| # SPDX-License-Identifier: GPL-2.0-only |
| # |
| # Multimedia Video device configuration |
| # |
| |
| if VIDEO_DEV |
| |
| comment "IR I2C driver auto-selected by 'Autoselect ancillary drivers'" |
| depends on MEDIA_SUBDRV_AUTOSELECT && I2C && RC_CORE |
| |
| config VIDEO_IR_I2C |
| tristate "I2C module for IR" if !MEDIA_SUBDRV_AUTOSELECT || EXPERT |
| depends on I2C && RC_CORE |
| default y |
| help |
| Most boards have an IR chip directly connected via GPIO. However, |
| some video boards have the IR connected via I2C bus. |
| |
| If your board doesn't have an I2C IR chip, you may disable this |
| option. |
| |
| In doubt, say Y. |
| |
| # |
| # V4L2 I2C drivers that are related with Camera support |
| # |
| |
| menuconfig VIDEO_CAMERA_SENSOR |
| bool "Camera sensor devices" |
| depends on MEDIA_CAMERA_SUPPORT && I2C |
| select MEDIA_CONTROLLER |
| select V4L2_FWNODE |
| select VIDEO_V4L2_SUBDEV_API |
| default y |
| |
| if VIDEO_CAMERA_SENSOR |
| |
| config VIDEO_APTINA_PLL |
| tristate |
| |
| config VIDEO_CCS_PLL |
| tristate |
| |
| config VIDEO_AR0521 |
| tristate "ON Semiconductor AR0521 sensor support" |
| help |
| This is a Video4Linux2 sensor driver for the ON Semiconductor |
| AR0521 camera. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called ar0521. |
| |
| config VIDEO_HI556 |
| tristate "Hynix Hi-556 sensor support" |
| help |
| This is a Video4Linux2 sensor driver for the Hynix |
| Hi-556 camera. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called hi556. |
| |
| config VIDEO_HI846 |
| tristate "Hynix Hi-846 sensor support" |
| help |
| This is a Video4Linux2 sensor driver for the Hynix |
| Hi-846 camera. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called hi846. |
| |
| config VIDEO_HI847 |
| tristate "Hynix Hi-847 sensor support" |
| help |
| This is a Video4Linux2 sensor driver for the Hynix |
| Hi-847 camera. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called hi847. |
| |
| config VIDEO_IMX208 |
| tristate "Sony IMX208 sensor support" |
| help |
| This is a Video4Linux2 sensor driver for the Sony |
| IMX208 camera. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called imx208. |
| |
| config VIDEO_IMX214 |
| tristate "Sony IMX214 sensor support" |
| depends on GPIOLIB |
| select REGMAP_I2C |
| help |
| This is a Video4Linux2 sensor driver for the Sony |
| IMX214 camera. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called imx214. |
| |
| config VIDEO_IMX219 |
| tristate "Sony IMX219 sensor support" |
| select V4L2_CCI_I2C |
| help |
| This is a Video4Linux2 sensor driver for the Sony |
| IMX219 camera. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called imx219. |
| |
| config VIDEO_IMX258 |
| tristate "Sony IMX258 sensor support" |
| help |
| This is a Video4Linux2 sensor driver for the Sony |
| IMX258 camera. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called imx258. |
| |
| config VIDEO_IMX274 |
| tristate "Sony IMX274 sensor support" |
| select REGMAP_I2C |
| help |
| This is a V4L2 sensor driver for the Sony IMX274 |
| CMOS image sensor. |
| |
| config VIDEO_IMX290 |
| tristate "Sony IMX290 sensor support" |
| select REGMAP_I2C |
| select V4L2_CCI_I2C |
| help |
| This is a Video4Linux2 sensor driver for the Sony |
| IMX290 camera sensor. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called imx290. |
| |
| config VIDEO_IMX296 |
| tristate "Sony IMX296 sensor support" |
| help |
| This is a Video4Linux2 sensor driver for the Sony |
| IMX296 camera. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called imx296. |
| |
| config VIDEO_IMX319 |
| tristate "Sony IMX319 sensor support" |
| help |
| This is a Video4Linux2 sensor driver for the Sony |
| IMX319 camera. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called imx319. |
| |
| config VIDEO_IMX334 |
| tristate "Sony IMX334 sensor support" |
| depends on OF_GPIO |
| help |
| This is a Video4Linux2 sensor driver for the Sony |
| IMX334 camera. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called imx334. |
| |
| config VIDEO_IMX335 |
| tristate "Sony IMX335 sensor support" |
| depends on OF_GPIO |
| help |
| This is a Video4Linux2 sensor driver for the Sony |
| IMX335 camera. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called imx335. |
| |
| config VIDEO_IMX355 |
| tristate "Sony IMX355 sensor support" |
| help |
| This is a Video4Linux2 sensor driver for the Sony |
| IMX355 camera. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called imx355. |
| |
| config VIDEO_IMX412 |
| tristate "Sony IMX412 sensor support" |
| depends on OF_GPIO |
| help |
| This is a Video4Linux2 sensor driver for the Sony |
| IMX412 camera. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called imx412. |
| |
| config VIDEO_IMX415 |
| tristate "Sony IMX415 sensor support" |
| depends on OF_GPIO |
| help |
| This is a Video4Linux2 sensor driver for the Sony |
| IMX415 camera. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called imx415. |
| |
| config VIDEO_MAX9271_LIB |
| tristate |
| |
| config VIDEO_MT9M001 |
| tristate "mt9m001 support" |
| help |
| This driver supports MT9M001 cameras from Micron, monochrome |
| and colour models. |
| |
| config VIDEO_MT9M111 |
| tristate "mt9m111, mt9m112 and mt9m131 support" |
| help |
| This driver supports MT9M111, MT9M112 and MT9M131 cameras from |
| Micron/Aptina |
| |
| config VIDEO_MT9M114 |
| tristate "onsemi MT9M114 sensor support" |
| select V4L2_CCI_I2C |
| help |
| This is a Video4Linux2 sensor-level driver for the onsemi MT9M114 |
| camera. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called mt9m114. |
| |
| config VIDEO_MT9P031 |
| tristate "Aptina MT9P031 support" |
| select VIDEO_APTINA_PLL |
| help |
| This is a Video4Linux2 sensor driver for the Aptina |
| (Micron) mt9p031 5 Mpixel camera. |
| |
| config VIDEO_MT9T112 |
| tristate "Aptina MT9T111/MT9T112 support" |
| help |
| This is a Video4Linux2 sensor driver for the Aptina |
| (Micron) MT9T111 and MT9T112 3 Mpixel camera. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called mt9t112. |
| |
| config VIDEO_MT9V011 |
| tristate "Micron mt9v011 sensor support" |
| help |
| This is a Video4Linux2 sensor driver for the Micron |
| mt0v011 1.3 Mpixel camera. It currently only works with the |
| em28xx driver. |
| |
| config VIDEO_MT9V032 |
| tristate "Micron MT9V032 sensor support" |
| select REGMAP_I2C |
| help |
| This is a Video4Linux2 sensor driver for the Micron |
| MT9V032 752x480 CMOS sensor. |
| |
| config VIDEO_MT9V111 |
| tristate "Aptina MT9V111 sensor support" |
| help |
| This is a Video4Linux2 sensor driver for the Aptina/Micron |
| MT9V111 sensor. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called mt9v111. |
| |
| config VIDEO_OG01A1B |
| tristate "OmniVision OG01A1B sensor support" |
| help |
| This is a Video4Linux2 sensor driver for the OmniVision |
| OG01A1B camera. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called og01a1b. |
| |
| config VIDEO_OV01A10 |
| tristate "OmniVision OV01A10 sensor support" |
| help |
| This is a Video4Linux2 sensor driver for the OmniVision |
| OV01A10 camera. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called ov01a10. |
| |
| config VIDEO_OV02A10 |
| tristate "OmniVision OV02A10 sensor support" |
| help |
| This is a Video4Linux2 sensor driver for the OmniVision |
| OV02A10 camera. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called ov02a10. |
| |
| config VIDEO_OV08D10 |
| tristate "OmniVision OV08D10 sensor support" |
| help |
| This is a Video4Linux2 sensor driver for the OmniVision |
| OV08D10 camera sensor. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called ov08d10. |
| |
| config VIDEO_OV08X40 |
| tristate "OmniVision OV08X40 sensor support" |
| help |
| This is a Video4Linux2 sensor driver for the OmniVision |
| OV08X40 camera. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called ov08x40. |
| |
| config VIDEO_OV13858 |
| tristate "OmniVision OV13858 sensor support" |
| help |
| This is a Video4Linux2 sensor driver for the OmniVision |
| OV13858 camera. |
| |
| config VIDEO_OV13B10 |
| tristate "OmniVision OV13B10 sensor support" |
| help |
| This is a Video4Linux2 sensor driver for the OmniVision |
| OV13B10 camera. |
| |
| config VIDEO_OV2640 |
| tristate "OmniVision OV2640 sensor support" |
| help |
| This is a Video4Linux2 sensor driver for the OmniVision |
| OV2640 camera. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called ov2640. |
| |
| config VIDEO_OV2659 |
| tristate "OmniVision OV2659 sensor support" |
| depends on GPIOLIB |
| help |
| This is a Video4Linux2 sensor driver for the OmniVision |
| OV2659 camera. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called ov2659. |
| |
| config VIDEO_OV2680 |
| tristate "OmniVision OV2680 sensor support" |
| select V4L2_CCI_I2C |
| help |
| This is a Video4Linux2 sensor driver for the OmniVision |
| OV2680 camera. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called ov2680. |
| |
| config VIDEO_OV2685 |
| tristate "OmniVision OV2685 sensor support" |
| help |
| This is a Video4Linux2 sensor driver for the OmniVision |
| OV2685 camera. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called ov2685. |
| |
| config VIDEO_OV2740 |
| tristate "OmniVision OV2740 sensor support" |
| depends on ACPI || COMPILE_TEST |
| select REGMAP_I2C |
| help |
| This is a Video4Linux2 sensor driver for the OmniVision |
| OV2740 camera. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called ov2740. |
| |
| config VIDEO_OV4689 |
| tristate "OmniVision OV4689 sensor support" |
| depends on GPIOLIB |
| help |
| This is a Video4Linux2 sensor-level driver for the OmniVision |
| OV4689 camera. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called ov4689. |
| |
| config VIDEO_OV5640 |
| tristate "OmniVision OV5640 sensor support" |
| depends on OF |
| depends on GPIOLIB |
| help |
| This is a Video4Linux2 sensor driver for the Omnivision |
| OV5640 camera sensor with a MIPI CSI-2 interface. |
| |
| config VIDEO_OV5645 |
| tristate "OmniVision OV5645 sensor support" |
| depends on OF |
| help |
| This is a Video4Linux2 sensor driver for the OmniVision |
| OV5645 camera. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called ov5645. |
| |
| config VIDEO_OV5647 |
| tristate "OmniVision OV5647 sensor support" |
| help |
| This is a Video4Linux2 sensor driver for the OmniVision |
| OV5647 camera. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called ov5647. |
| |
| config VIDEO_OV5648 |
| tristate "OmniVision OV5648 sensor support" |
| depends on PM |
| help |
| This is a Video4Linux2 sensor driver for the OmniVision |
| OV5648 camera. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called ov5648. |
| |
| config VIDEO_OV5670 |
| tristate "OmniVision OV5670 sensor support" |
| help |
| This is a Video4Linux2 sensor driver for the OmniVision |
| OV5670 camera. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called ov5670. |
| |
| config VIDEO_OV5675 |
| tristate "OmniVision OV5675 sensor support" |
| help |
| This is a Video4Linux2 sensor driver for the OmniVision |
| OV5675 camera. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called ov5675. |
| |
| config VIDEO_OV5693 |
| tristate "OmniVision OV5693 sensor support" |
| select V4L2_CCI_I2C |
| help |
| This is a Video4Linux2 sensor driver for the OmniVision |
| OV5693 camera. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called ov5693. |
| |
| config VIDEO_OV5695 |
| tristate "OmniVision OV5695 sensor support" |
| help |
| This is a Video4Linux2 sensor driver for the OmniVision |
| OV5695 camera. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called ov5695. |
| |
| config VIDEO_OV6650 |
| tristate "OmniVision OV6650 sensor support" |
| help |
| This is a Video4Linux2 sensor driver for the OmniVision |
| OV6650 camera. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called ov6650. |
| |
| config VIDEO_OV7251 |
| tristate "OmniVision OV7251 sensor support" |
| help |
| This is a Video4Linux2 sensor driver for the OmniVision |
| OV7251 camera. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called ov7251. |
| |
| config VIDEO_OV7640 |
| tristate "OmniVision OV7640 sensor support" |
| help |
| This is a Video4Linux2 sensor driver for the OmniVision |
| OV7640 camera. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called ov7640. |
| |
| config VIDEO_OV7670 |
| tristate "OmniVision OV7670 sensor support" |
| help |
| This is a Video4Linux2 sensor driver for the OmniVision |
| OV7670 VGA camera. It currently only works with the M88ALP01 |
| controller. |
| |
| config VIDEO_OV772X |
| tristate "OmniVision OV772x sensor support" |
| select REGMAP_SCCB |
| help |
| This is a Video4Linux2 sensor driver for the OmniVision |
| OV772x camera. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called ov772x. |
| |
| config VIDEO_OV7740 |
| tristate "OmniVision OV7740 sensor support" |
| select REGMAP_SCCB |
| help |
| This is a Video4Linux2 sensor driver for the OmniVision |
| OV7740 VGA camera sensor. |
| |
| config VIDEO_OV8856 |
| tristate "OmniVision OV8856 sensor support" |
| help |
| This is a Video4Linux2 sensor driver for the OmniVision |
| OV8856 camera sensor. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called ov8856. |
| |
| config VIDEO_OV8858 |
| tristate "OmniVision OV8858 sensor support" |
| depends on PM |
| help |
| This is a Video4Linux2 sensor driver for OmniVision |
| OV8858 camera sensor. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called ov8858. |
| |
| config VIDEO_OV8865 |
| tristate "OmniVision OV8865 sensor support" |
| depends on PM |
| help |
| This is a Video4Linux2 sensor driver for OmniVision |
| OV8865 camera sensor. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called ov8865. |
| |
| config VIDEO_OV9282 |
| tristate "OmniVision OV9282 sensor support" |
| depends on OF_GPIO |
| help |
| This is a Video4Linux2 sensor driver for the OmniVision |
| OV9282 camera sensor. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called ov9282. |
| |
| config VIDEO_OV9640 |
| tristate "OmniVision OV9640 sensor support" |
| help |
| This is a Video4Linux2 sensor driver for the OmniVision |
| OV9640 camera sensor. |
| |
| config VIDEO_OV9650 |
| tristate "OmniVision OV9650/OV9652 sensor support" |
| select REGMAP_SCCB |
| help |
| This is a V4L2 sensor driver for the Omnivision |
| OV9650 and OV9652 camera sensors. |
| |
| config VIDEO_OV9734 |
| tristate "OmniVision OV9734 sensor support" |
| depends on ACPI || COMPILE_TEST |
| help |
| This is a Video4Linux2 sensor driver for the OmniVision |
| OV9734 camera. |
| |
| To compile this driver as a module, choose M here: the |
| module's name is ov9734. |
| |
| config VIDEO_RDACM20 |
| tristate "IMI RDACM20 camera support" |
| select VIDEO_MAX9271_LIB |
| help |
| This driver supports the IMI RDACM20 GMSL camera, used in |
| ADAS systems. |
| |
| This camera should be used in conjunction with a GMSL |
| deserialiser such as the MAX9286. |
| |
| config VIDEO_RDACM21 |
| tristate "IMI RDACM21 camera support" |
| select VIDEO_MAX9271_LIB |
| help |
| This driver supports the IMI RDACM21 GMSL camera, used in |
| ADAS systems. |
| |
| This camera should be used in conjunction with a GMSL |
| deserialiser such as the MAX9286. |
| |
| config VIDEO_RJ54N1 |
| tristate "Sharp RJ54N1CB0C sensor support" |
| help |
| This is a V4L2 sensor driver for Sharp RJ54N1CB0C CMOS image |
| sensor. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called rj54n1. |
| |
| config VIDEO_S5C73M3 |
| tristate "Samsung S5C73M3 sensor support" |
| depends on SPI |
| help |
| This is a V4L2 sensor driver for Samsung S5C73M3 |
| 8 Mpixel camera. |
| |
| config VIDEO_S5K5BAF |
| tristate "Samsung S5K5BAF sensor support" |
| help |
| This is a V4L2 sensor driver for Samsung S5K5BAF 2M |
| camera sensor with an embedded SoC image signal processor. |
| |
| config VIDEO_S5K6A3 |
| tristate "Samsung S5K6A3 sensor support" |
| help |
| This is a V4L2 sensor driver for Samsung S5K6A3 raw |
| camera sensor. |
| |
| config VIDEO_ST_VGXY61 |
| tristate "ST VGXY61 sensor support" |
| depends on OF && GPIOLIB |
| help |
| This is a Video4Linux2 sensor driver for the ST VGXY61 |
| camera sensor. |
| |
| source "drivers/media/i2c/ccs/Kconfig" |
| source "drivers/media/i2c/et8ek8/Kconfig" |
| |
| endif |
| |
| menu "Lens drivers" |
| visible if MEDIA_CAMERA_SUPPORT |
| |
| config VIDEO_AD5820 |
| tristate "AD5820 lens voice coil support" |
| depends on GPIOLIB && I2C && VIDEO_DEV |
| select MEDIA_CONTROLLER |
| select V4L2_ASYNC |
| help |
| This is a driver for the AD5820 camera lens voice coil. |
| It is used for example in Nokia N900 (RX-51). |
| |
| config VIDEO_AK7375 |
| tristate "AK7375 lens voice coil support" |
| depends on I2C && VIDEO_DEV |
| select MEDIA_CONTROLLER |
| select VIDEO_V4L2_SUBDEV_API |
| select V4L2_ASYNC |
| help |
| This is a driver for the AK7375 camera lens voice coil. |
| AK7375 is a 12 bit DAC with 120mA output current sink |
| capability. This is designed for linear control of |
| voice coil motors, controlled via I2C serial interface. |
| |
| config VIDEO_DW9714 |
| tristate "DW9714 lens voice coil support" |
| depends on I2C && VIDEO_DEV |
| select MEDIA_CONTROLLER |
| select VIDEO_V4L2_SUBDEV_API |
| select V4L2_ASYNC |
| help |
| This is a driver for the DW9714 camera lens voice coil. |
| DW9714 is a 10 bit DAC with 120mA output current sink |
| capability. This is designed for linear control of |
| voice coil motors, controlled via I2C serial interface. |
| |
| config VIDEO_DW9719 |
| tristate "DW9719 lens voice coil support" |
| depends on I2C && VIDEO_DEV |
| select MEDIA_CONTROLLER |
| select VIDEO_V4L2_SUBDEV_API |
| select V4L2_ASYNC |
| select V4L2_CCI_I2C |
| help |
| This is a driver for the DW9719 camera lens voice coil. |
| This is designed for linear control of voice coil motors, |
| controlled via I2C serial interface. |
| |
| config VIDEO_DW9768 |
| tristate "DW9768 lens voice coil support" |
| depends on I2C && VIDEO_DEV |
| select MEDIA_CONTROLLER |
| select VIDEO_V4L2_SUBDEV_API |
| select V4L2_FWNODE |
| help |
| This is a driver for the DW9768 camera lens voice coil. |
| DW9768 is a 10 bit DAC with 100mA output current sink |
| capability. This is designed for linear control of |
| voice coil motors, controlled via I2C serial interface. |
| |
| config VIDEO_DW9807_VCM |
| tristate "DW9807 lens voice coil support" |
| depends on I2C && VIDEO_DEV |
| select MEDIA_CONTROLLER |
| select VIDEO_V4L2_SUBDEV_API |
| select V4L2_ASYNC |
| help |
| This is a driver for the DW9807 camera lens voice coil. |
| DW9807 is a 10 bit DAC with 100mA output current sink |
| capability. This is designed for linear control of |
| voice coil motors, controlled via I2C serial interface. |
| |
| endmenu |
| |
| menu "Flash devices" |
| visible if MEDIA_CAMERA_SUPPORT |
| |
| config VIDEO_ADP1653 |
| tristate "ADP1653 flash support" |
| depends on I2C && VIDEO_DEV |
| select MEDIA_CONTROLLER |
| select V4L2_ASYNC |
| help |
| This is a driver for the ADP1653 flash controller. It is used for |
| example in Nokia N900. |
| |
| config VIDEO_LM3560 |
| tristate "LM3560 dual flash driver support" |
| depends on I2C && VIDEO_DEV |
| select MEDIA_CONTROLLER |
| select REGMAP_I2C |
| select V4L2_ASYNC |
| help |
| This is a driver for the lm3560 dual flash controllers. It controls |
| flash, torch LEDs. |
| |
| config VIDEO_LM3646 |
| tristate "LM3646 dual flash driver support" |
| depends on I2C && VIDEO_DEV |
| select MEDIA_CONTROLLER |
| select REGMAP_I2C |
| select V4L2_ASYNC |
| help |
| This is a driver for the lm3646 dual flash controllers. It controls |
| flash, torch LEDs. |
| |
| endmenu |
| |
| # |
| # V4L2 I2C drivers that aren't related with Camera support |
| # |
| |
| comment "audio, video and radio I2C drivers auto-selected by 'Autoselect ancillary drivers'" |
| depends on MEDIA_HIDE_ANCILLARY_SUBDRV |
| # |
| # Encoder / Decoder module configuration |
| # |
| |
| menu "Audio decoders, processors and mixers" |
| visible if !MEDIA_HIDE_ANCILLARY_SUBDRV |
| |
| config VIDEO_CS3308 |
| tristate "Cirrus Logic CS3308 audio ADC" |
| depends on VIDEO_DEV && I2C |
| help |
| Support for the Cirrus Logic CS3308 High Performance 8-Channel |
| Analog Volume Control |
| |
| To compile this driver as a module, choose M here: the |
| module will be called cs3308. |
| |
| config VIDEO_CS5345 |
| tristate "Cirrus Logic CS5345 audio ADC" |
| depends on VIDEO_DEV && I2C |
| help |
| Support for the Cirrus Logic CS5345 24-bit, 192 kHz |
| stereo A/D converter. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called cs5345. |
| |
| config VIDEO_CS53L32A |
| tristate "Cirrus Logic CS53L32A audio ADC" |
| depends on VIDEO_DEV && I2C |
| help |
| Support for the Cirrus Logic CS53L32A low voltage |
| stereo A/D converter. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called cs53l32a. |
| |
| config VIDEO_MSP3400 |
| tristate "Micronas MSP34xx audio decoders" |
| depends on VIDEO_DEV && I2C |
| help |
| Support for the Micronas MSP34xx series of audio decoders. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called msp3400. |
| |
| config VIDEO_SONY_BTF_MPX |
| tristate "Sony BTF's internal MPX" |
| depends on VIDEO_DEV && I2C |
| help |
| Support for the internal MPX of the Sony BTF-PG472Z tuner. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called sony-btf-mpx. |
| |
| config VIDEO_TDA1997X |
| tristate "NXP TDA1997x HDMI receiver" |
| depends on VIDEO_DEV && I2C |
| depends on SND_SOC |
| select HDMI |
| select SND_PCM |
| select V4L2_FWNODE |
| select MEDIA_CONTROLLER |
| select VIDEO_V4L2_SUBDEV_API |
| help |
| V4L2 subdevice driver for the NXP TDA1997x HDMI receivers. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called tda1997x. |
| |
| config VIDEO_TDA7432 |
| tristate "Philips TDA7432 audio processor" |
| depends on VIDEO_DEV && I2C |
| help |
| Support for tda7432 audio decoder chip found on some bt8xx boards. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called tda7432. |
| |
| config VIDEO_TDA9840 |
| tristate "Philips TDA9840 audio processor" |
| depends on I2C |
| help |
| Support for tda9840 audio decoder chip found on some Zoran boards. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called tda9840. |
| |
| config VIDEO_TEA6415C |
| tristate "Philips TEA6415C audio processor" |
| depends on I2C |
| help |
| Support for tea6415c audio decoder chip found on some bt8xx boards. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called tea6415c. |
| |
| config VIDEO_TEA6420 |
| tristate "Philips TEA6420 audio processor" |
| depends on I2C |
| help |
| Support for tea6420 audio decoder chip found on some bt8xx boards. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called tea6420. |
| |
| config VIDEO_TLV320AIC23B |
| tristate "Texas Instruments TLV320AIC23B audio codec" |
| depends on VIDEO_DEV && I2C |
| help |
| Support for the Texas Instruments TLV320AIC23B audio codec. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called tlv320aic23b. |
| |
| config VIDEO_TVAUDIO |
| tristate "Simple audio decoder chips" |
| depends on VIDEO_DEV && I2C |
| help |
| Support for several audio decoder chips found on some bt8xx boards: |
| Philips: tda9840, tda9873h, tda9874h/a, tda9850, tda985x, tea6300, |
| tea6320, tea6420, tda8425, ta8874z. |
| Microchip: pic16c54 based design on ProVideo PV951 board. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called tvaudio. |
| |
| config VIDEO_UDA1342 |
| tristate "Philips UDA1342 audio codec" |
| depends on VIDEO_DEV && I2C |
| help |
| Support for the Philips UDA1342 audio codec. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called uda1342. |
| |
| config VIDEO_VP27SMPX |
| tristate "Panasonic VP27's internal MPX" |
| depends on VIDEO_DEV && I2C |
| help |
| Support for the internal MPX of the Panasonic VP27s tuner. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called vp27smpx. |
| |
| config VIDEO_WM8739 |
| tristate "Wolfson Microelectronics WM8739 stereo audio ADC" |
| depends on VIDEO_DEV && I2C |
| help |
| Support for the Wolfson Microelectronics WM8739 |
| stereo A/D Converter. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called wm8739. |
| |
| config VIDEO_WM8775 |
| tristate "Wolfson Microelectronics WM8775 audio ADC with input mixer" |
| depends on VIDEO_DEV && I2C |
| help |
| Support for the Wolfson Microelectronics WM8775 high |
| performance stereo A/D Converter with a 4 channel input mixer. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called wm8775. |
| |
| endmenu |
| |
| menu "RDS decoders" |
| visible if !MEDIA_HIDE_ANCILLARY_SUBDRV |
| |
| config VIDEO_SAA6588 |
| tristate "SAA6588 Radio Chip RDS decoder support" |
| depends on VIDEO_DEV && I2C |
| |
| help |
| Support for this Radio Data System (RDS) decoder. This allows |
| seeing radio station identification transmitted using this |
| standard. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called saa6588. |
| |
| endmenu |
| |
| menu "Video decoders" |
| visible if !MEDIA_HIDE_ANCILLARY_SUBDRV |
| |
| config VIDEO_ADV7180 |
| tristate "Analog Devices ADV7180 decoder" |
| depends on GPIOLIB && VIDEO_DEV && I2C |
| select MEDIA_CONTROLLER |
| select VIDEO_V4L2_SUBDEV_API |
| select V4L2_ASYNC |
| help |
| Support for the Analog Devices ADV7180 video decoder. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called adv7180. |
| |
| config VIDEO_ADV7183 |
| tristate "Analog Devices ADV7183 decoder" |
| depends on VIDEO_DEV && I2C |
| help |
| V4l2 subdevice driver for the Analog Devices |
| ADV7183 video decoder. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called adv7183. |
| |
| config VIDEO_ADV748X |
| tristate "Analog Devices ADV748x decoder" |
| depends on VIDEO_DEV && I2C |
| depends on OF |
| select MEDIA_CONTROLLER |
| select VIDEO_V4L2_SUBDEV_API |
| select REGMAP_I2C |
| select V4L2_FWNODE |
| help |
| V4L2 subdevice driver for the Analog Devices |
| ADV7481 and ADV7482 HDMI/Analog video decoders. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called adv748x. |
| |
| config VIDEO_ADV7604 |
| tristate "Analog Devices ADV7604 decoder" |
| depends on VIDEO_DEV && I2C |
| depends on GPIOLIB || COMPILE_TEST |
| select MEDIA_CONTROLLER |
| select VIDEO_V4L2_SUBDEV_API |
| select REGMAP_I2C |
| select HDMI |
| select V4L2_FWNODE |
| help |
| Support for the Analog Devices ADV7604 video decoder. |
| |
| This is a Analog Devices Component/Graphics Digitizer |
| with 4:1 Multiplexed HDMI Receiver. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called adv7604. |
| |
| config VIDEO_ADV7604_CEC |
| bool "Enable Analog Devices ADV7604 CEC support" |
| depends on VIDEO_ADV7604 |
| select CEC_CORE |
| help |
| When selected the adv7604 will support the optional |
| HDMI CEC feature. |
| |
| config VIDEO_ADV7842 |
| tristate "Analog Devices ADV7842 decoder" |
| depends on VIDEO_DEV && I2C |
| select MEDIA_CONTROLLER |
| select VIDEO_V4L2_SUBDEV_API |
| select HDMI |
| help |
| Support for the Analog Devices ADV7842 video decoder. |
| |
| This is a Analog Devices Component/Graphics/SD Digitizer |
| with 2:1 Multiplexed HDMI Receiver. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called adv7842. |
| |
| config VIDEO_ADV7842_CEC |
| bool "Enable Analog Devices ADV7842 CEC support" |
| depends on VIDEO_ADV7842 |
| select CEC_CORE |
| help |
| When selected the adv7842 will support the optional |
| HDMI CEC feature. |
| |
| config VIDEO_BT819 |
| tristate "BT819A VideoStream decoder" |
| depends on VIDEO_DEV && I2C |
| help |
| Support for BT819A video decoder. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called bt819. |
| |
| config VIDEO_BT856 |
| tristate "BT856 VideoStream decoder" |
| depends on VIDEO_DEV && I2C |
| help |
| Support for BT856 video decoder. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called bt856. |
| |
| config VIDEO_BT866 |
| tristate "BT866 VideoStream decoder" |
| depends on VIDEO_DEV && I2C |
| help |
| Support for BT866 video decoder. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called bt866. |
| |
| config VIDEO_ISL7998X |
| tristate "Intersil ISL7998x video decoder" |
| depends on VIDEO_DEV && I2C |
| depends on OF_GPIO |
| select MEDIA_CONTROLLER |
| select VIDEO_V4L2_SUBDEV_API |
| select V4L2_FWNODE |
| help |
| Support for Intersil ISL7998x analog to MIPI-CSI2 or |
| BT.656 decoder. |
| |
| config VIDEO_KS0127 |
| tristate "KS0127 video decoder" |
| depends on VIDEO_DEV && I2C |
| help |
| Support for KS0127 video decoder. |
| |
| This chip is used on AverMedia AVS6EYES Zoran-based MJPEG |
| cards. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called ks0127. |
| |
| config VIDEO_MAX9286 |
| tristate "Maxim MAX9286 GMSL deserializer support" |
| depends on I2C && I2C_MUX |
| depends on VIDEO_DEV |
| depends on OF_GPIO |
| select V4L2_FWNODE |
| select VIDEO_V4L2_SUBDEV_API |
| select MEDIA_CONTROLLER |
| help |
| This driver supports the Maxim MAX9286 GMSL deserializer. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called max9286. |
| |
| config VIDEO_ML86V7667 |
| tristate "OKI ML86V7667 video decoder" |
| depends on VIDEO_DEV && I2C |
| help |
| Support for the OKI Semiconductor ML86V7667 video decoder. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called ml86v7667. |
| |
| config VIDEO_SAA7110 |
| tristate "Philips SAA7110 video decoder" |
| depends on VIDEO_DEV && I2C |
| help |
| Support for the Philips SAA7110 video decoders. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called saa7110. |
| |
| config VIDEO_SAA711X |
| tristate "Philips SAA7111/3/4/5 video decoders" |
| depends on VIDEO_DEV && I2C |
| help |
| Support for the Philips SAA7111/3/4/5 video decoders. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called saa7115. |
| |
| config VIDEO_TC358743 |
| tristate "Toshiba TC358743 decoder" |
| depends on VIDEO_DEV && I2C |
| select MEDIA_CONTROLLER |
| select VIDEO_V4L2_SUBDEV_API |
| select HDMI |
| select V4L2_FWNODE |
| help |
| Support for the Toshiba TC358743 HDMI to MIPI CSI-2 bridge. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called tc358743. |
| |
| config VIDEO_TC358743_CEC |
| bool "Enable Toshiba TC358743 CEC support" |
| depends on VIDEO_TC358743 |
| select CEC_CORE |
| help |
| When selected the tc358743 will support the optional |
| HDMI CEC feature. |
| |
| config VIDEO_TC358746 |
| tristate "Toshiba TC358746 parallel-CSI2 bridge" |
| depends on VIDEO_DEV && PM && I2C |
| select VIDEO_V4L2_SUBDEV_API |
| select MEDIA_CONTROLLER |
| select V4L2_FWNODE |
| select GENERIC_PHY |
| select GENERIC_PHY_MIPI_DPHY |
| select REGMAP_I2C |
| help |
| Support for the Toshiba TC358746 parallel to MIPI CSI-2 bridge. |
| The bridge can work in both directions but currently only the |
| parallel-in / csi-out path is supported. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called tc358746. |
| |
| config VIDEO_TVP514X |
| tristate "Texas Instruments TVP514x video decoder" |
| depends on VIDEO_DEV && I2C |
| select V4L2_FWNODE |
| help |
| This is a Video4Linux2 sensor driver for the TI TVP5146/47 |
| decoder. It is currently working with the TI OMAP3 camera |
| controller. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called tvp514x. |
| |
| config VIDEO_TVP5150 |
| tristate "Texas Instruments TVP5150 video decoder" |
| depends on VIDEO_DEV && I2C |
| select V4L2_FWNODE |
| select REGMAP_I2C |
| help |
| Support for the Texas Instruments TVP5150 video decoder. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called tvp5150. |
| |
| config VIDEO_TVP7002 |
| tristate "Texas Instruments TVP7002 video decoder" |
| depends on VIDEO_DEV && I2C |
| select V4L2_FWNODE |
| help |
| Support for the Texas Instruments TVP7002 video decoder. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called tvp7002. |
| |
| config VIDEO_TW2804 |
| tristate "Techwell TW2804 multiple video decoder" |
| depends on VIDEO_DEV && I2C |
| help |
| Support for the Techwell tw2804 multiple video decoder. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called tw2804. |
| |
| config VIDEO_TW9903 |
| tristate "Techwell TW9903 video decoder" |
| depends on VIDEO_DEV && I2C |
| help |
| Support for the Techwell tw9903 multi-standard video decoder |
| with high quality down scaler. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called tw9903. |
| |
| config VIDEO_TW9906 |
| tristate "Techwell TW9906 video decoder" |
| depends on VIDEO_DEV && I2C |
| help |
| Support for the Techwell tw9906 enhanced multi-standard comb filter |
| video decoder with YCbCr input support. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called tw9906. |
| |
| config VIDEO_TW9910 |
| tristate "Techwell TW9910 video decoder" |
| depends on VIDEO_DEV && I2C |
| select V4L2_ASYNC |
| help |
| Support for Techwell TW9910 NTSC/PAL/SECAM video decoder. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called tw9910. |
| |
| config VIDEO_VPX3220 |
| tristate "vpx3220a, vpx3216b & vpx3214c video decoders" |
| depends on VIDEO_DEV && I2C |
| help |
| Support for VPX322x video decoders. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called vpx3220. |
| |
| comment "Video and audio decoders" |
| |
| config VIDEO_SAA717X |
| tristate "Philips SAA7171/3/4 audio/video decoders" |
| depends on VIDEO_DEV && I2C |
| help |
| Support for the Philips SAA7171/3/4 audio/video decoders. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called saa717x. |
| |
| source "drivers/media/i2c/cx25840/Kconfig" |
| |
| endmenu |
| |
| menu "Video encoders" |
| visible if !MEDIA_HIDE_ANCILLARY_SUBDRV |
| |
| config VIDEO_ADV7170 |
| tristate "Analog Devices ADV7170 video encoder" |
| depends on VIDEO_DEV && I2C |
| help |
| Support for the Analog Devices ADV7170 video encoder driver |
| |
| To compile this driver as a module, choose M here: the |
| module will be called adv7170. |
| |
| config VIDEO_ADV7175 |
| tristate "Analog Devices ADV7175 video encoder" |
| depends on VIDEO_DEV && I2C |
| help |
| Support for the Analog Devices ADV7175 video encoder driver |
| |
| To compile this driver as a module, choose M here: the |
| module will be called adv7175. |
| |
| config VIDEO_ADV7343 |
| tristate "ADV7343 video encoder" |
| depends on I2C |
| select V4L2_ASYNC |
| help |
| Support for Analog Devices I2C bus based ADV7343 encoder. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called adv7343. |
| |
| config VIDEO_ADV7393 |
| tristate "ADV7393 video encoder" |
| depends on I2C |
| help |
| Support for Analog Devices I2C bus based ADV7393 encoder. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called adv7393. |
| |
| config VIDEO_ADV7511 |
| tristate "Analog Devices ADV7511 encoder" |
| depends on VIDEO_DEV && I2C |
| depends on DRM_I2C_ADV7511=n || COMPILE_TEST |
| select MEDIA_CONTROLLER |
| select VIDEO_V4L2_SUBDEV_API |
| select HDMI |
| help |
| Support for the Analog Devices ADV7511 video encoder. |
| |
| This is a Analog Devices HDMI transmitter. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called adv7511. |
| |
| config VIDEO_ADV7511_CEC |
| bool "Enable Analog Devices ADV7511 CEC support" |
| depends on VIDEO_ADV7511 |
| select CEC_CORE |
| help |
| When selected the adv7511 will support the optional |
| HDMI CEC feature. |
| |
| config VIDEO_AK881X |
| tristate "AK8813/AK8814 video encoders" |
| depends on I2C |
| help |
| Video output driver for AKM AK8813 and AK8814 TV encoders |
| |
| config VIDEO_SAA7127 |
| tristate "Philips SAA7127/9 digital video encoders" |
| depends on VIDEO_DEV && I2C |
| help |
| Support for the Philips SAA7127/9 digital video encoders. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called saa7127. |
| |
| config VIDEO_SAA7185 |
| tristate "Philips SAA7185 video encoder" |
| depends on VIDEO_DEV && I2C |
| help |
| Support for the Philips SAA7185 video encoder. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called saa7185. |
| |
| config VIDEO_THS8200 |
| tristate "Texas Instruments THS8200 video encoder" |
| depends on VIDEO_DEV && I2C |
| select V4L2_ASYNC |
| help |
| Support for the Texas Instruments THS8200 video encoder. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called ths8200. |
| |
| endmenu |
| |
| menu "Video improvement chips" |
| visible if !MEDIA_HIDE_ANCILLARY_SUBDRV |
| |
| config VIDEO_UPD64031A |
| tristate "NEC Electronics uPD64031A Ghost Reduction" |
| depends on VIDEO_DEV && I2C |
| select V4L2_ASYNC |
| help |
| Support for the NEC Electronics uPD64031A Ghost Reduction |
| video chip. It is most often found in NTSC TV cards made for |
| Japan and is used to reduce the 'ghosting' effect that can |
| be present in analog TV broadcasts. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called upd64031a. |
| |
| config VIDEO_UPD64083 |
| tristate "NEC Electronics uPD64083 3-Dimensional Y/C separation" |
| depends on VIDEO_DEV && I2C |
| help |
| Support for the NEC Electronics uPD64083 3-Dimensional Y/C |
| separation video chip. It is used to improve the quality of |
| the colors of a composite signal. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called upd64083. |
| |
| endmenu |
| |
| menu "Audio/Video compression chips" |
| visible if !MEDIA_HIDE_ANCILLARY_SUBDRV |
| |
| config VIDEO_SAA6752HS |
| tristate "Philips SAA6752HS MPEG-2 Audio/Video Encoder" |
| depends on VIDEO_DEV && I2C |
| select CRC32 |
| help |
| Support for the Philips SAA6752HS MPEG-2 video and MPEG-audio/AC-3 |
| audio encoder with multiplexer. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called saa6752hs. |
| |
| endmenu |
| |
| menu "SDR tuner chips" |
| visible if !MEDIA_HIDE_ANCILLARY_SUBDRV |
| |
| config SDR_MAX2175 |
| tristate "Maxim 2175 RF to Bits tuner" |
| depends on VIDEO_DEV && MEDIA_SDR_SUPPORT && I2C |
| select REGMAP_I2C |
| select V4L2_ASYNC |
| help |
| Support for Maxim 2175 tuner. It is an advanced analog/digital |
| radio receiver with RF-to-Bits front-end designed for SDR solutions. |
| |
| To compile this driver as a module, choose M here; the |
| module will be called max2175. |
| |
| endmenu |
| |
| menu "Miscellaneous helper chips" |
| visible if !MEDIA_HIDE_ANCILLARY_SUBDRV |
| |
| config VIDEO_I2C |
| tristate "I2C transport video support" |
| depends on VIDEO_DEV && I2C |
| select VIDEOBUF2_VMALLOC |
| imply HWMON |
| help |
| Enable the I2C transport video support which supports the |
| following: |
| * Panasonic AMG88xx Grid-Eye Sensors |
| * Melexis MLX90640 Thermal Cameras |
| |
| To compile this driver as a module, choose M here: the |
| module will be called video-i2c |
| |
| config VIDEO_M52790 |
| tristate "Mitsubishi M52790 A/V switch" |
| depends on VIDEO_DEV && I2C |
| help |
| Support for the Mitsubishi M52790 A/V switch. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called m52790. |
| |
| config VIDEO_ST_MIPID02 |
| tristate "STMicroelectronics MIPID02 CSI-2 to PARALLEL bridge" |
| depends on I2C && VIDEO_DEV |
| select MEDIA_CONTROLLER |
| select VIDEO_V4L2_SUBDEV_API |
| select V4L2_FWNODE |
| help |
| Support for STMicroelectronics MIPID02 CSI-2 to PARALLEL bridge. |
| It is used to allow usage of CSI-2 sensor with PARALLEL port |
| controller. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called st-mipid02. |
| |
| config VIDEO_THS7303 |
| tristate "THS7303/53 Video Amplifier" |
| depends on VIDEO_DEV && I2C |
| select V4L2_ASYNC |
| help |
| Support for TI THS7303/53 video amplifier |
| |
| To compile this driver as a module, choose M here: the |
| module will be called ths7303. |
| |
| endmenu |
| |
| # |
| # Video serializers and deserializers (e.g. FPD-Link) |
| # |
| |
| menu "Video serializers and deserializers" |
| |
| config VIDEO_DS90UB913 |
| tristate "TI DS90UB913 FPD-Link III Serializer" |
| depends on OF && I2C && VIDEO_DEV && COMMON_CLK |
| select I2C_ATR |
| select MEDIA_CONTROLLER |
| select GPIOLIB |
| select REGMAP_I2C |
| select V4L2_FWNODE |
| select VIDEO_V4L2_SUBDEV_API |
| help |
| Device driver for the Texas Instruments DS90UB913 |
| FPD-Link III Serializer. |
| |
| config VIDEO_DS90UB953 |
| tristate "TI FPD-Link III/IV CSI-2 Serializers" |
| depends on OF && I2C && VIDEO_DEV && COMMON_CLK |
| select I2C_ATR |
| select MEDIA_CONTROLLER |
| select GPIOLIB |
| select REGMAP_I2C |
| select V4L2_FWNODE |
| select VIDEO_V4L2_SUBDEV_API |
| help |
| Device driver for the Texas Instruments DS90UB953 |
| FPD-Link III Serializer and DS90UB971 FPD-Link IV Serializer. |
| |
| config VIDEO_DS90UB960 |
| tristate "TI FPD-Link III/IV Deserializers" |
| depends on OF && I2C && VIDEO_DEV && COMMON_CLK |
| select I2C_ATR |
| select MEDIA_CONTROLLER |
| select GPIOLIB |
| select REGMAP_I2C |
| select V4L2_FWNODE |
| select VIDEO_V4L2_SUBDEV_API |
| help |
| Device driver for the Texas Instruments DS90UB960 |
| FPD-Link III Deserializer and DS90UB9702 FPD-Link IV Deserializer. |
| |
| endmenu |
| |
| endif # VIDEO_DEV |
