blob: 31c0a69771c47a431b72898e1063d00d7d8d1823 [file] [log] [blame]
// SPDX-License-Identifier: ISC
/*
* Device Tree include file for Intel reference designs for the
* XScale Network Processors in the IXP 4xx series. Common device
* set-up for IXDP425, IXCDP1100, KIXRP435 and IXDP465.
*/
/ {
memory@0 {
/*
* The board supports up to 256 MB of memory. Here we put in
* 64 MB and this may be modified by the boot loader.
*/
device_type = "memory";
reg = <0x00000000 0x4000000>;
};
chosen {
bootargs = "console=ttyS0,115200n8";
stdout-path = "uart0:115200n8";
};
aliases {
serial0 = &uart0;
};
i2c {
compatible = "i2c-gpio";
sda-gpios = <&gpio0 7 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
scl-gpios = <&gpio0 6 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
#address-cells = <1>;
#size-cells = <0>;
eeprom@50 {
/*
* Philips PCF8582C-2T/03 512byte I2C EEPROM
* should behave like an Atmel 24c04.
*/
compatible = "atmel,24c04";
reg = <0x50>;
pagesize = <16>;
size = <512>;
read-only;
};
};
soc {
bus@c4000000 {
/* Flash memory defined per-variant */
nand-controller@3,0 {
/* Some designs have a NAND on CS3 enable it here if present */
status = "disabled";
/*
* gen_nand needs to be extended and documented to get
* command byte = 1 and address byte = 2 from the device
* tree.
*/
compatible = "gen_nand";
/* Expansion bus set-up */
intel,ixp4xx-eb-t1 = <0>;
intel,ixp4xx-eb-t2 = <0>;
intel,ixp4xx-eb-t3 = <1>; // 1 cycle extra strobe phase
intel,ixp4xx-eb-t4 = <0>;
intel,ixp4xx-eb-t5 = <0>;
intel,ixp4xx-eb-cycle-type = <0>; // Intel cycle type
intel,ixp4xx-eb-byte-access-on-halfword = <0>;
intel,ixp4xx-eb-mux-address-and-data = <0>;
intel,ixp4xx-eb-ahb-split-transfers = <0>;
intel,ixp4xx-eb-write-enable = <1>;
intel,ixp4xx-eb-byte-access = <1>;
/* 512 bytes memory window */
reg = <3 0x00000000 0x200>;
nand-on-flash-bbt;
nand-ecc-mode = "soft_bch";
nand-ecc-step-size = <512>;
nand-ecc-strength = <4>;
nce-gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; /* NCE */
label = "ixp400 NAND";
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
fs@0 {
label = "ixp400 NAND FS 0";
reg = <0x0 0x800000>;
};
fs@800000 {
label = "ixp400 NAND FS 1";
reg = <0x800000 0x0>;
};
};
};
};
pci@c0000000 {
status = "okay";
/*
* Taken from IXDP425 PCI boardfile.
* PCI slots on the BIXMB425BD base card.
* We have up to 4 slots (IDSEL) with 4 swizzled IRQs.
*/
#interrupt-cells = <1>;
interrupt-map-mask = <0xf800 0 0 7>;
interrupt-map =
/* IDSEL 1 */
<0x0800 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 11 */
<0x0800 0 0 2 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 1 is irq 10 */
<0x0800 0 0 3 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 1 is irq 9 */
<0x0800 0 0 4 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 1 is irq 8 */
/* IDSEL 2 */
<0x1000 0 0 1 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 10 */
<0x1000 0 0 2 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 2 is irq 9 */
<0x1000 0 0 3 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 2 is irq 8 */
<0x1000 0 0 4 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 2 is irq 11 */
/* IDSEL 3 */
<0x1800 0 0 1 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 3 is irq 9 */
<0x1800 0 0 2 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 3 is irq 8 */
<0x1800 0 0 3 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 3 is irq 11 */
<0x1800 0 0 4 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 3 is irq 10 */
/* IDSEL 4 */
<0x2000 0 0 1 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 4 is irq 8 */
<0x2000 0 0 2 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 4 is irq 11 */
<0x2000 0 0 3 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 4 is irq 10 */
<0x2000 0 0 4 &gpio0 9 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 4 is irq 9 */
};
};
};