| // SPDX-License-Identifier: GPL-2.0 |
| // |
| // Copyright (C) 2017-2018 Socionext Inc. |
| // Author: Masahiro Yamada <yamada.masahiro@socionext.com> |
| |
| #include <linux/bitfield.h> |
| #include <linux/bitops.h> |
| #include <linux/clk.h> |
| #include <linux/delay.h> |
| #include <linux/dma-mapping.h> |
| #include <linux/mfd/syscon.h> |
| #include <linux/mfd/tmio.h> |
| #include <linux/mmc/host.h> |
| #include <linux/module.h> |
| #include <linux/of.h> |
| #include <linux/pinctrl/consumer.h> |
| #include <linux/platform_device.h> |
| #include <linux/regmap.h> |
| #include <linux/reset.h> |
| |
| #include "tmio_mmc.h" |
| |
| #define UNIPHIER_SD_CLK_CTL_DIV1024 BIT(16) |
| #define UNIPHIER_SD_CLK_CTL_DIV1 BIT(10) |
| #define UNIPHIER_SD_CLKCTL_OFFEN BIT(9) // auto SDCLK stop |
| #define UNIPHIER_SD_CC_EXT_MODE 0x1b0 |
| #define UNIPHIER_SD_CC_EXT_MODE_DMA BIT(1) |
| #define UNIPHIER_SD_HOST_MODE 0x1c8 |
| #define UNIPHIER_SD_VOLT 0x1e4 |
| #define UNIPHIER_SD_VOLT_MASK GENMASK(1, 0) |
| #define UNIPHIER_SD_VOLT_OFF 0 |
| #define UNIPHIER_SD_VOLT_330 1 // 3.3V signal |
| #define UNIPHIER_SD_VOLT_180 2 // 1.8V signal |
| #define UNIPHIER_SD_DMA_MODE 0x410 |
| #define UNIPHIER_SD_DMA_MODE_DIR_MASK GENMASK(17, 16) |
| #define UNIPHIER_SD_DMA_MODE_DIR_TO_DEV 0 |
| #define UNIPHIER_SD_DMA_MODE_DIR_FROM_DEV 1 |
| #define UNIPHIER_SD_DMA_MODE_WIDTH_MASK GENMASK(5, 4) |
| #define UNIPHIER_SD_DMA_MODE_WIDTH_8 0 |
| #define UNIPHIER_SD_DMA_MODE_WIDTH_16 1 |
| #define UNIPHIER_SD_DMA_MODE_WIDTH_32 2 |
| #define UNIPHIER_SD_DMA_MODE_WIDTH_64 3 |
| #define UNIPHIER_SD_DMA_MODE_ADDR_INC BIT(0) // 1: inc, 0: fixed |
| #define UNIPHIER_SD_DMA_CTL 0x414 |
| #define UNIPHIER_SD_DMA_CTL_START BIT(0) // start DMA (auto cleared) |
| #define UNIPHIER_SD_DMA_RST 0x418 |
| #define UNIPHIER_SD_DMA_RST_CH1 BIT(9) |
| #define UNIPHIER_SD_DMA_RST_CH0 BIT(8) |
| #define UNIPHIER_SD_DMA_ADDR_L 0x440 |
| #define UNIPHIER_SD_DMA_ADDR_H 0x444 |
| |
| /* SD control */ |
| #define UNIPHIER_SDCTRL_CHOFFSET 0x200 |
| #define UNIPHIER_SDCTRL_MODE 0x30 |
| #define UNIPHIER_SDCTRL_MODE_UHS1MOD BIT(15) |
| #define UNIPHIER_SDCTRL_MODE_SDRSEL BIT(14) |
| |
| /* |
| * IP is extended to support various features: built-in DMA engine, |
| * 1/1024 divisor, etc. |
| */ |
| #define UNIPHIER_SD_CAP_EXTENDED_IP BIT(0) |
| /* RX channel of the built-in DMA controller is broken (Pro5) */ |
| #define UNIPHIER_SD_CAP_BROKEN_DMA_RX BIT(1) |
| |
| struct uniphier_sd_priv { |
| struct tmio_mmc_data tmio_data; |
| struct pinctrl *pinctrl; |
| struct pinctrl_state *pinstate_uhs; |
| struct clk *clk; |
| struct reset_control *rst; |
| struct reset_control *rst_br; |
| struct reset_control *rst_hw; |
| struct dma_chan *chan; |
| enum dma_data_direction dma_dir; |
| struct regmap *sdctrl_regmap; |
| u32 sdctrl_ch; |
| unsigned long clk_rate; |
| unsigned long caps; |
| }; |
| |
| static void *uniphier_sd_priv(struct tmio_mmc_host *host) |
| { |
| return container_of(host->pdata, struct uniphier_sd_priv, tmio_data); |
| } |
| |
| static void uniphier_sd_dma_endisable(struct tmio_mmc_host *host, int enable) |
| { |
| sd_ctrl_write16(host, CTL_DMA_ENABLE, enable ? DMA_ENABLE_DMASDRW : 0); |
| } |
| |
| /* external DMA engine */ |
| static void uniphier_sd_external_dma_issue(struct tasklet_struct *t) |
| { |
| struct tmio_mmc_host *host = from_tasklet(host, t, dma_issue); |
| struct uniphier_sd_priv *priv = uniphier_sd_priv(host); |
| |
| uniphier_sd_dma_endisable(host, 1); |
| dma_async_issue_pending(priv->chan); |
| } |
| |
| static void uniphier_sd_external_dma_callback(void *param, |
| const struct dmaengine_result *result) |
| { |
| struct tmio_mmc_host *host = param; |
| struct uniphier_sd_priv *priv = uniphier_sd_priv(host); |
| unsigned long flags; |
| |
| dma_unmap_sg(mmc_dev(host->mmc), host->sg_ptr, host->sg_len, |
| priv->dma_dir); |
| |
| spin_lock_irqsave(&host->lock, flags); |
| |
| if (result->result == DMA_TRANS_NOERROR) { |
| /* |
| * When the external DMA engine is enabled, strangely enough, |
| * the DATAEND flag can be asserted even if the DMA engine has |
| * not been kicked yet. Enable the TMIO_STAT_DATAEND irq only |
| * after we make sure the DMA engine finishes the transfer, |
| * hence, in this callback. |
| */ |
| tmio_mmc_enable_mmc_irqs(host, TMIO_STAT_DATAEND); |
| } else { |
| host->data->error = -ETIMEDOUT; |
| tmio_mmc_do_data_irq(host); |
| } |
| |
| spin_unlock_irqrestore(&host->lock, flags); |
| } |
| |
| static void uniphier_sd_external_dma_start(struct tmio_mmc_host *host, |
| struct mmc_data *data) |
| { |
| struct uniphier_sd_priv *priv = uniphier_sd_priv(host); |
| enum dma_transfer_direction dma_tx_dir; |
| struct dma_async_tx_descriptor *desc; |
| dma_cookie_t cookie; |
| int sg_len; |
| |
| if (!priv->chan) |
| goto force_pio; |
| |
| if (data->flags & MMC_DATA_READ) { |
| priv->dma_dir = DMA_FROM_DEVICE; |
| dma_tx_dir = DMA_DEV_TO_MEM; |
| } else { |
| priv->dma_dir = DMA_TO_DEVICE; |
| dma_tx_dir = DMA_MEM_TO_DEV; |
| } |
| |
| sg_len = dma_map_sg(mmc_dev(host->mmc), host->sg_ptr, host->sg_len, |
| priv->dma_dir); |
| if (sg_len == 0) |
| goto force_pio; |
| |
| desc = dmaengine_prep_slave_sg(priv->chan, host->sg_ptr, sg_len, |
| dma_tx_dir, DMA_CTRL_ACK); |
| if (!desc) |
| goto unmap_sg; |
| |
| desc->callback_result = uniphier_sd_external_dma_callback; |
| desc->callback_param = host; |
| |
| cookie = dmaengine_submit(desc); |
| if (cookie < 0) |
| goto unmap_sg; |
| |
| host->dma_on = true; |
| |
| return; |
| |
| unmap_sg: |
| dma_unmap_sg(mmc_dev(host->mmc), host->sg_ptr, host->sg_len, |
| priv->dma_dir); |
| force_pio: |
| uniphier_sd_dma_endisable(host, 0); |
| } |
| |
| static void uniphier_sd_external_dma_enable(struct tmio_mmc_host *host, |
| bool enable) |
| { |
| } |
| |
| static void uniphier_sd_external_dma_request(struct tmio_mmc_host *host, |
| struct tmio_mmc_data *pdata) |
| { |
| struct uniphier_sd_priv *priv = uniphier_sd_priv(host); |
| struct dma_chan *chan; |
| |
| chan = dma_request_chan(mmc_dev(host->mmc), "rx-tx"); |
| if (IS_ERR(chan)) { |
| dev_warn(mmc_dev(host->mmc), |
| "failed to request DMA channel. falling back to PIO\n"); |
| return; /* just use PIO even for -EPROBE_DEFER */ |
| } |
| |
| /* this driver uses a single channel for both RX an TX */ |
| priv->chan = chan; |
| host->chan_rx = chan; |
| host->chan_tx = chan; |
| |
| tasklet_setup(&host->dma_issue, uniphier_sd_external_dma_issue); |
| } |
| |
| static void uniphier_sd_external_dma_release(struct tmio_mmc_host *host) |
| { |
| struct uniphier_sd_priv *priv = uniphier_sd_priv(host); |
| |
| if (priv->chan) |
| dma_release_channel(priv->chan); |
| } |
| |
| static void uniphier_sd_external_dma_abort(struct tmio_mmc_host *host) |
| { |
| struct uniphier_sd_priv *priv = uniphier_sd_priv(host); |
| |
| uniphier_sd_dma_endisable(host, 0); |
| |
| if (priv->chan) |
| dmaengine_terminate_sync(priv->chan); |
| } |
| |
| static void uniphier_sd_external_dma_dataend(struct tmio_mmc_host *host) |
| { |
| uniphier_sd_dma_endisable(host, 0); |
| |
| tmio_mmc_do_data_irq(host); |
| } |
| |
| static const struct tmio_mmc_dma_ops uniphier_sd_external_dma_ops = { |
| .start = uniphier_sd_external_dma_start, |
| .enable = uniphier_sd_external_dma_enable, |
| .request = uniphier_sd_external_dma_request, |
| .release = uniphier_sd_external_dma_release, |
| .abort = uniphier_sd_external_dma_abort, |
| .dataend = uniphier_sd_external_dma_dataend, |
| }; |
| |
| static void uniphier_sd_internal_dma_issue(struct tasklet_struct *t) |
| { |
| struct tmio_mmc_host *host = from_tasklet(host, t, dma_issue); |
| unsigned long flags; |
| |
| spin_lock_irqsave(&host->lock, flags); |
| tmio_mmc_enable_mmc_irqs(host, TMIO_STAT_DATAEND); |
| spin_unlock_irqrestore(&host->lock, flags); |
| |
| uniphier_sd_dma_endisable(host, 1); |
| writel(UNIPHIER_SD_DMA_CTL_START, host->ctl + UNIPHIER_SD_DMA_CTL); |
| } |
| |
| static void uniphier_sd_internal_dma_start(struct tmio_mmc_host *host, |
| struct mmc_data *data) |
| { |
| struct uniphier_sd_priv *priv = uniphier_sd_priv(host); |
| struct scatterlist *sg = host->sg_ptr; |
| dma_addr_t dma_addr; |
| unsigned int dma_mode_dir; |
| u32 dma_mode; |
| int sg_len; |
| |
| if ((data->flags & MMC_DATA_READ) && !host->chan_rx) |
| goto force_pio; |
| |
| if (WARN_ON(host->sg_len != 1)) |
| goto force_pio; |
| |
| if (!IS_ALIGNED(sg->offset, 8)) |
| goto force_pio; |
| |
| if (data->flags & MMC_DATA_READ) { |
| priv->dma_dir = DMA_FROM_DEVICE; |
| dma_mode_dir = UNIPHIER_SD_DMA_MODE_DIR_FROM_DEV; |
| } else { |
| priv->dma_dir = DMA_TO_DEVICE; |
| dma_mode_dir = UNIPHIER_SD_DMA_MODE_DIR_TO_DEV; |
| } |
| |
| sg_len = dma_map_sg(mmc_dev(host->mmc), sg, 1, priv->dma_dir); |
| if (sg_len == 0) |
| goto force_pio; |
| |
| dma_mode = FIELD_PREP(UNIPHIER_SD_DMA_MODE_DIR_MASK, dma_mode_dir); |
| dma_mode |= FIELD_PREP(UNIPHIER_SD_DMA_MODE_WIDTH_MASK, |
| UNIPHIER_SD_DMA_MODE_WIDTH_64); |
| dma_mode |= UNIPHIER_SD_DMA_MODE_ADDR_INC; |
| |
| writel(dma_mode, host->ctl + UNIPHIER_SD_DMA_MODE); |
| |
| dma_addr = sg_dma_address(data->sg); |
| writel(lower_32_bits(dma_addr), host->ctl + UNIPHIER_SD_DMA_ADDR_L); |
| writel(upper_32_bits(dma_addr), host->ctl + UNIPHIER_SD_DMA_ADDR_H); |
| |
| host->dma_on = true; |
| |
| return; |
| force_pio: |
| uniphier_sd_dma_endisable(host, 0); |
| } |
| |
| static void uniphier_sd_internal_dma_enable(struct tmio_mmc_host *host, |
| bool enable) |
| { |
| } |
| |
| static void uniphier_sd_internal_dma_request(struct tmio_mmc_host *host, |
| struct tmio_mmc_data *pdata) |
| { |
| struct uniphier_sd_priv *priv = uniphier_sd_priv(host); |
| |
| /* |
| * Due to a hardware bug, Pro5 cannot use DMA for RX. |
| * We can still use DMA for TX, but PIO for RX. |
| */ |
| if (!(priv->caps & UNIPHIER_SD_CAP_BROKEN_DMA_RX)) |
| host->chan_rx = (void *)0xdeadbeaf; |
| |
| host->chan_tx = (void *)0xdeadbeaf; |
| |
| tasklet_setup(&host->dma_issue, uniphier_sd_internal_dma_issue); |
| } |
| |
| static void uniphier_sd_internal_dma_release(struct tmio_mmc_host *host) |
| { |
| /* Each value is set to zero to assume "disabling" each DMA */ |
| host->chan_rx = NULL; |
| host->chan_tx = NULL; |
| } |
| |
| static void uniphier_sd_internal_dma_abort(struct tmio_mmc_host *host) |
| { |
| u32 tmp; |
| |
| uniphier_sd_dma_endisable(host, 0); |
| |
| tmp = readl(host->ctl + UNIPHIER_SD_DMA_RST); |
| tmp &= ~(UNIPHIER_SD_DMA_RST_CH1 | UNIPHIER_SD_DMA_RST_CH0); |
| writel(tmp, host->ctl + UNIPHIER_SD_DMA_RST); |
| |
| tmp |= UNIPHIER_SD_DMA_RST_CH1 | UNIPHIER_SD_DMA_RST_CH0; |
| writel(tmp, host->ctl + UNIPHIER_SD_DMA_RST); |
| } |
| |
| static void uniphier_sd_internal_dma_dataend(struct tmio_mmc_host *host) |
| { |
| struct uniphier_sd_priv *priv = uniphier_sd_priv(host); |
| |
| uniphier_sd_dma_endisable(host, 0); |
| dma_unmap_sg(mmc_dev(host->mmc), host->sg_ptr, 1, priv->dma_dir); |
| |
| tmio_mmc_do_data_irq(host); |
| } |
| |
| static const struct tmio_mmc_dma_ops uniphier_sd_internal_dma_ops = { |
| .start = uniphier_sd_internal_dma_start, |
| .enable = uniphier_sd_internal_dma_enable, |
| .request = uniphier_sd_internal_dma_request, |
| .release = uniphier_sd_internal_dma_release, |
| .abort = uniphier_sd_internal_dma_abort, |
| .dataend = uniphier_sd_internal_dma_dataend, |
| }; |
| |
| static int uniphier_sd_clk_enable(struct tmio_mmc_host *host) |
| { |
| struct uniphier_sd_priv *priv = uniphier_sd_priv(host); |
| struct mmc_host *mmc = host->mmc; |
| int ret; |
| |
| ret = clk_prepare_enable(priv->clk); |
| if (ret) |
| return ret; |
| |
| ret = clk_set_rate(priv->clk, ULONG_MAX); |
| if (ret) |
| goto disable_clk; |
| |
| priv->clk_rate = clk_get_rate(priv->clk); |
| |
| /* If max-frequency property is set, use it. */ |
| if (!mmc->f_max) |
| mmc->f_max = priv->clk_rate; |
| |
| /* |
| * 1/512 is the finest divisor in the original IP. Newer versions |
| * also supports 1/1024 divisor. (UniPhier-specific extension) |
| */ |
| if (priv->caps & UNIPHIER_SD_CAP_EXTENDED_IP) |
| mmc->f_min = priv->clk_rate / 1024; |
| else |
| mmc->f_min = priv->clk_rate / 512; |
| |
| ret = reset_control_deassert(priv->rst); |
| if (ret) |
| goto disable_clk; |
| |
| ret = reset_control_deassert(priv->rst_br); |
| if (ret) |
| goto assert_rst; |
| |
| return 0; |
| |
| assert_rst: |
| reset_control_assert(priv->rst); |
| disable_clk: |
| clk_disable_unprepare(priv->clk); |
| |
| return ret; |
| } |
| |
| static void uniphier_sd_clk_disable(struct tmio_mmc_host *host) |
| { |
| struct uniphier_sd_priv *priv = uniphier_sd_priv(host); |
| |
| reset_control_assert(priv->rst_br); |
| reset_control_assert(priv->rst); |
| clk_disable_unprepare(priv->clk); |
| } |
| |
| static void uniphier_sd_hw_reset(struct mmc_host *mmc) |
| { |
| struct tmio_mmc_host *host = mmc_priv(mmc); |
| struct uniphier_sd_priv *priv = uniphier_sd_priv(host); |
| |
| reset_control_assert(priv->rst_hw); |
| /* For eMMC, minimum is 1us but give it 9us for good measure */ |
| udelay(9); |
| reset_control_deassert(priv->rst_hw); |
| /* For eMMC, minimum is 200us but give it 300us for good measure */ |
| usleep_range(300, 1000); |
| } |
| |
| static void uniphier_sd_speed_switch(struct tmio_mmc_host *host) |
| { |
| struct uniphier_sd_priv *priv = uniphier_sd_priv(host); |
| unsigned int offset; |
| u32 val = 0; |
| |
| if (!(host->mmc->caps & MMC_CAP_UHS)) |
| return; |
| |
| if (host->mmc->ios.timing == MMC_TIMING_UHS_SDR50 || |
| host->mmc->ios.timing == MMC_TIMING_UHS_SDR104) |
| val = UNIPHIER_SDCTRL_MODE_SDRSEL; |
| |
| offset = UNIPHIER_SDCTRL_CHOFFSET * priv->sdctrl_ch |
| + UNIPHIER_SDCTRL_MODE; |
| regmap_write_bits(priv->sdctrl_regmap, offset, |
| UNIPHIER_SDCTRL_MODE_SDRSEL, val); |
| } |
| |
| static void uniphier_sd_uhs_enable(struct tmio_mmc_host *host, bool uhs_en) |
| { |
| struct uniphier_sd_priv *priv = uniphier_sd_priv(host); |
| unsigned int offset; |
| u32 val; |
| |
| if (!(host->mmc->caps & MMC_CAP_UHS)) |
| return; |
| |
| val = (uhs_en) ? UNIPHIER_SDCTRL_MODE_UHS1MOD : 0; |
| |
| offset = UNIPHIER_SDCTRL_CHOFFSET * priv->sdctrl_ch |
| + UNIPHIER_SDCTRL_MODE; |
| regmap_write_bits(priv->sdctrl_regmap, offset, |
| UNIPHIER_SDCTRL_MODE_UHS1MOD, val); |
| } |
| |
| static void uniphier_sd_set_clock(struct tmio_mmc_host *host, |
| unsigned int clock) |
| { |
| struct uniphier_sd_priv *priv = uniphier_sd_priv(host); |
| unsigned long divisor; |
| u32 tmp; |
| |
| tmp = readl(host->ctl + (CTL_SD_CARD_CLK_CTL << 1)); |
| |
| /* stop the clock before changing its rate to avoid a glitch signal */ |
| tmp &= ~CLK_CTL_SCLKEN; |
| writel(tmp, host->ctl + (CTL_SD_CARD_CLK_CTL << 1)); |
| |
| uniphier_sd_speed_switch(host); |
| |
| if (clock == 0) |
| return; |
| |
| tmp &= ~UNIPHIER_SD_CLK_CTL_DIV1024; |
| tmp &= ~UNIPHIER_SD_CLK_CTL_DIV1; |
| tmp &= ~CLK_CTL_DIV_MASK; |
| |
| divisor = priv->clk_rate / clock; |
| |
| /* |
| * In the original IP, bit[7:0] represents the divisor. |
| * bit7 set: 1/512, ... bit0 set:1/4, all bits clear: 1/2 |
| * |
| * The IP does not define a way to achieve 1/1. For UniPhier variants, |
| * bit10 is used for 1/1. Newer versions of UniPhier variants use |
| * bit16 for 1/1024. |
| */ |
| if (divisor <= 1) |
| tmp |= UNIPHIER_SD_CLK_CTL_DIV1; |
| else if (priv->caps & UNIPHIER_SD_CAP_EXTENDED_IP && divisor > 512) |
| tmp |= UNIPHIER_SD_CLK_CTL_DIV1024; |
| else |
| tmp |= roundup_pow_of_two(divisor) >> 2; |
| |
| writel(tmp, host->ctl + (CTL_SD_CARD_CLK_CTL << 1)); |
| |
| tmp |= CLK_CTL_SCLKEN; |
| writel(tmp, host->ctl + (CTL_SD_CARD_CLK_CTL << 1)); |
| } |
| |
| static void uniphier_sd_host_init(struct tmio_mmc_host *host) |
| { |
| struct uniphier_sd_priv *priv = uniphier_sd_priv(host); |
| u32 val; |
| |
| /* |
| * Connected to 32bit AXI. |
| * This register holds settings for SoC-specific internal bus |
| * connection. What is worse, the register spec was changed, |
| * breaking the backward compatibility. Write an appropriate |
| * value depending on a flag associated with a compatible string. |
| */ |
| if (priv->caps & UNIPHIER_SD_CAP_EXTENDED_IP) |
| val = 0x00000101; |
| else |
| val = 0x00000000; |
| |
| writel(val, host->ctl + UNIPHIER_SD_HOST_MODE); |
| |
| val = 0; |
| /* |
| * If supported, the controller can automatically |
| * enable/disable the clock line to the card. |
| */ |
| if (priv->caps & UNIPHIER_SD_CAP_EXTENDED_IP) |
| val |= UNIPHIER_SD_CLKCTL_OFFEN; |
| |
| writel(val, host->ctl + (CTL_SD_CARD_CLK_CTL << 1)); |
| } |
| |
| static int uniphier_sd_start_signal_voltage_switch(struct mmc_host *mmc, |
| struct mmc_ios *ios) |
| { |
| struct tmio_mmc_host *host = mmc_priv(mmc); |
| struct uniphier_sd_priv *priv = uniphier_sd_priv(host); |
| struct pinctrl_state *pinstate = NULL; |
| u32 val, tmp; |
| bool uhs_en; |
| |
| switch (ios->signal_voltage) { |
| case MMC_SIGNAL_VOLTAGE_330: |
| val = UNIPHIER_SD_VOLT_330; |
| uhs_en = false; |
| break; |
| case MMC_SIGNAL_VOLTAGE_180: |
| val = UNIPHIER_SD_VOLT_180; |
| pinstate = priv->pinstate_uhs; |
| uhs_en = true; |
| break; |
| default: |
| return -ENOTSUPP; |
| } |
| |
| tmp = readl(host->ctl + UNIPHIER_SD_VOLT); |
| tmp &= ~UNIPHIER_SD_VOLT_MASK; |
| tmp |= FIELD_PREP(UNIPHIER_SD_VOLT_MASK, val); |
| writel(tmp, host->ctl + UNIPHIER_SD_VOLT); |
| |
| if (pinstate) |
| pinctrl_select_state(priv->pinctrl, pinstate); |
| else |
| pinctrl_select_default_state(mmc_dev(mmc)); |
| |
| uniphier_sd_uhs_enable(host, uhs_en); |
| |
| return 0; |
| } |
| |
| static int uniphier_sd_uhs_init(struct tmio_mmc_host *host) |
| { |
| struct uniphier_sd_priv *priv = uniphier_sd_priv(host); |
| struct device *dev = &host->pdev->dev; |
| struct device_node *np = dev->of_node; |
| struct of_phandle_args args; |
| int ret; |
| |
| priv->pinctrl = devm_pinctrl_get(mmc_dev(host->mmc)); |
| if (IS_ERR(priv->pinctrl)) |
| return PTR_ERR(priv->pinctrl); |
| |
| priv->pinstate_uhs = pinctrl_lookup_state(priv->pinctrl, "uhs"); |
| if (IS_ERR(priv->pinstate_uhs)) |
| return PTR_ERR(priv->pinstate_uhs); |
| |
| ret = of_parse_phandle_with_fixed_args(np, |
| "socionext,syscon-uhs-mode", |
| 1, 0, &args); |
| if (ret) { |
| dev_err(dev, "Can't get syscon-uhs-mode property\n"); |
| return ret; |
| } |
| priv->sdctrl_regmap = syscon_node_to_regmap(args.np); |
| of_node_put(args.np); |
| if (IS_ERR(priv->sdctrl_regmap)) { |
| dev_err(dev, "Can't map syscon-uhs-mode\n"); |
| return PTR_ERR(priv->sdctrl_regmap); |
| } |
| priv->sdctrl_ch = args.args[0]; |
| |
| return 0; |
| } |
| |
| static int uniphier_sd_probe(struct platform_device *pdev) |
| { |
| struct device *dev = &pdev->dev; |
| struct uniphier_sd_priv *priv; |
| struct tmio_mmc_data *tmio_data; |
| struct tmio_mmc_host *host; |
| int irq, ret; |
| |
| irq = platform_get_irq(pdev, 0); |
| if (irq < 0) |
| return irq; |
| |
| priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); |
| if (!priv) |
| return -ENOMEM; |
| |
| priv->caps = (unsigned long)of_device_get_match_data(dev); |
| |
| priv->clk = devm_clk_get(dev, NULL); |
| if (IS_ERR(priv->clk)) { |
| dev_err(dev, "failed to get clock\n"); |
| return PTR_ERR(priv->clk); |
| } |
| |
| priv->rst = devm_reset_control_get_shared(dev, "host"); |
| if (IS_ERR(priv->rst)) { |
| dev_err(dev, "failed to get host reset\n"); |
| return PTR_ERR(priv->rst); |
| } |
| |
| /* old version has one more reset */ |
| if (!(priv->caps & UNIPHIER_SD_CAP_EXTENDED_IP)) { |
| priv->rst_br = devm_reset_control_get_shared(dev, "bridge"); |
| if (IS_ERR(priv->rst_br)) { |
| dev_err(dev, "failed to get bridge reset\n"); |
| return PTR_ERR(priv->rst_br); |
| } |
| } |
| |
| tmio_data = &priv->tmio_data; |
| tmio_data->flags |= TMIO_MMC_32BIT_DATA_PORT; |
| tmio_data->flags |= TMIO_MMC_USE_BUSY_TIMEOUT; |
| |
| host = tmio_mmc_host_alloc(pdev, tmio_data); |
| if (IS_ERR(host)) |
| return PTR_ERR(host); |
| |
| if (host->mmc->caps & MMC_CAP_HW_RESET) { |
| priv->rst_hw = devm_reset_control_get_exclusive(dev, "hw"); |
| if (IS_ERR(priv->rst_hw)) { |
| dev_err(dev, "failed to get hw reset\n"); |
| ret = PTR_ERR(priv->rst_hw); |
| goto free_host; |
| } |
| host->ops.card_hw_reset = uniphier_sd_hw_reset; |
| } |
| |
| if (host->mmc->caps & MMC_CAP_UHS) { |
| ret = uniphier_sd_uhs_init(host); |
| if (ret) { |
| dev_warn(dev, |
| "failed to setup UHS (error %d). Disabling UHS.", |
| ret); |
| host->mmc->caps &= ~MMC_CAP_UHS; |
| } else { |
| host->ops.start_signal_voltage_switch = |
| uniphier_sd_start_signal_voltage_switch; |
| } |
| } |
| |
| if (priv->caps & UNIPHIER_SD_CAP_EXTENDED_IP) |
| host->dma_ops = &uniphier_sd_internal_dma_ops; |
| else |
| host->dma_ops = &uniphier_sd_external_dma_ops; |
| |
| host->bus_shift = 1; |
| host->clk_enable = uniphier_sd_clk_enable; |
| host->clk_disable = uniphier_sd_clk_disable; |
| host->set_clock = uniphier_sd_set_clock; |
| |
| ret = uniphier_sd_clk_enable(host); |
| if (ret) |
| goto free_host; |
| |
| uniphier_sd_host_init(host); |
| |
| tmio_data->ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34; |
| if (host->mmc->caps & MMC_CAP_UHS) |
| tmio_data->ocr_mask |= MMC_VDD_165_195; |
| |
| tmio_data->max_segs = 1; |
| tmio_data->max_blk_count = U16_MAX; |
| |
| sd_ctrl_write32_as_16_and_16(host, CTL_IRQ_MASK, TMIO_MASK_ALL); |
| |
| ret = devm_request_irq(dev, irq, tmio_mmc_irq, IRQF_SHARED, |
| dev_name(dev), host); |
| if (ret) |
| goto disable_clk; |
| |
| ret = tmio_mmc_host_probe(host); |
| if (ret) |
| goto disable_clk; |
| |
| return 0; |
| |
| disable_clk: |
| uniphier_sd_clk_disable(host); |
| free_host: |
| tmio_mmc_host_free(host); |
| |
| return ret; |
| } |
| |
| static void uniphier_sd_remove(struct platform_device *pdev) |
| { |
| struct tmio_mmc_host *host = platform_get_drvdata(pdev); |
| |
| tmio_mmc_host_remove(host); |
| uniphier_sd_clk_disable(host); |
| tmio_mmc_host_free(host); |
| } |
| |
| static const struct of_device_id uniphier_sd_match[] = { |
| { |
| .compatible = "socionext,uniphier-sd-v2.91", |
| }, |
| { |
| .compatible = "socionext,uniphier-sd-v3.1", |
| .data = (void *)(UNIPHIER_SD_CAP_EXTENDED_IP | |
| UNIPHIER_SD_CAP_BROKEN_DMA_RX), |
| }, |
| { |
| .compatible = "socionext,uniphier-sd-v3.1.1", |
| .data = (void *)UNIPHIER_SD_CAP_EXTENDED_IP, |
| }, |
| { /* sentinel */ } |
| }; |
| MODULE_DEVICE_TABLE(of, uniphier_sd_match); |
| |
| static struct platform_driver uniphier_sd_driver = { |
| .probe = uniphier_sd_probe, |
| .remove_new = uniphier_sd_remove, |
| .driver = { |
| .name = "uniphier-sd", |
| .probe_type = PROBE_PREFER_ASYNCHRONOUS, |
| .of_match_table = uniphier_sd_match, |
| }, |
| }; |
| module_platform_driver(uniphier_sd_driver); |
| |
| MODULE_AUTHOR("Masahiro Yamada <yamada.masahiro@socionext.com>"); |
| MODULE_DESCRIPTION("UniPhier SD/eMMC host controller driver"); |
| MODULE_LICENSE("GPL v2"); |