read_status(priv); |
| |
| if (!program_mode && !status) |
| return FPGA_MGR_STATE_OPERATING; |
| |
| return FPGA_MGR_STATE_UNKNOWN; |
| } |
| |
| static int mpf_ops_parse_header(struct fpga_manager *mgr, |
| struct fpga_image_info *info, |
| const char *buf, size_t count) |
| { |
| size_t component_size_byte_num, component_size_byte_off, |
| components_size_start, bitstream_start, |
| block_id_offset, block_start_offset; |
| u8 header_size, blocks_num, block_id; |
| u32 block_start, component_size; |
| u16 components_num, i; |
| |
| if (!buf) { |
| dev_err(&mgr->dev, "Image buffer is not provided\n"); |
| return -EINVAL; |
| } |
| |
| header_size = *(buf + MPF_HEADER_SIZE_OFFSET); |
| if (header_size > count) { |
| info->header_size = header_size; |
| return -EAGAIN; |
| } |
| |
| /* |
| * Go through look-up table to find out where actual bitstream starts |
| * and where sizes of components of the bitstream lies. |
| */ |
| blocks_num = *(buf + header_size - 1); |
| block_id_offset = header_size + MPF_LOOKUP_TABLE_BLOCK_ID_OFFSET; |
| block_start_offset = header_size + MPF_LOOKUP_TABLE_BLOCK_START_OFFSET; |
| |
| header_size += blocks_num * MPF_LOOKUP_TABLE_RECORD_SIZE; |
| if (header_size > count) { |
| info->header_size = header_size; |
| return -EAGAIN; |
| } |
| |
| components_size_start = 0; |
| bitstream_start = 0; |
| |
| while (blocks_num--) { |
| block_id = *(buf + block_id_offset); |
| block_start = get_unaligned_le32(buf + block_start_offset); |
| |
| switch (block_id) { |
| case MPF_BITSTREAM_ID: |
| bitstream_start = block_start; |
| info->header_size = block_start; |
| if (block_start > count) |
| return -EAGAIN; |
| |
| break; |
| case MPF_COMPONENTS_SIZE_ID: |
| components_size_start = block_start; |
| break; |
| default: |
| break; |
| } |
| |
| if (bitstream_start && components_size_start) |
| break; |
| |
| block_id_offset += MPF_LOOKUP_TABLE_RECORD_SIZE; |
| block_start_offset += MPF_LOOKUP_TABLE_RECORD_SIZE; |
| } |
| |
| if (!bitstream_start || !components_size_start) { |
| dev_err(&mgr->dev, "Failed to parse header look-up table\n"); |
| return -EFAULT; |
| } |
| |
| /* |
| * Parse bitstream size. |
| * Sizes of components of the bitstream are 22-bits long placed next |
| * to each other. Image header should be extended by now up to where |
| * actual bitstream starts, so no need for overflow check anymore. |
| */ |
| components_num = get_unaligned_le16(buf + MPF_DATA_SIZE_OFFSET); |
| |
| for (i = 0; i < components_num; i++) { |
| component_size_byte_num = |
| (i * MPF_BITS_PER_COMPONENT_SIZE) / BITS_PER_BYTE; |
| component_size_byte_off = |
| (i * MPF_BITS_PER_COMPONENT_SIZE) % BITS_PER_BYTE; |
| |
| component_size = get_unaligned_le32(buf + |
| components_size_start + |
| component_size_byte_num); |
| component_size >>= component_size_byte_off; |
| component_size &= GENMASK(MPF_BITS_PER_COMPONENT_SIZE - 1, 0); |
| |
| info->data_size += component_size * MPF_SPI_FRAME_SIZE; |
| } |
| |
| return 0; |
| } |
| |
| static int mpf_poll_status(struct mpf_priv *priv, u8 mask) |
| { |
| int ret, status; |
| |
| /* |
| * Busy poll HW status. Polling stops if any of the following |
| * conditions are met: |
| * - timeout is reached |
| * - mpf_read_status() returns an error |
| * - busy bit is cleared AND mask bits are set |
| */ |
| ret = read_poll_timeout(mpf_read_status, status, |
| (status < 0) || |
| ((status & (MPF_STATUS_BUSY | mask)) == mask), |
| 0, MPF_STATUS_POLL_TIMEOUT, false, priv); |
| if (ret < 0) |
| return ret; |
| |
| return status; |
| } |
| |
| static int mpf_spi_write(struct mpf_priv *priv, const void *buf, size_t buf_size) |
| { |
| int status = mpf_poll_status(priv, 0); |
| |
| if (status < 0) |
| return status; |
| |
| return spi_write_then_read(priv->spi, buf, buf_size, NULL, 0); |
| } |
| |
| static int mpf_spi_write_then_read(struct mpf_priv *priv, |
| const void *txbuf, size_t txbuf_size, |
| void *rxbuf, size_t rxbuf_size) |
| { |
| const u8 read_command[] = { MPF_SPI_READ_DATA }; |
| int ret; |
| |
| ret = mpf_spi_write(priv, txbuf, txbuf_size); |
| if (ret) |
| return ret; |
| |
| ret = mpf_poll_status(priv, MPF_STATUS_READY); |
| if (ret < 0) |
| return ret; |
| |
| return spi_write_then_read(priv->spi, read_command, sizeof(read_command), |
| rxbuf, rxbuf_size); |
| } |
| |
| static int mpf_ops_write_init(struct fpga_manager *mgr, |
| struct fpga_image_info *info, const char *buf, |
| size_t count) |
| { |
| const u8 program_mode[] = { MPF_SPI_FRAME_INIT, MPF_SPI_PRG_MODE }; |
| const u8 isc_en_command[] = { MPF_SPI_ISC_ENABLE }; |
| struct mpf_priv *priv = mgr->priv; |
| struct device *dev = &mgr->dev; |
| u32 isc_ret = 0; |
| int ret; |
| |
| if (info->flags & FPGA_MGR_PARTIAL_RECONFIG) { |
| dev_err(dev, "Partial reconfiguration is not supported\n"); |
| return -EOPNOTSUPP; |
| } |
| |
| ret = mpf_spi_write_then_read(priv, isc_en_command, sizeof(isc_en_command), |
| &isc_ret, sizeof(isc_ret)); |
| if (ret || isc_ret) { |
| dev_err(dev, "Failed to enable ISC: spi_ret %d, isc_ret %u\n", |
| ret, isc_ret); |
| return -EFAULT; |
| } |
| |
| ret = mpf_spi_write(priv, program_mode, sizeof(program_mode)); |
| if (ret) { |
| dev_err(dev, "Failed to enter program mode: %d\n", ret); |
| return ret; |
| } |
| |
| priv->program_mode = true; |
| |
| return 0; |
| } |
| |
| static int mpf_spi_frame_write(struct mpf_priv *priv, const char *buf) |
| { |
| struct spi_transfer xfers[2] = { |
| { |
| .tx_buf = &priv->tx, |
| .len = 1, |
| }, { |
| .tx_buf = buf, |
| .len = MPF_SPI_FRAME_SIZE, |
| }, |
| }; |
| int ret; |
| |
| ret = mpf_poll_status(priv, 0); |
| if (ret < 0) |
| return ret; |
| |
| priv->tx = MPF_SPI_FRAME; |
| |
| return spi_sync_transfer(priv->spi, xfers, ARRAY_SIZE(xfers)); |
| } |
| |
| static int mpf_ops_write(struct fpga_manager *mgr, const char *buf, size_t count) |
| { |
| struct mpf_priv *priv = mgr->priv; |
| struct device *dev = &mgr->dev; |
| int ret, i; |
| |
| if (count % MPF_SPI_FRAME_SIZE) { |
| dev_err(dev, "Bitstream size is not a multiple of %d\n", |
| MPF_SPI_FRAME_SIZE); |
| return -EINVAL; |
| } |
| |
| for (i = 0; i < count / MPF_SPI_FRAME_SIZE; i++) { |
| ret = mpf_spi_frame_write(priv, buf + i * MPF_SPI_FRAME_SIZE); |
| if (ret) { |
| dev_err(dev, "Failed to write bitstream frame %d/%zu\n", |
| i, count / MPF_SPI_FRAME_SIZE); |
| return ret; |
| } |
| } |
| |
| return 0; |
| } |
| |
| static int mpf_ops_write_complete(struct fpga_manager *mgr, |
| struct fpga_image_info *info) |
| { |
| const u8 isc_dis_command[] = { MPF_SPI_ISC_DISABLE }; |
| const u8 release_command[] = { MPF_SPI_RELEASE }; |
| struct mpf_priv *priv = mgr->priv; |
| struct device *dev = &mgr->dev; |
| int ret; |
| |
| ret = mpf_spi_write(priv, isc_dis_command, sizeof(isc_dis_command)); |
| if (ret) { |
| dev_err(dev, "Failed to disable ISC: %d\n", ret); |
| return ret; |
| } |
| |
| usleep_range(1000, 2000); |
| |
| ret = mpf_spi_write(priv, release_command, sizeof(release_command)); |
| if (ret) { |
| dev_err(dev, "Failed to exit program mode: %d\n", ret); |
| return ret; |
| } |
| |
| priv->program_mode = false; |
| |
| return 0; |
| } |
| |
| static const struct fpga_manager_ops mpf_ops = { |
| .state = mpf_ops_state, |
| .initial_header_size = 71, |
| .skip_header = true, |
| .parse_header = mpf_ops_parse_header, |
| .write_init = mpf_ops_write_init, |
| .write = mpf_ops_write, |
| .write_complete = mpf_ops_write_complete, |
| }; |
| |
| static int mpf_probe(struct spi_device *spi) |
| { |
| struct device *dev = &spi->dev; |
| struct fpga_manager *mgr; |
| struct mpf_priv *priv; |
| |
| priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); |
| if (!priv) |
| return -ENOMEM; |
| |
| priv->spi = spi; |
| |
| mgr = devm_fpga_mgr_register(dev, "Microchip Polarfire SPI FPGA Manager", |
| &mpf_ops, priv); |
| |
| return PTR_ERR_OR_ZERO(mgr); |
| } |
| |
| static const struct spi_device_id mpf_spi_ids[] = { |
| { .name = "mpf-spi-fpga-mgr", }, |
| {}, |
| }; |
| MODULE_DEVICE_TABLE(spi, mpf_spi_ids); |
| |
| #if IS_ENABLED(CONFIG_OF) |
| static const struct of_device_id mpf_of_ids[] = { |
| { .compatible = "microchip,mpf-spi-fpga-mgr" }, |
| {}, |
| }; |
| MODULE_DEVICE_TABLE(of, mpf_of_ids); |
| #endif /* IS_ENABLED(CONFIG_OF) */ |
| |
| static struct spi_driver mpf_driver = { |
| .probe = mpf_probe, |
| .id_table = mpf_spi_ids, |
| .driver = { |
| .name = "microchip_mpf_spi_fpga_mgr", |
| .of_match_table = of_match_ptr(mpf_of_ids), |
| }, |
| }; |
| |
| module_spi_driver(mpf_driver); |
| |
| MODULE_DESCRIPTION("Microchip Polarfire SPI FPGA Manager"); |
| MODULE_AUTHOR("Ivan Bornyakov <i.bornyakov@metrotek.ru>"); |
| MODULE_LICENSE("GPL"); |