| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * Driver for the Texas Instruments DS90UB953 video serializer |
| * |
| * Based on a driver from Luca Ceresoli <luca@lucaceresoli.net> |
| * |
| * Copyright (c) 2019 Luca Ceresoli <luca@lucaceresoli.net> |
| * Copyright (c) 2023 Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> |
| */ |
| |
| #include <linux/clk-provider.h> |
| #include <linux/clk.h> |
| #include <linux/delay.h> |
| #include <linux/fwnode.h> |
| #include <linux/gpio/driver.h> |
| #include <linux/i2c-atr.h> |
| #include <linux/i2c.h> |
| #include <linux/kernel.h> |
| #include <linux/math64.h> |
| #include <linux/module.h> |
| #include <linux/property.h> |
| #include <linux/rational.h> |
| #include <linux/regmap.h> |
| |
| #include <media/i2c/ds90ub9xx.h> |
| #include <media/v4l2-ctrls.h> |
| #include <media/v4l2-event.h> |
| #include <media/v4l2-fwnode.h> |
| #include <media/v4l2-mediabus.h> |
| #include <media/v4l2-subdev.h> |
| |
| #define UB953_PAD_SINK 0 |
| #define UB953_PAD_SOURCE 1 |
| |
| #define UB953_NUM_GPIOS 4 |
| |
| #define UB953_DEFAULT_CLKOUT_RATE 25000000UL |
| |
| #define UB953_REG_RESET_CTL 0x01 |
| #define UB953_REG_RESET_CTL_DIGITAL_RESET_1 BIT(1) |
| #define UB953_REG_RESET_CTL_DIGITAL_RESET_0 BIT(0) |
| |
| #define UB953_REG_GENERAL_CFG 0x02 |
| #define UB953_REG_GENERAL_CFG_CONT_CLK BIT(6) |
| #define UB953_REG_GENERAL_CFG_CSI_LANE_SEL_SHIFT 4 |
| #define UB953_REG_GENERAL_CFG_CSI_LANE_SEL_MASK GENMASK(5, 4) |
| #define UB953_REG_GENERAL_CFG_CRC_TX_GEN_ENABLE BIT(1) |
| #define UB953_REG_GENERAL_CFG_I2C_STRAP_MODE BIT(0) |
| |
| #define UB953_REG_MODE_SEL 0x03 |
| #define UB953_REG_MODE_SEL_MODE_DONE BIT(3) |
| #define UB953_REG_MODE_SEL_MODE_OVERRIDE BIT(4) |
| #define UB953_REG_MODE_SEL_MODE_MASK GENMASK(2, 0) |
| |
| #define UB953_REG_CLKOUT_CTRL0 0x06 |
| #define UB953_REG_CLKOUT_CTRL1 0x07 |
| |
| #define UB953_REG_SCL_HIGH_TIME 0x0b |
| #define UB953_REG_SCL_LOW_TIME 0x0c |
| |
| #define UB953_REG_LOCAL_GPIO_DATA 0x0d |
| #define UB953_REG_LOCAL_GPIO_DATA_GPIO_RMTEN(n) BIT(4 + (n)) |
| #define UB953_REG_LOCAL_GPIO_DATA_GPIO_OUT_SRC(n) BIT(0 + (n)) |
| |
| #define UB953_REG_GPIO_INPUT_CTRL 0x0e |
| #define UB953_REG_GPIO_INPUT_CTRL_OUT_EN(n) BIT(4 + (n)) |
| #define UB953_REG_GPIO_INPUT_CTRL_INPUT_EN(n) BIT(0 + (n)) |
| |
| #define UB953_REG_REV_MASK_ID 0x50 |
| #define UB953_REG_GENERAL_STATUS 0x52 |
| |
| #define UB953_REG_GPIO_PIN_STS 0x53 |
| #define UB953_REG_GPIO_PIN_STS_GPIO_STS(n) BIT(0 + (n)) |
| |
| #define UB953_REG_BIST_ERR_CNT 0x54 |
| #define UB953_REG_CRC_ERR_CNT1 0x55 |
| #define UB953_REG_CRC_ERR_CNT2 0x56 |
| |
| #define UB953_REG_CSI_ERR_CNT 0x5c |
| #define UB953_REG_CSI_ERR_STATUS 0x5d |
| #define UB953_REG_CSI_ERR_DLANE01 0x5e |
| #define UB953_REG_CSI_ERR_DLANE23 0x5f |
| #define UB953_REG_CSI_ERR_CLK_LANE 0x60 |
| #define UB953_REG_CSI_PKT_HDR_VC_ID 0x61 |
| #define UB953_REG_PKT_HDR_WC_LSB 0x62 |
| #define UB953_REG_PKT_HDR_WC_MSB 0x63 |
| #define UB953_REG_CSI_ECC 0x64 |
| |
| #define UB953_REG_IND_ACC_CTL 0xb0 |
| #define UB953_REG_IND_ACC_ADDR 0xb1 |
| #define UB953_REG_IND_ACC_DATA 0xb2 |
| |
| #define UB953_REG_FPD3_RX_ID(n) (0xf0 + (n)) |
| #define UB953_REG_FPD3_RX_ID_LEN 6 |
| |
| /* Indirect register blocks */ |
| #define UB953_IND_TARGET_PAT_GEN 0x00 |
| #define UB953_IND_TARGET_FPD3_TX 0x01 |
| #define UB953_IND_TARGET_DIE_ID 0x02 |
| |
| #define UB953_IND_PGEN_CTL 0x01 |
| #define UB953_IND_PGEN_CTL_PGEN_ENABLE BIT(0) |
| #define UB953_IND_PGEN_CFG 0x02 |
| #define UB953_IND_PGEN_CSI_DI 0x03 |
| #define UB953_IND_PGEN_LINE_SIZE1 0x04 |
| #define UB953_IND_PGEN_LINE_SIZE0 0x05 |
| #define UB953_IND_PGEN_BAR_SIZE1 0x06 |
| #define UB953_IND_PGEN_BAR_SIZE0 0x07 |
| #define UB953_IND_PGEN_ACT_LPF1 0x08 |
| #define UB953_IND_PGEN_ACT_LPF0 0x09 |
| #define UB953_IND_PGEN_TOT_LPF1 0x0a |
| #define UB953_IND_PGEN_TOT_LPF0 0x0b |
| #define UB953_IND_PGEN_LINE_PD1 0x0c |
| #define UB953_IND_PGEN_LINE_PD0 0x0d |
| #define UB953_IND_PGEN_VBP 0x0e |
| #define UB953_IND_PGEN_VFP 0x0f |
| #define UB953_IND_PGEN_COLOR(n) (0x10 + (n)) /* n <= 15 */ |
| |
| /* Note: Only sync mode supported for now */ |
| enum ub953_mode { |
| /* FPD-Link III CSI-2 synchronous mode */ |
| UB953_MODE_SYNC, |
| /* FPD-Link III CSI-2 non-synchronous mode, external ref clock */ |
| UB953_MODE_NONSYNC_EXT, |
| /* FPD-Link III CSI-2 non-synchronous mode, internal ref clock */ |
| UB953_MODE_NONSYNC_INT, |
| /* FPD-Link III DVP mode */ |
| UB953_MODE_DVP, |
| }; |
| |
| struct ub953_hw_data { |
| const char *model; |
| bool is_ub971; |
| }; |
| |
| struct ub953_clkout_data { |
| u32 hs_div; |
| u32 m; |
| u32 n; |
| unsigned long rate; |
| }; |
| |
| struct ub953_data { |
| const struct ub953_hw_data *hw_data; |
| |
| struct i2c_client *client; |
| struct regmap *regmap; |
| struct clk *clkin; |
| |
| u32 num_data_lanes; |
| bool non_continous_clk; |
| |
| struct gpio_chip gpio_chip; |
| |
| struct v4l2_subdev sd; |
| struct media_pad pads[2]; |
| |
| struct v4l2_async_notifier notifier; |
| |
| struct v4l2_subdev *source_sd; |
| u16 source_sd_pad; |
| |
| u64 enabled_source_streams; |
| |
| /* lock for register access */ |
| struct mutex reg_lock; |
| |
| u8 current_indirect_target; |
| |
| struct clk_hw clkout_clk_hw; |
| |
| enum ub953_mode mode; |
| |
| const struct ds90ub9xx_platform_data *plat_data; |
| }; |
| |
| static inline struct ub953_data *sd_to_ub953(struct v4l2_subdev *sd) |
| { |
| return container_of(sd, struct ub953_data, sd); |
| } |
| |
| /* |
| * HW Access |
| */ |
| |
| static int ub953_read(struct ub953_data *priv, u8 reg, u8 *val) |
| { |
| unsigned int v; |
| int ret; |
| |
| mutex_lock(&priv->reg_lock); |
| |
| ret = regmap_read(priv->regmap, reg, &v); |
| if (ret) { |
| dev_err(&priv->client->dev, "Cannot read register 0x%02x: %d\n", |
| reg, ret); |
| goto out_unlock; |
| } |
| |
| *val = v; |
| |
| out_unlock: |
| mutex_unlock(&priv->reg_lock); |
| |
| return ret; |
| } |
| |
| static int ub953_write(struct ub953_data *priv, u8 reg, u8 val) |
| { |
| int ret; |
| |
| mutex_lock(&priv->reg_lock); |
| |
| ret = regmap_write(priv->regmap, reg, val); |
| if (ret) |
| dev_err(&priv->client->dev, |
| "Cannot write register 0x%02x: %d\n", reg, ret); |
| |
| mutex_unlock(&priv->reg_lock); |
| |
| return ret; |
| } |
| |
| static int ub953_select_ind_reg_block(struct ub953_data *priv, u8 block) |
| { |
| struct device *dev = &priv->client->dev; |
| int ret; |
| |
| if (priv->current_indirect_target == block) |
| return 0; |
| |
| ret = regmap_write(priv->regmap, UB953_REG_IND_ACC_CTL, block << 2); |
| if (ret) { |
| dev_err(dev, "%s: cannot select indirect target %u (%d)\n", |
| __func__, block, ret); |
| return ret; |
| } |
| |
| priv->current_indirect_target = block; |
| |
| return 0; |
| } |
| |
| __maybe_unused |
| static int ub953_read_ind(struct ub953_data *priv, u8 block, u8 reg, u8 *val) |
| { |
| unsigned int v; |
| int ret; |
| |
| mutex_lock(&priv->reg_lock); |
| |
| ret = ub953_select_ind_reg_block(priv, block); |
| if (ret) |
| goto out_unlock; |
| |
| ret = regmap_write(priv->regmap, UB953_REG_IND_ACC_ADDR, reg); |
| if (ret) { |
| dev_err(&priv->client->dev, |
| "Write to IND_ACC_ADDR failed when reading %u:%x02x: %d\n", |
| block, reg, ret); |
| goto out_unlock; |
| } |
| |
| ret = regmap_read(priv->regmap, UB953_REG_IND_ACC_DATA, &v); |
| if (ret) { |
| dev_err(&priv->client->dev, |
| "Write to IND_ACC_DATA failed when reading %u:%x02x: %d\n", |
| block, reg, ret); |
| goto out_unlock; |
| } |
| |
| *val = v; |
| |
| out_unlock: |
| mutex_unlock(&priv->reg_lock); |
| |
| return ret; |
| } |
| |
| __maybe_unused |
| static int ub953_write_ind(struct ub953_data *priv, u8 block, u8 reg, u8 val) |
| { |
| int ret; |
| |
| mutex_lock(&priv->reg_lock); |
| |
| ret = ub953_select_ind_reg_block(priv, block); |
| if (ret) |
| goto out_unlock; |
| |
| ret = regmap_write(priv->regmap, UB953_REG_IND_ACC_ADDR, reg); |
| if (ret) { |
| dev_err(&priv->client->dev, |
| "Write to IND_ACC_ADDR failed when writing %u:%x02x: %d\n", |
| block, reg, ret); |
| goto out_unlock; |
| } |
| |
| ret = regmap_write(priv->regmap, UB953_REG_IND_ACC_DATA, val); |
| if (ret) { |
| dev_err(&priv->client->dev, |
| "Write to IND_ACC_DATA failed when writing %u:%x02x\n: %d\n", |
| block, reg, ret); |
| } |
| |
| out_unlock: |
| mutex_unlock(&priv->reg_lock); |
| |
| return ret; |
| } |
| |
| /* |
| * GPIO chip |
| */ |
| static int ub953_gpio_get_direction(struct gpio_chip *gc, unsigned int offset) |
| { |
| struct ub953_data *priv = gpiochip_get_data(gc); |
| int ret; |
| u8 v; |
| |
| ret = ub953_read(priv, UB953_REG_GPIO_INPUT_CTRL, &v); |
| if (ret) |
| return ret; |
| |
| if (v & UB953_REG_GPIO_INPUT_CTRL_INPUT_EN(offset)) |
| return GPIO_LINE_DIRECTION_IN; |
| else |
| return GPIO_LINE_DIRECTION_OUT; |
| } |
| |
| static int ub953_gpio_direction_in(struct gpio_chip *gc, unsigned int offset) |
| { |
| struct ub953_data *priv = gpiochip_get_data(gc); |
| |
| return regmap_update_bits(priv->regmap, UB953_REG_GPIO_INPUT_CTRL, |
| UB953_REG_GPIO_INPUT_CTRL_INPUT_EN(offset) | |
| UB953_REG_GPIO_INPUT_CTRL_OUT_EN(offset), |
| UB953_REG_GPIO_INPUT_CTRL_INPUT_EN(offset)); |
| } |
| |
| static int ub953_gpio_direction_out(struct gpio_chip *gc, unsigned int offset, |
| int value) |
| { |
| struct ub953_data *priv = gpiochip_get_data(gc); |
| int ret; |
| |
| ret = regmap_update_bits(priv->regmap, UB953_REG_LOCAL_GPIO_DATA, |
| UB953_REG_LOCAL_GPIO_DATA_GPIO_OUT_SRC(offset), |
| value ? UB953_REG_LOCAL_GPIO_DATA_GPIO_OUT_SRC(offset) : |
| 0); |
| |
| if (ret) |
| return ret; |
| |
| return regmap_update_bits(priv->regmap, UB953_REG_GPIO_INPUT_CTRL, |
| UB953_REG_GPIO_INPUT_CTRL_INPUT_EN(offset) | |
| UB953_REG_GPIO_INPUT_CTRL_OUT_EN(offset), |
| UB953_REG_GPIO_INPUT_CTRL_OUT_EN(offset)); |
| } |
| |
| static int ub953_gpio_get(struct gpio_chip *gc, unsigned int offset) |
| { |
| struct ub953_data *priv = gpiochip_get_data(gc); |
| int ret; |
| u8 v; |
| |
| ret = ub953_read(priv, UB953_REG_GPIO_PIN_STS, &v); |
| if (ret) |
| return ret; |
| |
| return !!(v & UB953_REG_GPIO_PIN_STS_GPIO_STS(offset)); |
| } |
| |
| static void ub953_gpio_set(struct gpio_chip *gc, unsigned int offset, int value) |
| { |
| struct ub953_data *priv = gpiochip_get_data(gc); |
| |
| regmap_update_bits(priv->regmap, UB953_REG_LOCAL_GPIO_DATA, |
| UB953_REG_LOCAL_GPIO_DATA_GPIO_OUT_SRC(offset), |
| value ? UB953_REG_LOCAL_GPIO_DATA_GPIO_OUT_SRC(offset) : |
| 0); |
| } |
| |
| static int ub953_gpio_of_xlate(struct gpio_chip *gc, |
| const struct of_phandle_args *gpiospec, |
| u32 *flags) |
| { |
| if (flags) |
| *flags = gpiospec->args[1]; |
| |
| return gpiospec->args[0]; |
| } |
| |
| static int ub953_gpiochip_probe(struct ub953_data *priv) |
| { |
| struct device *dev = &priv->client->dev; |
| struct gpio_chip *gc = &priv->gpio_chip; |
| int ret; |
| |
| /* Set all GPIOs to local input mode */ |
| ub953_write(priv, UB953_REG_LOCAL_GPIO_DATA, 0); |
| ub953_write(priv, UB953_REG_GPIO_INPUT_CTRL, 0xf); |
| |
| gc->label = dev_name(dev); |
| gc->parent = dev; |
| gc->owner = THIS_MODULE; |
| gc->base = -1; |
| gc->can_sleep = true; |
| gc->ngpio = UB953_NUM_GPIOS; |
| gc->get_direction = ub953_gpio_get_direction; |
| gc->direction_input = ub953_gpio_direction_in; |
| gc->direction_output = ub953_gpio_direction_out; |
| gc->get = ub953_gpio_get; |
| gc->set = ub953_gpio_set; |
| gc->of_xlate = ub953_gpio_of_xlate; |
| gc->of_gpio_n_cells = 2; |
| |
| ret = gpiochip_add_data(gc, priv); |
| if (ret) { |
| dev_err(dev, "Failed to add GPIOs: %d\n", ret); |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static void ub953_gpiochip_remove(struct ub953_data *priv) |
| { |
| gpiochip_remove(&priv->gpio_chip); |
| } |
| |
| /* |
| * V4L2 |
| */ |
| |
| static int _ub953_set_routing(struct v4l2_subdev *sd, |
| struct v4l2_subdev_state *state, |
| struct v4l2_subdev_krouting *routing) |
| { |
| static const struct v4l2_mbus_framefmt format = { |
| .width = 640, |
| .height = 480, |
| .code = MEDIA_BUS_FMT_UYVY8_1X16, |
| .field = V4L2_FIELD_NONE, |
| .colorspace = V4L2_COLORSPACE_SRGB, |
| .ycbcr_enc = V4L2_YCBCR_ENC_601, |
| .quantization = V4L2_QUANTIZATION_LIM_RANGE, |
| .xfer_func = V4L2_XFER_FUNC_SRGB, |
| }; |
| int ret; |
| |
| /* |
| * Note: we can only support up to V4L2_FRAME_DESC_ENTRY_MAX, until |
| * frame desc is made dynamically allocated. |
| */ |
| |
| if (routing->num_routes > V4L2_FRAME_DESC_ENTRY_MAX) |
| return -EINVAL; |
| |
| ret = v4l2_subdev_routing_validate(sd, routing, |
| V4L2_SUBDEV_ROUTING_ONLY_1_TO_1); |
| if (ret) |
| return ret; |
| |
| ret = v4l2_subdev_set_routing_with_fmt(sd, state, routing, &format); |
| if (ret) |
| return ret; |
| |
| return 0; |
| } |
| |
| static int ub953_set_routing(struct v4l2_subdev *sd, |
| struct v4l2_subdev_state *state, |
| enum v4l2_subdev_format_whence which, |
| struct v4l2_subdev_krouting *routing) |
| { |
| struct ub953_data *priv = sd_to_ub953(sd); |
| |
| if (which == V4L2_SUBDEV_FORMAT_ACTIVE && priv->enabled_source_streams) |
| return -EBUSY; |
| |
| return _ub953_set_routing(sd, state, routing); |
| } |
| |
| static int ub953_get_frame_desc(struct v4l2_subdev *sd, unsigned int pad, |
| struct v4l2_mbus_frame_desc *fd) |
| { |
| struct ub953_data *priv = sd_to_ub953(sd); |
| struct v4l2_mbus_frame_desc source_fd; |
| struct v4l2_subdev_route *route; |
| struct v4l2_subdev_state *state; |
| int ret; |
| |
| if (pad != UB953_PAD_SOURCE) |
| return -EINVAL; |
| |
| ret = v4l2_subdev_call(priv->source_sd, pad, get_frame_desc, |
| priv->source_sd_pad, &source_fd); |
| if (ret) |
| return ret; |
| |
| fd->type = V4L2_MBUS_FRAME_DESC_TYPE_CSI2; |
| |
| state = v4l2_subdev_lock_and_get_active_state(sd); |
| |
| for_each_active_route(&state->routing, route) { |
| struct v4l2_mbus_frame_desc_entry *source_entry = NULL; |
| unsigned int i; |
| |
| if (route->source_pad != pad) |
| continue; |
| |
| for (i = 0; i < source_fd.num_entries; i++) { |
| if (source_fd.entry[i].stream == route->sink_stream) { |
| source_entry = &source_fd.entry[i]; |
| break; |
| } |
| } |
| |
| if (!source_entry) { |
| dev_err(&priv->client->dev, |
| "Failed to find stream from source frame desc\n"); |
| ret = -EPIPE; |
| goto out_unlock; |
| } |
| |
| fd->entry[fd->num_entries].stream = route->source_stream; |
| fd->entry[fd->num_entries].flags = source_entry->flags; |
| fd->entry[fd->num_entries].length = source_entry->length; |
| fd->entry[fd->num_entries].pixelcode = source_entry->pixelcode; |
| fd->entry[fd->num_entries].bus.csi2.vc = |
| source_entry->bus.csi2.vc; |
| fd->entry[fd->num_entries].bus.csi2.dt = |
| source_entry->bus.csi2.dt; |
| |
| fd->num_entries++; |
| } |
| |
| out_unlock: |
| v4l2_subdev_unlock_state(state); |
| |
| return ret; |
| } |
| |
| static int ub953_set_fmt(struct v4l2_subdev *sd, |
| struct v4l2_subdev_state *state, |
| struct v4l2_subdev_format *format) |
| { |
| struct ub953_data *priv = sd_to_ub953(sd); |
| struct v4l2_mbus_framefmt *fmt; |
| |
| if (format->which == V4L2_SUBDEV_FORMAT_ACTIVE && |
| priv->enabled_source_streams) |
| return -EBUSY; |
| |
| /* No transcoding, source and sink formats must match. */ |
| if (format->pad == UB953_PAD_SOURCE) |
| return v4l2_subdev_get_fmt(sd, state, format); |
| |
| /* Set sink format */ |
| fmt = v4l2_subdev_state_get_format(state, format->pad, format->stream); |
| if (!fmt) |
| return -EINVAL; |
| |
| *fmt = format->format; |
| |
| /* Propagate to source format */ |
| fmt = v4l2_subdev_state_get_opposite_stream_format(state, format->pad, |
| format->stream); |
| if (!fmt) |
| return -EINVAL; |
| |
| *fmt = format->format; |
| |
| return 0; |
| } |
| |
| static int ub953_init_state(struct v4l2_subdev *sd, |
| struct v4l2_subdev_state *state) |
| { |
| struct v4l2_subdev_route routes[] = { |
| { |
| .sink_pad = UB953_PAD_SINK, |
| .sink_stream = 0, |
| .source_pad = UB953_PAD_SOURCE, |
| .source_stream = 0, |
| .flags = V4L2_SUBDEV_ROUTE_FL_ACTIVE, |
| }, |
| }; |
| |
| struct v4l2_subdev_krouting routing = { |
| .num_routes = ARRAY_SIZE(routes), |
| .routes = routes, |
| }; |
| |
| return _ub953_set_routing(sd, state, &routing); |
| } |
| |
| static int ub953_log_status(struct v4l2_subdev *sd) |
| { |
| struct ub953_data *priv = sd_to_ub953(sd); |
| struct device *dev = &priv->client->dev; |
| u8 v = 0, v1 = 0, v2 = 0; |
| unsigned int i; |
| char id[UB953_REG_FPD3_RX_ID_LEN]; |
| u8 gpio_local_data = 0; |
| u8 gpio_input_ctrl = 0; |
| u8 gpio_pin_sts = 0; |
| |
| for (i = 0; i < sizeof(id); i++) |
| ub953_read(priv, UB953_REG_FPD3_RX_ID(i), &id[i]); |
| |
| dev_info(dev, "ID '%.*s'\n", (int)sizeof(id), id); |
| |
| ub953_read(priv, UB953_REG_GENERAL_STATUS, &v); |
| dev_info(dev, "GENERAL_STATUS %#02x\n", v); |
| |
| ub953_read(priv, UB953_REG_CRC_ERR_CNT1, &v1); |
| ub953_read(priv, UB953_REG_CRC_ERR_CNT2, &v2); |
| dev_info(dev, "CRC error count %u\n", v1 | (v2 << 8)); |
| |
| ub953_read(priv, UB953_REG_CSI_ERR_CNT, &v); |
| dev_info(dev, "CSI error count %u\n", v); |
| |
| ub953_read(priv, UB953_REG_CSI_ERR_STATUS, &v); |
| dev_info(dev, "CSI_ERR_STATUS %#02x\n", v); |
| |
| ub953_read(priv, UB953_REG_CSI_ERR_DLANE01, &v); |
| dev_info(dev, "CSI_ERR_DLANE01 %#02x\n", v); |
| |
| ub953_read(priv, UB953_REG_CSI_ERR_DLANE23, &v); |
| dev_info(dev, "CSI_ERR_DLANE23 %#02x\n", v); |
| |
| ub953_read(priv, UB953_REG_CSI_ERR_CLK_LANE, &v); |
| dev_info(dev, "CSI_ERR_CLK_LANE %#02x\n", v); |
| |
| ub953_read(priv, UB953_REG_CSI_PKT_HDR_VC_ID, &v); |
| dev_info(dev, "CSI packet header VC %u ID %u\n", v >> 6, v & 0x3f); |
| |
| ub953_read(priv, UB953_REG_PKT_HDR_WC_LSB, &v1); |
| ub953_read(priv, UB953_REG_PKT_HDR_WC_MSB, &v2); |
| dev_info(dev, "CSI packet header WC %u\n", (v2 << 8) | v1); |
| |
| ub953_read(priv, UB953_REG_CSI_ECC, &v); |
| dev_info(dev, "CSI ECC %#02x\n", v); |
| |
| ub953_read(priv, UB953_REG_LOCAL_GPIO_DATA, &gpio_local_data); |
| ub953_read(priv, UB953_REG_GPIO_INPUT_CTRL, &gpio_input_ctrl); |
| ub953_read(priv, UB953_REG_GPIO_PIN_STS, &gpio_pin_sts); |
| |
| for (i = 0; i < UB953_NUM_GPIOS; i++) { |
| dev_info(dev, |
| "GPIO%u: remote: %u is_input: %u is_output: %u val: %u sts: %u\n", |
| i, |
| !!(gpio_local_data & UB953_REG_LOCAL_GPIO_DATA_GPIO_RMTEN(i)), |
| !!(gpio_input_ctrl & UB953_REG_GPIO_INPUT_CTRL_INPUT_EN(i)), |
| !!(gpio_input_ctrl & UB953_REG_GPIO_INPUT_CTRL_OUT_EN(i)), |
| !!(gpio_local_data & UB953_REG_LOCAL_GPIO_DATA_GPIO_OUT_SRC(i)), |
| !!(gpio_pin_sts & UB953_REG_GPIO_PIN_STS_GPIO_STS(i))); |
| } |
| |
| return 0; |
| } |
| |
| static int ub953_enable_streams(struct v4l2_subdev *sd, |
| struct v4l2_subdev_state *state, u32 pad, |
| u64 streams_mask) |
| { |
| struct ub953_data *priv = sd_to_ub953(sd); |
| u64 sink_streams; |
| int ret; |
| |
| sink_streams = v4l2_subdev_state_xlate_streams(state, UB953_PAD_SOURCE, |
| UB953_PAD_SINK, |
| &streams_mask); |
| |
| ret = v4l2_subdev_enable_streams(priv->source_sd, priv->source_sd_pad, |
| sink_streams); |
| if (ret) |
| return ret; |
| |
| priv->enabled_source_streams |= streams_mask; |
| |
| return 0; |
| } |
| |
| static int ub953_disable_streams(struct v4l2_subdev *sd, |
| struct v4l2_subdev_state *state, u32 pad, |
| u64 streams_mask) |
| { |
| struct ub953_data *priv = sd_to_ub953(sd); |
| u64 sink_streams; |
| int ret; |
| |
| sink_streams = v4l2_subdev_state_xlate_streams(state, UB953_PAD_SOURCE, |
| UB953_PAD_SINK, |
| &streams_mask); |
| |
| ret = v4l2_subdev_disable_streams(priv->source_sd, priv->source_sd_pad, |
| sink_streams); |
| if (ret) |
| return ret; |
| |
| priv->enabled_source_streams &= ~streams_mask; |
| |
| return 0; |
| } |
| |
| static const struct v4l2_subdev_pad_ops ub953_pad_ops = { |
| .enable_streams = ub953_enable_streams, |
| .disable_streams = ub953_disable_streams, |
| .set_routing = ub953_set_routing, |
| .get_frame_desc = ub953_get_frame_desc, |
| .get_fmt = v4l2_subdev_get_fmt, |
| .set_fmt = ub953_set_fmt, |
| }; |
| |
| static const struct v4l2_subdev_core_ops ub953_subdev_core_ops = { |
| .log_status = ub953_log_status, |
| .subscribe_event = v4l2_ctrl_subdev_subscribe_event, |
| .unsubscribe_event = v4l2_event_subdev_unsubscribe, |
| }; |
| |
| static const struct v4l2_subdev_ops ub953_subdev_ops = { |
| .core = &ub953_subdev_core_ops, |
| .pad = &ub953_pad_ops, |
| }; |
| |
| static const struct v4l2_subdev_internal_ops ub953_internal_ops = { |
| .init_state = ub953_init_state, |
| }; |
| |
| static const struct media_entity_operations ub953_entity_ops = { |
| .link_validate = v4l2_subdev_link_validate, |
| }; |
| |
| static int ub953_notify_bound(struct v4l2_async_notifier *notifier, |
| struct v4l2_subdev *source_subdev, |
| struct v4l2_async_connection *asd) |
| { |
| struct ub953_data *priv = sd_to_ub953(notifier->sd); |
| struct device *dev = &priv->client->dev; |
| int ret; |
| |
| ret = media_entity_get_fwnode_pad(&source_subdev->entity, |
| source_subdev->fwnode, |
| MEDIA_PAD_FL_SOURCE); |
| if (ret < 0) { |
| dev_err(dev, "Failed to find pad for %s\n", |
| source_subdev->name); |
| return ret; |
| } |
| |
| priv->source_sd = source_subdev; |
| priv->source_sd_pad = ret; |
| |
| ret = media_create_pad_link(&source_subdev->entity, priv->source_sd_pad, |
| &priv->sd.entity, 0, |
| MEDIA_LNK_FL_ENABLED | |
| MEDIA_LNK_FL_IMMUTABLE); |
| if (ret) { |
| dev_err(dev, "Unable to link %s:%u -> %s:0\n", |
| source_subdev->name, priv->source_sd_pad, |
| priv->sd.name); |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static const struct v4l2_async_notifier_operations ub953_notify_ops = { |
| .bound = ub953_notify_bound, |
| }; |
| |
| static int ub953_v4l2_notifier_register(struct ub953_data *priv) |
| { |
| struct device *dev = &priv->client->dev; |
| struct v4l2_async_connection *asd; |
| struct fwnode_handle *ep_fwnode; |
| int ret; |
| |
| ep_fwnode = fwnode_graph_get_endpoint_by_id(dev_fwnode(dev), |
| UB953_PAD_SINK, 0, 0); |
| if (!ep_fwnode) { |
| dev_err(dev, "No graph endpoint\n"); |
| return -ENODEV; |
| } |
| |
| v4l2_async_subdev_nf_init(&priv->notifier, &priv->sd); |
| |
| asd = v4l2_async_nf_add_fwnode_remote(&priv->notifier, ep_fwnode, |
| struct v4l2_async_connection); |
| |
| fwnode_handle_put(ep_fwnode); |
| |
| if (IS_ERR(asd)) { |
| dev_err(dev, "Failed to add subdev: %ld", PTR_ERR(asd)); |
| v4l2_async_nf_cleanup(&priv->notifier); |
| return PTR_ERR(asd); |
| } |
| |
| priv->notifier.ops = &ub953_notify_ops; |
| |
| ret = v4l2_async_nf_register(&priv->notifier); |
| if (ret) { |
| dev_err(dev, "Failed to register subdev_notifier"); |
| v4l2_async_nf_cleanup(&priv->notifier); |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static void ub953_v4l2_notifier_unregister(struct ub953_data *priv) |
| { |
| v4l2_async_nf_unregister(&priv->notifier); |
| v4l2_async_nf_cleanup(&priv->notifier); |
| } |
| |
| /* |
| * Probing |
| */ |
| |
| static int ub953_i2c_master_init(struct ub953_data *priv) |
| { |
| /* i2c fast mode */ |
| u32 ref = 26250000; |
| u32 scl_high = 915; /* ns */ |
| u32 scl_low = 1641; /* ns */ |
| int ret; |
| |
| scl_high = div64_u64((u64)scl_high * ref, 1000000000) - 5; |
| scl_low = div64_u64((u64)scl_low * ref, 1000000000) - 5; |
| |
| ret = ub953_write(priv, UB953_REG_SCL_HIGH_TIME, scl_high); |
| if (ret) |
| return ret; |
| |
| ret = ub953_write(priv, UB953_REG_SCL_LOW_TIME, scl_low); |
| if (ret) |
| return ret; |
| |
| return 0; |
| } |
| |
| static u64 ub953_get_fc_rate(struct ub953_data *priv) |
| { |
| switch (priv->mode) { |
| case UB953_MODE_SYNC: |
| if (priv->hw_data->is_ub971) |
| return priv->plat_data->bc_rate * 160ull; |
| else |
| return priv->plat_data->bc_rate / 2 * 160ull; |
| |
| case UB953_MODE_NONSYNC_EXT: |
| /* CLKIN_DIV = 1 always */ |
| return clk_get_rate(priv->clkin) * 80ull; |
| |
| default: |
| /* Not supported */ |
| return 0; |
| } |
| } |
| |
| static unsigned long ub953_calc_clkout_ub953(struct ub953_data *priv, |
| unsigned long target, u64 fc, |
| u8 *hs_div, u8 *m, u8 *n) |
| { |
| /* |
| * We always use 4 as a pre-divider (HS_CLK_DIV = 2). |
| * |
| * According to the datasheet: |
| * - "HS_CLK_DIV typically should be set to either 16, 8, or 4 (default)." |
| * - "if it is not possible to have an integer ratio of N/M, it is best to |
| * select a smaller value for HS_CLK_DIV. |
| * |
| * For above reasons the default HS_CLK_DIV seems the best in the average |
| * case. Use always that value to keep the code simple. |
| */ |
| static const unsigned long hs_clk_div = 4; |
| |
| u64 fc_divided; |
| unsigned long mul, div; |
| unsigned long res; |
| |
| /* clkout = fc / hs_clk_div * m / n */ |
| |
| fc_divided = div_u64(fc, hs_clk_div); |
| |
| rational_best_approximation(target, fc_divided, (1 << 5) - 1, |
| (1 << 8) - 1, &mul, &div); |
| |
| res = div_u64(fc_divided * mul, div); |
| |
| *hs_div = hs_clk_div; |
| *m = mul; |
| *n = div; |
| |
| return res; |
| } |
| |
| static unsigned long ub953_calc_clkout_ub971(struct ub953_data *priv, |
| unsigned long target, u64 fc, |
| u8 *m, u8 *n) |
| { |
| u64 fc_divided; |
| unsigned long mul, div; |
| unsigned long res; |
| |
| /* clkout = fc * m / (8 * n) */ |
| |
| fc_divided = div_u64(fc, 8); |
| |
| rational_best_approximation(target, fc_divided, (1 << 5) - 1, |
| (1 << 8) - 1, &mul, &div); |
| |
| res = div_u64(fc_divided * mul, div); |
| |
| *m = mul; |
| *n = div; |
| |
| return res; |
| } |
| |
| static void ub953_calc_clkout_params(struct ub953_data *priv, |
| unsigned long target_rate, |
| struct ub953_clkout_data *clkout_data) |
| { |
| struct device *dev = &priv->client->dev; |
| unsigned long clkout_rate; |
| u64 fc_rate; |
| |
| fc_rate = ub953_get_fc_rate(priv); |
| |
| if (priv->hw_data->is_ub971) { |
| u8 m, n; |
| |
| clkout_rate = ub953_calc_clkout_ub971(priv, target_rate, |
| fc_rate, &m, &n); |
| |
| clkout_data->m = m; |
| clkout_data->n = n; |
| |
| dev_dbg(dev, "%s %llu * %u / (8 * %u) = %lu (requested %lu)", |
| __func__, fc_rate, m, n, clkout_rate, target_rate); |
| } else { |
| u8 hs_div, m, n; |
| |
| clkout_rate = ub953_calc_clkout_ub953(priv, target_rate, |
| fc_rate, &hs_div, &m, &n); |
| |
| clkout_data->hs_div = hs_div; |
| clkout_data->m = m; |
| clkout_data->n = n; |
| |
| dev_dbg(dev, "%s %llu / %u * %u / %u = %lu (requested %lu)", |
| __func__, fc_rate, hs_div, m, n, clkout_rate, |
| target_rate); |
| } |
| |
| clkout_data->rate = clkout_rate; |
| } |
| |
| static void ub953_write_clkout_regs(struct ub953_data *priv, |
| const struct ub953_clkout_data *clkout_data) |
| { |
| u8 clkout_ctrl0, clkout_ctrl1; |
| |
| if (priv->hw_data->is_ub971) |
| clkout_ctrl0 = clkout_data->m; |
| else |
| clkout_ctrl0 = (__ffs(clkout_data->hs_div) << 5) | |
| clkout_data->m; |
| |
| clkout_ctrl1 = clkout_data->n; |
| |
| ub953_write(priv, UB953_REG_CLKOUT_CTRL0, clkout_ctrl0); |
| ub953_write(priv, UB953_REG_CLKOUT_CTRL1, clkout_ctrl1); |
| } |
| |
| static unsigned long ub953_clkout_recalc_rate(struct clk_hw *hw, |
| unsigned long parent_rate) |
| { |
| struct ub953_data *priv = container_of(hw, struct ub953_data, clkout_clk_hw); |
| struct device *dev = &priv->client->dev; |
| u8 ctrl0, ctrl1; |
| u32 mul, div; |
| u64 fc_rate; |
| u32 hs_clk_div; |
| u64 rate; |
| int ret; |
| |
| ret = ub953_read(priv, UB953_REG_CLKOUT_CTRL0, &ctrl0); |
| if (ret) { |
| dev_err(dev, "Failed to read CLKOUT_CTRL0: %d\n", ret); |
| return 0; |
| } |
| |
| ret = ub953_read(priv, UB953_REG_CLKOUT_CTRL1, &ctrl1); |
| if (ret) { |
| dev_err(dev, "Failed to read CLKOUT_CTRL1: %d\n", ret); |
| return 0; |
| } |
| |
| fc_rate = ub953_get_fc_rate(priv); |
| |
| if (priv->hw_data->is_ub971) { |
| mul = ctrl0 & 0x1f; |
| div = ctrl1; |
| |
| if (div == 0) |
| return 0; |
| |
| rate = div_u64(fc_rate * mul, 8 * div); |
| |
| dev_dbg(dev, "clkout: fc rate %llu, mul %u, div %u = %llu\n", |
| fc_rate, mul, div, rate); |
| } else { |
| mul = ctrl0 & 0x1f; |
| hs_clk_div = 1 << (ctrl0 >> 5); |
| div = ctrl1; |
| |
| if (div == 0) |
| return 0; |
| |
| rate = div_u64(div_u64(fc_rate, hs_clk_div) * mul, div); |
| |
| dev_dbg(dev, |
| "clkout: fc rate %llu, hs_clk_div %u, mul %u, div %u = %llu\n", |
| fc_rate, hs_clk_div, mul, div, rate); |
| } |
| |
| return rate; |
| } |
| |
| static long ub953_clkout_round_rate(struct clk_hw *hw, unsigned long rate, |
| unsigned long *parent_rate) |
| { |
| struct ub953_data *priv = container_of(hw, struct ub953_data, clkout_clk_hw); |
| struct ub953_clkout_data clkout_data; |
| |
| ub953_calc_clkout_params(priv, rate, &clkout_data); |
| |
| return clkout_data.rate; |
| } |
| |
| static int ub953_clkout_set_rate(struct clk_hw *hw, unsigned long rate, |
| unsigned long parent_rate) |
| { |
| struct ub953_data *priv = container_of(hw, struct ub953_data, clkout_clk_hw); |
| struct ub953_clkout_data clkout_data; |
| |
| ub953_calc_clkout_params(priv, rate, &clkout_data); |
| |
| dev_dbg(&priv->client->dev, "%s %lu (requested %lu)\n", __func__, |
| clkout_data.rate, rate); |
| |
| ub953_write_clkout_regs(priv, &clkout_data); |
| |
| return 0; |
| } |
| |
| static const struct clk_ops ub953_clkout_ops = { |
| .recalc_rate = ub953_clkout_recalc_rate, |
| .round_rate = ub953_clkout_round_rate, |
| .set_rate = ub953_clkout_set_rate, |
| }; |
| |
| static int ub953_register_clkout(struct ub953_data *priv) |
| { |
| struct device *dev = &priv->client->dev; |
| const struct clk_init_data init = { |
| .name = kasprintf(GFP_KERNEL, "ds90%s.%s.clk_out", |
| priv->hw_data->model, dev_name(dev)), |
| .ops = &ub953_clkout_ops, |
| }; |
| struct ub953_clkout_data clkout_data; |
| int ret; |
| |
| if (!init.name) |
| return -ENOMEM; |
| |
| /* Initialize clkout to 25MHz by default */ |
| ub953_calc_clkout_params(priv, UB953_DEFAULT_CLKOUT_RATE, &clkout_data); |
| ub953_write_clkout_regs(priv, &clkout_data); |
| |
| priv->clkout_clk_hw.init = &init; |
| |
| ret = devm_clk_hw_register(dev, &priv->clkout_clk_hw); |
| kfree(init.name); |
| if (ret) |
| return dev_err_probe(dev, ret, "Cannot register clock HW\n"); |
| |
| ret = devm_of_clk_add_hw_provider(dev, of_clk_hw_simple_get, |
| &priv->clkout_clk_hw); |
| if (ret) |
| return dev_err_probe(dev, ret, |
| "Cannot add OF clock provider\n"); |
| |
| return 0; |
| } |
| |
| static int ub953_add_i2c_adapter(struct ub953_data *priv) |
| { |
| struct device *dev = &priv->client->dev; |
| struct fwnode_handle *i2c_handle; |
| int ret; |
| |
| i2c_handle = device_get_named_child_node(dev, "i2c"); |
| if (!i2c_handle) |
| return 0; |
| |
| ret = i2c_atr_add_adapter(priv->plat_data->atr, priv->plat_data->port, |
| dev, i2c_handle); |
| |
| fwnode_handle_put(i2c_handle); |
| |
| if (ret) |
| return ret; |
| |
| return 0; |
| } |
| |
| static const struct regmap_config ub953_regmap_config = { |
| .name = "ds90ub953", |
| .reg_bits = 8, |
| .val_bits = 8, |
| .reg_format_endian = REGMAP_ENDIAN_DEFAULT, |
| .val_format_endian = REGMAP_ENDIAN_DEFAULT, |
| }; |
| |
| static int ub953_parse_dt(struct ub953_data *priv) |
| { |
| struct device *dev = &priv->client->dev; |
| struct v4l2_fwnode_endpoint vep = { |
| .bus_type = V4L2_MBUS_CSI2_DPHY, |
| }; |
| struct fwnode_handle *ep_fwnode; |
| unsigned char nlanes; |
| int ret; |
| |
| ep_fwnode = fwnode_graph_get_endpoint_by_id(dev_fwnode(dev), |
| UB953_PAD_SINK, 0, 0); |
| if (!ep_fwnode) |
| return dev_err_probe(dev, -ENOENT, "no endpoint found\n"); |
| |
| ret = v4l2_fwnode_endpoint_parse(ep_fwnode, &vep); |
| |
| fwnode_handle_put(ep_fwnode); |
| |
| if (ret) |
| return dev_err_probe(dev, ret, |
| "failed to parse sink endpoint data\n"); |
| |
| nlanes = vep.bus.mipi_csi2.num_data_lanes; |
| if (nlanes != 1 && nlanes != 2 && nlanes != 4) |
| return dev_err_probe(dev, -EINVAL, |
| "bad number of data-lanes: %u\n", nlanes); |
| |
| priv->num_data_lanes = nlanes; |
| |
| priv->non_continous_clk = vep.bus.mipi_csi2.flags & |
| V4L2_MBUS_CSI2_NONCONTINUOUS_CLOCK; |
| |
| return 0; |
| } |
| |
| static int ub953_hw_init(struct ub953_data *priv) |
| { |
| struct device *dev = &priv->client->dev; |
| bool mode_override; |
| int ret; |
| u8 v; |
| |
| ret = ub953_read(priv, UB953_REG_MODE_SEL, &v); |
| if (ret) |
| return ret; |
| |
| if (!(v & UB953_REG_MODE_SEL_MODE_DONE)) |
| return dev_err_probe(dev, -EIO, "Mode value not stabilized\n"); |
| |
| mode_override = v & UB953_REG_MODE_SEL_MODE_OVERRIDE; |
| |
| switch (v & UB953_REG_MODE_SEL_MODE_MASK) { |
| case 0: |
| priv->mode = UB953_MODE_SYNC; |
| break; |
| case 2: |
| priv->mode = UB953_MODE_NONSYNC_EXT; |
| break; |
| case 3: |
| priv->mode = UB953_MODE_NONSYNC_INT; |
| break; |
| case 5: |
| priv->mode = UB953_MODE_DVP; |
| break; |
| default: |
| return dev_err_probe(dev, -EIO, |
| "Invalid mode in mode register\n"); |
| } |
| |
| dev_dbg(dev, "mode from %s: %#x\n", mode_override ? "reg" : "strap", |
| priv->mode); |
| |
| if (priv->mode != UB953_MODE_SYNC && |
| priv->mode != UB953_MODE_NONSYNC_EXT) |
| return dev_err_probe(dev, -ENODEV, |
| "Unsupported mode selected: %u\n", |
| priv->mode); |
| |
| if (priv->mode == UB953_MODE_NONSYNC_EXT && !priv->clkin) |
| return dev_err_probe(dev, -EINVAL, |
| "clkin required for non-sync ext mode\n"); |
| |
| ret = ub953_read(priv, UB953_REG_REV_MASK_ID, &v); |
| if (ret) |
| return dev_err_probe(dev, ret, "Failed to read revision"); |
| |
| dev_info(dev, "Found %s rev/mask %#04x\n", priv->hw_data->model, v); |
| |
| ret = ub953_read(priv, UB953_REG_GENERAL_CFG, &v); |
| if (ret) |
| return ret; |
| |
| dev_dbg(dev, "i2c strap setting %s V\n", |
| (v & UB953_REG_GENERAL_CFG_I2C_STRAP_MODE) ? "1.8" : "3.3"); |
| |
| ret = ub953_i2c_master_init(priv); |
| if (ret) |
| return dev_err_probe(dev, ret, "i2c init failed\n"); |
| |
| ub953_write(priv, UB953_REG_GENERAL_CFG, |
| (priv->non_continous_clk ? 0 : UB953_REG_GENERAL_CFG_CONT_CLK) | |
| ((priv->num_data_lanes - 1) << UB953_REG_GENERAL_CFG_CSI_LANE_SEL_SHIFT) | |
| UB953_REG_GENERAL_CFG_CRC_TX_GEN_ENABLE); |
| |
| return 0; |
| } |
| |
| static int ub953_subdev_init(struct ub953_data *priv) |
| { |
| struct device *dev = &priv->client->dev; |
| int ret; |
| |
| v4l2_i2c_subdev_init(&priv->sd, priv->client, &ub953_subdev_ops); |
| priv->sd.internal_ops = &ub953_internal_ops; |
| |
| priv->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE | |
| V4L2_SUBDEV_FL_HAS_EVENTS | V4L2_SUBDEV_FL_STREAMS; |
| priv->sd.entity.function = MEDIA_ENT_F_VID_IF_BRIDGE; |
| priv->sd.entity.ops = &ub953_entity_ops; |
| |
| priv->pads[0].flags = MEDIA_PAD_FL_SINK; |
| priv->pads[1].flags = MEDIA_PAD_FL_SOURCE; |
| |
| ret = media_entity_pads_init(&priv->sd.entity, 2, priv->pads); |
| if (ret) |
| return dev_err_probe(dev, ret, "Failed to init pads\n"); |
| |
| ret = v4l2_subdev_init_finalize(&priv->sd); |
| if (ret) |
| goto err_entity_cleanup; |
| |
| ret = ub953_v4l2_notifier_register(priv); |
| if (ret) { |
| dev_err_probe(dev, ret, |
| "v4l2 subdev notifier register failed\n"); |
| goto err_free_state; |
| } |
| |
| ret = v4l2_async_register_subdev(&priv->sd); |
| if (ret) { |
| dev_err_probe(dev, ret, "v4l2_async_register_subdev error\n"); |
| goto err_unreg_notif; |
| } |
| |
| return 0; |
| |
| err_unreg_notif: |
| ub953_v4l2_notifier_unregister(priv); |
| err_free_state: |
| v4l2_subdev_cleanup(&priv->sd); |
| err_entity_cleanup: |
| media_entity_cleanup(&priv->sd.entity); |
| |
| return ret; |
| } |
| |
| static void ub953_subdev_uninit(struct ub953_data *priv) |
| { |
| v4l2_async_unregister_subdev(&priv->sd); |
| ub953_v4l2_notifier_unregister(priv); |
| v4l2_subdev_cleanup(&priv->sd); |
| fwnode_handle_put(priv->sd.fwnode); |
| media_entity_cleanup(&priv->sd.entity); |
| } |
| |
| static int ub953_probe(struct i2c_client *client) |
| { |
| struct device *dev = &client->dev; |
| struct ub953_data *priv; |
| int ret; |
| |
| priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); |
| if (!priv) |
| return -ENOMEM; |
| |
| priv->client = client; |
| |
| priv->hw_data = device_get_match_data(dev); |
| |
| priv->plat_data = dev_get_platdata(&client->dev); |
| if (!priv->plat_data) |
| return dev_err_probe(dev, -ENODEV, "Platform data missing\n"); |
| |
| mutex_init(&priv->reg_lock); |
| |
| /* |
| * Initialize to invalid values so that the first reg writes will |
| * configure the target. |
| */ |
| priv->current_indirect_target = 0xff; |
| |
| priv->regmap = devm_regmap_init_i2c(client, &ub953_regmap_config); |
| if (IS_ERR(priv->regmap)) { |
| ret = PTR_ERR(priv->regmap); |
| dev_err_probe(dev, ret, "Failed to init regmap\n"); |
| goto err_mutex_destroy; |
| } |
| |
| priv->clkin = devm_clk_get_optional(dev, "clkin"); |
| if (IS_ERR(priv->clkin)) { |
| ret = PTR_ERR(priv->clkin); |
| dev_err_probe(dev, ret, "failed to parse 'clkin'\n"); |
| goto err_mutex_destroy; |
| } |
| |
| ret = ub953_parse_dt(priv); |
| if (ret) |
| goto err_mutex_destroy; |
| |
| ret = ub953_hw_init(priv); |
| if (ret) |
| goto err_mutex_destroy; |
| |
| ret = ub953_gpiochip_probe(priv); |
| if (ret) { |
| dev_err_probe(dev, ret, "Failed to init gpiochip\n"); |
| goto err_mutex_destroy; |
| } |
| |
| ret = ub953_register_clkout(priv); |
| if (ret) { |
| dev_err_probe(dev, ret, "Failed to register clkout\n"); |
| goto err_gpiochip_remove; |
| } |
| |
| ret = ub953_subdev_init(priv); |
| if (ret) |
| goto err_gpiochip_remove; |
| |
| ret = ub953_add_i2c_adapter(priv); |
| if (ret) { |
| dev_err_probe(dev, ret, "failed to add remote i2c adapter\n"); |
| goto err_subdev_uninit; |
| } |
| |
| return 0; |
| |
| err_subdev_uninit: |
| ub953_subdev_uninit(priv); |
| err_gpiochip_remove: |
| ub953_gpiochip_remove(priv); |
| err_mutex_destroy: |
| mutex_destroy(&priv->reg_lock); |
| |
| return ret; |
| } |
| |
| static void ub953_remove(struct i2c_client *client) |
| { |
| struct v4l2_subdev *sd = i2c_get_clientdata(client); |
| struct ub953_data *priv = sd_to_ub953(sd); |
| |
| i2c_atr_del_adapter(priv->plat_data->atr, priv->plat_data->port); |
| |
| ub953_subdev_uninit(priv); |
| |
| ub953_gpiochip_remove(priv); |
| mutex_destroy(&priv->reg_lock); |
| } |
| |
| static const struct ub953_hw_data ds90ub953_hw = { |
| .model = "ub953", |
| }; |
| |
| static const struct ub953_hw_data ds90ub971_hw = { |
| .model = "ub971", |
| .is_ub971 = true, |
| }; |
| |
| static const struct i2c_device_id ub953_id[] = { |
| { "ds90ub953-q1", (kernel_ulong_t)&ds90ub953_hw }, |
| { "ds90ub971-q1", (kernel_ulong_t)&ds90ub971_hw }, |
| {} |
| }; |
| MODULE_DEVICE_TABLE(i2c, ub953_id); |
| |
| static const struct of_device_id ub953_dt_ids[] = { |
| { .compatible = "ti,ds90ub953-q1", .data = &ds90ub953_hw }, |
| { .compatible = "ti,ds90ub971-q1", .data = &ds90ub971_hw }, |
| {} |
| }; |
| MODULE_DEVICE_TABLE(of, ub953_dt_ids); |
| |
| static struct i2c_driver ds90ub953_driver = { |
| .probe = ub953_probe, |
| .remove = ub953_remove, |
| .id_table = ub953_id, |
| .driver = { |
| .name = "ds90ub953", |
| .of_match_table = ub953_dt_ids, |
| }, |
| }; |
| module_i2c_driver(ds90ub953_driver); |
| |
| MODULE_LICENSE("GPL"); |
| MODULE_DESCRIPTION("Texas Instruments FPD-Link III/IV CSI-2 Serializers Driver"); |
| MODULE_AUTHOR("Luca Ceresoli <luca@lucaceresoli.net>"); |
| MODULE_AUTHOR("Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>"); |
| MODULE_IMPORT_NS(I2C_ATR); |